Owner's Manual
Table Of Contents
- Part 1: General Information
- PRODUCT CONFIGURATIONS
- OPERATION MANUALS
- INSTALLATION REQUIREMENTS
- CAUTIONS
- CONTENTS
- INTRODUCTION
- MAIN FEATURES
- PART NAMES AND FUNCTIONS
- TURNING THE POWER ON AND OFF
- AUDITING MODE
- LOADING PAPER
- Identifying the trays
- Loading paper in paper tray 1 - tray 2
- Loading paper in paper tray 3
- Changing the paper size in paper tray 3
- Changing the paper size in paper tray 4
- Loading paper in paper tray 5 (optional large capacity tray)
- Specifications (optional large capacity tray)
- Loading paper in the bypass tray
- Specifications of paper trays (Types and sizes of paper that can be used in the trays)
- Setting the paper type and paper size
- Setting the paper size when a special size is loaded
- CUSTOM SETTINGS
- REPLACING THE TONER CARTRIDGES
- STORAGE OF SUPPLIES
- MISFEED REMOVAL
- REMOVING AN ORIGINAL MISFEED
- TROUBLESHOOTING
- FINISHER AND SADDLE STITCH FINISHER
- INSERTER
- Part 2: Copier Operation
- AUTOMATIC DOCUMENT FEEDER
- PLACING ORIGINALS
- CHECKING THE SIZE OF A PLACED ORIGINAL
- STORING, DELETING, AND USING ORIGINAL SIZES
- NORMAL COPYING
- ADJUSTING THE EXPOSURE
- REDUCTION/ENLARGEMENT/ZOOM
- SPECIAL PAPERS
- SPECIAL MODES
- General procedure for using special functions
- Margin shift
- Erase
- Dual page copy
- Pamphlet copy
- Job build
- Tandem copy
- Covers/inserts
- About the explanations of covers and inserts
- Preparations for using covers and inserts
- Procedure for inserting front and back cover paper
- Procedure for adding inserts
- Checking, editing, and deleting cover/insert pages
- Examples of covers and inserts
- Symbols used for covers and inserts
- Covers (One-sided copying of one-sided originals)
- Covers (Two-sided copying of one-sided originals)
- Covers (One-sided copying of Two-sided originals)
- Covers (Two-sided copying of two-sided originals)
- Inserts (One-sided copying of one-sided originals)
- Inserts (One-sided copying of two-sided originals)
- Transparency film with insert sheets
- Multi shot
- Book copy
- Tab copy
- Card shot
- Mirror image
- B/W reverse
- STORING, USING AND DELETING JOB PROGRAMS
- INTERRUPTING A COPY RUN
- USER MAINTENANCE
- TROUBLESHOOTING
- OVERVIEW
- TO USE THE DOCUMENT FILING FUNCTION
- SAVING A DOCUMENT IMAGE FILE
- CALLING UP AND USING A FILE
- CUSTOM SETTINGS
- ENTERING CHARACTERS
- TROUBLESHOOTING
- SPECIFICATIONS
- INDEX
FINISHER AND SADDLE STITCH FINISHER
3-8
■
■■
■ Replacing the cartridge in the saddle stitch finisher
Only when the saddle stitch finisher (AR-F16) is installed.
1
Open the lower cover of the saddle stitch
finisher.
When an optional
inserter is installed,
open the front cover of
the inserter before
opening the lower cover
of the finisher.
2
Slide out the saddle stitch unit carefully
toward the front.
3
(1) Grasp the grip of the saddle staple
holder and pull it out.
(2) While still grasping the grip, rotate the
saddle staple holder 90° in the direction of
the arrow (rotate to the right).
4
Remove the empty staple case and set a
new one.
Replace both staple
cases with new ones.
Remove the cover from
the staple cartridge and
then install the cartridge.
5
Return the saddle stitch holder and the
saddle stitch unit to their respective
original positions.
6
Make sure that the finisher is firmly
attached to the machine and that 11" x 17",
8-1/2" x 11"R, or 8-1/2" x 14" (A3, A4R, or
B4) size paper is loaded.
If one of the above paper sizes is not set, test
stapling cannot be performed.
7
Close the lower cover of the finisher.
Test stapling is
automatically performed
on a blank sheet.
This operation is carried
out to avoid blank
stapling.
(1)
(2)
NOTE
If test stapling fails to take place, repeat steps 1 to 7.