Owner's Manual
Table Of Contents
- Part 1: General Information
- PRODUCT CONFIGURATIONS
- OPERATION MANUALS
- INSTALLATION REQUIREMENTS
- CAUTIONS
- CONTENTS
- INTRODUCTION
- MAIN FEATURES
- PART NAMES AND FUNCTIONS
- TURNING THE POWER ON AND OFF
- AUDITING MODE
- LOADING PAPER
- Identifying the trays
- Loading paper in paper tray 1 - tray 2
- Loading paper in paper tray 3
- Changing the paper size in paper tray 3
- Changing the paper size in paper tray 4
- Loading paper in paper tray 5 (optional large capacity tray)
- Specifications (optional large capacity tray)
- Loading paper in the bypass tray
- Specifications of paper trays (Types and sizes of paper that can be used in the trays)
- Setting the paper type and paper size
- Setting the paper size when a special size is loaded
- CUSTOM SETTINGS
- REPLACING THE TONER CARTRIDGES
- STORAGE OF SUPPLIES
- MISFEED REMOVAL
- REMOVING AN ORIGINAL MISFEED
- TROUBLESHOOTING
- FINISHER AND SADDLE STITCH FINISHER
- INSERTER
- Part 2: Copier Operation
- AUTOMATIC DOCUMENT FEEDER
- PLACING ORIGINALS
- CHECKING THE SIZE OF A PLACED ORIGINAL
- STORING, DELETING, AND USING ORIGINAL SIZES
- NORMAL COPYING
- ADJUSTING THE EXPOSURE
- REDUCTION/ENLARGEMENT/ZOOM
- SPECIAL PAPERS
- SPECIAL MODES
- General procedure for using special functions
- Margin shift
- Erase
- Dual page copy
- Pamphlet copy
- Job build
- Tandem copy
- Covers/inserts
- About the explanations of covers and inserts
- Preparations for using covers and inserts
- Procedure for inserting front and back cover paper
- Procedure for adding inserts
- Checking, editing, and deleting cover/insert pages
- Examples of covers and inserts
- Symbols used for covers and inserts
- Covers (One-sided copying of one-sided originals)
- Covers (Two-sided copying of one-sided originals)
- Covers (One-sided copying of Two-sided originals)
- Covers (Two-sided copying of two-sided originals)
- Inserts (One-sided copying of one-sided originals)
- Inserts (One-sided copying of two-sided originals)
- Transparency film with insert sheets
- Multi shot
- Book copy
- Tab copy
- Card shot
- Mirror image
- B/W reverse
- STORING, USING AND DELETING JOB PROGRAMS
- INTERRUPTING A COPY RUN
- USER MAINTENANCE
- TROUBLESHOOTING
- OVERVIEW
- TO USE THE DOCUMENT FILING FUNCTION
- SAVING A DOCUMENT IMAGE FILE
- CALLING UP AND USING A FILE
- CUSTOM SETTINGS
- ENTERING CHARACTERS
- TROUBLESHOOTING
- SPECIFICATIONS
- INDEX
![](/manual/sharp/ar-m620/owner-s-manual-english/images/img-28.png)
2-2
LOADING PAPER
If the paper runs out during printing, a message will appear in the display.
Follow the procedure below to load paper.
Identifying the trays
The trays are identified using numbers as shown below.
For the types and sizes of paper that can be used in each tray, see page 2-8.
Loading paper in paper tray 1 - tray 2
8-1/2" x 11" or A4 size paper can be loaded in tray 1. 8-1/2" x 11", A4 or B5 size paper can be loaded in tray 2. These
are parallel large-capacity trays that allow a total of approximately 2000 sheets of SHARP standard paper (20lbs.
(80g/m
2
)) to be loaded. If you wish to change the paper size of tray 1 or tray 2, please consult your dealer (the paper
size must be changed by a service technician).
1
Pull out paper tray 1-tray 2.
Gently pull the tray out
until it stops.
2
Load paper in the left and right trays.
Lift the paper guide and
load paper in tray 1.*
1
Approximately 800 sheets
of SHARP standard paper
(20lbs.(80g/m
2
))
can be
loaded.
Be sure to return the
paper guide to its
original position after
loading the paper.
Load paper in tray 2.*
1
Approximately 1200
sheets of SHARP
standard paper
(20lbs.
(80g/m
2
))
can be loaded.
*1 The paper stack must not be higher than the indicator line.
Tray 1
This is the left large capacity tray.
Tray 3
Tray 4
Tray 2
This is the right large capacity tray.
Tray 5
This is an optional large capacity tray.
Bypass tray
1
2
3
4
5
6
NOTES
● Do not use curled or folded paper. Doing so may cause a misfeed.
● Do not place heavy objects or press hard on any tray which is pulled out.
● Do not place objects on the large-capacity tray. This may damage the tray or interfere with operation.
● Load paper with the print side face up. However, when the paper type is set to "PRE-PRINTED" or "LETTER
HEAD", load the paper face down*.
* If the two-sided function is disabled using "DISABLING OF DUPLEX" in the key operator programs(page 11
of the key operator's guide), load the paper face up.
Indicator line
Indicator line