Service manual

ManualsBrandsSharp ManualsHome AudioCP-C602

CD-C602,CP-C602

– 1 –

CD-C602

CP-C602

• In the interests of user-safety the set should be restored to its

original condition and only parts identical to those specified be

used.

SERVICE MANUAL

SHARP CORPORATION

No. S1903CDC602//

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

CONTENTS

Page

IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)....................................................................................................... 2

SPECIFICATIONS ............................................................................................................................................................. 2

NAMES OF PARTS ........................................................................................................................................................... 3

QUICK GUIDE ................................................................................................................................................................... 5

DISASSEMBLY .................................................................................................................................................................. 6

REMOVING AND REINSTALLING THE MAIN PARTS ..................................................................................................... 8

ADJUSTMENT ................................................................................................................................................................... 9

NOTES ON SCHEMATIC DIAGRAM .............................................................................................................................. 11

TYPE OF TRANSISTER .................................................................................................................................................. 11

WAVEFORMS OF CD CIRCUIT ...................................................................................................................................... 12

BLOCK DIAGRAM ........................................................................................................................................................... 13

SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD ..............................................................................................16

VOLTAGE ........................................................................................................................................................................ 28

TROUBLESHOOTING ..................................................................................................................................................... 29

FUNCTION TABLE OF IC................................................................................................................................................ 33

LCD SEGMENT ................................................................................................................................................................38

PARTS GUIDE/EXPLODED VIEW

PACKING OF THE SET (FOR U.S.A. ONLY)

CD-C602 mini component system consisting of

CD-C602 mini component system, CP-C602 and rear

(GBOXS0020AWM1) speaker system.

Summary of content (52 pages)

PAGE 1
CD-C602,CP-C602 SERVICE MANUAL No. S1903CDC602// CD-C602 CP-C602 CD-C602 mini component system consisting of CD-C602 mini component system, CP-C602 and rear (GBOXS0020AWM1) speaker system. • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS Page IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)....................................................................................................... 2 SPECIFICATIONS ....
PAGE 2
CD-C602,CP-C602 FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY) BEFORE RETURNING THE AUDIO PRODUCT (Fire & Shock Hazard) Before returning the audio product to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the audio product. 2.
PAGE 3
CD-C602,CP-C602 CD-C602 NAMES OF PARTS 1 ■ Front panel 11. Disc Tray 12. 13. 14. 15. 16. 17. 18. 19.
PAGE 4
CD-C602,CP-C602 ■ Speaker section 1 GBOXS0020AWM1 ● Rear speaker 11. 12. 2 Woofer Speaker Wire CP-C602 ● Front speaker 13. 14. 15. Woofer Bass Reflex Duct Speaker Wire 3 4 5 1 CD-C602 ■ Remote control 11. 12. 13. 3 14. 3 15. 16. 17. 18. 19. 10. 11. 12. 13.
PAGE 5
CD-C602,CP-C602 QUICK GUIDE MINI COMPONENT SYSTEM Quick-Guide Guía rápida CD-C602 Turning the power on and off Conexión y desconexión de la alimentación Preparation for use Preparación para su uso (Left) (Izquierdo) Remote control Control remoto Remote Sensor Sensor remote (Right) (Derecho) POWER (Left) (Izquierdo) (Right) (Derecho) Red Rojo Black Negro FRONT SPEAKERS REAR SPEAKERS 15 Red Rojo Black Negro 8" - 20' (0.
PAGE 6
CD-C602,CP-C602 DISASSEMBLY CD-C602 Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape and compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit.
PAGE 7
CD-C602,CP-C602 Shift Lever Display PWB Hook (E2)x2 (E1)x8 ø3x10mm PWB Spacer (L1) x1 ø2.6 x10mm Front Panel (E1)x1 ø3x10mm (E3)x5 (K1) x4 ø3 x12mm CD Changer Mechanism PWB Spacer CD Player Base (E1)x1 ø3x10mm Hook (F2)x1 (E3)x1 Main PWB Hook (F2)x4 (F1)x2 ø3x10mm Figure 7-1 Be careful when installing the CD changer mechanism. Install the CD changer mechanism on the CD player base after the shift lever has been set in the highest position.
PAGE 8
CD-C602,CP-C602 REMOVING AND REINSTALLING THE MAIN PARTS CD MECHANISM SECTION Perform steps 1, 2, 3, and 8 ~ 11 of the disassembly method to remove the CD mechanism. How to remove the turntable up/down/loading motor (See Fig. 8-1) Turntable Up/Down/ Loading Motor 1. Remove the screws (A1) x 2 pcs., to remove the turntable up/down/loading motor. Motor PWB (A1) x2 ø2.6 x5mm Figure 8-1 How to remove the pickup (See Fig. 8-2) (B1) x2 ø2.6 x6mm 1. Remove the screws (B1) x 2 pcs.
PAGE 9
CD-C602,CP-C602 ADJUSTMENT MECHANISM SECTION TUNER SECTION • Driving Force Check Torque Meter fL: Low-range frequency fH: High-renge frequency • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated Specified Value Play: TW-2412 Tape 1: Over 100 g Tape 2: Over 50 g Test Stage Frequency Frequency Display IF 450 kHz 1,720 kHz Band Coverage — 530 kHz (fL): T333 *2 1.1 ± 0.
PAGE 10
CD-C602,CP-C602 CD SECTION CD TEST MODE Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary to readjust it. Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted. IL is not performed. • Automatic adjustment item 1. Focus offset (Fig. 10-1) 2. Tracking offset (Fig. 10-2) 3. E/F balance (tracking error balance) (Fig. 10-3) 4. RF level AGC function (HF level: constant) 5.
PAGE 11
CD-C602,CP-C602 NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means micro-micro-farad and the unit of the capacitor without such a symbol is microfarad.
PAGE 12
CD-C602,CP-C602 WAVEFORMS OF CD CIRCUIT STOP FOCUS 1 PLAY SERCH 6 1 5ms 0.50 V IC1 20 FE 7 1 8 1 12 5ms 5.0 V IC1 54 DRF 9 1 3 0.5ms 10.0 V IC1 33 0.5ms 10.0 V IC1 32 0.5ms 0.50 V IC1 14 0.5ms 1.00 V IC1 7 JP+ JP- JP TE 1 CUE 3 1 0.5ms 1.00 V IC1 41 HF PLAY 10 1 4 1 0.5ms 5.0 V IC1 4 HFL 5 1 0.5ms 5.0 V IC1 36 TES 3 1 0.5ms 1.00 V IC1 41 HF 4 1 0.5ms 5.0 V IC1 4 HFL 5 1 0.5ms 5.0 V IC1 36 TES 6 1 50ms 10.0 V IC1 33 JP+ NORMAL DISC TN0=01 20ms 1.
PAGE 13
CD-C602,CP-C602 TO MAIN/ POWER SECTION CHANGER MECHANISM SW1 SW2 SW3 SOLM2 OPEN/ MECHA DISC SOLENOID CLOSE UP NUMBER M - + 7 Q93 D81 37 38 39 40 36 41 LVDD RVDD /RES 36 LVDD 23 VDD +B 4.3V 58 +B 5V 32 DRF 54 SL+, SL–, DRF 50 49 44 43 40 SW4 PICKUP IN +5V ~ 20 61 ~ JP4M 1 9 10 12 JP- DEF1 EFMO EFMIN CLV+ 45 XIN XL1 16.
PAGE 14
CD-C602,CP-C602 IC301 TA7358AP FM FRONT END +B5 AM IF 3 FM +B 17 7 16 DET OUT 1 2 3 21 FM +B ST IND AM AM AM 22 23 24 AM +B FM OSC. FM IF FM RF 20 FM DET FM IF DET. /FM MPX. /AM IF 8 6 AM OSC L303 T301 AM RF IN VD302 L302 5 AM IF IC351 LA1805 TUN IND VD301 15 CNP301 FM/AM ANTNNA TERMINAL AM ANT. Q352 FM +B 11 L OUT L-CH 9 R-CH 10 R OUT VCO 13 VR351 VCO AM OSC.
PAGE 15
CD-C602,CP-C602 LCD701 LCD DISPLAY COM 0 ~ COM 3 25 ~ 22 S0 ~ S20 21 ~ 1 LCD BIAS 25 BIAS 29 KI0 26 VLC0 21 ~ 1 ~ 9 69 ~ 80 24 COM 0 ~ COM 3 COM OUT ~ ~ KEY MATRIX SEG0 ~ SEG20 SEG OUT 32 KI3 SW701 ~ SW712 SW714 ~ SW716 RESET RESET 68 Q701 KEY IN ~ ~ 34 KO0 37 KO3 DO DI CE CL POWER FAIL DETECTOR IC701 IX0217AW SYSTEM MICROCOMPUTER 63 65 66 64 D703 Q702 Q703 SYSTEM STOP 39 +B6 DSP RST POWER VDD(+5V) 40 41 43 51 52 54 T1/T2 POWER CONT.
PAGE 16
CD-C602,CP-C602 R1 1K +B TR+ 2 TR+ FO+ 3 FO– 4 FO+ 7 C37 220/6.3 C38 0.01 R29 1K R15 47K R41 4.7K CL CLK DEF DAT R16 1.5K SLOF – – VREF C33 0.001 RFSM C30 2.2P 41 CV+ 40 CV– SLOF 39 HFL 37 TES 36 TOFF TGL JP+ 35 SL+ JP– – SL– REF SLD SLEO SPO C34 0.033 (ML) RFS– 42 + – – + R23 1.2K R19 39K + – LATOH JP+ JPCLO OR R38 33K R36 47K R37 47K R33 5.6K C32 27P R34 1K R32 56K R35 C31 470 0.0027 L HF TP1 38 34 33 29 30 31 32 C19 47/25 R22 6.
PAGE 17
CD-C602,CP-C602 MAIN PWB-A1(1/4) 1K 1K 1K +B C57 100P R60 1K C22 0.01 C55 100P CD SIGNAL C54 100P R45 R46 R47 C56 100P +B EFLG 48 SBSY 47 NC SUB-CODE 1 DEF1 2 TA1 CLV DIGITAL SERVO V/P HLF C53 220P DAC 1BIT N.C. 34 TEST4 33 EXTERNAL OUTPUT SERVO TES COMMAND TOFF 16 CLV- 1K R86 CD-LD M– R97 2.2K R98 10K 4 5 6 +B L1 0.82µH +4.3V D81 1SS133 15 D_GND R96 10K Q91 KTA1271 Y SOLENOID 0V DRIVER +5V (SERVO) TO MAIN/ POWER SECTION P18 1-F 16 AUDIO GND 11.
PAGE 18
CD-C602,CP-C602 C443 0.68/50 8 7 6 5 4 3 2 NC NC NC NC NC NC NC NC L SELO NC 18 NC LIN VIN 2 62 20 NC B LTEST 59 23 CL 25 CE VDD 57 Vref 56 RVR OUT 55 26 VSS 27 AVSS RTEST 54 28 R1 RVR IN 53 RF1C3 NC NC NC NC NC NC NC RVref 50 NC RT IN R SELO NC 32 R3 RF1C2 RIN VIN 2 51 RF1C1 RT OUT 52 30 R2 RIN VIN 1 29 NC 31 NC C 49 13 CD_L CD_A_GND 15 C442 180P C440 22/16 CD_R +5V(µCOM) CD +B C436 0.
PAGE 19
CD-C602,CP-C602 MAIN PWB-A1(2/4) FM SIGNAL 64 ef 63 C463 2 62 PLAYBACK SIGNAL C459 0.0027 C461 100/10 LFS RECORD SIGNAL 100P CD SIGNAL UT 61 N 60 C465 10/50 R601 10K N 53 UT 52 R605 120 C471 0.022 R603 C601 3.3K 0.001 R604 C602 3.3K 0.001 C460 0.0027 C606 220/25 C462 100/10 RFS – 62 20K 9 20K 11 4 ef 50 C604 100/10 R606 120 10 L 7 C603 100/10 C464 100P 2 51 + 6 1 62 13 – + 3 R 2 C609 470/16 C611 0.1(ML) R607 3.3 R609 1.2K C466 10/50 R608 3.
PAGE 20
CD-C602,CP-C602 MAIN PWB-A1(3/4) CNP201 2 2 1 1 R228 68K C201 0.001 3 C202 0.001 R229 33K R216 56 R207 1K R-CH R218 100K Q201~Q206:SWITCHING R223 3.9K R226 5.6K Q205 KTC3199 GR R203 6.8K R214 1K 1 2 C212 330P 2 2 R236 560 7 8 + IC201 AN7345K HIGH=T2 PLAYBACK AN + 1 0V 0.7V 0V R204 6.8K 0V R201 10K Q204 2SC2389 SE 0.7V E R215 1K 23 C213 330P 112K 22 21 R210 10K 0V C203 180P – 24 0V 0V R205 3.3K 0V 20 C221 1/50 C211 330P C217 0.033 C219 (ML) 560P R225 5.
PAGE 21
CD-C602,CP-C602 R230 22K 24 RECL R259 100K 25 PLAYL 0V Q210 KTC3199 GR 0V 0V R245 10K R249 0V 10K R266 100K R236 560 C235 0.0033 D205 1SS133 C240 22/16 C241 100/10 9 GND(A) GND(D) R254 10K R247 10K R251 6.8K 15 14 13 Nor/ RIPPLE VCC CrO2 Q211 KTC3199 GR SWITCHING +B +B 56K +B R256 470 R248 10K +B R252 100K R250 47K HIGH=CHROME 56K 17 ALC ALC 10 11 GND 12 C238 1/50 C239 0.082 (ML) 16 T1/T2 C242 0.0039 (ML) + – C230 22/16 C236 0.0033 R237 560 30 7.
PAGE 22
CD-C602,CP-C602 A 7 C322 15P (CH) L302 R313 33K R312 22 R316 47 C332 0.001 C328 10/50 1 VD302 SVC211C 3 CF302 10.7MH R317 10K 2 R320 820 C321 0.022 FM IF +B FM BAND COVERAGE fL C320 0.001 C319 0.022 C323 18P R319 4.7K + R318 680 C327 100P R315 47K 2.11V D331 1SS133 C C316 0.0047 3 R314 10 FM OSC T301 FM IF 1 2 9 8 C326 0.022 6 VD301 SVC211C FM RF C313 0.0047 FM 1 GND 2 AM 3 C314 4.7P(UJ) D303 1SS133 CNP301 AM LOOP ANTENNA 4 5 C317 4.7P C318 0.
PAGE 23
CD-C602,CP-C602 AM IF CF351 1 3 T351 +B 15 C360 3.3/50 TP302 C363 1/50 14 TP303 13 R357 1.2K C359 3.3/50 R353 1.5K VR351 6.8K(B) VCO FM DET C356 0.0022 C354 220/10 12 11 NC 2.7K R376 3.3K C374 1/50 FM-M/ST 18 17 7.58V C362 3.3/50 T352 16 DET OUT 20 19 R351 3.9K 24 23 22 21 10 R359 10K 3 Q352 KRA109 M SWITCHING 7V 2 VCO 9 1 5.5V AM/FM 8 L-CH 7 TUN IND 6 GND AM IF 5 IC351 LA1805 FM IF DET./FM MPX./AM IF R352 C357 33K 0.
PAGE 24
CD-C602,CP-C602 TO MAIN/POWER SECTION P18 1-E 30 34 +B GND (µCOM) +5V (µCOM) 15 POWER_CONT 29 33 T2 PLAY T1 PLAY 32 REC 23 22 DO DI CE DISPLAY PWB-A2 21 CL 20 A TO DECK SECTION P21 12-D TO DECK SECTION P21 12-G T1/T2 TO MAIN/POWER TUNER SECTION P18 3-H, P23 12-G 1K 1K 1K 1K 6.8K B R742 4.7K R764 1K PU IN DISC NO REC WRQ C709 0.01 C717 0.022 REMOTE SENSOR RX701 3 +B +B R760 100K C707 0.
PAGE 25
CD-C602,CP-C602 SW3 DISC NUMBER SW607 TAPE1 RECORD CNS5 2 1 2 1 SW605 TAPE1 MAIN SW606 TAPE2 MAIN M601 TAPE MOTOR A - SW2 MECHA UP 8 7 6 5 4 3 2 1 TO MAIN PWB CNP203 P27 7 - A M3 TURNTABLE UP/DOWN/ LOADING MOTOR CNS4 TO MAIN PWB CNP4 P27 8 - H 6 - GY VL BL GR YL OR RD BR SOLM2 SOLENOID BIM5 B OR BR WH GY WH GY WH GY WH RD 10 9 8 7 6 5 4 3 2 1 + COLOR TABLE 1 BR TRAY MOTOR PWB-C PT901 POWER TRANSFOMER PICKUP UNIT C 1 + CNS203 SW1 OPEN/CLOSE BROWN RD(R) RED OR ORANGE YL Y
PAGE 26
CD-C602,CP-C602 FROM POWER TRANSFORMER P25 6-D FROM POWER TRANSFORMER P25 3-D CNS902 CNS901 M 1 IC921 1 2 3 5 10 C445 35 30 33 32 25 15 R450 R245 R240 C222 R448 40 IC431 C440 C58 20 C436 16 17 11 R C41 C34 R36 R357 C38 C40 R42 R8 R11 C364 R2 R3 C3 C362 1 Q1 R358 R353 MAIN PWB-A1 2 3 4 Figure 26 WIRING SIDE OF P.W.
PAGE 27
CD-C602,CP-C602 FROM TAPE MECHANISM P25 4-B FROM TAPE MECHANISM P25 1-H FROM TAPE MECHANISM P25 3-F FROM TAPE MECHANISM P25 2-H CNS203 CNS201 CNS204 CNS202 SW703 VOLUME DOWN R612 SW702 VOLUME UP R611 R220 1 2 3 R759 R758 1 2 3 SW705 FAST FORWARD R704 C704 R707 C705 C72 Q208 Q209 C707 R73 40 41 C43 C53 36 30 25 R746 R734 D704 R703 R705 R706 D701 L701 C714 C717 R712 SW714 MEMORY 20 R10 IC5 R29 SW712 BAND SW715 TUNING UP 19 5 R7 C712 Q91 C21 R25 35 10 15 SW716 TUNI
PAGE 28
CD-C602,CP-C602 VOLTAGE VOLTAGE 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 0V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 0V 0V 0V 0V 0V 0V 0V 0V 0V 1.6V 2.5V 2.5V 2.5V 0V 2.5V 0V 0V 0V 2.5V 4V 4V 0V 0V 5V 5V 2.5V 2.5V 1V 1V 2.3V 5V 0V 5V PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 VOLTAGE 0V 0V 2.
PAGE 29
CD-C602,CP-C602 TROUBLESHOOTING When the CD does not function When the CD section does not operate. When the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the troubleshooting instructions.
PAGE 30
CD-C602,CP-C602 • When turntable fails to move. Is there following voltage input on the IC2 pin 28 in the specific state? When the CD mechanism is moved up: 0V In other states: 4.3V No Check the MECHA UP switch and the wiring from the IC2 pin 28 to the MECHA UP switch. Yes Is L output from the IC2 pin 26 during SEC when the disc skip switch is pressed? Check the wiring of IC2 pin 26 and Q93 pin 2. No OK Yes IC2 defective.
PAGE 31
CD-C602,CP-C602 • The CD operating keys work. Check the Focus - HF system. Playback can be performed without a disc. Yes Does the pick-up move up and down twice? Focus search OK Yes No Does the output waveform of IC1(16)(FD) match that shown in Fig. 31-1? Check the area around IC5-CNP2. Yes No Check the IC1(50)(CLK) line, 4MHz. Check the microcomputer data on pins (51)(CL), (52)(DAT) and (53)CE. Focus search is performed two times when play operation is done without disc. 0.5s 0.50 V IC1 16 FD 0.
PAGE 32
CD-C602,CP-C602 • Check the tracking system. Check waveform of IC1 pin 7 (TE). The waveform shown in Fig. 32-1 appears, and no-disc state appears soon. Play is possible in TEST mode. Data cannot be read. Yes Yes Yes Tracking servo is inoperative. Yes Although IL is possible, Yes play is impossible. Check the VCO-PLL system. Check the periphery of IC 1 pin 8 to pin 15, and IC 5 to CNP2. Normal jump is impeded, and the program top cannot be reached. Yes Check the periphery of IC 1 pin 14. 5ms 1.
PAGE 33
CD-C602,CP-C602 FUNCTION TABLE OF IC IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (1/2) Pin No. Port Name Function 1 FIN2 Connection pin for photodiode of pickup. RF signal is generated through addition with FIN pin, and FE signal is generated through subtraction. 2 FIN1 Connection pin for photodiode of pickup. 3 E Connection pin for photodiode of pickup. TE signal is generated through subtraction with F pin. 4 F Connection pin for photodiode of pickup.
PAGE 34
CD-C602,CP-C602 IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (2/2) Pin No. Port Name Function 49 DEF 50 CLK Defect detection output pin of disc. Reference clock input pin. 4.23MHz of DSP is input. 51 CL Microcomputer command clock input pin. 52 DAT Microcomputer command data input pin. 53 CE Microcomputer command chip enable input pin. 54 DRF (DETECT RF) RF level detection output. 55 FSS (Focus Serch Select) Pin to switch focus search mode.
PAGE 35
CD-C602,CP-C602 IC2 VHiLC78622N-1: Servo/Signal Control (LC78622N) (1/2) Pin No. Terminal Name Input/Output 1 DEFI Input Input terminal of defect detection signal (DEF). (Connected to OV when not used.) 2 TAI Input For PLL 3 PDO Output For PLL Output terminal of phase comparison for external VCO control. 4 VVSS — For PLL Ground terminal for integrated VCO. Surely connected to 0V. 5 ISET Input For PLL Resistance connection terminal for current adjustment of PDO output.
PAGE 36
CD-C602,CP-C602 IC2 VHiLC78622N-1: Servo/Signal Control (LC78622N) (2/2) Pin No. Terminal Name Input/Output 50* SFSY (NC) Output Input Function Output terminal of synchronous signal of subcode frame. It drops when subcode stands by. 51 SBCK 52* FSX (NC) Output Output terminal of synchronous signal of 7.35kHz divided from quartz oscillation. 53 WRQ Output Output terminal to stand by output of subcode Q. 54 RWC 55 SQOUT 56 COIN Input Command input terminal from microcomputer.
PAGE 37
CD-C602,CP-C602 IC701 RH-iX0217AWZZ: System Microcomputer (IX0217AW) Pin No. Port Name Terminal Name SEG12-SEG20 Function Input/Output 1-9 S12-S20 Output 10*-12* S21-S23 N.C. — Not connect 13*-20* BP0-BP7 N.C. — Not connect 21-24 COM0-COM3 COM0-COM3 Output LCD Common 25 BIAS BIAS Output LCD Bias 26 VLC0 VLC0 — LCD Bias 27* VLC1 (N.C.) VLC1 — Not connect 28* VLC2 (N.C.
PAGE 38
CD-C602,CP-C602 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 COM0 COMMON COM3 3 COM1 2 COM2 SEG19 SEG20 SEG18 SEG8 SEG17 SEG7 SEG16 SEG6 SEG15 SEG5 SEG14 SEG4 SEG13 SEG3 SEG12 SEG2 SEG11 SEG1 1 SEG9 SEG0 SEGMENT SEG10 LCD701: RV-LX0024AWZZ LCD Display 22 23 24 25 PIN COM1 COM2 COM3 COM4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 TONE LOW X9 4I X6 NC X4 1A X5 2A 3H,3I 3A NC 4A 5B,5C 6A NC 7A ST 8A X-BASS 9A COM1 NC NC NC MEMORY COL 4H X7
PAGE 39
CD-C602,CP-C602 PARTS GUIDE MODEL CD-C602 CP-C602 CD-C602 mini component system consisting of CD-C602 mini component system, CP-C602 and rear (GBOXS0020AWM1) speaker system. “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order.
PAGE 40
CD-C602,CPC602 NO. PRICE RANK PARTS CODE DESCRIPTION CD-C602 INTEGRATED CIRCUITS IC1 IC2 IC5 VHILA9241M/-1 VHILC78622N-1 VHIM56748FP-1 J J J IC91 IC201 VHITA7291S/-1 VHIAN7345K/-1 J J IC301 IC351 VHITA7358AP-1 VHILA1805//-1 J J IC381 IC431 IC601 IC701 VHILC72131/-1 VHILC75394E-1 VHILA4597//-1 RH-IX0217AWZZ J J J J IC921 VHIKIA7805P-1 J AS Servo Amp.
PAGE 41
CD-C602,CPC602 NO.
PAGE 42
CD-C602,CPC602 NO.
PAGE 43
CD-C602,CPC602 NO. PRICE RANK PARTS CODE SW608(257-11) 92LM-SW1658A SW701 92LSWICHT1663T SW702 92LSWICHT1663T SW703 92LSWICHT1663T SW704 92LSWICHT1663T SW705 92LSWICHT1663T SW706 92LSWICHT1663T SW707 92LSWICHT1663T SW708 92LSWICHT1663T SW709 92LSWICHT1663T SW710 92LSWICHT1663T SW711 92LSWICHT1663T SW712 92LSWICHT1663T SW714 92LSWICHT1663T SW715 92LSWICHT1663T SW716 92LSWICHT1663T DESCRIPTION NO.
PAGE 44
CD-C602,CPC602 NO. PRICE RANK PARTS CODE DESCRIPTION NO. ACCESSORIES ! QACCD0015AW00 J ! QACCD0020AWZZ J QANTL0007AWZZ TINSE0235AWZZ TINSK0078AWZZ TINSZ0394AWZZ J J J J TINSZ0395AWZZ J TLABZ0529AWZZ TLABZ0530AWZZ RRMCG0103AWSA 92LLID1782A J J J J AM AC Power Supply Cord [For Canada] AN AC Power Supply Cord [For U.S.A./Central America] AK AM/FM Loop Antenna AD Operation Manual [For U.S.A.] Operation Manual [For Canada] AB Quick Guide [For U.S.A.
PAGE 45
CD-C602,CP-C602 CD-C602 306-2 306 A 306-1 701 306-3 B 304 701 302 704 C 702 702 301 D 303 703x2 E M1 F 305 M2 G 305x2 SW4 H PWB-B 1 2 3 4 Figure 6 CD MECHANISM EXPLODED VIEW –6– 5 6
PAGE 46
CD-C602,CP-C602 CD-C602 606 203 A 613 605 PWB-A2 259,260 267(U.S.A.
PAGE 47
CD-C602,CP-C602 CD-C602 228 609 229 A 229-3 229-2 264 205 605x2 229-1 230 B 224 207 C SW3 222 225 222 222 605x2 206 226 D 222x2 607 265 220 CD MECHANISM E 612 243 244 266 601 614 611 611 245 231 238 221 242 235 222 235 241 232 608 F 269 237 240 SW2 231 G 223 239 610x2 222 234 601 233 603x4 222 H 1 2 3 4 Figure 8 CABINET EXPLODED VIEW (2/2) –8– PWB-C M3 247 (SOLM2) 5 6
PAGE 48
CD-C602,CP-C602 CP-C602 BLACK WOOFER SP1(L-CH) SP2(R-CH) RED A 701 B WOOFER SP1(L-CH) SP2(R-CH) C 706 704x4 D SP1(L-CH) SP2(R-CH) E 702 707x2 F G 705 H 703 1 2 3 4 Figure 9 FRONT SPEAKER EXPLODED VIEW (1/2) –9– 5 6
PAGE 49
CD-C602,CP-C602 GBOXS0020AWM1 A WOOFER SP3(L-CH) SP4(R-CH) 901 B WOOFER SP3(L-CH) SP4(R-CH) C SP3(L-CH) SP4(R-CH) D 903 E WHITE BLACK 902 F G 904x6 905 H 1 2 3 4 Figure 10 REAR SPEAKER EXPLODED VIEW (2/2) – 10 – 5 6
PAGE 50
CD-C602,CP-C602 PACKING OFF THE SET (FOR U.S.A. ONLY) Setting position of switches and knobs Tape Mechanism SPAKP0013AWZZ1 Polyethylene Bag,Unit 92L411-0019 Polyethylene Bag, Front Speaker SPAKA0196AWZZ Packing Add.
PAGE 51
CD-C602,CP-C602 —MEMO— – 12 –
PAGE 52
CD-C602,CP-C602 COPYRIGHT © 1999 BY SHARP COPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.