CONTENTS CONTENTS PRODUCT SPECIFICATIONS SAFETY INSTRUCTIOS OPERATION SERVICE AND MAINTENANCE PARTS LIST – DELUXE SLASHER 1 2 2 8 9 12 [1]
PRODUCT SPECIFICATIONS Product No.
SAFETY INSTRUCTIONS Uses: Perfect for hobby farms ~ fence-line and wall edge slashing ~ slashing grasses, small trees and light scrub ~ perfect is rough terrain ~ cleaning roadsides ~ creating firebreaks.
SAFETY INSTRUCTIONS 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. Before using the Slasher, read and ensure you understand the contents of this Safety and Operator’s Manual for the associated implement. Note all the safety instructions. Never allow an improperly trained person, children or anyone who is not familiar with the safety rules and operating instructions to attach or operate the slasher.
SAFETY INSTRUCTIONS 1.4 Maintenance Safety 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. Follow good shop practices. Keep service area clean and dry. Be sure electrical outlets and tools are properly grounded. Use adequate light for the job at hand. Make sure there is plenty of ventilation. Never operate the engine in a closed building. The exhaust fumes may cause asphyxiation.
SAFETY INTRUCTIONS 1.5 Safety & Model Decal The position of safety decals are shown in the illustrations below. Good safety requires that you familiarize yourself with the various safety signs, and increase your SAFETY AWARENESS.
SAFETY INSTRUCTIONS [7]
OPERATION 2.1 Installation Line up the lower linkage arms with the linkage pins of the slasher, slide the linkage arms onto the pins and secure with a lynch pin. Attach the top link to the slasher. Raise the slasher from the ground and adjust the stabilizer bars or chains to allow minimal sideways movement. To disconnect the slasher, lower the slasher to the ground and reverse the above procedure.
OPERATION 2.2 General Operation The Cutting Height Adjustment: The cutting height can be set by lifting the slasher, undoing the bolts and nuts attaching the adjustable skids and repositioning the skid plates to the required height. When adjusting the skids, ensure the whole wear surface touches the ground to avoid uneven wear. Achieve this by adjusting the skids retighten the attaching bolts and nuts securely.
SERVICE AND MAINTENANCE 2. 3. Gear Box Oil: Use SAE 90 Gear oil: Storing Lubricants: Your machine can operate at top efficiency only if clean lubricants are used. Use clean containers to handle all lubricants. Store them in an area protected from dust, moisture and other contaminants. 3.1.2 1. 2. 3. 4. GREASING Use a hand-held grease gun for all greasing. Wipe grease nipple with a clean cloth before greasing, to avoid injecting dirt and grit. Replace and repair broken nipples immediately.
SERVICE AND MAINTENANCE 8hrs/Daily Lubricate PTO Shaft Lubricate jockey Wheels Lubricate Blade Spindle x x x Check Gear Box Oil Level x x x Annually x x x x Clean Machine Lubricate and PTO Shaft Cover 3.2.4 40hrs/Weekly x x x PTO SHAFT MAINTENANCE The PTO shaft is designed to telescope to allow for dimensional changes as the machine goes through its operating range. A tubular guard encloses the driving components and is designed to remain stationery on a turning shaft when required.
SERVICE AND MAINTENANCE 3.3 STORAGE After the season’s use, the machine should be thoroughly inspected and prepared for storage. Repair or replace any worn or damaged components to prevent any unnecessary down time at the start of next season. To ensure a long, trouble free life, follow the procedure outlined below: 1. Thoroughly wash the machine using a pressure washer to remove all dirt, mud, debris and residue. 2. Inspect the blades and rotor for damage or entangled material.
PARTS LIST – Deluxe Slasher Deluxe Slasher Assembly parts No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Name & Specifications Wheel assembly Pin R pin Locking nut M16 Plain washer 16 Bolt M16x45 Gearbox Clutch Guard Swivel Pin Split pin 2.
PARTS LIST – Deluxe Slasher Deluxe Slasher Assembly parts No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Name & Specifications Wheel assembly Pin R pin Locking nut M16 Plain washer 16 Bolt M16x45 Gearbox Clutch Guard Swivel Pin Split pin 2.
PARTS LIST – Deluxe Slasher Wheelkit Assembly parts Wheel Kit Assembly parts No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Name & Specifications Wheel bracket weldment Wheel fork lock ring Nut M12 Bolt M12x45 Wheel fork Locking nut M16 Plain washer 16 Dust cap Oil seal seat Oil seal W25x40x5 Bearing 6203 Bolt M10x30 Boss hub nave Wheel rim Axle Type Spring lock washer 10 Nut M10 SL1200H – SL1800W Qty 1 1 1 1 1 2 2 2 2 4 2 4 1 2 1 1 4 4 SL1200H Part NO. HM3FT6.00.017 HM5FT.00.
PARTS LIST – Deluxe Slasher Wheel Kit Assembly parts No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Name & Specifications Wheel bracket weldment Wheel fork lock ring Nut M12 Bolt M12x45 Wheel fork Locking nut M16 Plain washer 16 Dust cap Oil seal seat Oil seal W25x40x5 Bearing 6203 Bolt M10x30 Boss hub nave Wheel rim Axle Type Spring lock washer 10 Nut M10 SL1200H – SL1800W Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 SL1200H Part NO. HM5FT.00.017 HM5FT.00.208 GB 6170-86 GB 5783-86 HM5FT.00.