MODEL AR-164 DIGITAL LASER COPIER/PRINTER OPERATION MANUAL Page • GETTING STARTED • MAKING COPIES • SPECIAL FEATURES • STATUS INDICATORS • GENERAL INFORMATION • OPTIONAL EQUIPMENT 2 13 28 38 46 65
FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit. Model Number AR-164 Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number CAUTIONS Follow the cautions below when using this copier. ● ● The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes.
CONTENTS Page GETTING STARTED ● ● ● ● ● INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . 4 – Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 – Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 COPIER INSTALLATION . . . . . . . . . . . . . . . .
INTRODUCTION GETTING STARTED This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. Introduction This copier can be used as a laser printer and as a facsimile machine by installing optional components.
MAIN FEATURES GETTING STARTED GETTING STARTED High-speed laser copying ● First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on). ● Copying speed is 16 copies/min., which adapts to business use, allowing improvement of working efficiency. High-quality digital image ● High-quality copying at 600 dpi is performed. In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.
PART NAMES AND FUNCTIONS GETTING STARTED Overall layout Part names and functions Document feeder cover Open to make copies from the original table. Paper tray Holds 250 sheets of copy paper. Original table All originals which cannot be copied from the SPF must be copied here. Side cover Open to remove misfeeds and to service the copier. Handles Use to move the copier. Power switch Press to turn copier power on and off. Operation panel All copier controls are located here for easy operation.
PART NAMES AND FUNCTIONS GETTING STARTED GETTING STARTED Single pass feeder (SPF) Part names and functions Document feeder tray Holds up to 30 originals. Original guides Adjust to the size of the originals. Feeding roller cover Open to remove misfed originals. Exit area Finished originals are output here. Toner cartridge lock release lever Use to unlock the toner cartridge. Toner cartridge Contains toner. Photoconductive drum Copy images are formed on the photoconductive drum.
PART NAMES AND FUNCTIONS Operation panel GETTING STARTED Part names and functions INTERRUPT key and indicator (p. 25) Interrupts a copy run. Copy quantity display Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are made. Also see items and . ZOOM indicator (p.19) Lights up when a zoom ratio is set. Copy ratio display key (p. 19) Press and hold down during standby to display the copy ratio in the copy quantity display. Zoom keys (p.
PART NAMES AND FUNCTIONS GETTING STARTED GETTING STARTED Part names and functions 1st display Press and hold down the key. 2nd display 12,345 sheets output Note: 11" x 17" size copies are counted as two copies. CLEAR key Clears the copy quantity display or terminates a copy run. START key and indicator Copying is possible when the indicator is on. Press to start copying. CLEAR ALL ( ) key Clears all selected settings and returns the copier to the initial settings.
COPIER INSTALLATION GETTING STARTED Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
CAUTIONS ON HANDLING GETTING STARTED GETTING STARTED Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object. Cautions on handling Store spare toner cartridges in a cool dry place without removing from the package before use. If they are exposed to direct sunlight or excessive heat, poor copies may result. Do not touch the photoconductive drum (green portion).
LOADING COPY PAPER GETTING STARTED To save space, this copier has been designed with an adjustable front-loading tray, which is easily opened for paper loading. For best results, use only SHARP recommended paper. (See page 60.) The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed.
LOADING COPY PAPER GETTING STARTED GETTING STARTED Loading copy paper Changing the copy paper size in the tray Left guide 1 Gently lift and pull out the paper tray until it stops. 2 Push the pressure plate down until it locks in place. 3 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper. 4 Move the left guide to the appropriate slot as marked on the tray. ● When using 5-1/2" x 8-1/2" copy paper, load it into the uppermost paper tray.
LOADING COPY PAPER GETTING STARTED Loading copy paper 8 To set the selected paper size, press the PAPER SIZE ENTER key. 9 Use the TRAY SELECT key to select the paper tray of which the paper size has been changed. ● ● 10 Each time the ORIGINAL SIZE ENTER key is pressed, a paper size will be indicated with a paper size indicator. Press the START key and then the PAPER SIZE ENTER key.
AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 49 for setting the auditing mode. 2 ● As each digit is entered, the dashes in the copy quantity display will disappear. ● After the number is entered, the copy quantity display will change to 0. ● If an unassigned number is entered, “––– ” will appear again in the copy quantity display, indicating that the number was not accepted.
NORMAL COPYING Using the SPF MAKING COPIES This copier has two document input stations –– a single pass feeder (SPF) for automatic document feeding and an original table for manual handling of bound documents. The SPF is designed to hold up to 30 originals measuring from 5-1/2" x 8-1/2" to 11" x 17" and in the weight range of 15 to 24 lbs. ● Be sure to remove any staples or paper clips from the originals. ● Damaged or crumpled originals may misfeed in the SPF.
NORMAL COPYING 6 Adjust the copy density. ● Automatic exposure is the standard initial setting for this copier. In this mode, the characteristics of the original are “read” by the exposure system and adjustments are automatically made. This optimizes the contrast of the copied images by reducing the effect of colored or shaded background areas. See page 26 to adjust the automatic exposure level.
NORMAL COPYING Using the original table Power on 1 Turn the power switch on. ● ● MAKING COPIES ● 2 Place the original face down on the original table. Align it with the original size scale. ● Normal copying Image loss (max. 5/32" (4 mm)) can occur at the leading and trailing edges of the copies. Also image loss (max. 5/32" (4 mm) in total) can occur along the other edges of the copies. 3 Close the platen cover.
NORMAL COPYING ● For photographs, select PHOTO and then adjust with the light ( and dark ( ) keys as desired. ● There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously. ) Set the number of copies using the numeric keys.
REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the PRESET RATIO selector ( , ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. MAKING COPIES Automatic Reduction/enlargement/zoom 1 Place the original in the document feeder tray or on the original table.
REDUCTION/ENLARGEMENT/ZOOM Manual 2 Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio. ● ● When a zoom ( , ) key is pressed, the ZOOM indicator will light up and the zoom ratio will be displayed in the copy quantity display for at least two seconds. ● To verify a zoom setting without changing the zoom ratio, press and hold down the copy ratio display ( ) key. When the key is released, the display will return to the copy quantity display.
BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. For special purpose papers, the original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies.
BYPASS FEED (special paper) Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper or envelopes. 6 Press the START key. 21 Bypass feed (special paper) 5 MAKING COPIES 4 Press the TRAY SELECT key to select the bypass tray.
TWO-SIDED COPYING Two-sided copies can be made on this copier using the bypass tray. MAKING COPIES 1 Place the first original on the original table and make a copy. ● Two-sided copying 2 Replace the first original with the second original and close the platen cover. ● ● ● 3 Make sure that the first and second originals are oriented in the same way on the original table.
SORT/GROUP MAKING COPIES This copier has two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. The sort/group feature cannot be used with the dual page copy feature. To change the SORT/GROUP mode, press the SORT/GROUP key to select the desired mode. ● The capacity of the paper output tray is 250 sheets (150 sheets if an optional job separator tray kit (AR-TR2) is installed).
SORT/GROUP Copying in the sort mode When copying in the sort mode, the original image will be stored in the copier memory each time an original is scanned and copying will start after all originals have been scanned. MAKING COPIES 1 Set the originals face up in the document feeder tray. 2 Press the SORT/GROUP key to select the SORT mode. 3 Ensure that the copy paper size in the paper tray is the same size as the originals. ● The original table cannot be used for sort copying.
INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. ● SORT or GROUP cannot be selected during interrupt copying. ● ● 2 When the copier stops, remove the original(s) and set the original(s) for interrupt copying. 3 4 5 Select the desired available copier functions. 6 When all INTERRUPT copies are finished, press the INTERRUPT key again to cancel the INTERRUPT mode, and remove the original used for interrupt copying. Set the number of copies.
AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the SPF respectively. To set the level for the SPF, place an original in the document feeder tray and make sure that the SPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the SPF indicator d2oes not light up.
TONER SAVE MODE This mode reduces toner consumption by approximately 10% in the automatic and manual exposure modes. Copies will be lighter but still adequate for general use. Selection of this mode does not affect the PHOTO mode. Follow the procedure below for setting the toning level. Toner save mode 2 Press and hold down the AUTO/MANUAL/PHOTO key for approximately 5 seconds. MAKING COPIES 1 Press the AUTO/MANUAL/PHOTO key to select the MANUAL mode.
XY ZOOM Original Copy The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. This feature cannot be used with the 2 in 1 or 4 in 1 feature. To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.) SPECIAL FEATURES 1 Place the original in the document feeder tray or on the original table. 2 Press the XY-ZOOM key.
XY ZOOM 5 Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the horizontal direction in a similar manner as for the vertical direction. 6 Press the copy ratio display ( ● The selected ratio for the horizontal direction will be entered and the display will change to the copy quantity display. ● To verify the copy ratios, press and hold down the copy ratio display ( ) key. The vertical and horizontal ratios will be alternately displayed.
B/W REVERSE Original Copy The B/W REVERSE feature is used to reverse black and white areas. SPECIAL FEATURES When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the MANUAL mode. Other exposure modes cannot be selected. Even if this feature is canceled, the MANUAL mode will not automatically be canceled. 1 Place the original in the document feeder tray or on the original table. 2 Press the B/W REVERSE key. 3 Check the copy paper size.
DUAL PAGE COPY Original Copy The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the original table. It is especially useful when copying books and other bound documents. This feature cannot be used with the 2 in 1 or 4 in 1 feature and sort/group feature. If the AUTO IMAGE feature has been selected, this feature cannot be selected. To use the DUAL PAGE COPY feature with the XY ZOOM feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature.
ROTATION COPYING Original Paper Copy Example: Copying from an 11" x 17" original onto 8-1/2" x 11" paper SPECIAL FEATURES Rotation copying 32 If user program No. 7 is set, the image of the original will rotate when the orientation of the original does not match that of the copy paper. Rotation copying will function only if the AUTO PAPER SELECT mode or AUTO IMAGE mode has been selected. Even if user program No.
2 IN 1 OR 4 IN 1 2 in 1 copying 4 in 1 copying The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a specified order, onto one sheet. ● These features cannot be used with the dual page copying, XY zoom, erase, or margin shift features. ● Copies can be made with or without the border lines shown in the illustration. See user program No.6 on page 46. ● The order of originals which will be arranged on the copies can be selected by user programs.
2 IN 1 OR 4 IN 1 SPECIAL FEATURES 2 in 1 or 4 in 1 34 4 Enter the desired pattern number using a numeric key. 5 Press the START key. 6 Press the 2 IN 1 / 4 IN 1 key to complete the selection. 7 Set the number of copies. 8 Press the START key. ● ● ● ● The entered number will blink in the copy quantity display. For layout pattern numbers, see the previous page. The entered number will light up steadily. The copy ratio will be calculated automatically.
ERASE Edge erase A This copier has an edge erase mode and a center erase mode. A Center erase AB AB ● Edge erase can be used to eliminate shadow lines around the edges of copies caused when thick paper or a book is used as an original. ● Center erase can be used to eliminate the shadow produced by the bindings of bound documents. ● Edge + center erase can be used to eliminate shadow lines around the edges of copies and to eliminate the shadow at the center of copies.
ERASE SPECIAL FEATURES Erase 36 4 Set the number of copies. 5 Press the START key.
MARGIN SHIFT Original Copy The MARGIN SHIFT feature automatically shifts the text or image to the right to increase the left margin by approximately 1/4". ● This feature cannot be used with the 2 in 1 or 4 in 1 feature. Expanded margin Margin is expanded here. 1 Place the original in the document feeder tray or on the original table. ● When copying from the original table, set the original face down so that the margin side is positioned at the right side.
TONER CARTRIDGE REPLACEMENT When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner cartridge replacement required ( ) indicator blinks, the toner cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below.
TONER CARTRIDGE REPLACEMENT 5 Gently insert the toner cartridge along the guides until it locks in place while pushing the lock release lever. If dirt or dust is adhered to the toner cartridge, remove it before installing the cartridge. 6 Remove the tape from the shutter. Pull the shutter out of the toner cartridge as shown in the illustration. Discard the shutter. 7 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover.
MISFEED REMOVAL The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location. If paper is accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. For misfeeds in optional equipment, see their section of the operation manual. First confirm the misfeed location. ( P. 40) ( P. 41, 44) ( P.
MISFEED REMOVAL Location C 3 If the misfed original cannot be removed in steps 1 and 2, remove the misfed original from the exit area. Open the document feeder cover and rotate the roller in the direction indicated by the arrow if needed. If the misfed original cannot be easily removed from the exit area, open the front part of the document feeder tray to remove the original. 4 Open and close the document feeder cover to cancel the misfeed location indicator.
MISFEED REMOVAL 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to “B. Misfeed in the fusing area”. If the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”. If paper is misfed here, proceed to “A. Misfeed in the paper feed area”. A. Misfeed in the paper feed area Roller rotating knob 1 Push gently on both sides of the front cover and open it.
MISFEED REMOVAL Roller rotating knob 2 Turn the roller rotating knob in the direction of the arrow. 3 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. Return the release levers to their operating positions. The fusing unit is hot. Take care in removing paper. Fusing unit release levers ● ● 4 Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies.
MISFEED REMOVAL 3 Close the side cover by pressing the handle on the cover. ● The misfeed ( ) indicator will go out. Misfeed in the paper tray Before opening the paper tray, be sure to open the bypass tray, lift slightly on the side cover and slide the cover out until it stops, and then perform steps 1 to 3 described in the “A. Misfeed in the paper feed area” section. 2 Close the paper tray. 3 Lift slightly on the side cover and slide the cover out until it stops.
DEVELOPER REQUIRED When the indicator lights up, the developer should be replaced. DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN AUTHORIZED SHARP SERVICE TECHNICIAN. Contact your service center as soon as possible. MAINTENANCE REQUIRED STATUS INDICATORS When the indicator lights up, service by an authorized SHARP service technician is required. Contact your service center as soon as possible.
USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. List of user programs This copier has the following user programs. Program No. Program name Description User programs GENERAL INFORMATION 1 Auto clear time Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made.
USER PROGRAMS Setting the user programs 1 Press and hold the light ( ) key for more than 5 , , , seconds until all the alarm indicators ( , and ) blink and “– –” appears in the copy quantity display. 2 Enter a program number using the numeric keys. ● The selected program number will blink in the copy quantity display. ● If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. ● The program numbers are shown in the table below. ) key.
USER PROGRAMS 4 Select the desired parameter using the numeric keys. ● The entered parameter number will blink on the right side of the copy quantity display. ● The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min., press key 2. Program name Auto clear time Parameters 0 OFF 1 30 sec. 5 10 sec. Preheat mode 0 OFF 1 30 sec. Auto power shut-off timer *1 30 min. 2 60 min.
USER PROGRAMS Settings for auditing accounts Setting of user programs No. 10 to 15 varies with the program number. For settings of all programs, first follow steps 1 to 3 in “Setting the user programs” on page 47 to select a program. (1. Press the light ( ) key for more than 5 seconds. 2. Enter a program number (10 to 15) using the numeric keys. 3. Press the START key.) Then follow the appropriate instructions for the program. Program No.
USER PROGRAMS Program No. 12: Account number change Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “12E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 47. 1. Use the copy ratio display ( number to be changed. ● 2. Use the ) key to select the account key to advance through the account numbers. Press the START key.
USER PROGRAMS Program No. 14: Number of copies per account Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “14E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 47. 1. Use the copy ratio display ( number. ● 2.
USER PROGRAMS Program No. 15: Resetting account Program No. 15 is used to reset all accounts or to reset any desired individual account. When program No. 15 is entered, “0” will blink on the right side of the copy quantity display. ● If no account number has been registered, “15E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 47. 1. To reset an individual account, press the 0 key. To reset all accounts, press key 1. 2. Press the START key. 3.
POWER SAVE MODES The copier has two power save modes to reduce overall power consumption thereby reduce the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode. ● User programs The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. for preheat mode and 30 min. for auto power shut-off mode.
POWER SAVE MODES Setting the power save modes The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 47. ● The copier will enter the preheat mode first and then the auto power shutoff mode after a preset time has elapsed when no copier operation has been made.
USER MAINTENANCE Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Original table and platen cover Stains or dirt on the original table or platen cover will also be copied. Wipe the original table and platen cover with a soft, clean cloth. ● If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. ● Wipe the scanning window on the original table.
USER MAINTENANCE Transfer charger cleaning If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. Charger cleaner User maintenance GENERAL INFORMATION 1 2 Turn the power switch off. 3 Gently lift and pull out the paper tray and take the charger cleaner out by holding the tab. 4 Set the charger cleaner onto the transfer charger and gently slide the cleaner in the direction indicated by the arrow two or three times.
COPIER TROUBLE? Problem Solution ● Copier plugged in? Plug the copier into a grounded outlet. See page 8. ● Power switch ON? Turn the power switch ON. See page 14. Copies are too dark or too light. ● Copy density properly adjusted? See pages 14 and 26. Blank copies ● Is the original placed face up in the SPF or face down on the original table? Place the original face up in the SPF or face down on the original table. ● Paper too heavy? Use copy paper within the specified range. See page 60.
COPIER TROUBLE? Problem Copies are smudged or dirty. Solution ● Original table or document feeder cover dirty? Clean regularly. See page 55. ● Original smudged or blotchy? Use a clean original. ● Is the indicator on? Developer is required. Contact your SHARP service center as soon as possible. See page 45. ● Is the indicator on? Maintenance is required. Contact your SHARP service center as soon as possible. See page 45.
COPIER TROUBLE? Problem Solution ● Is blinking in the copy quantity display? A toner cartridge is not installed. Install a toner cartridge. If "CH" is blinking even if a cartridge is installed properly, contact your SHARP service center immediately. ● Is steadily lit in the copy quantity display? Side cover(s) is open. Close the front and side covers securely. ● Is the indicator blinking? The toner cartridge must be replaced. See page 38, TONER CARTRIDGE REPLACEMENT.
SUPPLIES Types and sizes of copy paper * Size Weight Capacity (21 lb. bond paper) Paper tray 5-1/2" x 8-1/2"* to 11" x 17" 15 lbs. to 21 lbs. 250 sheets Bypass tray Ordinary paper: 5-1/2" x 8-1/2" to 11" x 17" Envelopes: Commercial 10 (4-1/8" x 9-1/2") International DL (110 x 220 mm) International C5 (162 x 229 mm) 15 lbs. to 34 lbs.** (Ordinary paper) 100 sheets 5-1/2" x 8-1/2" copy paper can be used in the uppermost paper tray but cannot be used in other trays (in optional paper feed units).
SUPPLIES Genuine supplies statement Standard supplies for this copier that are to be replaced by the user are copy paper and toner cartridge. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package. Proper storage 1. 2.
SPECIFICATIONS Specifications GENERAL INFORMATION 62 Type Desktop Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. 11" x 17" Copy sizes Max. 11" x 17" Min. 5-1/2" x 8-1/2" Image loss: Max. 5/32" (4 mm) (leading and trailing edges) Max. 5/32" (4 mm) (along other edges in total) Copying speed (at 100% copy ratio) 16 copies/min. (8-1/2" x 11") 12 copies/min. (8-1/2" x 11"R) 10 copies/min. (8-1/2" x 14") 9 copies/min. (11" x 17") Continuous copy Max.
SPECIFICATIONS 23-15/64" (W) x 20-29/32" (D) (590 mm (W) x 531 mm (D)) Weight Approx. 70.6 lbs. (32 kg) Toner cartridge included Copier dimensions 23-15/64" (W) x 20-29/32" (D) x 18-33/64" (H) (590 mm (W) x 531 mm (D) x 470 mm (H)) Operating conditions Temperature: 59°F to 86°F (15°C to 30°C) Humidity: 20% to 85% Acoustic noise emission (measurement according to ISO 7779) Sound power level LWA Operating: 6.1 [B], Standby: 3.
MEMO GENERAL INFORMATION 64
OPTIONAL EQUIPMENT CONTENTS ● ● Page SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 250-SHEET PAPER FEED UNIT (AR-DE5)/ 2x250-SHEET PAPER FEED UNIT (AR-DE6) . . . . . . . . . . . . . . 67 ● Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 ● Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 ● Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYSTEM CONFIGURATION A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following. Facsimile expansion kit (AR-FX2)* Printer expansion kit (AR-PB8)* PS2 expansion kit (AR-PS1)* LCD panel kit (AR-PA1)* Job separator tray kit (AR-TR2)* Print server card (AR-NC3D)* * These options are not used for the copier operation.
250-SHEET PAPER FEED UNIT (AR-DE5) 2x250-SHEET PAPER FEED UNIT (AR-DE6) These paper feed units as options provide the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying. The AR-DE5 contains one 250-sheet paper tray and the AR-DE6 contains two 250-sheet paper trays.
250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( ) indicator and the red indicator which indicates the paper feed unit will blink. 1 Open the side cover of the paper feed unit and remove the misfed paper. ● 250-sheet paper feed unit (AR-DE5) 2x250-sheet paper feed unit (AR-DE6) OPTIONAL EQUIPMENT 68 Be sure to perform this step before pulling out the paper trays.
250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6) Specifications AR-DE5 Copy paper size 8-1/2" x 11" to 11" x 17" Paper weight 15 lbs. to 21 lbs. Paper capacity One paper tray with capacity for 250 sheets of 21 lb. bond paper Weight Approx. 10.4 lbs. (4.7 kg) Dimensions 23-15/64" (W) x 18-35/64" (D) x 3-15/32" (H) (590 mm (W) x 471 mm (D) x 88 mm (H)) Power supply Drawn from the copier AR-DE6 8-1/2" x 11" to 11" x 17" Paper weight 15 lbs. to 21 lbs.
INDEX 2 250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . . . 67 2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2x250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . 67 4 4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 A Auto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 46 Automatic exposure adjustment . . . . . . . . . . . . . . . . . .
INDEX R Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Replacement – toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 S Single pass feeder (SPF) . . . . . . . . . . . . . . . . . . . . . . . . Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications – copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date Issued: Nov. 1, 2000 MATERIAL SAFETY DATA SHEET MSDS No. F-00991 Section 1. Product Identification Product: AR-201NT/T/FT/ST (Black Toner) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3. Ingredients Ingredients Styrene-Acrylate copolymer Carbon black Iron oxide Metal Complex dye Section 4.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
Date Issued: Nov. 1, 2000 MATERIAL SAFETY DATA SHEET MSDS No. F-30991 Section 1. Product Identification Product AR-201ND/DV/SD (Black Developer) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3. Ingredients Ingredients Iron powder Styrene-Acrylate copolymer Carbon black Section 4.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
MEMO
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
AR-164 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.