COLOR TELEVISION MODEL CR20S10 L OPERATION MANUAL L MTS ST EREO As an ENERGY STAR ® Partner, SHARP has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency. ENERGY STAR ® is a U.S. registered trademark. CONTENTS • • • • • • • • • • • • • PAGE IMPORTANT INFORMATION ........................... 2 Before Operating Your Television ........... 2~ 3 Supplied Accessories ........................................ 3 Antenna Connections .............................
Welcome to the SHARP Family. We are pleased that you are now the owner of a SHARP Color Television – built for outstanding quality, reliability and performance. Every SHARP Color Television set is tuned and adjusted for proper color and sound, and has passed through the most stringent quality control tests at the factory. We have prepared this OPERATION MANUAL so that you may adjust the picture and color to your personal viewing preference.
Before Operating Your Television (Continued) CAUTION: DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY FALL CAUSING SERIOUS PERSONAL INJURY AND SERIOUS DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE MANUFACTURER OR SOLD WITH THE PRODUCT. FOLLOW THE MANUFACTURER’S INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING ACCESSORIES RECOMMENDED BY THE MANUFACTURER.
Antenna Connections (Continued) OUTDOOR ANTENNA CONNECTION • Use one of the following two diagrams if you connect an outdoor antenna. A: Using a VHF/UHF combination outdoor antenna. B: Using separate VHF and/or UHF outdoor antenna. • Connect an outdoor antenna cable lead-in to the COAXIAL CABLE CONNECTOR on the rear of the TV set. A. Combination VHF/UHF Antennas B.
Quick Reference Control Operation L Location of Controls (ENGLISH) Front Panel SENSOR AREA FOR REMOTE CONTROL MTS STEREO POWER MENU VIDEO/AUDIO IN TERMINALS (VIDEO/AUDIO terminals are also provided on the rear.) ? CH > – VOL + POWER POWER Press → On. Press again → Off. O -R VIDEO IN L- AUDI ? CH > – VOL + MENU VOLUME UP/DOWN (+) Increases sound. (–) Decreases sound. CHANNEL UP/DOWN – MENU (8) Selects next higher channel. (9) Selects next lower channel.
EZ SETUP during First Use L When you turn on the TV for the first time, it will automatically memorize the broadcast channels. Please perform the following instructions before you press the power button. (1) Insert the batteries into the remote control. (See page 3) (2) Connect the antenna cable to the TV set. (See page 3~ 4) (3) Plug in the AC POWER cord to the wall outlet.
Demo Mode • To quickly learn more about the TV set, press and hold for more than three seconds both CH UP (8) and DOWN (9) on the TV set. The TV set will go into DEMO mode and briefly explain the various features. • To cancel DEMO mode, again press both CH UP (8) and DOWN (9) on the TV set.
Language L The language for the ON SCREEN DISPLAY can be set to ENGLISH, SPANISH or FRENCH. L Setting the ON SCREEN DISPLAY Language. 1 Press MENU to access MAIN MENU screen. S L E E P T I ME R V I D EO A D J U S T AUD I O S E L EC T C L O S E D C A P T I ON P A R E N T CON T RO L E N E RG Y S A V E SE T UP (MAIN MENU screen) 2 Press CH UP (8) or DOWN (9) to move the “ ” mark to “SET UP”.
Video Adjust Description of Adjustment Items POWER TV DVD VCR DISPLAY INPUT Selected item VOL UP (+) button VOL DOWN (–) button 1 2 3 PICTURE To increase contrast To decrease contrast 4 5 6 To make skin tones purplish 7 8 TINT To make skin tones greenish COLOR To increase color intensity To decrease color intensity BRIGHT To increase brightness To decrease brightness SHARP To increase sharpness 0 100 PERSONAL PREFERENCE A B C D VOL + CH MENU To choose a RED, BLUE or STAND
Audio Select L MTS (Multichannel TV Sound) This circuit allows reception of stereo or bilingual TV sound. 1 2 Press MENU to access MAIN MENU screen. Press CH UP (8) or DOWN (9) to move the “ ” mark to “AUDIO SELECT”. CH → CH S L E E P T I ME R V I D EO A D J U S T AUD I O S E L EC T C L O S E D C A P T I ON P A R E N T CON T RO L E N E RG Y S A V E SE T UP (MAIN MENU screen) 3 Press VOL (+) or (–) to access AUDIO SELECT mode. VOL — 4 VOL + Press VOL (+) or (–) to select “STEREO”, “SAP” or “MONO”.
Closed Caption L HOW TO SET CLOSED CAPTION • Your TV is equipped with an internal Closed Caption decoder. “Closed Caption” is a system which allows you to view conversations, narration, and sound effects in TV programs and home videos as subscript on your TV screen as shown on the right. • Not all the programs and videos will offer closed caption. Please look for the “ ” symbol to ensure that captions will be shown. • Closed Caption broadcast can be viewed in two modes: CAPTION and TEXT.
Parent Control (VIEW TIMER) L VIEW TIMER This function allows you to restrict TV viewing time and also allows you to control TV usage. This function is to prevent your children from watching too much TV. VIEWING TIME (an accumulative timer: counts only the time duration acquired while the TV is on.) • VIEWING TIME can be set from 30M (30 minutes) to 10H00M (10 V I EW T I ME R hours) in 30 minutes intervals. OFF TIME (Restricts TV watching after the VIEWING TIME reaches V I EW I NG T I ME – – H – –M zero.
Parent Control (VIEW TIMER Continued) 8 9 Enter the 4-digit SECRET No. using the REMOTE KEYPAD. Press MENU, and SECRET No. is registered. 1 2 3 4 5 7 8 1 S E CR E T 2 3 No . 4 6 9 → ENTER 0 I NPUT 100 Example • To restrict anybody from watching the TV for 5 hours, after watching the TV for 2 hours, your settings would look like this: • They can choose to watch the 2 hours of TV however they wish.
Parent Control (VIEW TIMER Continued) 2 (On the Set) Press and hold both VOL (+) and CH UP (8) on the TV set simultaneously until the VIEW TIMER access screen is displayed. Now you can cancel the VIEW TIMER settings or change the SECRET No. while “INPUT SECRET No.” is displayed. ? CH > VOL + MENU VOL (+)/ CHANNEL UP (8) buttons L Notice of Remaining VIEWING TIME • For every 30 minute interval, the “remaining time” will be displayed for 4 seconds.
Set Up L EZ SETUP By operating the channel preset functions, you can preset your TV to the desired channels for viewing. 1 2 3 4 5 6 7 8 REMOTE KEYPAD 9 VOLUME (+)/(–) ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CHANNEL UP (8)/ DOWN (9) MENU CH VOL — VOL + CH MENU 1 2 Press MENU to access MAIN MENU screen. Press CH UP (8) or DOWN (9) to move the “ ” mark to “SET UP”.
Set Up (Continued) L CHANNEL SETTING If EZ SETUP does not memorize all the channels in your region, follow the instructions below to manually memorize the channel. 1 2 Press MENU to access MAIN MENU screen. Press CH UP (8) or DOWN (9) to move the “ ” mark to “SET UP”. → CH CH S L E E P T I ME R V I D EO A D J U S T AUD I O S E L EC T C L O S E D C A P T I ON P A R E N T CON T RO L E N E RG Y S A V E SE T UP (MAIN MENU screen) 3 4 Press VOL (+) or (–) to access SET UP mode.
Set Up (Continued) L Saving broadcast TV channels into memory. 1.1 Press MENU to access MAIN MENU screen, then press CH UP (8) or DOWN (9) to move the “ ” mark to “SET UP”. Press VOL (+) or (–) to access SET UP mode, then press CH UP (8) or DOWN ( 9 ) to move the “ ” mark to “CH SETTING”. Press VOL (+) or (–) to access CH SETTING screen. Press CH UP (8) or DOWN (9) to move the “ ” mark to “CH SEARCH”, then press VOL (+) or (–) to access CH SEARCH screen. 1.2 1.3 1.4 → VOL — VOL + 2.
Set Up (Continued) 2.4 Press MENU to exit.
Set Up (Continued) L PERSONAL PREFERENCE By setting the PERSONAL PREFERENCE channels in advance, you can select your favorite channels easily. 1 2 3 4 5 6 7 8 FLASHBACK PERSONAL PREFERENCE 9 ENTER 0 100 REMOTE KEYPAD VOLUME (+)/(–) PERSONAL PREFERENCE A B C D CH VOL — VOL + CH MENU MUTE CHANNEL UP (8)/ DOWN (9) MENU 1 2 Press MENU to access MAIN MENU screen. Press CH UP (8) or DOWN (9) to move the “ UP”.
Set Up (Continued) L UNIVERSAL PLUS FUNCTION VCR or DVD input mode will be selected automatically by pressing the VCR or DVD PLAY buttons on the UNIVERSAL REMOTE CONTROL. 4 5 7 8 6 VOLUME (+)/(–) 9 ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL — VOL + CH MENU 1 2 Press MENU to access MAIN MENU screen. Press CH UP (8) or DOWN (9) to move the “ UP”.
Using the Video and Audio Input Jacks L Connecting video equipment for playback of video material. • When the television is connected to video equipment as shown below, the material being played back on the video equipment can be seen on the television screen. Connecting video device equipped with video output terminals.
Using the Video and Audio Input Jacks (Continued) L To watch video material playback. • Press the Remote’s INPUT button to select the VIDEO INPUT mode for the video equipment you wish to play. • The external VIDEO INPUT mode will change as follows each time the INPUT button is pressed.
Operation of Remote Control L “Identifying” Remote VCRs, cable TV conveters and DVDs Your Remote Control has been set at the factory to operate your TV and many remote control VCRs, cable TV converters and DVDs. However, in some cases an easy one-time setup step may be necessary before the Remote will operate accessory VCRs, cable TV converters and DVDs. • In this set-up step, the Remote locates and memorizes the remote control transmitter code for the VCR, cable TV converters and DVDs.
Operation of Remote Control (Continued) DVD/VCR POWER POWER DVD VCR TV TV POWER DISPLAY INPUT DISPLAY REMOTE KEYPAD 1 2 3 4 5 6 7 8 9 ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL — VOL + CH MENU MUTE CATV TV DVD VCR REW PLAY FF PAUSE STOP REC L HOW TO IDENTIFY A VCR The remote control may already be set to operate your VCR. Try this initial check before going on to the following “identify” section. (1) Slide CATV/DVD-TV/VCR switch to VCR.
Operation of Remote Control (Continued) VCR BRAND POWER DVD VCR TV TV POWER DISPLAY DISPLAY 1 2 3 4 5 6 7 8 9 REMOTE KEYPAD ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL + VOL — CH MENU CHANNEL UP (8)/ DOWN (9) MUTE CATV TV DVD VCR REW PLAY FF PAUSE STOP REC REMOTE CONTROL CODE NUMBER INPUT CATV/DVDTV/VCR CH/SKIP TIPS ON IDENTIFYING YOUR VCR: If your VCR model does not have the CHANNEL UP function on its remote control, it cannot be identified using the SEA
Operation of Remote Control (Continued) DVD/VCR POWER POWER DVD VCR TV TV POWER DISPLAY INPUT INPUT REMOTE KEYPAD 1 2 3 4 5 6 7 8 DISPLAY 9 ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL + VOL — CH MENU MUTE CATV TV DVD VCR REW PLAY FF PAUSE STOP REC L HOW TO IDENTIFY A DVD The remote control may already be set to operate your DVD. Try this initial check before going on to the following “identify” section. (1) Slide CATV/DVD-TV/VCR switch to DVD.
Operation of Remote Control (Continued) L HOW TO IDENTIFY A CABLE CONVERTER L To Identify Your Cable Converter –Direct Entry Method. Use the following steps and list to quickly find the remote control code for your cable TV converter. • First look up your converter’s remote code number before going through the direct code entry steps below. • If this procedure does not identify your converter, use the Search method for identification. (1) Slide CATV /DVD-TV/VCR switch to CATV.
Before Calling for Service PROBLEM QUICK SERVICE CHECK LIST POSSIBLE REMEDY No Playback of VCR and Disc Player No Picture or Sound from External Video/Audio Products Remote Control Doesn’t Work Bars on Screen Picture Distorted Picture Rolls Vertically No Color Poor Reception on Some Channels Weak Picture Lines or Streaks in Picture Ghosts in Picture Picture Blurred Sound OK, Picture Poor Picture OK, Sound Poor No Picture or Sound Dark and Blank Picture External Electrical Noise Interfering with TV’s Ope
Specifications MODEL CR20S10 Receiving System NTSC Stereo Broadcast MTS/SAP Reception Channels AIR VHF 2-13 ch UHF 14-69 ch CATV 1-125 ch Channel Tuning 181-channel Reception PLL tuning system Antenna Input Impedance VHF/UHF 75 ohm Unbalanced Screen Size 20˝ Diagonally Measured Terminals Audio/Video input x 2 (Front x 1, Rear x 1) Sound Output 1.
Notes 30 28-30 CR20S10[E].
VALID IN CANADA ONLY LIMITED WARRANTY Consumer Electronics Products Congratulations on your purchase! Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer: Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship.
SHARP ELECTRONICS OF CANADA LTD. 335 BRITANNIA ROAD EAST, MISSISSAUGA, ONTARIO L4Z 1W9 SHARP CORPORATION Printed in Mexico TINS-7347GJZZ 01P07-MMP 32 31-32 CR20S10[E].
TÉLÉVISEUR COULEUR MODÈLE CR20S10 L MODE D’EMPLOI L MTS ST EREO En sa qualité de partenaire ENERGY STAR ®, SHARP a déterminé que ce produit répond ® aux prescriptions ENERGY STAR en matière d’utilisation efficace de l’énergie. ENERGY ® STAR est une marque déposée aux Etats-Unis. TABLE DES MATIÈRES • • • • • • • • • • • • PAGE INFORMATIONS IMPORTANTES ..................... 2 Avant d’utiliser votre téléviseur ................ 2~ 3 Accessoires fournis ............................................
SHARP vous souhaite la bienvenue. Nous sommes très heureux de vous savoir propriétaire d’un téléviseur couleur SHARP – fabriqué pour offrir une qualité, une fiabilité et un rendement remarquables. Chaque téléviseur couleur SHARP a été correctement syntonisé et réglé afin d’assurer une image couleur et un son parfaits, et a subi à l’usine les tests de contrôle de qualité les plus stricts. Ce MODE D’EMPLOI vous permettra de régler l’image et la couleur selon vos goûts personnels.
Avant d’utiliser votre téléviseur (Suite) ATTENTION : NE PAS PLACER CET APPAREIL SUR UNE TABLE, UN CHARIOT, UN TRÉPIED OU UN SUPPORT QUI N’EST PAS STABLE. L’APPAREIL POURRAIT TOMBER ET CAUSER DES BLESSURES GRAVES ET SUBIR DES DOMMAGES IMPORTANTS. UTILISER SEULEMENT SUR UNE TABLE, UN CHARIOT, UN TRÉPIED OU UN SUPPORT RECOMMANDÉS PAR LE FABRICANT OU VENDU AVEC L’APPAREIL. SUIVRE LES INSTRUCTIONS DU FABRICANT POUR INSTALLER L’APPAREIL ET UTILISER LES DISPOSITIFS DE MONTAGE RECOMMANDÉS PAR LE FABRICANT.
Connexions d’antennes (Suite) CONNEXION D’ANTENNE EXTÉRIEURE • S’inspirer de l’un des deux schémas suivants en cas d’utilisation d’une antenne extérieure. A : Avec une antenne extérieure combinée VHF/UHF. B : Avec deux antennes extérieures séparées VHF et/ou UHF. • Connecter un câble conducteur d’antenne extérieure au connecteur ANT/CABLE situé à l’arrière du téléviseur. A. Combinaison d’antennes VHF / UHF B.
Référence rapide sur les commandes L Emplacement des touches (FRANÇAIS) Panneau Avant ZONE DE DETECTION DU CAPTEUR MTS STEREO -R VIDEO IN L- AUDIO MENU PRISES D’ENTRÉE VIDÉO/ AUDIO IN (Les prises VIDÉO/AUDIO sont également reprises à l’arrière.) ? CH > – VOL + POWER ALIMENTATION (POWER) Appuyer pour mettre sous tension. Appuyer de nouveau pour mettre hors tension. ? CH > – VOL + POWER MENU AUGMENTATION/RÉDUCTION DU VOLUME SONORE (VOL) (+) Pour augmenter le volume du son.
PRÉRÉGL AUTO CANAL lors de la première utilisation L Lorsque le téléviseur est mis sous tension pour la première fois, il mémorise automatiquement les différents canaux. Suivre les instructions suivantes avant d’appuyer sur l’interrupteur d’alimentation. 3) (1) Insérer les piles dans la télécommande. (Voir page (2) Raccorder le câble d’antenne au téléviseur. (Voir les pages 3 ~ 4) (3) Brancher le cordon d’alimentation sur la prise murale.
Mode Demo • Pour apprendre plus rapidement à utiliser le téléviseur, appuyez simultanément sur les touches de CH UP (8) et de CH DOWN (9) du téléviseur et maintenez-les enfoncées pendant plus de trois secondes. Le téléviseur passe en mode DEMO et explique brièvement ses différentes fonctionnalités. • Pour annuler le mode DEMO, appuyez de nouveau simultanément sur les touches de CH UP (8) et de CH DOWN (9) du téléviseur.
Langue L La langue de l’affichage sur écran peut être l’anglais, l’espagnol ou le français. L Sélection de la langue de l’affichage sur écran. 1 Appuyer sur MENU pour accéder au MENU PRINCIPAL. M I NU T . R EG L AGE R E G L A G E I MAG E S E L EC . AUD I O S OU S - T I T R A G E A U T OR I T E P A R E N T E CON E RG I E R EG L AGE (Écran MENU PRINCIPAL) 2 Appuyer sur CH UP (8) ou DOWN (9) pour déplacer le repère “ ” à “REGLAGE”.
Réglage image Description des rubriques de réglage Rubrique sélectionnée Touche VOL UP (+) CONTRASTE (PICTURE) Pour augmenter le contraste TEINTE (TINT) COULEUR (COLOR) Pour diminuer le contraste Les tonalités de la peau deviennent verdâtres Les tonalités de la peau virent au pourpre Davantage d’intensité de couleur LUMINOSITE (BRIGHT) Davantage de luminosité NETTETE (SHARP) POWER TV 1 2 DISPLAY INPUT 2 3 4 5 6 7 8 VOLUME (+)/(–) 9 ENTER FLASHBACK Moins d’intensité de couleur 100 PERSO
Selec. Audio L MTS (Multichannel TV Sound) Ce circuit permet la réception d’un son bilingue ou stéréo sur votre téléviseur. 1 2 Appuyer sur MENU pour accéder au MENU PRINCIPAL. Appuyer sur CH UP (8) ou DOWN (9) pour déplacer le repère “ ” à “SELEC. AUDIO”. → CH CH M I NU T . R EG L AGE R E G L A G E I MAG E S E L EC . A UD I O S OU S - T I T R A G E A U T OR I T E P A R E N T E CON E RG I E R EG L AGE (Écran MENU PRINCIPAL) 3 Appuyer sur VOL (+) ou (–) pour accéder au mode de SELEC.
Sous-titrage L RÉGLAGE DU MODE SOUS-TITRAGE • Ce téléviseur est équipé d’un décodeur de sous-titrage intégré. Ce système permet de visionner les conversations, narrations, ainsi que les effets sonores des programmes télévisés et des cassettes vidéo sous forme de sous-titrage apparaissant à l’écran de la manière illustrée ci-contre. • Ce ne sont pas tous les programmes télévisés et les vidéos qui comportent des sous-titrages. Vérifier si le symbole “ ” est indiqué pour s’assurer que le sous-titrage apparaît.
Autorite Parent (LIMITEUR) L LIMITEUR Cette fonction vous permet de limiter le temps passé à regarder la télévision et vous permet également de commander l’utilisation du téléviseur. Cette fonction est conçue pour empêcher vos enfants de trop regarder la télévision. DUREE (minuterie cumulative : compte uniquement la durée lorsque le téléviseur est sous tension.) • Les DUREE peuvent aller de 30M (30 minutes) à 10H00M (10 heures) L I M I T EU R par intervalles de 30 minutes.
Autorite Parent (LIMITEUR Suite) 8 9 Saisissez le numéro secret à 4 chiffres à l’aide du CLAVIER DE LA TÉLÉCOMMANDE. 1 2 3 Appuyez sur MENU, le No.SECRET est enregistré. 4 5 7 8 9 100 1 2 Pour modifier les réglages de la LIMITEUR. (le No.SECRET est enregistré) Répétez les étapes de la section “Comment régler la VOL VOL LIMITEUR” et sélectionnez “LIMITEUR DU AUTORITE — + PARENT” à l’étape 3. Appuyez sur les touches VOL (+) ou (–), le “ENTRER No.SECRET” s’affiche. Saisissez le No.
Autorite Parent (LIMITEUR Suite) 2 (Sur l’appareil) Appuyez simultanément sur les touches VOL (+) et CH UP (8) du téléviseur et maintenez-les enfoncées jusqu’à l’affichage de l’écran d’accès à la LIMITEUR. Vous pouvez ensuite annuler les réglages de la LIMITEUR ou changer de No.SECRET lorsque le message “ENTRER No.SECRET” s’affiche.
Réglage L PREREGL AUTO CANAL Cette opération vous permet de prérégler le téléviseur sur les canaux que vous souhaitez regarder. 1 2 3 4 5 6 7 8 REMOTE KEYPAD 9 VOLUME (+)/(–) ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CHANNEL UP (8)/ DOWN (9) MENU CH VOL — VOL + CH MENU 1 2 Appuyer sur MENU pour accéder au MENU PRINCIPAL. Appuyer sur CH UP (8) ou DOWN (9) pour déplacer le repère “ ” à “REGLAGE”. → CH CH MUTE M I NU T . R EG L AGE R E G L A G E I MAG E S E L EC .
Réglage (Suite) L REGLAGE CANAL Si PREREGL AUTO CANAL ne mémorise pas tous les canaux diffusés dans la région, suivre les instructions ci-dessous pour mémoriser manuellement le canal voulu. 1 2 Appuyer sur MENU pour accéder au MENU PRINCIPAL. Appuyer sur CH UP (8) ou DOWN (9) pour déplacer le repère “ ” à “REGLAGE”. → CH CH M I NU T . R EG L AGE R E G L A G E I MAG E S E L EC .
Réglage (Suite) L Enregistrement des canaux TV en mémoire. 1.1 Appuyer sur MENU pour accéder au MENU PRINCIPAL, appuyer sur CH UP (8 ) ou DOWN (9) pour déplacer le repère “ ” à “REGLAGE”. Appuyer sur VOL (+) ou (–) pour accéder au mode de REGLAGE, appuyer sur CH UP (8) ou DOWN (9) pour déplacer le repère “ ” à “REGLAGE CANAL”. Appuyer sur VOL (+) ou (–) pour accéder à l’écran de REGLAGE CANAL. 1.2 1.3 1.
Réglage (Suite) 2.4 POWER Appuyer sur MENU pour sortir.
Réglage (Suite) L PREFERENCES En réglant les chaînes de PREFERENCES à l’avance, vous pouvez facilement sélectionner vos chaînes préférées. 1 2 3 4 5 6 7 8 FLASHBACK PERSONAL PREFERENCE 9 ENTER 0 100 PERSONAL PREFERENCE A B C D CH VOL — VOL + CH MENU MUTE REMOTE KEYPAD VOLUME (+)/(–) CHANNEL UP (8)/ DOWN (9) MENU 1 2 Appuyer sur MENU pour accéder au MENU PRINCIPAL. Appuyer sur CH UP (8) ou DOWN (9) pour déplacer le repère “ ” à “REGLAGE”. CH → CH M I NU T .
Réglage (Suite) L FONCTION UNIVERSAL PLUS Le mode d’entrée du magnétoscope ou du lecteur de DVD est sélectionné automatiquement en appuyant sur la touche VCR ou DVD PLAY de la TÉLÉCOMMANDE UNIVERSELLE. 4 5 7 8 6 VOLUME (+)/(–) 9 ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL + VOL — CH MENU MUTE CATV 1 2 Appuyer sur MENU pour accéder au MENU PRINCIPAL. Appuyer sur CH UP (8) ou DOWN (9) pour déplacer le repère “ ” à “REGLAGE”.
Utilisation des prises d’entrée vidéo et audio L Connexion d’un appareil vidéo pour visionner une bande vidéo. • Lorsque le téléviseur est connecté à un appareil vidéo comme illustré ci-dessous, la bande reproduite sur l’appareil vidéo peut être visionnée sur l’écran du téléviseur. Connexion d’un dispositif vidéo équipé d’une borne de sortie vidéo.
Utilisation des prises d’entrée vidéo et audio (Suite) L Pour visionner la bande vidéo. • Appuyer sur INPUT de la télécommande pour sélectionner le mode d’entrée vidéo (VIDEO INPUT) adapté à l’appareil vidéo à visionner. • Chaque appui de la touche INPUT change le mode d’entrée vidéo VIDEO INPUT externe de la manière suivante.
Utilisation de la télécommande L “Identification” des magnétoscopes, adaptateurs de câblodistribution et lecteurs de DVD télécommandés. Votre télécommande a été réglée en usine pour fonctionner avec votre téléviseur et de nombreux magnétoscopes, adaptateurs de câblodistribution et lecteurs de DVD télécommandés.
Utilisation de la télécommande (Suite) DVD/VCR POWER POWER DVD VCR TV TV POWER DISPLAY INPUT DISPLAY REMOTE KEYPAD 1 2 3 4 5 6 7 8 9 ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL + VOL — CH MENU MUTE CATV TV DVD VCR REW PLAY FF PAUSE STOP REC L COMMENT IDENTIFIER UN MAGNÉTOSCOPE Il est possible que la télécommande soit déjà prête à commander votre magnétoscope.
Utilisation de la télécommande (Suite) POWER DVD VCR TV TV POWER DISPLAY DISPLAY 1 2 3 4 5 6 7 8 9 REMOTE KEYPAD ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL + VOL — CH MENU CHANNEL UP (8)/ DOWN (9) MUTE CATV TV DVD VCR REW PLAY FF PAUSE STOP REC MARQUE DU MAGNÉTOSCOPE CODE DE TÉLÉCOMMANDE Akai Audio Dynamics Broksonic Canon Capehart Craig Curtis Mathis Daewoo DBX Dynatech Emerson Fisher Funai GE Goldstar Hitachi Instant Replay JC Penney JVC Kenwood Lloyds Ma
Utilisation de la télécommande (Suite) DVD/VCR POWER POWER DVD VCR TV TV POWER DISPLAY INPUT INPUT REMOTE KEYPAD 1 2 3 4 5 6 7 8 DISPLAY 9 ENTER FLASHBACK 0 100 PERSONAL PREFERENCE A B C D CH VOL + VOL — CH MENU MUTE CATV TV DVD VCR REW PLAY FF PAUSE STOP REC L COMMENT IDENTIFIER UN LECTEUR DE DVD Il est possible que la télécommande soit déjà prête à commander votre lecteur de DVD.
Utilisation de la télécommande (Suite) L COMMENT IDENTIFIER UN ADAPTATEUR DE CÂBLODISTRIBUTION L Pour identifier votre adaptateur de câblodistribution – Méthode de saisie directe. Utilisez les étapes et la liste suivantes pour trouver rapidement le code de la télécommande de votre adaptateur de câblodistribution. • Recherchez d’abord le code de la télécommande de votre adaptateur avant de procéder aux étapes suivantes de saisie directe du code.
Avant d’appeler un réparateur PROBLÈME LISTE DES VÉRIFICATIONS POUR UN DÉPANNAGE RAPIDE SOLUTION POSSIBLE Pas de reproduction d’un magnétoscope ou lecteur de disque Pas d’image ou de son d’un appareil vidéo/audio externe La télécommande ne fonctionne pas Barres sur l’écran Distorsion de l’image L’image défile verticalement Pas de couleur Faible réception de certains canaux Image affaiblie Lignes ou rayures dans l’image Images fantômes Image brouillée Son normal, image médiocre Image normale, son médiocre
Spécifications MODÈLE CR20S10 Système de réception NTSC Diffusion stéréo MTS/SAP Canaux de réception AIR VHF canaux 2 à 13 UHF canaux 14 à 69 CATV canaux 1 à 125 Syntonisation des canaux Système de syntonisation PLL de réception de 181 canaux Impédance d’entrée de l’antenne Déséquilibre de 75 ohm VHF/UHF Taille de l’écran 20˝ diagonale Bornes Entrée Audio/Vidéo x 2 (avant x 1, arrière x 1) Sortie audio 1,5 W (RMS) x 2 Alimentation 120 V CA, 60 Hz Consommation électrique 74 W Dimen
Remarques 30 30-32 CR20S10[F].
POUR CANADA SEULEMENT GARANTIE LIMITÉE Produits électroniques grand public Bravo! Vous venez de faire un excellent achat! Sharp Électronique du Canada Ltée (ci-après nommée “Sharp”) donne la garantie expresse suivante à l’acheteur initial du produit ci-dessous mentionné de Sharp, si celui-ci est emballé dans son contenant original et s’il est vendu et distribué au Canada par Sharp ou par un détaillant autorisé Sharp.
SHARP ÉLECTRONIQUE DU CANADA LTÉE. 335 BRITANNIA ROAD EAST, MISSISSAUGA, ONTARIO L4Z 1W9 SHARP CORPORATION Imprimé en Mexico TINS-7347GJZZ 01P07-MMP 32 30-32 CR20S10[F].