User manual
Table Of Contents
- TABLE OF CONTENTS
- ABOUT THIS MANUAL
- BASIC PROCEDURE FOR MAKING COPIES
- BASE SCREEN OF COPY MODE
- COPYING SEQUENCE
- MAKING COPIES
- AUTOMATIC 2-SIDED COPYING
- COPY COLOUR MODES
- CHANGING THE EXPOSURE AND EXPOSURE MODE
- REDUCTION/ENLARGEMENT/ZOOM
- ORIGINAL SIZES
- OUTPUT
- MAKING COPIES USING THE BYPASS TRAY (Copying on special papers)
- INTERRUPTING A COPY RUN (Interrupt copy)
- JOB STATUS SCREEN
- CONVENIENT COPY FUNCTIONS
- SPECIAL MODES
- ADDING MARGINS (Margin Shift)
- ERASING PERIPHERAL SHADOWS (Erase)
- COPYING EACH FACING PAGE OF A BOUND DOCUMENT (Dual Page Copy)
- MAKING COPIES IN PAMPHLET FORMAT (Pamphlet Copy)
- COPYING A LARGE NUMBER OF ORIGINALS AT ONCE (Job Build)
- USING TWO MACHINES TO COPY A LARGE NUMBER OF ORIGINALS (Tandem Copy)
- USING A DIFFERENT PAPER TYPE FOR COVERS (Covers/Inserts)
- ADDING INSERTS WHEN COPYING ON TRANSPARENCY FILM (Transparency Inserts)
- COPYING MULTIPLE PAGES ONTO ONE SHEET OF PAPER (Multi Shot)
- COPYING A PAMPHLET (Book Copy)
- COPYING CAPTIONS ONTO TAB PAPER (Tab Copy)
- COPYING BOTH SIDES OF A CARD ON ONE SHEET OF PAPER (Card Shot)
- PRINTING THE DATE AND A STAMP ON COPIES (Stamp)
- CHECKING THE STAMP LAYOUT (Layout)
- REPEATING PHOTOS ON A COPY (Photo Repeat)
- CREATING A LARGE POSTER (Multi-Page Enlargement)
- REVERSING THE IMAGE (Mirror Image)
- COPYING A3 (11" x 17") SIZE ORIGINAL WITHOUT CUTTING OFF THE EDGES (A3 (11x17) Full Bleed)
- COPYING IN THE CENTRE OF THE PAPER (Centring)
- ADJUSTING RED/GREEN/BLUE IN COPIES (RGB Adjust)
- ADJUSTING THE SHARPNESS OF AN IMAGE (Sharpness)
- WHITENING FAINT COLOURS IN COPIES (Suppress Background)
- ADJUSTING THE COLOUR (Colour Balance)
- ADJUSTING THE BRIGHTNESS OF A COPY (Brightness)
- ADJUSTING THE INTENSITY OF A COPY (Intensity)
- CHECKING COPIES BEFORE PRINTING (Proof Copy)
- COPYING ORIGINALS OF DIFFERENT SIZES (Mixed Size Original)
- COPYING THIN ORIGINALS (Slow Scan Mode)
- STORING COPY OPERATIONS (Job Programs)
- APPENDIX
158
STORING A JOB PROGRAM
The procedure for storing copy settings in a job program is explained below.
1
Press the [PROGRAM] key ( ).
2
Touch the [Store/Delete] tab.
3
Touch a numeric key that is not
highlighted.
Numeric keys in which job programs are already stored are
highlighted.
If a highlighted numeric key is touched, the following screen appears.
The [Store] key can be touched to delete the stored settings and store new settings.
When "Disabling Deletion of Job Programs" is enabled in the system settings (administrator), this function cannot be used.
4
Select the copy settings that you wish to
store in the job program and touch the
[OK] key.
To assign a name to the program, touch the [Program Name]
key. A text entry screen will appear.
Up to 10 characters can be entered for the name.
To enter text, see "6. ENTERING TEXT" in the User's Guide.
When you have finished entering the name, touch the [OK] key.
The number of copies cannot be stored.
LOGOUT
Job Programs
Press program number.
5 6 7
3
8
41 2
1/6
Exit
Store/Delete
Recall
Job Programs
Press program number.
1 2
5 6 7
3
8
4
1/6
Recall
Exit
Store/Delete
A job program has been already stored
in this location.
Cancel Delete Store
To store, make selections and press
[OK], to delete, press [Cancel].
2-Sided Copy
Original
Output
Program Name
Full Colour
Colour Mode
2.
3.
4.
1.
Auto
Exposure
100%
Copy Ratio
Job Detail
Settings
A4
Cancel OK
A4
A4R
B4
A3
A4
A4
Plain