LCD MONITOR TOUCH PEN UTILITY OPERATION MANUAL Applicable models (as of March 2014) PN-L703A/PN-L603A/PN-70TA3/PN-60TA3/PN-ZL01/PN-ZL02 (Available models differ according to region.) Version 1.
Contents Introduction.......................................................................3 System Requirements...................................................3 Setting up the PC (Full version)......................................4 Install.............................................................................4 Showing active pen information.....................................5 Active pen settings...........................................................6 How to configure settings..............
Introduction This software enables a touch pen of an applicable model to be used. The software is preinstalled in WHITEBOARD mode. (This version is referred to as the “lite version” in this manual.) To use a touch pen with a computer, this software must be installed on the computer. (This version is referred to as the “full version” in this manual.) The touch pen (3 button pen) that is included with an applicable model is referred to as “active pen” in this manual.
Setting up the PC (Full version) Install Caution • Connect the touch panel, and then install the touch panel settings tool. • Insert the touch pen adapter into the LCD monitor before installing the touch pen utility. • If an older version of the touch pen utility is installed, remove (uninstall) the old version before installing the touch pen utility. (See page 10.) • This can only be done by a user with administrator authority. 1. 2. 3. 4. 5. 6. Start your PC. Exit all applications that are running.
Showing active pen information The touch pen utility starts automatically. You can view information on the active pen that is being used. nFull version 1. Click the touch pen utility icon ( ) on the taskbar. nLite version Touch [Touch Pen] in the launcher of WHITEBOARD mode. • Touch pen information : Shows the registration number, the battery level and the signal strength of the active pen being used. • Touch pen settings : See page 6. • Operation settings : See page 9.
Active pen settings How to configure settings Settings that can be changed are as follows. • Registering/canceling an active pen: See page 7. • Advanced: See page 7. - Touch pen setting: See page 7. - Function buttons: See page 8. - Test Information: Shows the active pen function buttons, pen pressure levels, and other information. (For service technicians.) nFull version 1. Click the touch pen utility icon ( ) on the taskbar. 2. Click [Touch pen settings]. 3. Change the settings. (See page 7.
Active pen settings Registering/canceling an active pen To use the active pen provided with the PN-ZL02, you must register the active pen (pairing). You can also cancel the registration of an active pen. nRegistering an active pen See the operation manual for the LCD monitor. nCanceling the registration of an active pen 1. Click the active pen you want to cancel in the touch pen settings screen. 2. Click [Release]. Advanced 1.
Active pen settings nCustomize touch pen pressure You can adjust the pen pressure in the Pen Software. Touch pen pressure table setting You can manually adjust the touch pen pressure and stroke thickness. Preset The touch pen pressure table can be selected and set from the presets. Preset settings The set touch pen pressure table can be assigned a name and saved. (Up to 10.) In addition, saved presets can be deleted.
Operation settings Input mode Set the input mode for the touch panel. It is normally recommended that you use “Standard”. • Standard : Automatically switches between pen mode and handwriting mode. • HandWriting : Select this only when you want to use your finger or a pen other than an active pen, and will not be using the active pen function. • Pen : Only the active pen can be used. Your finger or a pen other than an active pen cannot be used.
Uninstall (Full version) Caution • This can only be done by a user with administrator authority. 1. Click the touch pen utility icon ( ) on the taskbar and click “Exit”. • If a confirmation window appears, click “Yes”. 2. Remove the touch pen adapter. 3. Select “Control Panel” from the “Start” menu. 4. Click “Uninstall a program”. • If you are using icon view (Classic View), double-click “Programs and Features”. 5. Select “SHARP Touch Pen” and click “Uninstall”. • Follow the on-screen instructions.
V1.