Service manual

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 62
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 2 - 12.)
2) Press [START] key.
(Resist adjustment)
1) Enter the resist adjustment value with 10-key.
2) Press [START] key.
When [START] key is pressed, the adjustment value is set and
paper feed and copying are performed.
(Copy condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex print mode.
NOTE: When [P] key is pressed after entering the adjustment
value in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
Scanner mode
10 OC (LEAD_EDGE) OC lead edge 0 - 10
(Unit 1mm)
0
(0mm)
11 OC (FRONT/REAR) OC side
12 OC (TRAIL_EDGE) OC rear edge
13 SPF (LEAD_EDGE) SPF lead edge
14 SPF (FRONT/REAR) SPF side
15 SPF (TRAIL_EDGE) SPF rear edge
16 CIS (LEAD_EDGE) CIS lead edge
17 CIS (FRONT/REAR) CIS side
18 CIS (TRAIL_EDGE) CIS rear edge
Press [START] key. Press [CUSTOM SETTINGS] key.
51
51-2
Purpose Adjustment
Function
(Purpose)
Used to adjust the contact pressure of paper on
the resist roller of each section (each paper feed,
duplex feed and SPF paper feed of the copier).
(This adjustment is required when the print image
position variations are considerably great or when
paper jams occur frequently.)
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
Item Set range Default
1
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0
4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0
7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0
[SCN]
10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0
13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0
16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0
0
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND
PRESS START.
1.OC(LEAD_EDGE)
Item
Set
range
Default
AR-
M351U/
M355U
AR-
M451U/
M455U
0 TRAY SELECT Paper feed tray
selection
1 - 5 –
1 PRINT START Copy start (Initial
value)
––
2 TRAY1 Tray 1 resist
adjustment value
0 - 99 65 60
3 TRAY2 Tray 2 resist
adjustment value
55 50
4 DESK Desk resist
adjustment value
55 50
5 BPT Manual tray resist
adjustment value
60 55
6 ADU ADU resist
adjustment value
55 50
7 SPF (HIGH) SPF resist
adjustment value
(High speed)
60 60
8 SPF (LOW) SPF resist
adjustment value
(Low speed)
75 75
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1 TRAY1 TRAY1
2 TRAY2 TRAY2
3 TRAY3 TRAY3
4 TRAY4 TRAY4
5 BPT Manual feed