DV-HR300U SERVICE MANUAL SX3L5DV-HR300 DVD VIDEO RECORDER MODEL DV-HR300U In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS Page 1. IMPORTANT SERVICE NOTES ........................................................................................................ 2 2. FEATURES ...................................................................................
DV-HR300U 1. IMPORTANT SERVICE NOTES This Unit is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear cover. This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. Note: This unit can be used only where the power supply is AC 110V-240V, 50/60Hz. It cannot be used elsewhere.
DV-HR300U IMPORTANT SERVICE NOTES etc.) and measure the AC voltage drop across the resistor. Reverse the AC plug on the set and repeat AC voltage measurements for each exposed part. Any reading of 0.45V rms (this corresponds to 0.3mA rms AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the VCR/DVD combination model to the owner.
DV-HR300U NOTES DE SERVICE IMPORTANTES pièces métalliques exposées ayant un parcours de retour au châssis (connexions d’antenne, coffret métallique, tétes de vis, boutons et arbres de commande, etc.) et mesurer la chute de tension CA entre la résistance. Inverser la fiche CA (une fiche intermédiaire non polarisée doit être utilisée à seule fin de faire ces vérifications.) sur l’appareil et répéter les mesures de tension CA pour chaque piéce métallique exposée.
DV-HR300U Precautions for using lead-free solder 1 Employing lead-free solder "Operation (R) PWB, Operation (L) PWB, Power PWB and UV PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper.
DV-HR300U 2. FEATURES z A new timer recording system:"Easy Recording Guide" » The Recorder is equipped with a high-capacity hard disc, so you'll have more chances than ever before for timer recording, and the new timer recording system makes this even easier. A schedule grid of times and channels is displayed on the screen, and by simply designating cells in the grid with the remote control, timer programming becomes as easy as circling your favorite shows in the newspaper.
DV-HR300U 4 Batch erasing of titles/chapters Titles and chapters which become unnecessary after editing can be batch erased by selecting them from the list of recordings (thumbnails). 5 Edit undo function*4 If you mistakenly erase data during editing, this function lets you restore it to its immediately preceding state, just like "Undo" on a PC, so you can edit worry-free. *4 Edit undo can only be used once. It only works when "DELETEDIT" is assigned to a colored button (green) displayed on the screen.
DV-HR300U LP (2X): Approx. 4 hours EP (3X): Approx. 6 hours MN (Manual): 32 levels between FINE and EP Playback Playable discs: DVD Video, DVD-R/RW, Audio CD (CD-DA), Video CD, CD-R/ RW (CD-DA, Video CD format, MP3 file format) Tuner Channel coverage: VHF 2-13 UHF 14-69 CATV 1-125 Timer Programs: 32 programs/1 year Clock: Quartz lock (12-hour digital display) Memory backup: Approx.
POWER STANDBY indicator TIMER indicator CHANNEL " /' PLAY/REC indicators (for HDD) PLAY/REC indicators (for DVD) 9 4 1 3 1 2 3 9 1 7 6 8 9 7 11 7 8 9 10 11 5 12 13 14 15 4 7 12 ● REC 13 REC STOP 14 REC PAUSE 15 HDD 16 DVD 17 | PLAY 18 ■ STOP/LIVE 19 STILL/PAUSE 16 17 18 19 6 DIGITAL AUDIO Output OPTICAL terminal 9 8 7 6 5 LINE IN 1 (AUTO REC) • AUDIO Input jacks • VIDEO Input jack • S-VIDEO Input jack LINE IN 2 • AUDIO Input jacks • VIDEO Input jack • S-VIDEO Input jack LINE OUT
» » » » » 2 Load the batteries. Load the two “AAA” size batteries (R-03, UM/SUM-4) supplied with the remote control unit. Make sure that the battery and poles are positioned as indicated. 3 Slide the battery cover in the direction of the arrow until it clicks. 10 Front 22.96ft. About 30ϒ About 30ϒ Remote control unit Remote sensor Operating range of remote control NOTE Do not subject the remote control unit to shock, water or excessive humidity.
DV-HR300U 5. DISASSEMBLY METHOD 5-1. DISASSEMBLY METHOD 1 (1) Removing the top cabinet 1. Remove five screws 1. 1 1 2. Slide back the top cabinet by 10 mm and remove upward. 1 (2) Removing the panel 1 1. Push a protruding part shown in a at the bottom with a screwdriver, etc. 2. Remove the tray decoration assembly (detach springs from four claws on the backside of the tray). a 3. Remove two screws 2 and spring. 4. Pull the panel to remove as detaching from the eight claws.
DV-HR300U 9 (6) Removing the DVD unit 1. Remove four screws 9. 2. Remove the DVD unit (with the angle) upward. 3. Disconnect cables including the flat cable and power cable. 4. Remove the gasket. (7) Removing the rear terminal board and fan 1. Detach the fan cable from the main unit. 2. Remove two screws 0. 3. Detach the fan and fan cover. 4. Remove a screw q, two screws (tuner) w and eight screws e 10 13 (terminals) 5. Pull the rear terminal board backward to remove.
DV-HR300U 5-2.
DV-HR300U 5-3. Notes for servicing 1. After replacing the HDD or main PWB, register the HDD-ID again. 2. After replacing I54R NOR flash (IC7502) or NAND flash (IC7509), upgrade the version using the CD. All the data in the HDD will be formatted by replacing the main PWB unit. The following parts cannot be replaced as the system information needs to be written. (Replace the PWB.) 1.
Reset Check YES NO NO NO 15 YES IC3502 pin 84 YCDEC_RST IC7304 pin 151 ENCRST IC4005 pin 1 DV_RST IC3009 pin 5 DACADC_RST IC3005 pin 13 AD_RST Is reset signal ("H" → "L" when reset) input to pins of each IC? IC4501 pin 54 SV_RST After power on, is reset signal ("H" → "L" when reset) input to IC4501 pin 54? YES Is serial communication established between IC7506 and sub unit IC501? IC7506 pin 34 FPCDOUT (SUBMIC_D_OUT) IC7506 pin 36 FPCSTB (SUBMIC_CS) IC7506 pin 38 FPCCLK (SUBMIC_CLK) IC7506 pin 39
YES Check following items. 16 YES Check following items. Communicating with drive via ATAPI? Access drive when CN4502 pin 4 CS0 and pin 3 CS1 are at "L" level. (Communication is ongoing if intermittently set at LOW.) CN4502 pin 6 DA0, pin 8 DA1, pin 5 DA2 and ATAPI register address (intermittently set at LOW). CN4502 pin 10 INTRQ is at "H" level when drive interrupts. Output after processing transfer command from IC7506, etc. CN4502 pin 20 DMARQ is at "L" level when drive requests data transfer.
YES NO NO Check IC7506 and peripheral circuits. Refer to Flow chart No.2 "Drive is not working properly (communication failure with IC7506)" or Flow chart No.3 "HDD is not working properly (communication failure with IC7506)". 17 NO Check IC7506 and peripheral circuits. Check lines between pins of IC7506 and CN3001 as well as circuits on lines.
1 YES IC2501 pin 10 COM_Y IC2502 pin 12 CB IC2502 pin 14 CR Is video signal input to each pin of IC2501? YES IC2502 pin 6 COM_Y IC2502 pin 5 CB IC2502 pin 3 CR YES Is video signal input to each pin of IC2502? IC2502 pin 8 OSD_Y IC2502 pin 11 OSD_PB IC2502 pin 16 OSD_PR Is video signal input to each pin of IC2502? YES Is video signal input to pins of IC2802 and 2801? IC2802 pin 8 OSD_Y IC2801 pin 3 OSD_PB IC2801 pin 5 OSD_PR YES NO NO NO NO NO YES Is video signal input to pins of sub uni
NO Check PROGRE (H) line. 19 NO NO Is PB signal output to D terminal (CN2401)? Is PR signal output to D terminal (CN2401)? NO NO NO NO NO Is Y signal output to component terminal (J2403)? Is PB signal output to component terminal (J2403)? Is PR signal output to component terminal (J2403)? Is Y signal output to D terminal (CN2401)? Is video signal output to each output terminal? YES IC2501 pin 20 COMPO_Y IC2501 pin 18 CB _OUT IC2501 pin 16 CR _OUT NO YES Check T_V_MUTE line.
Check SDRCLK line between IC3502 pin 17 and IC3503 pin 35. YES Is clock signal SDRCLK input to IC3503 pin 35? 20 YES Refer to Flow chart No.6/No.7 "Playback images do not appear properly".
NO 21 Is audio digital signal output to each pin of IC6501? IC6501 pin 3 VOUT_L IC6501 pin 5 VOUT_R YES YES Is audio signal output to pins of main unit connector CN3001? CN3001 pin 11 VOUT_L CN3001 pin 12 VOUT_R YES IC3009 pin 11 AUDIO_OUT_L IC3009 pin 10 AUDIO_OUT_R Is audio signal output to each pin of IC3009? YES Is system control signal output to each pin of IC3009? IC3009 pin 8 SPIDAO IC3009 pin 7 SPICLK IC3009 pin 6 DAC1_L YES YES Is audio digital signal output to each pin of IC3009? IC3009
YES 22 YES YES NO NO 1 YES IC3002 pin 13 AUD_L_ADIN IC3002 pin 3 AUD_R_ADIN Is audio signal input to each pin of IC3002? YES NO Is audio signal output to pins of main unit NO connector CN3001? CN3001 pin 8 AUD_L_ADIN CN3001 pin 7 AUD_R_ADIN IC6102 pin 1 INPUT_L IC6102 pin 7 INPUT_R Is audio signal output to each pin of IC6102? IC6102 pin 3 INPUT_L IC6102 pin 5 INPUT_R NO NO Check each control signal line. Check lines between pins of CN3001 and IC3002.
YES 23 Refer to Flow chart No.4 "Recording is impossible (MPEG stream check)". YES IC3008 pin 9 → IC7304 pin 7 AIN_ALRCK IC7304 pin 7 AIN_ALRCK IC7304 pin 9 AIN_ADAT IC3008 pin 12 → IC7304 pin 9 AIN_ADAT IC3008 pin 7 → IC7304 pin 8 AIN_ABCK NO Check lines between pins of IC3008 and IC7304. Check IC3008 peripheral circuits or replace IC3008. Check lines between pins of IC3005 and IC3008.
YES YES YES 24 YES Check or replace IC501 peripheral circuits. YES Is control voltage properly input to IC501 pin 87 and 88? YES Is key switch connected properly? Operation keys do not work. FLOW CHART No.16 Check display tube and main unit.
DV-HR300U -MEMO- 25
DV-HR300U DV-HR300U 7. BLOCK DIAGRAMS 7-1.
DV-HR300U DV-HR300U 7-2.
DV-HR300U DV-HR300U 7-3.
DV-HR300U DV-HR300U 7-4.
DV-HR300U DV-HR300U 8. SCHEMATIC DIAGRAMS J Note : 8-1.
DV-HR300U DV-HR300U 8-2.
DV-HR300U DV-HR300U 8-3.
DV-HR300U DV-HR300U 8-4.
DV-HR300U DV-HR300U 8-5.
DV-HR300U DV-HR300U 8-6.
DV-HR300U DV-HR300U 8-7.
DV-HR300U DV-HR300U 8-8.
DV-HR300U DV-HR300U 8-9.
DV-HR300U 8-10.
DV-HR300U 8-11.
DV-HR300U DV-HR300U å AND SHADED COMPONENTS=SAFETY RELATED PARTS 8-12.
DV-HR300U DV-HR300U 8-13.
DV-HR300U DV-HR300U 8-14.
MAIN PWB SIDE A J C3 0 1 9 D4 5 0 3 C3 0 1 8 C3 0 1 7 C3 0 1 6 R3 0 6 0 R3 0 6 4 I C3 0 0 5 C3 0 2 4 R3 0 5 8 R3 0 7 5 R3 0 5 7 T P3 5 T0 P3 2 501 R4 6 0 4T L 4 5 6 4 R4 6 0 1 C3 0 2 5 R4 6 2 5 C4 5 1 1 C4 5 0 9 R4 5 9 1 R4 5 8 9 R4 5 8 6 R4 5 8 4 I C3 5 0 1 R4 6 0 6 R4 6 0 5 R4 6 0 2 R4 6 0 3 R4 5 8 3 R3 0 7 6 R3 0 7 2 R3 1 3 3 R3 1 3 2 R3 0 5 1 C3 5 0 2 R3 5 0 2 R3 6 2 6 R3 6 2 7 C3 5 0 8 C3 5 0 4 C3 5 0 6 R3 5 0 4 C4 5 2 0 F B4 5 0 6 R3 0 2 5 R3 0 2 6 F B3 5 0 7 R3 0 2 2 R3 0 2
1 2 3 4 62 5 6 7 8 9 10 R7 6 7 3 C7 5 0 4 11 F B3 0 1 8 F B3 0 1 9 R7 8 1 9 12 CN3 0 0 2 C3 0 3 8 13 14 C4 0 3 0 CN3 0 0 4 15 R7 3 6 4 C7 5 4 4 R7 6 2 8 R7 6 2 9 R7 6 3 0 C4 0 5 2 C7 5 4 1 R4 1 4 4 R4 1 4 5 R4 1 4 2 R4 1 4 3 R4 0 5 9 R4 0 5 8 R4 0 5 7 R4 1 3 6 R4 1 3 7 R7 6 5 8 R7 7 9 8 R7 6 1 3 R4 1 3 0 R4 1 3 1 C3 0 4 0 R4 0 4 1 R4 0 4 2 R4 0 4 3 R4 0 4 4 R4 0 4 5 CN4 5 0 1 R4 0 5 2 16 63 R4 5 4 0 R4 5 3 9 R4 5 3 8 F B4 0 0 8 R4 0 5 5 F B4 0 0 9 R4 0 5 3 R4 0 5 1 17
DV-HR300U DV-HR300U SUB PWB SIDE A J I H G F E D C B A 1 2 3 4 64 5 6 7 8 9 10 11 12 13 14 15 16 65 17 18 19
DV-HR300U DV-HR300U SIDE B J I H G F E D C B A 1 2 3 4 66 5 6 7 8 9 10 11 12 13 14 15 16 67 17 18 19
DV-HR300U OPERATION (R) PWB SIDE A SIDE B J I H G F E D C B A 1 2 3 4 5 6 68 7 8 9 10
DV-HR300U OPERATION (L) PWB SIDE A SIDE B J I H G F E D C B A 1 2 3 4 5 6 69 7 8 9 10
DV-HR300U POWER PWB SIDE A J I H G F E D C B A 1 2 3 4 5 6 70 7 8 9 10
DV-HR300U SIDE B J I H G F E D C B A 1 2 3 4 5 6 71 7 8 9 10
DV-HR300U UV PWB SIDE A J I H G F E D C B A 1 2 3 4 5 6 72 7 8 9 10
DV-HR300U SIDE B J I H G F E D C B A 1 2 3 4 5 6 73 7 8 9 10
DV-HR300U LCD PWB J SIDE A I H G F E SIDE B D C B A 1 2 3 4 5 6 74 7 8 9 10
DV-HR300U 10. REPLACEMENT PARTS LIST/ Part No. ★ Description Code EXPLODED VIEWS Ref. No. ELECTRICAL PARTS LIST Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Les pièces marquéss " å " sont importantes pour maintenir la sècurité de l'appareil.
DV-HR300U Ref. No. Part No. ★ Description Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Code Ref. No.
DV-HR300U Ref. No. ★ Part No. Description Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Code Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Code Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Code Ref. No.
DV-HR300U Ref. No. ★ Part No. Description Ref. No.
DV-HR300U Ref. No. ★ Part No.
DV-HR300U Ref. No. Part No. ★ Description Ref. No.
DV-HR300U Ref. No. Part No.
DV-HR300U Ref. No. ★ Part No. Description Ref. No.
DV-HR300U Ref. No. ★ Part No. Description Code Ref. No.
DV-HR300U Ref. No. ★ Part No. Description Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Code Ref. No.
DV-HR300U Ref. No. Part No. ★ Description Ref. No.
DV-HR300U CABINET EXPLODED VIEW 24 A H 70 44 28 66 M A G 1 60 G 18 46 L 61 70 K 40 G D 24 66 I H 9 J 59 A 45 33 24 10 34 F 58 E 43 7 38 32 57 R 56 F 55 41 29 M 4 12 E P J P Q K 15 L 32 51 32 A 3 29 54 53 9 17 Q 50 S N H I 52 63 D 37 A 23 N C 69 39 2 32 16 65 C E 22 A B D 25 13 64 R 67 8 32 32 20 27 B 68 32 36 5 32 35 68 19 F C B 600 21 62 30 26 32 31 6 A 30 14 32 S 1 2 3 4 93 5 6
DV-HR300U FRONT PANEL EXPLODED VIEW H G 600 600-15 F 600-1 600-13 E 600-6 600-11 600-8 600-9 600-4 600-17 600-7 600-10 D 600-3 600-5 600-2 600-14 C 600-12 600-16 B A 1 2 3 4 94 5 6
DV-HR300U 11.
DV-HR300U COPYRIGHT © 2004 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. TQ1657-S Jan. 2004 Printed in Japan In Japan gedruckt Design and Production Information Design : JAPAN Production : SMM SA.