Owner's Manual
Table Of Contents
- Part 1: General Information
- PRODUCT CONFIGURATIONS
- OPERATION MANUALS
- INSTALLATION REQUIREMENTS
- CAUTIONS
- CONTENTS
- INTRODUCTION
- MAIN FEATURES
- PART NAMES AND FUNCTIONS
- TURNING THE POWER ON AND OFF
- AUDITING MODE
- LOADING PAPER
- Identifying the trays
- Loading paper in paper tray 1 - tray 2
- Loading paper in paper tray 3
- Changing the paper size in paper tray 3
- Changing the paper size in paper tray 4
- Loading paper in paper tray 5 (optional large capacity tray)
- Specifications (optional large capacity tray)
- Loading paper in the bypass tray
- Specifications of paper trays (Types and sizes of paper that can be used in the trays)
- Setting the paper type and paper size
- Setting the paper size when a special size is loaded
- CUSTOM SETTINGS
- REPLACING THE TONER CARTRIDGES
- STORAGE OF SUPPLIES
- MISFEED REMOVAL
- REMOVING AN ORIGINAL MISFEED
- TROUBLESHOOTING
- FINISHER AND SADDLE STITCH FINISHER
- INSERTER
- Part 2: Copier Operation
- AUTOMATIC DOCUMENT FEEDER
- PLACING ORIGINALS
- CHECKING THE SIZE OF A PLACED ORIGINAL
- STORING, DELETING, AND USING ORIGINAL SIZES
- NORMAL COPYING
- ADJUSTING THE EXPOSURE
- REDUCTION/ENLARGEMENT/ZOOM
- SPECIAL PAPERS
- SPECIAL MODES
- General procedure for using special functions
- Margin shift
- Erase
- Dual page copy
- Pamphlet copy
- Job build
- Tandem copy
- Covers/inserts
- About the explanations of covers and inserts
- Preparations for using covers and inserts
- Procedure for inserting front and back cover paper
- Procedure for adding inserts
- Checking, editing, and deleting cover/insert pages
- Examples of covers and inserts
- Symbols used for covers and inserts
- Covers (One-sided copying of one-sided originals)
- Covers (Two-sided copying of one-sided originals)
- Covers (One-sided copying of Two-sided originals)
- Covers (Two-sided copying of two-sided originals)
- Inserts (One-sided copying of one-sided originals)
- Inserts (One-sided copying of two-sided originals)
- Transparency film with insert sheets
- Multi shot
- Book copy
- Tab copy
- Card shot
- Mirror image
- B/W reverse
- STORING, USING AND DELETING JOB PROGRAMS
- INTERRUPTING A COPY RUN
- USER MAINTENANCE
- TROUBLESHOOTING
- OVERVIEW
- TO USE THE DOCUMENT FILING FUNCTION
- SAVING A DOCUMENT IMAGE FILE
- CALLING UP AND USING A FILE
- CUSTOM SETTINGS
- ENTERING CHARACTERS
- TROUBLESHOOTING
- SPECIFICATIONS
- INDEX
FINISHER AND SADDLE STITCH FINISHER
3-13
3
Troubleshooting finisher/saddle stitch finisher problems
Check the list below before calling for service.
* When a hole punch module is installed
Problem Check Solution or cause
Stapling position is
not correct
(including saddle
stitch).
Stapling position not set properly?
Check the stapling position setting. (See page
3-4.)
The finisher/saddle
stitch finisher does
not operate.
Are any finisher/saddle stitch finisher
covers open?
Close all covers. (See step 7 on page 3-7 and
step 7 on page 3-11.)
Message indicating need to remove paper
from the stapler compiler displayed?
Remove all remaining paper from the stapler
compiler. (For the stapler compiler, see "Part
names" on page 3-2.)
Stapling cannot be
performed (including
saddle stitch).
Message to check the staple unit
displayed?
Remove jammed staples. (See pages 3-9 and
3-10.)
Message to add staples displayed?
Replace the staple cartridge. (See pages 3-7
and 3-8.) Check that a staple cartridge has
been installed. (See pages 3-7 and 3-8.)
Different sizes of paper mixed together?
Stapling cannot be performed on mixed paper
sizes.
The paper is badly curled.
The quality and type of some papers may
cause bad curling that prevents stapling.
Take the paper out of the tray or bypass tray,
turn it around, and reload it so that the top and
bottom edges are reversed.
Saddle stitch cannot
be selected.
The paper type of the selected paper tray
is set to heavy paper.
Saddle stitch is not possible on heavy paper.
However, when cover insertion is selected,
saddle stitch is possible on a single sheet of
heavy paper inserted for use as a cover.
The punch hole
positions are not
correct.*
The punch function is not set to the correct
punch positions.
Check the allowed hole punch positions. (See
page 3-5.)
Cannot be punched.*
Message to check the punch module
displayed?
Dispose of punch scraps. (See page 3-10.)
Mixed paper sizes.
Punching is not possible when different paper
sizes are mixed together.
The paper is badly curled.
The quality and type of some papers may
cause bad curling that prevents punching.
Take the paper out of the tray or bypass tray,
turn it around, and reload it so that the top and
bottom edges are reversed.