Service manual

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 46
Operation/Procedure
(Adjustment mode selection)
1) Select the number corresponding to the copy mode to be
adjusted with 10-key.
SPF odd pixel (Front surface copy), SPF even pixel (Front sur-
face copy), SPF (Back surface copy) (Select one of 3 - 5.)
2) Press [SATART] key.
(Copy density level adjustment)
1) Enter the density correction value with 10-key.
2) Press [P] key or [START] key.
(Copy condition setting in this simulation)
To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
START key is pressed, the adjustment value is set and
copying is performed.
• "Set value - 128" is added to the shading adjustment value (SIM
46-17).
Operation/Procedure
1) Select "SCANNER EXP. LEVEL" with 10-key.
2) Press [START] key.
3) Enter the image density adjustment value.
4) Press [P] key or [START] key.
NOTE: When this simulation is performed to adjust the scan image
densities, all the image densities in all the scan modes are
changed to the image density level set with this simulation.
That is, the image densities set with SIM 46-22, 23, 24, 25,
and 45 are changed to the image density level set with this
simulation.
NOTE: Only the set value is changed and no printing is performed.
46-20
Purpose Adjustment
Function
(Purpose)
Used to adjust the copy density correction in the
SPF copy mode for the document table copy
mode. The adjustment is made so that the copy
density becomes the same as that of the
document table copy mode.
Section SPF
Item Picture quality Density
Item Content
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1: TRAY1
2: TRAY2
3: TRAY3
4: TRAY4
5: Manual feed
––
1 PRINT START Print start (Default) ––
2 EXP LEVEL Exposure level selection
3: Exposure level 1.0
4: Exposure level 1.5
5: Exposure level 2.0
6: Exposure level 2.5
7: Exposure level 3.0
8: Exposure level 3.5
9: Exposure level 4.0
10: Exposure level 4.5
11: Exposure level 5.0
––
3 SPF (ODD) SPF (front) (odd pixel) 0 - 255 128
4 SPF (EVEN) SPF (front) (even pixel)
5 DSPF DSPF (Back surface)
46-21
Purpose Adjustment
Function
(Purpose)
Used to adjust the scanner exposure level in all
the scanner modes.
Item Picture quality Density
Item
Set
range
Default
0 SCANNER EXP. LEVEL Image density level 0 - 99 50
SIMULATION 46-20
1
Press [CUSTOM SETTINGS] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. INPUT VALUE 0-255, AND PRESS
START.
3.SPF(ODD)
128
Press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. NOW PRINTING.
Press [CUSTOM SETTINGS] key,
or terminate copying.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-5, AND PRESS START.
(FEED TRAY)
2.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Press [START] key or
press [CUSTOM SETTINGS] key.
1
Select 0, and
press [START] key.
Select 1,
and press
[START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 3-8, AND PRESS START.
(EXP. LEVEL SELECT)
3.1.0 4.1.5 5.2.0
6.2.5 7.3.0 8.3.5
9.4.0 10.4.5 11.5.0
1
Press [START] key or
press [CUSTOM SETTINGS] key.
Select 2, and
press [START] key.
OC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.SPF(ODD) 128
4.SPF(EVEN) 128
5.DSPF 128
Select other than 0 - 2, and press [START] key.