Unit installation

ManualsBrandsSharp ManualsComputer equipmentDM 2010 - B/W Laser Printer

[7] SIMULATIONS

1. Entering the simulation mode

Perform the following procedure to enter the simulation mode.

Clear key ! Interrupt key ! "0" key ! Interrupt key ! Main code !

Start key ! Sub code ! Start key

2. Cancelling the simulation mode

When the clear all key is pressed, the simulation mode is cancelled.

When the interruption key is pressed, the process is interrupted and the

screen returns to the sub code entering display.

* After canceling the simulation mode, be sure to turn OFF/ON the

power and check the operation.

3. List of simulations

Main

code

Sub

code

Contents "

1 1 Mirror unit operation check

2 Optical system sensor operation check

2 1 SPF aging ADF

2 SPF sensor operation check ADF

3 SPF motor forward rotation operation check ADF

4 SPF motor reverse rotation operation check ADF

8 SPF paper feed solenoid operation check ADF

9 RSPF reverse solenoid operation check AD

10 RSPF paper exit gate solenoid operation

check

11 SPF PS release solenoid operation check ADF

3 2 Shifter job separator sensor operation check AEF

3 Shifter operation check E

4 Job separator operation check AF

11 Shifter Home Position Check E

5 1 Operation panel display check

2 Heater lamp lighting check, cooling fan

motor operation check

3 Copy lamp lighting check

6 1 Paper feed solenoid operation check

10 Main cassette semi-circular roller drive

7 1 Aging with warmup time display

4 Warmup saving

6 Intermittent aging

8 Warmup time display

9 1 Duplex motor forward rotation operation

check

2 Duplex motor reverse rotation operation

check

4 Duplex motor rotation speed adjustment B

5 Duplex motor switchback time adjustment B

10 Toner motor operation check

14 Trouble (except for U2) cancel

16 U2 trouble cancel

20 1 Maintenance counter clear

21 1 Maintenance cycle setting

2 Mini maintenance cycle setting

22 1 Maintenance counter display

2 Maintenance preset value display

3 JAM memory display

4 Total JAM counter display

5 Total counter display

6 Developing counter display

7 Developing preset counter value display

8 SPF counter display ADF

9 Paper feed counter display

12 Drum counter display

14 Copier ROM version display

Main

code

Sub

code

Contents "

22 15 Trouble memory display

16 Duplex print counter display B

17 Copy counter display

18 Printer counter display A

19 Electronic sort counter display AD

21 Scanner counter display

24 1 JAM memory, JAM counter clear

2 Trouble memory clear

4 SPF counter clear ADF

5 Duplex counter clear B

6 Paper feed counter clear

7 Drum counter clear

8 Copy counter clear

9 Printer counter clear A

10 Electronic sort counter clear AD

13 Scanner counter clear

25 1 Main motor operation check

10 Polygon motor operation check

26 1 Option switch display

3 Auditor setting

5 Counter mode setting

6 Destination setting

7 CRUM set value display

10 Model name setting

22 Language setting

30 CE mark conformity control setting

32 Fan rotation duty change state setup

37 Cancel of stop at developer life over

38 Cancel of stop at dram life over

42 Transfer timing adjustment

50 Black-white reversion function setup

51 Sort/Group copy temporary stop function

setup

30 1 Machine sensor operation check

41 2 OC document sensor adjustment C

3 Document sensor light reception level display C

42 1 Developing counter clear

43 1 Fusing temperature setting

46 1 Copy density level adjustment

19 AE mode picture quality change

48 1 Main scanning (front/rear) direction

magnification ratio adjustment

(Copy/FAX/OC-SPF common)

2 OC mode sub scanning direction

magnification ratio adjustment in copying

5 SPF mode sub scanning direction

magnification ratio adjustment in copying

50 1 Copy image lead edge position adjustment

10 Paper off center adjustment

13 OC mode document off center adjustment

16 SPF mode document off center adjustment D

18 Duplex memory reverse print adjustment B

19 Duplex rear edge void adjustment B

51 2 Resist amount adjustment

63 1 Shading data check

64 1 Self printing mode

67 14 Printer Flash ROM Data Download A

"A: Only when an option is installed.

B: AR-206/207 only

C: Other than AR162/163

D: AR-207 only

E: Other than AR-162

F: AR-F201 only

AR-162 SIMULATIONS – 1

AR-162, AR-163, AR-201, AR-206, AR-207, AR-F201

Summary of content (22 pages)

PAGE 1
AR-162, AR-163, AR-201, AR-206, AR-207, AR-F201 [7] SIMULATIONS Main code 22 1. Entering the simulation mode Perform the following procedure to enter the simulation mode. Clear key ! Interrupt key ! "0" key ! Interrupt key ! Main code ! Start key ! Sub code ! Start key 2. Cancelling the simulation mode When the clear all key is pressed, the simulation mode is cancelled. When the interruption key is pressed, the process is interrupted and the screen returns to the sub code entering display.
PAGE 2
4. Contents of simulations Main code Sub code Contents 1 1 Mirror unit operation check Details of operation Used to execute scanning at the speed corresponding to the set magnification ratio.
PAGE 3
Main code Sub code 3 2 Contents Shifter job separator sensor operation check 3 Shifter operation check 4 Job separator operation check 11 Shifter Home Position check 5 6 Details of operation Used to check the sensors state in the shifter job separator with the LED on the operation panel.
PAGE 4
Main code Sub code 7 1 Contents Aging with warmup time display Details of operation Initial value Execute the simulation input with the copier side cover open, then close the side cover, and the machine will start warming up. Warm up time is counted up every 2nd and it is displayed. After completion of warmup, count up is terminated.
PAGE 5
Main code Sub code 21 2 Contents Mini maintenance cycle setting 22 Details of operation Used to display the currently set mini maintenance cycle at the numbers shown at right. When the set value is entered and the start key is pressed, the set value is stored. 0: 1: 2: 3: Key operation/Display 2500 sheets 4: 30000 sheets 5000 sheets 10000 sheets FREE (999999 sheets) 1 Maintenance counter display Used to display the current maintenance counter value.
PAGE 6
Main code Sub code 22 16 Duplex print counter display 17 Copy counter display Used to display the current copy counter value. !1 18 Printer counter display Used to display the current printer counter value. !1 19 Electronic sort counter display Used to display the current electronic sort counter value. !1 21 Scanner counter display Used to display the current scanner counter value.
PAGE 7
Main code Sub code 26 1 Contents Option switch display Details of operation 0 0 ! 2 0 0 ! 3 Display Magnification ratio display key Auditor setting Set range Used to display the installed option on the operation panel. (The LED corresponding to the installed option is lighted.
PAGE 8
Main code Sub code 26 6 Contents Destination setting Details of operation Used to display the current destination setting with the numbers at right. After entering the set value, press the start key, and the set value is stored. 0: 1: 2: 3: 4: 5: 6: 7: 7 CRUM set value display Model name setting Language setting CE mark conformity control setting 0 ! 11 0 0 ! 30 0 0 ! 7 0 0 ! 1 0 0.
PAGE 9
Main code Sub code 26 37 Contents Cancel of stop at developer life over Details of operation The currently set value is displayed. Enter a set value and press the START key, then the set value is registered. Initial value Set range 1 0 ! 1 0 0 ! 1 5 1, 3, 5, 7, 9 0 0.1 1 0.1 Key operation/Display 0: Stops the machine at developer life over. 1: Does not stop the machine at developer life over.
PAGE 10
Main code Sub code 41 3 Contents Document sensor light reception level display Details of operation Initial value Set range 170 155 " 190 48 1 " 99 1 1 " 2 58 1 " 99 50 1 " 99 Used to display the light reception level and the detection level of the document sensor. (The sensor level adjusted with SIM 41-2 is displayed.
PAGE 11
Main code Sub code 48 5 Contents SPF mode sub scanning direction magnification ratio adjustment in copying 50 1 Copy image position adjustment Details of operation After completion of warmup, shading is performed and the currently set SPF mode sub scanning direction magnification ratio adjustment in copying is performed. For the adjustment procedure, refer to the previous descriptions.
PAGE 12
Main code Sub code 50 18 Contents Duplex memory reverse position adjustment 50 19 Duplex rear edge void adjustment 51 2 Resist amount adjustment Details of operation After completion of warmup, shading is performed and currently set value is displayed 1 Shading data check Set range 58 1 ! 99 Key operation Memory reverse position adjustment value: Copy quantity keys After completion of warmup, shading is
PAGE 13
[8] USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. 1. List of user programs This copier has the following user programs. Program name Program No Description Default Parameters 0(OFF) 1(30sec) Auto clear time 1 Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made.
PAGE 14
Program name Program No Description Default Selects a pattern for 2 in 1 copying. Layout in 2 in 1 copy* Parameters 1(Pattern 1) 17 Pattern 1 2(Pattern 2) Selects a pattern for 4 in 1 copying. 1(Pattern 1) 2(Pattern 2) Layout in 4 in 1 copy* 18 Pattern 1 3(Pattern 3) 4(Pattern 4) Offset of paper output tray 19 Enables or disables the offset function of the paper output tray.
PAGE 15
[9] TROUBLE CODE LIST 1.
PAGE 16
Main code Sub code E1 11 Check and remedy Replace the E-Sort PWB. Check grounding of the machine. 12 Content E-Sort PWB CODEC error Detail E-Sort PWB CODEC error Cause A CODEC error is detected in the E-Sort PWB. Control circuit hung up due to noises CODEC peripheral circuit error 13 14 Detail of trouble Check and remedy Replace the E-Sort PWB. Check grounding of the machine.
PAGE 17
Main code Sub code E1 82 Check and remedy Check the connectors and harness of the E-Sort PWB and the MCU PWB. Check grounding of the machine. Check the ROM of the E-Sort PWB. 84 Content E-Sort PWB communication trouble (Framing) Detail Communication trouble between MCU and E-Sort PWB (Framing error) Detail of trouble Cause Check and remedy 88 E7 03 Sub code E7 03 04 E-Sort PWB connector disconnection E-Sort PWB MCU PWB harness failure E-Sort Motherboard connector pin breakage.
PAGE 18
Main code Sub code F2 04 F5 F6 02 00 Detail of trouble Content CRUM data read trouble Detail Communication error between CRUM PWB and MCU PWB Cause CRUM PWB data error MCU PWB error MCU PWB EEPROM error Disconnection between CRUM (toner cartridge) and MCU PWB Check and remedy Replace the toner cartridge. Replace MCU PWB. Replace MCU PWB EEPROM Check and fix connection between CRUM (toner cartridge) and MCU PWB.
PAGE 19
Main code Sub code F6 88 F9 00 10 80 Detail of trouble Content FAX control PWB communication trouble (Timeout) Detail Communication trouble between MCU and FAX control PWB (Timeout error) Cause Bad connection of FAX control PWB connector Defective harness between FAX control PWB and MCU PWB Motherboard connector pin breakage FAX control PWB ROM error/Data error Check and remedy Check connector/harness between FAX control PWB and MCU PWB. Check grounding of the machine.
PAGE 20
Main code Sub code F9 88 H2 H3 00 00 Detail of trouble Cause Printer PWB connector disconnection Printer PWB MCU PWB harness failure Printer PWB mother board connector pin breakage. Printer PWB ROM defect,data failure Check and remedy Check the connectors and harness of the printer PWB and the MCU PWB. Check grounding of the machine. Check the ROM of the printer PWB.
PAGE 21
Main code Sub code L4 01 10 Detail of trouble Check and remedy Check the main motor operation with SIM 25-1. Check the harness and the connector between the MCU PWB and the main motor. Content Job separator motor trouble Details When the home is not detected within 2.5 sec after the job separator tray starts to move upwards. Cause Main code Sub code U2 11 The job separator upper limit detection sensor is defective. The job separator motor is defective.
PAGE 22
Main code Sub code U9 00 80 81 82 84 Detail of trouble Cause Operation control PWB connector disconnection Operation control PWB MCU PWB harness failure Check and remedy Check the connectors and harness of the operation control PWB and the MCU PWB. Check grounding of the machine. Check the ROM of the operation control PWB.