Service manual

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 71
Operation/Procedure
(Various print patterns output) (Table 1)
1) Select PRINT PATTERN with 10-key.
2) Enter the number corresponding to the print pattern to be
printed with 10-key.
3) Press [START] key.
4) Select PRINT START with 10-key.
5) Press [START] key.
(Print condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Select TRAY SELECT with 10-key.
2) Press [START] key.
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
∗ To adjust the print density, perform the following procedures.
1) Select DENSITY with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
∗ To set the print quantity, perform the following procedures.
1) Select MULTI with 10-key.
2) Enter the print quantity with 10-key.
3) Press [START] key.
∗ To set the print quality mode, perform the following procedures.
1) Select MODE with 10-key.
2) Enter the number corresponding to the print quality mode with
10-key.
3) Press [START] key.
∗ To set the print level, perform the following procedures.
1) Select LEVEL with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
NOTE: In some print patterns, changing the level may not change
the picture quality.
∗ To set duplex/simplex print, perform the following procedures.
1) Select DUPLEX with 10-key.
2) Enter the number corresponding to the operation mode with
10-key.
3) Press [START] key.
(Table 1)
(Note 1) Print pattern
64
64-1
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the printer section
(self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
Item Operation
0 TRAY SELECT
1. TRAY1
2. TRAY2
3. TRAY3
4. TRAY4
5. BPT
Paper feed tray
1: Tray 1
2: Tray 2
3: Tray 3
4: Tray 4
5: Manual feed
1 PRINT START Print execution (Printing of the set
data is executed.)
2 PRINT PATTERN Print pattern (Note 1)
3 DENSITY Graphic density (Valid only when
No. 79, 80 or 84 is selected.)
4 MULTI Print quantity
5MODE
1. STANDARD
2. SMOOTHING
3. TONER SAVE
4. HALF TONE
5. SMOOTHING + TONER
SAVE
6. SMOOTHING + HALF TONE
7. TONER SAVE + HALF
TONE
8. SMOOTHING + TONER
SAVE + HALF TONE
Print mode
1. Standard
2. Smoothing ON
3. Smoothing ON
3. Toner save ON
4. Half tone ON
5. Smoothing + toner save
6. Smoothing + half tone
7. Toner save + half tone
8. Smoothing + toner save +
half tone
6 LEVEL (Parameter of print image
process)
7 DUPLEX
1. NO
2. YES
Duplex
0: NO (Simplex)
1: YES (Duplex)
No
Engine
pattern
Controller Pattern Note
1 ❍ For off-center adjustment
2 ❍ Main scanning direction 1 by 5
3 ❍ Main scanning direction 1mm-
pitch
4 ❍ Main scanning direction 3 by 3
5 ❍ Sub scanning direction 1 by 1
6 ❍ Sub scanning direction 1 by 5
7 ❍ Sub scanning direction 2 by 4
8 ❍ Sub scanning direction 3 by 3
9 ❍ Right oblique 1 by 2
10 ❍ Right oblique 1 by 5
11 ❍ Right oblique 2 by 4
12 ❍ Right oblique 3 by 3
13 ❍ Left oblique 1 by 2
14 ❍ Left oblique 1 by 5
15 ❍ Left oblique 2 by 4
16 ❍ Left oblique 3 by 3
17 ❍ Dot 1 by 1
18 ❍ Dot 3 by 3
19 ❍ Dot
20 ❍ Solid black
21 ❍ Main scanning direction 1 by 1
22 ❍ Main scanning direction 5 by 1
23 ❍ Main scanning direction 4 by 2
24 ❍ Main scanning direction 3 by 3
25 ❍ Sub scanning direction 1 by 1
26 ❍ Sub scanning direction 5 by 1
27 ❍ Sub scanning direction 4 by 2
28 ❍ Sub scanning direction 3 by 3
29 ❍ Right oblique 2 by 1
30 ❍ Right oblique 5 by 1
31 ❍ Right oblique 4 by 2
32 ❍ Right oblique 3 by 3
33 ❍ Left oblique 2 by 1
34 ❍ Left oblique 5 by 1
35 ❍ Left oblique 4 by 2
36 ❍ Left oblique 3 by 3