R CLIMATISEUR DE CHAMBRE DE TYPE PORTATIF MANUEL D’INSTALLATION ET D’UTILISATION * Plasmacluster is a trademark of SHARP Corporation. * Plasmacluster est une marque de commerce de SHARP Corporation.
ENGLISH This manual explains the proper use of your new air conditioner. Please read this manual carefully before using the product. This manual should be kept in a safe place for handy reference. CONTENTS • FOR CUSTOMER ASSISTANCE (U.S.) ................ E-2 • CONSUMER LIMITED WARRANTY (U.S.) ........... E-3 • FOR CUSTOMER ASSISTANCE (CANADA) ........ E-4 • CONSUMER LIMITED WARRANTY (CANADA) ... E-5 • PRECAUTIONS ..................................................... E-6 • INCLUDED .......................
FOR CUSTOMER ASSISTANCE (the United States) To aid in answering questions if you call for service or for reporting loss or theft, please record below the model and serial number located on the back side of the unit.
CONSUMER LIMITED WARRANTY CONSUMER LIMITED WARRANTY FOR THE U.S.
FOR CUSTOMER ASSISTANCE (Canada) To aid in answering questions if you call for service or for reporting loss or theft, please record below the model and serial number located on the back side of the unit.
R LIMITED WARRANTY Consumer Electronics Products Congratulations on your purchase! Sharp Electronics of Canada Ltd.
PRECAUTIONS Points to keep in mind when using your air conditioner. WARNINGS FOR USE • Install the air conditioner in accordance with the installation instructions in the latter section of this manual. • Do not modify any part of this product. • Do not insert anything into any part of the unit. • Ensure the power supply used has an appropriate voltage rating. Only use a three-pin grounded electrical AC socket rated 125V, 60Hz, and 15 amps or more as shown on the right.
WARNING ABOUT GROUNDING • Do not under any circumstances cut or remove the round grounding pin from this plug. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in any doubt as to whether the appliance is properly grounded. If a grounding adapter is used, make sure the socket box is fully grounded.
PRECAUTIONS NOTES ON OPERATION • Allow 3 minutes for the compressor to restart cooling. If you turn the air conditioner off and immediately restart it, allow three minutes for the compressor to restart cooling. There is an electronic device in the unit that keeps the compressor turned off for three minutes for safety. • In the event of a power failure during use, allow 3 minutes before restarting the unit. After power is reinstated, restart the air conditioner.
LOCATION MIN.12" (30cm) MIN.12" (30cm) INCLUDED Exhaust hose (1) Window exhaust adapter (1) Drainage Grommet (1) Exhaust cover (1) Bracket (1) Extension panel (1) Adjustment panel (1) Window panel (1) Rain guard (2) Insect guard net (1) Hose clamp (1) Screw (8) Foam seal (1) Foam seal (3) (adhesive type)A Foam seal (1) (adhesive type)B (thickness:1/5") (thickness:2/5") Remote control (1) Battery (2) (AAA.R03) Manual (1) SUGGESTED TOOLS FOR WINDOW PANEL INSTALLATION 1.
PART NAMES FRONT VIEW 1 1 Air Outlet 2 2 Vertical louvers 3 4 5 3 Horizontal louvers 4 PLASMACLUSTER Lamp (blue) 6 5 Remote control signal receiver window 7 6 AUX.
REMOTE CONTROL 1 1 Transmitter 2 Display 3 POWER Button 4 LIGHTS Button 3 4 5 6 7 8 9 0 q w e r t 5 TEMPERATURE Button 6 PLASMACLUSTER Button 7 1 hr OFF Button 8 MODE Button 9 ON TIMER Button ENGLISH 2 0 FAN Button q OFF TIMER Button w CANCEL Button e LOUVERS Button r RESET Button t MEGA COOL Button REMOTE CONTROL DISPLAY y MODE SYMBOLS y u : COOL : DEHUMIDIFICATION : FAN : VENTILATION p i a o s u MEGA COOL SYMBOL i PLASMACLUSTER SYMBOL o FAN SPEED SYMBOLS : AUTO : Manual setting p TEMPERA
INSTALL WINDOW PANEL Installation in a double-hung sash window (See page 14 for installation in a sliding sash window. ) Hole 1 2 Connect the rain guards to the insect guard net. Insert all three projections on each rain guard into the holes in the insect guard net. Side “A” will now be uppermost, as indicated in the diagram. Attach the guard combined above to the window panel Push the insect guard net firmly to ensure that its four projections fit into the holes in the window panel.
Adjustment panel If the inner width of the window is between 24" (609mm) and 36.8" (934mm) inclusive. (1) Open the window sash and place the window panel on the window stool. (2) Slide the adjustment panel to fit the window frame width. 24"~36.8" (3) Secure the window panel to the stool with 3 screws. If the inner width of the window is between 36.8" (934mm) and 48" (1219mm) inclusive. ENGLISH Extension panel (1) Attach the extension panel to the adjustment panel.
INSTALL WINDOW PANEL Installation in a sliding sash window (See page 12 for installation in a double-hung window.) "A" 1 Connect the rain guards to the insect guard net. Insert all three projections on each rain guard into the holes in the insect guard net. Side “A” will now be uppermost, as indicated in the diagram. Insect guard net Hole Rain guard Projection 2 3 Attach the guard combined above to the window panel.
If the inner height of the window is between 24" (609mm) and 36.8" (934mm) inclusive. Adjustment panel (1) Open the window sash and place the window panel on the window frame. (2) Slide the adjustment panel to fit the window frame height. 24"~36.8" (3) Secure the window panel to the window frame with 3 screws. Extension panel (1) Attach the extension panel to the adjustment panel. 36.8"~48" (2) Open the window sash and place the window panel on the window frame.
INSTALLATION AND REMOVAL OF EXHAUST HOSE The exhaust hose must be installed or removed in accordance with the usage mode. MODE EXHAUST HOSE COOL, FAN, VENTILATION, DEHUMIDIFICATION with no container Install DEHUMIDIFICATION with container(minimum capacity 3 gallons) Remove Installation of the exhaust hose 1 Attach the window exhaust adapter to the exhaust hose. Extend one end of the exhaust hose and insert it into the window exhaust adapter, and turn it (approx. three times) until it stops.
Removal of the exhaust hose ndow haust apter 2 Remove the window exhaust adapter. Pull out and remove the window exhaust adapter by pushing down two “PUSH” markings, and slide and close the exhaust cover in the window panel. "PUSH" ENGLISH 1 Remove the exhaust hose adapter from the unit. Lift up and remove the exhaust hose adapter from the unit by pushing down on the two projections.
PRE-OPERATION CHECKS POWER PLUG CHECK This air conditioner uses a fused power plug. Always check the power plug before use. 1 2 3 Press the RESET button. 4 Press the RESET button until you hear another CLICK. The circuit breaker is activated, power is supplied, and the air conditioner is now ready for use. RESET TEST Insert the power plug into the wall socket. Press the TEST button. You will hear a CLICK if the circuit breaker is functioning correctly.
HOW TO USE THE REMOTE CONTROL Point the remote control towards the units signal receiver window and press the desired button. A beep will sound when the unit receives the signal. • Make sure nothing, such as curtains, blocks the signal receiver window. • The remote control operates up to 23 feet (7 meters) away. • Do not expose the signal receiver window to direct sunlight. This may adversely affect its operation. If necessary, close the curtains to block out the sunlight.
COOL MODE 1 Install the exhaust hose (See Page16), turn the drainage nozzle to the CLOSE position, and check the drainage nozzle is covered Drainage nozzle "CLOSE" position with the stopcock. Stopcock 1 Press the MODE button to select COOL mode. COOL 32 DEHUM FAN VENT Press the POWER button to start operation. • The red OPERATION lamp on the unit will light. 2 3 1 4 3 Press the TEMPERATURE button to set the desired temperature. • The temperature can be set within the range of 64°F to 86°F.
DEHUMIDIFICATION MODE In this mode, the air conditioner dehumidifies the room. Dehumidification with container 4 5 Remove the exhaust hose (See Page 17) Drainage nozzle Turn the drainage nozzle to the OPEN position. Stopcock Pull the stopcock out from the drainage nozzle. • When the stopcock is removed, a small amount of water may be discharged from the drainage nozzle. • Always perform this procedure with the unit turned off. Drain water will spout out if attempted during operation.
FAN MODE In this mode, the air conditioner simply circulates the air without cooling it. Install the exhaust hose (See Page16), turn the drainage nozzle to the CLOSE position, and check the drainage nozzle is covered with the stopcock. 2 2 5 3 1 31 1 Press the MODE button to select FAN mode. 2 Press the POWER button to start operation. 3 Press the FAN button to set the desired fan speed. COOL DEHUM FAN VENT • The red OPERATION lamp on the unit will light. • The temperature cannot be set.
TO CHANGE AIR FLOW DIRECTION UP / DOWN AIR FLOW DIRECTION 1 Press the LOUVERS button on the remote control. • The horizontal louvers will swing continuously. Press the LOUVERS button again when the horizontal louvers are at the desired position. • The horizontal louvers will stop moving. • The adjusted position will be memorized and the same position will be set automatically when operated the next time. NOTE • During VENTILATION mode, UP/DOWN air flow direction cannot be changed.
PLASMACLUSTER OPERATION The Plasmacluster ion generator inside the air conditioner will release positive and negative Plasmacluster ions into the room. Approximately the same numbers of positive and negative ions released into the air. 1 Press the PLASMACLUSTER button during operation. • The remote control will display “ ”. • The blue PLASMACLUSTER lamp on the unit will light. TO CANCEL 1 Press the PLASMACLUSTER button again. • The PLASMACLUSTER lamp on the unit will turn off.
MEGA COOL OPERATION In this operation, the air conditioner fan works at extra high speed with a setting temperature of 59°F. 1 Press the MEGA COOL button during cooling mode. • The remote control will display " ". • The temperature display will go off. • The green MEGA COOL lamp on the unit will light. TO CANCEL Press the MEGA COOL button again. 1 NOTES: • You cannot set the temperature or fan speed during MEGA COOL operation.
TIMER OPERATION OFF TIMER The unit will turn off automatically according to your setting. Timer duration can be set from a minimum of half an hour (30 minutes) to a maximum of 12 hours. Up to 9.5 hours, you can set in half-hour (30-minutes) increments and from 10 to 12 hours, in 1-hour increments. Point the remote control at the signal receiver window on the unit. the OFF TIMER button and set the time 1 Press as desired. • The time setting will change as you press the button as follows. 0.5h 1.0h 1.
ON TIMER The unit will turn on automatically according to your setting. Timer duration can be set from a minimum of half an hour (30 minutes) to a maximum of 12 hours. Up to 9.5 hours, you can set in half-hour (30-minute) increments and from 10 to 12 hours, in 1-hour increments. Point the remote control at the signal receiver window on the unit. the ON TIMER button. 1 Press • The time setting will change as you press the button as follows. 1 1.0h 1.
AUXILIARY MODE Use this mode when the remote control is not available. 1 1 Press the AUX. button on the unit. • The red OPERATION lamp on the unit will light and the unit will start operating in COOL mode. • The fan speed is set to AUTO. • The temperature setting is automatically set according to the room temperature. TO TURN OFF Press the AUX. button again. • The red OPERATION lamp on the unit will turn off. NOTES: • If the AUX. button is pressed during normal operation, the unit will turn off.
DRAINAGE Prepare for drainage and drain out water within the unit in the following cases. If the unit stops operating and the TIMER, OPERATION and MEGA COOL lamps are blinking. (This indicates that the water tank inside the unit is full.) Make sure to turn the unit off. Turn the drainage nozzle to the OPEN position. Pull the stopcock out from the drainage nozzle. • When the stopcock is removed, a small amount of water may be discharged from the drainage nozzle.
MAINTENANCE Be sure to disconnect the power from the wall socket before performing any maintenance. CLEANING THE FILTERS If the filter is clogged with dust, the airflow will be reduced, resulting in poor cooling performance. The filter should be cleaned every two weeks. 1 REMOVE THE FILTERS 2 CLEAN THE FILTERS 3 REINSTALL THE FILTERS Filters • Gently pull the filter handle to the right and slide the filter out of the unit. • Use a vacuum cleaner to remove any dust.
BEFORE CALLING FOR SERVICE If the unit appears to be malfunctioning, check the following points before calling for a service.