User manual
Table Of Contents
- TABLE OF CONTENTS
- ABOUT THIS MANUAL
- BASIC PROCEDURE FOR MAKING COPIES
- BASE SCREEN OF COPY MODE
- COPYING SEQUENCE
- MAKING COPIES
- AUTOMATIC 2-SIDED COPYING
- COPY COLOUR MODES
- CHANGING THE EXPOSURE AND EXPOSURE MODE
- REDUCTION/ENLARGEMENT/ZOOM
- ORIGINAL SIZES
- OUTPUT
- MAKING COPIES USING THE BYPASS TRAY (Copying on special papers)
- INTERRUPTING A COPY RUN (Interrupt copy)
- JOB STATUS SCREEN
- CONVENIENT COPY FUNCTIONS
- SPECIAL MODES
- ADDING MARGINS (Margin Shift)
- ERASING PERIPHERAL SHADOWS (Erase)
- COPYING EACH FACING PAGE OF A BOUND DOCUMENT (Dual Page Copy)
- MAKING COPIES IN PAMPHLET FORMAT (Pamphlet Copy)
- COPYING A LARGE NUMBER OF ORIGINALS AT ONCE (Job Build)
- USING TWO MACHINES TO COPY A LARGE NUMBER OF ORIGINALS (Tandem Copy)
- USING A DIFFERENT PAPER TYPE FOR COVERS (Covers/Inserts)
- ADDING INSERTS WHEN COPYING ON TRANSPARENCY FILM (Transparency Inserts)
- COPYING MULTIPLE PAGES ONTO ONE SHEET OF PAPER (Multi Shot)
- COPYING A PAMPHLET (Book Copy)
- COPYING CAPTIONS ONTO TAB PAPER (Tab Copy)
- COPYING BOTH SIDES OF A CARD ON ONE SHEET OF PAPER (Card Shot)
- PRINTING THE DATE AND A STAMP ON COPIES (Stamp)
- CHECKING THE STAMP LAYOUT (Layout)
- REPEATING PHOTOS ON A COPY (Photo Repeat)
- CREATING A LARGE POSTER (Multi-Page Enlargement)
- REVERSING THE IMAGE (Mirror Image)
- COPYING A3 (11" x 17") SIZE ORIGINAL WITHOUT CUTTING OFF THE EDGES (A3 (11x17) Full Bleed)
- COPYING IN THE CENTRE OF THE PAPER (Centring)
- ADJUSTING RED/GREEN/BLUE IN COPIES (RGB Adjust)
- ADJUSTING THE SHARPNESS OF AN IMAGE (Sharpness)
- WHITENING FAINT COLOURS IN COPIES (Suppress Background)
- ADJUSTING THE COLOUR (Colour Balance)
- ADJUSTING THE BRIGHTNESS OF A COPY (Brightness)
- ADJUSTING THE INTENSITY OF A COPY (Intensity)
- CHECKING COPIES BEFORE PRINTING (Proof Copy)
- COPYING ORIGINALS OF DIFFERENT SIZES (Mixed Size Original)
- COPYING THIN ORIGINALS (Slow Scan Mode)
- STORING COPY OPERATIONS (Job Programs)
- APPENDIX
68
11
Press the [COLOUR START] key
( ) or the [BLACK & WHITE
START] key ( ).
Copying will begin.
• If the originals were placed in the document feeder tray, the
originals are copied.
• If you are using the document glass, copy each page one
page at a time. If you are using the sort function or other
function that requires all originals to be scanned before the
copies are printed, you must use the same [START] key that
you used to scan the first original to scan each of the
remaining originals.
To cancel scanning of the original and copying...
Press the [STOP] key ( ).
• To make pamphlet copies of a book or other bound original, use the book copy function.
• When the pamphlet copy function is selected, 2-sided copying mode is automatically selected. When settings are selected
that prevent 2-sided copying, the pamphlet copy function cannot be used.
• Scan the originals in order from the first page to the last page. The order of copying will be automatically adjusted by the
machine. Four original pages will be copied onto each sheet of paper. Blank pages may be automatically produced at the
end depending on the number of original pages.
• When a saddle stitch finisher is installed, saddle stitch can be used. When pamphlet copy is used in combination with the
saddle stitch function and the number of originals is greater than the number of sheets that can be stapled, a message will
appear showing the [Cancel] key, the [Continue] key, and the [Divide] key. To cancel the job, touch the [Cancel] key. To
make pamphlet copies without stapling, touch the [Continue] key. To divide the pages into sets that can be stapled, touch
the [Divide] key.
If you selected settings for adding a cover, it will not be possible to select "Divide". You can either continue pamphlet
copying without stapling, or cancel the job.
To cancel pamphlet copy...
Touch the [Cancel] key in the screen of step 4.
System Settings (Administrator): Automatic Saddle Stitch
When a saddle stitch finisher is installed, this setting can be enabled to have saddle stitch take place automatically when the
pamphlet copy function is selected.
or