CE-AG06 DIGITAL CAMERA CARD DIGITALKAMERA-KARTE OPERATION MANUAL BEDIENUNGSANLEITUNG page • • • • • • • • Introduction ................................................ 2 Key Features ............................................. 3 Notice ........................................................ 4 Names and Functions of Parts .................. 6 Installing and Removing the Digital Camera Card . 7 Taking Pictures .......................................... 9 Specifications ................................
In U.S.A.: Declaration of Conformity Digital Camera Card: CE-AG06 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ENGLISH CONTENTS Thank you very much for choosing the SHARP digital camera card CE-AG06. Please read this operation manual carefully to use the product properly. After reading, keep the manual in a safe place for later reference. Disclaimer • Except as validated by the products liability law, we do not assume any responsibility for damages to your or third parties caused by improper handling of the product or any of its accessories or by their operational failures, as well as by their use.
Introduction This product (digital camera card CE-AG06) can be used as a digital camera when inserted in a CF card slot, as in the SL-5500. Software installed in the main unit allows you to transmit pictures taken with this product as email attachments. For more information, refer to the operation manual of the main unit.
Key Features • The CE-AG06, when inserted into the main unit, offers you a joy of photography instantly. Image sensor: CMOS Image sensor with 350,000 pixels Maximum image resolution: 480 × 640 dots (VGA) • Using the main unit zoom feature lets you zoom in on your subject to a magnification of about two. • The close-up feature keeps you as close to your subject as about 6 cm. • The pictures you took can be saved to the memory of the main unit or to an SD memory card in the JPEG format.
Notice When using this product, please fully observe these handling precautions to prevent failures and other troubles. • When carrying the main unit or leaving it out of service, remove the product from it and insert the included CF card slot Protection card in its place. Keep the product removed carefully to safeguard against undue pressure. • Do not swing or carry the main unit with this product inserted in it by holding the main unit or product alone.
unit. Avoid also applying undue force from the rotary lens mechanism. • Do not touch the lens with a pointed object or bare hands. The lens may be flawed or stained. If the lens gets dirty, lightly wipe it with a cotton swab or any other soft material. • Do not leave the product in a place exposed to direct sunlight, in a car, near a heater, or in any other place that may become hot. Such location can be a source of failure. • Avoid using or leaving the product in a dusty or damp place.
Names and Functions of Parts Focus dial Turn the dial to focus on your subject to shoot (see page 11). Lens Lens unit The lens unit rotates. Rotate it to aim at you subject to shoot (see page 10). Card unit Shutter release button Press to take a picture and save the picture data. 6 CE-AG06本文(E) Page 6 02.1.12, 1:03 PM Adobe PageMaker 6.
Installing and Removing the Digital Camera Card Installing the card in the main unit 1. Remove the Display protection cover from the main unit. 2. Turn the main unit on. 3. If a card is already inserted in the CF card slot of the main unit, remove it. • Refer to the operation manual of the main unit when removing cards. . Insert this product (CE-AG06) fully straight 4 into the CF card slot of the main unit. Caution Having this product inserted in a notebook computer or the like can result in failure.
Removing the card from the main unit 1. Exit all applications running on the main unit. 2. Tap the CF card icon ( ) in the lower right corner of the LCD screen to see a popup menu. Then, tap "Eject card" on this menu. • The CF card icon disappears. . With the main unit turned on, remove the 3 product from it by pulling it straight. 4. Insert the CF card slot Protection card into the CF card slot of the main unit. Caution • Do not remove the product from the main unit by holding its lens unit.
Taking Pictures Basic flow of photography 1. Insert the product into the main unit (see page 7). 2. Launch the Camera Application from the main unit (refer to the documentation that comes with the Camera Application). A digital camera screen (or the LCD screen in which your subject is imaged) is displayed. 3. Set the destination to which to save the picture data, the picture size (resolution) and other relevant picture characteristics from the main unit and check that the picture counter does not equal 0.
Adjusting the rotation and orientation of the lens unit (Figure A) Lens unit The lens unit rotates. Holding the main unit, aim the lens unit at your subject for adjustment. Caution Do not turn the lens unit past its range of rotation, which spans about 180° from the position shown in Figure A to that in Figure B. • Do not force the lens unit to rotate. • You can orient the lens unit at yourself to capture your self-portraits. (Figure B) 10 CE-AG06本文(E) Page 10 02.1.12, 1:03 PM Adobe PageMaker 6.
Adjusting the focus Tips on taking pictures Turn the focus dial to optimize the image of your subject appearing on the LCD screen of the main unit. • If you take a picture in a dark environment, its image may look coarse, but this is not a failure. • When you press the shutter release button, the image you shot stays still on the LCD screen for a while until its save is completed, when the screen is restored, allowing you take the next picture.
Dew condensation If this product is quickly moved from a cold place into a warm place, the temperature difference will cause dew to condense inside and outside the product. Generally, allow the product to stand for about 1 hour at the ambient temperature before use. Preventing blurry pictures Moving the main unit when you press the shutter release button to take a picture could give a blurry image to the picture. In picture taking in a dimly lit place, the shutter speed will slow down.
Customer care • To the main unit and the lens unit, lightly wipe with a clean, soft dry cloth, such as a cotton swab. • Never use organic solvents, such as thinner or benzine, and wet cloths for cleaning. Use of these materials may degenerate or discolor the main unit and the lens unit. • When leaving the product out of service for extended periods of time, remove it from the main unit and store it to protect the lens (see page 8).
Specifications Model Image sensor Lens Shutter speed Focus mode Focus range Exposure control White balance Monitor Picture storage Recording format Image resolution I/O interface Power Operating temperature and humidity Dimensions Weight Accessory CE-AG06 Product name Digital camera card 1/4-type primary color RGB filter CMOS Image sensor with 350,000 (effective 310,000) square pixels Monofocus lens F3.4 f=3.85 mm (equivalent to 40 mm on a 35 mm camera) Automatic (1/10 to 1/15,750 second) Manual Approx.
Troubleshooting If you are experiencing difficulties with the camera card, check the following table for possible solutions before requesting repair services: Problem Nothing appears on the LCD screen (the LCD screen looks black or green). Cause and solution • The product may not be connected properly. Check that it is fully inserted in the CF card slot of the main unit. • Check that the battery (rechargeable) loaded in the main unit are not weak or depleted.
Problem Picture is not clear. Cause and solution • Check that the lens is not dirty. If the lens gets dirty, clean it with a cotton swab or any other soft material. • Check that the focus is adjusted correctly. Turn the focus dial for adjustment (see page 11). • Haven’t you photograph any source of infrared emission? When a source of infrared emission is shot, its colors may not look right. • When you photograph a brightly shining object, horizontal lines will appear in the resultant picture.
MEMO 17 CE-AG06本文(E) Page 17 02.1.12, 1:03 PM Adobe PageMaker 6.
MEMO 18 CE-AG06本文(E) Page 18 02.1.12, 1:03 PM Adobe PageMaker 6.
DEUTSCH INHALT Wir danken Ihnen für den Kauf der SHARP Digitalkamera-Karte CE-AG06. Bitte lesen Sie diese Bedienungsanleitung aufmerksam durch, um das Produkt korrekt zu benutzen. Bewahren Sie die Bedienungsanleitung nach dem Lesen für späteres Nachschlagen an einem sicheren Platz auf.
Zur Beachtung Vorwort 2 Dieses Produkt (Digitalkamera-Karte CE-AG06) kann als Digitalkamera verwendet werden, wenn es in einen CF-Erweiterungssteckplatz, wie beim SL-5500, eingesetzt wird. Die im Hauptgerät installierte Software ermöglicht es Ihnen, die mit diesem Produkt aufgenommenen Bilder als EMail-Anhang zu versenden. Weitere Informationen dazu finden Sie in der Bedienungsanleitung des Hauptgerätes.
Hauptmerkmale Zur Beachtung • Sie brauchen das Produkt CE-AG06 nur in das Hauptgerät einzusetzen, und schon können Sie fotografieren. Bildsensor: CMOS-Bildsensor mit 350.000 Pixeln Maximale Bildauflösung: 480 × 640 Punkte (VGA) • Bei Verwendung der Zoomfunktion des Hauptgerätes können Sie Ihr Motiv bis auf das Zweifache vergrößern. • Bei Verwendung der Makro-Funktion können Sie bis auf etwa 6 cm an das Motiv herangehen.
• Entfernen Sie den Display-Schutz vom Hauptgerät, bevor Sie das Produkt in das Hauptgerät einsetzen. • Richten Sie das Objektiv nicht auf die Sonne. Es kann sonst zu Farbverzerrungen oder Einbrenneffekten kommen. • Unterlassen Sie das Entfernen des Produktes oder das Verstellen des Batteriewechselschalters am Hauptgerät, während ein Bild gespeichert wird. Durch diese Handlungen können die Bilddaten verfälscht werden.
Ort. Solche Orte können die Ursache für einen Ausfall sein. • Bewahren Sie das Produkt nicht in einer Gesäßtasche Ihrer Hose oder in einer Brusttasche auf. Übermäßige Druckausübung auf das Produkt kann Beschädigung zur Folge haben. • Das Produkt ist nicht wasserdicht konstruiert. Ve r m e i d e n S i e d i e B e n u t z u n g o d e r Aufbewahrung des Produktes an Orten, an denen es mit Wasser oder anderen Flüssigkeiten bespritzt werden kann.
Bezeichnung und Funktion der Teile Fokussierring Drehen Sie diesen Ring, um das aufzunehmende Motiv scharf einzustellen (siehe Seite 11). Objektiv Objektivteil Der Objektivteil ist drehbar. Drehen Sie diesen Teil, um das Objektiv auf das Aufnahmeobjekt zu richten (siehe Seite 10). Kartenteil Auslöser Drücken Sie den Auslöser, um ein Bild aufzunehmen und die Bilddaten zu speichern. 6 CE-AG06本文(G) Page 6 02.1.12, 1:04 PM Adobe PageMaker 6.
Einsetzen und Herausnehmen der Digitalkamera-Karte Einsetzen der Karte in das Hauptgerät 1. Entfernen Sie den Display-Schutz vom Hauptgerät. 2. Schalten Sie das Hauptgerät ein. 3. Falls bereits eine Karte in den CFErweiterungssteckplatz des Hauptgerätes eingesetzt ist, nehmen Sie diese heraus. • Informationen zum Herausnehmen von Karten finden Sie in der Bedienungsanleitung des Hauptgerätes. 4.
Herausnehmen der Karte aus dem Hauptgerät 1. Beenden Sie alle auf dem Hauptgerät laufenden Anwendungen. 2. Tippen Sie auf das Symbol der CF-Karte ( ) in der unteren rechten Ecke des LCDBildschirms, um ein Kontextmenü aufzurufen. Tippen Sie dann auf "Karte auswerfen" in diesem Menü. • Das Symbol der CF-Karte verschwindet. 3. Ziehen Sie das Produkt bei eingeschaltetem Hauptgerät gerade heraus. . 4 Schieben Sie die CF-Platzhalterkarte in den CF-Erweiterungssteckplatz des Hauptgerätes ein.
Fotografieren Grundlegender Ablauf der Aufnahme 1. Setzen Sie das Produkt in das Hauptgerät ein (siehe Seite 7). 2. Starten Sie die Anwendung "Kamera" im Hauptgerät (Schlagen Sie in der mit der Anwendung "Kamera" gelieferten Dokumentation nach). Der Digitalkamera-Bildschirm (Zustand, in dem das Motiv auf dem LCD-Bildschirm des Hauptgerätes abgebildet wird) erscheint. 3.
Drehen und Ausrichten des Objektivteils (Abbildung A) Objektivteil Der Objektivteil ist drehbar. Halten Sie das Hauptgerät, und richten Sie den Objektivteil auf das Motiv aus. Vorsicht Drehen Sie den Objektivteil nicht über seinen Drehbereich hinaus, der von der in Abbildung A gezeigten Position bis zu der in Abbildung B gezeigten Position etwa 180° umfasst. • Drehen Sie den Objektivteil nicht gewaltsam. • Sie können den Objektivteil auf sich selbst richten, um sich in Selbstporträts zu fotografieren.
Scharfeinstellung Tipps zum Fotografieren Drehen Sie den Fokussierring, um das auf dem LCD-Bildschirm des Hauptgerätes angezeigte Motiv scharf einzustellen. • Wenn Sie in dunkler Umgebung fotografieren, kann das Bild grob erscheinen, was aber keine Störung darstellt. • Wenn Sie den Auslöser drücken, bleibt das aufgenommene Bild noch eine Weile auf dem L C D - B i l d s c h i r m s i c h t b a r, b i s d e r Speichervorgang beendet ist.
• Besonders helle Teile eines Motivs, wie z.B. der Glühfaden einer Glühlampe, können dunkel erscheinen, was jedoch keine Störung darstellt. • Wenn Sie ein bewegtes Motiv aufnehmen, kann seine Form verzerrt erscheinen, was jedoch keine Störung darstellt. Kondensation Wird dieses Produkt schnell von einem kalten zu einem warmen Ort gebracht, bewirkt der Te m p e r a t u r u n t e r s c h i e d d i e B i l d u n g v o n Kondensation auf der Innen- und Außenseite des Produktes.
Pflege • Wischen Sie Hauptgerät und Objektivteil zum Reinigen leicht mit einem sauberen, weichen und trockenen Tuch oder Wattebausch ab. • Verwenden Sie niemals organische Lösungsmittel, wie Verdünner oder Benzol, oder ein nasses Tuch zum Reinigen. Die Verwendung solcher Materialien kann zu einer Verschlechterung oder Verfärbung des Hauptgerätes und des Objektivteils führen.
Technische Daten Modell Bildsensor CE-AG06 Produktbezeichnung Digitalkamera-Karte 1/4-Zoll-Primärfarben-RGB-Filter-CMOS-Bildsensor mit 350.000 (effektiv 310.000) quadratischen Pixeln Objektiv Monofokus-Objektiv F3,4 f=3,85 mm (entspricht 40 mm bei einer 35-mm-Kamera) Verschlusszeit Automatisch (1/10 bis 1/15.750 Sekunde) Scharfeinstellung Manuell Scharfeinstellbereich ca.
Fehlersuche Falls Sie Schwierigkeiten mit der Kamerakarte haben, suchen Sie in der folgenden Tabelle nach möglichen Lösungen, bevor Sie den Kundendienst anrufen: Problem Nichts erscheint auf dem LCD-Bildschirm (der LCD-Bildschirm ist schwarz oder grün). Ursachen und Lösungen • Das Produkt ist möglicherweise nicht richtig angeschlossen. Prüfen Sie nach, ob es vollständig in den CF-Erweiterungssteckplatz des Hauptgerätes eingeführt ist.
Problem Ursachen und Lösungen Das Bild ist unscharf. • Prüfen Sie nach, ob das Objektiv verschmutzt ist. Falls das Objektiv schmutzig wird, wischen Sie es leicht mit einem Wattebausch oder einem anderen weichen Material ab. • Prüfen Sie nach, ob die Schärfe korrekt eingestellt ist. Drehen Sie den Fokussierring für die Scharfeinstellung (siehe Seite 11). • Haben Sie eine Infrarotlichtquelle aufgenommen? Wenn eine Infrarotlichtquelle aufgenommen wird, können die Farben verfälscht werden.
17 CE-AG06本文(G) Page 17 02.1.12, 1:04 PM Adobe PageMaker 6.
In Europe: This equipment complies with the requirements of Directive 89/336/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinie 89/336/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans la directive 89/336/CEE modifiée par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijn 89/336/EEG, gewijzigd door 93/68/EEG. Dette udstyr overholder kravene i direktiv nr. 89/336/EEC med tillæg nr. 93/68/EEC.
In U.S.A.: LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
SHARP CORPORATION PRINTED IN JAPAN / GEDRUCKT IN JAPAN 02A-032LP CE-AG06表紙 Page 5 02.1.12, 1:02 PM Adobe PageMaker 6.