User Manual

SETUP
–
7
–
EN
21. MAIN (AC power cord)
Connect to a standard AC plug.
22. COMPONENT VIDEO OUT Jacks (DVD only)
Connect optional component video cable here through the com-
ponent video input jacks of a TV.
23. COAXIAL DIGITAL AUDIO OUT Jack (DVD only)
Connect to a compatible Dolby Digital receiver.
Use to connect to a Dolby Digital, DTS, or MPEG decoder.
24. AUDIO OUT Jacks (Analog Left/Right) (DVD only)
Connect to the audio input jacks of A/V-compatible TV.
25. S-VIDEO OUT Jack (DVD only)
Use the S-video cable to connect this jack to the S-video input
jack on your A/V-compatible TV or wide screen TV for a higher
quality picture.
26. EURO AV1 (TV) Terminal
Use the scart cable to connect this terminal to the 21-pin scart
terminal on your A/V-compatible TV or wide screen TV for a best
quality picture.
If your TV has RCA type audio and video input jacks, you may con-
nect to this terminal through the SCART output adaptor (sup-
plied).
27. EURO AV2 (DECODER) Terminal (VCR only)
Use the scart cable to connect this terminal to the 21-pin scart
terminal on your decoder.
28. RF OUT Jack
Use the supplied Round Coaxial cable to connect this jack to the
AERIAL jack on your TV.
29. AERIAL Jack
Connect your antenna, cable box or direct broadcast system.
AERIAL
RF OUT
28 2926 27252422 2321
PULL OPEN
DV-NC200
OPERATE
OPEN/CLOSE
PLAYST OP
DVDVCRCH
TIMER
RECPLAYREW FF
ST OP/
EJECT
(TRACKING)
OUTPUT
1 2 3
6
54
7
0
+10
8 9
TAPE SPEED
/SYSTEM
DIRECT SKIP
QUICK-FIND
TIMER
ON/OFF
CH
SLOW
SEARCH MODE
GAMMA
MENUTITLE
STILL/PAUSE
REC/OTR
STOP
PLAY
FWD
REV
RETURN
SKIP
REPEAT
A-B REPEAT
CLEAR/C-RESET
ENTER
ZOOM
AUDIO
VCR
MARKER
DVD
MODE
SETUP
SUBTITLE
OPEN/CLOSE
EJECT
ANGLE
DISPLAY
OPERATE
VCR/DVD COMBINATION
NA545FD
VCR
OUTPUT
DVD
OUTPUT button
DVD OUTPUT
indicator
VCR OUTPUT
indicator
DVD button
VCR button
VCR/DVD SWITCHING
Display During Operation
No disc inserted / cannot read disc.
Appears when a disc is loaded on the
disc tray.
Appears when the disc tray is opening.
Appears when a disc or tape is being
played back.
Appears when the disc tray is closing.
Appears when the PBC function is acti-
vated. (Video CD playback only. Refer
to page 5.)
Rear Terminals
Because this product is a combination of a VCR and a DVD player,
you must select first which component you wish to operate with
OUTPUT.
VCR MODE
Press VCR on the remote control.
(Verify that the VCR OUTPUT indicator is lit.)
DVD MODE
Press DVD on the remote control.
(Verify that the DVD OUTPUT indicator is lit.)
Hint
• Pressing only OUTPUT on the front panel DOES NOT switch the
mode of the remote control. You MUST select the correct mode
on the remote control.
In the wrong mode, the VCR/DVD does not respond to your com-
mands correctly. Before starting your desired operation, select
the correct mode by following the instruction (
VCR/DVD COMBINATION
NA527AD
1 2 3
6
54
7
0
+10
8 9
STOP
PLAY
VCR
DVD
press first.
or
VCR/DVD COMBINATION
NA527AD
1 2 3
6
54
7
0
+10
8 9
STOP
PLAY
VCR
DVD
press first.
) under the subject heading.