DV-SL700W SERVICE MANUAL No. S9501DVSL700W DVD PLAYER MODEL DV-SL700W • In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS Page SAFETY PRECAUTION FOR SERVICE MANUAL ............................................................................................................... 2 AC POWER SUPPLY CORD.............................................................
DV-SL700W SAFETY PRECAUTION FOR SERVICE MANUAL l This product is classified as a CLASS 1 LASER PRODUCT. l WARNINGS: The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class 1 Requirements. However, the following precautions must be observed during servicing to protect your eyes against exposure to the Laser beam.
DV-SL700W SPECIFICATIONS As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
DV-SL700W LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against Do not look directly at the laser beam coming your skin. from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30cm away from the pickup lens when the diode is turned on.
DV-SL700W STANDARD NOTES FOR SERVICING (1) Using desoldering remove the solder from all Using lead-freebraid, wire solder pins of the flat pack-IC. When you use solder flux When fixing the PWB soldered thepack-IC, lead-freeyou solder, which is applied to all pins of with the flat can apply lead-free wire solder. Repairing with conventional remove it easily. (Fig. S-1-3) lead wire solder may cause damage or accident due to cracks.
DV-SL700W How to Remove / Install Flat Pack-IC (4) Bottom of the flat pack-IC is fixed with glue to the With Soldering Iron: 2. Installation (1) Using desoldering braid, remove the solder from all (1) pins Usingofdesoldering braid, remove the use solder from flux the the flat pack-IC. When you solder foil of each pin oftothe onpack-IC, the CBAyou so you which is applied all flat pinspack-IC of the flat can can install a replacement flat pack-IC more easily. remove it easily. (Fig.
DV-SL700W (4) Bottom of the flat pack-IC is fixed with glue to the Instructions for Handling CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat Semi-conductors up. Then remove (glue will be melted). (Fig. S-1-6) Electrostatic breakdown of the semi-conductors may (5) Release flat pack-IC fromcaused the CBA tweeoccur due to athe potential difference by using electrostatic zers. (Fig. S-1-6) charge during unpacking or repair work. Note: 1.
DV-SL700W OPERATING CONTROLS AND FUNCTIONS n Main unit (front panel) 1 2 3 4 5 6 7 8 1. Disc Tray 5. Disc Tray OPEN/CLOSE Button 2. STANDBY Indicator 6. Play or Pause Button 3. PLAY/PAUSE Indicator 7. STOP Button 4. Remote Sensor 8. ON/STANDBY n Main unit (rear panel) 1 2 3 4 5 6 1. AC Cord Lead 4. Digital Output Socket(Coaxial) 2. Component Video Output Sockets 5. Audio Output Sockets 3. Video Output Socket 6.
DV-SL700W n Remote control 1. Remote Control Transmitter 2. MENU/PBC Button 3. Disc Tray Open/ Close Button 4. Title Select Button 5. Fast Backward/Chapter (track) skip down 11 6. Fast Forward/Chapter (track) skip up 5 12 13 7. Direct Number Buttons 6 14 8. PROGRAM / ANGLE Button 9. MUTE Button 1 2 3 4 10 15 7 8 9 10. ON/STANDBY Button 16 11. SETUP/GO TO Button 17 18 12. SLOW Button 19 13. STOP Button 20 21 14. ENTER / PLAY / PAUSE Button 15.
AC~110-240V POWER LOADER M07S STANDBY P+5V GND P+12V SUNPLUS SHPE8202D Figure 1: BLOCK DIAGRAM 10 8550SS +1.8V 8550SS +3.3V MOTOR AM5869 RESET CM3403-29SO SDRAM 512X16X2 IR KEY LED EEPROM AF24BC02 FLASH MX29LV040T C-70 SPDIF OUT Y.U.
1 G 2 62PIN 63PIN 3 11 4 Figure 1: CONTROL PCB SCHEMATIC GND LED2 LED3 5 R204 1K Q302 2SA733 R208 4.7K R207 10K R202 560 D102 D103 D104 D105 1N4148 1N4148 1N4148 1N4148 IR VCC CS DATA CLK Q301 2SA733 R201 560 C12 104 1N4148 D203 ON/STD BY TA202 EJECT TA201 C 8 7 6 5 4 3 2 1 R203 1K F R209 4.
DV-SL700W MAIN PCB SCHEMATIC A B Pickup head parameter Sony Motor Driver AM5668 Motor Driver AT5660 R40 R39 R14 R15 R53 R62 C32 R63 C33 4.7 4.7 100 100 20K 12K 1500P 68K 1000P R62 3.3K C32 R63 C33 2700P 39K 1000P Sanyo 5.1 5.1 0 0 2.2K 33K 1000P 68K 1000P 20K 1000P 39K 1000P Samsung 5.1 5.1 0 0 2.2K 12K 1500P 68K 1000P 3.3K 2700P 39K 1000P Mitsumi 5.1 5.1 0 0 2.2K 12K 1500P 68K 1000P 3.3K 2700P 39K 1000P C DVCC33 VCC1.
DV-SL700W MAIN PCB SCHEMATIC RF3.3V C112 C113 C114 0.1UF 0.1UF 0.1UF TV0 TV3 TV4 TV CVB Y Cb C CVB CVB Y CVB (S-Video) G C (S-Video) R B GND PLL3.3V VVCC3 107 C108 C109 C110 1UF 0.1UF 0.1UF 0.1UF GND DAC_REF C153 C111 + 10UF16V VGND 0.1UF GND C163 GND R109 C154 GND 680PF C159 1UF 1.5K 0.
DV-SL700W MAIN PCB SCHEMATIC A R SPDIF_OUT 10 TV3 B TV4 TV5 Cb Cr Y Y C CVB deo) B G ZD301 (S-Video) R 6.8V VCC ZD304 6.8V VCC VGND VVCC3 C VGND C171 NCV_BIAS C115 0.1UF R302 75 OHM ZD306 VGND 6.8V VCC R303 ZD307 6.8V 75 OHM ZD303 6.8V VGND V_COMP 0.1UF V_REF 0.1UF V_FSADJ 390 C117 VGND R137 VGND ZD302 6.
DV-SL700W MAIN PCB SCHEMATIC VCC VGND R303 VGND VGND M R304 75 OHM VGND VGND L302 2.4UH C303 470PF VGND C307 470PF VGND C304 L304 470PF 2.
DV-SL700W GND FORVH WR FRQQHFWRU A D101 1N4148 D102 1N4148 GND GND DVDLDO MAIN PCB SCHEMATIC DIP28-SSOPH 1 FCO TRB1 2 REGO3 3 25K IC105 AM5869S 10K VINFC BIAS + C125 GND 26 VREF2 27 0.
DV-SL700W MAIN PCB SCHEMATIC 16 17 18 GND 19 20 DVDLDO 21 CDLDO C182 47UF16V 22 DVDMDI 23 CDMDI 24 RF3.3V 25 C122 0.1UF VREF1 GND R163 33K (1%)26 GND VREF2 27 C188 0.22UF 28 + C121 C183 C161 0.01UF 29 GND 0.1UF C162 0.01UF 30 47UF16V 31 RFCT RFCT TP5 C186 0.047UF 32 33 C184 300PF SBAD C187 820PF 34 FEO 35 GND R160 NG TEO 36 C210 0.1U GND C213 330PF 37 XOPVIP1 GND 38 XOPVIN1 39 XOPOP1 40 TCO GND 41 C211 1000PF GND RF3.3V R175 68K 42 C212 1000PF FCO R111 33K 43 44 GND 45 TRAYIN 46 TRAYOUT C127 0.1UF R176 2.
DV-SL700W MAIN PCB SCHEMATIC A _ M_D5 M_D4 M_D3 VDD_O2 M_D2 M_D1 M_D0 M_WE_B M_CAS_B M_RAS_B VSS_O2/VSS_K2 M_CS0_B/GPIO M_BA0 M_D15 M_D14 M_D13 VDD_K2 M_D12 M_D11 M_D10 B RD6 RB105 8 VCC1.
DV-SL700W MAIN PCB SCHEMATIC R420 1K SC2 L-OUT 7 F R433 47k +12V R-OUT Q406 2N3906 1 1 2 2 1 2 FB405 1 2 3 4 NC C431 NC POWER OFF C430 NC C432 NC NC SC-R IN 1 SC-L IN A16 A15 A14 A13 A12 A11 A9 A8 WE# NC NC NC A18 A7 A6 A5 A4 A3 A2 A1 SST 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 A17 GND NC A19 A10 DQ7 DQ6 DQ5 DQ4 VCC VCC NC DQ3 DQ2 DQ1 DQ0 OE# GND CE# A0 RA11 RA17 RA9 RA8 RA19 RA13 RA10 RA14 RD7 RA17 RD6 RWE RD5 FLASH_POWER RD4 RA18 FLASH_POWER RA16
DV-SL700W POWER PCB SCHEMATIC ! A F1 LF1 T250V/1A CX1 0.1uF/250V ! D1 1 1N4007 R1 470K D3 B ! N L C D2 R2 470K T1 1 R5 820K ! D4 C1 15uF/400V CON1 ! R5 100K C2 4700PF/1KV R6 820K D5 FR107 4 8 8 4 Q1 03NK60 Ac Power Supply Cord AC 110 ~ 240 V 50/60Hz 10 10 11 11 0.001UF/100V C4 R13 4.7K Q2 PMBS3906 R10 470R C6 103/50V 5 12 12 R7 39K R8 560R D7 1N4148 D 5 2 Q5 PMBS3904 2 ZD3 18V R12 10K R16 R17 R14 R4 4.7R 4.7R 4.7R 4.7R E C3 0.
DV-SL700W 1 2 3 4 5 6 7 8 R30 680 PC1-1 R37(JUMP) R36 1M A1015 Q7 R38 C11 0uF/16V Q8 47UF/16V R33 10.70K R31 1K R32 10K V+ V-24V +12V GND +5V PCON S+5V C16 1UF/50V U1 TL431 R33 10.0K R25 750R 1K Q6 C1815 C7 220uF/16V 1N5822 D14 L2(3uH) R27 10R C19 00PF/100V 7 C13 1500uF/100V 8 300R R28 ZD4 C14 470uF/10V 6.
DV-SL700W IC’S PIN VOLTAGE CHART IC101(SPCA8202D) Ref.number Mode 1 2 3 4 5 6 7 8 9 10 11 12 play 0.94 0.95 0.42 2.09 0.95 2.1 2.1 2.1 2.1 2.2 2.2 2.2 stop 0.94 0.95 0.44 2.09 0.95 2.1 2.1 2.1 2.1 2.2 2.2 2.2 13 14 15 16 17 18 19 20 21 22 23 24 play 2.47 1.5 1.5 2.45 1.7 0 0 3.3 2.46 0.19 0.19 3.3 stop 2.47 1.5 1.5 2.45 1.7 0 0 3.3 2.46 0.19 0.19 3.3 25 26 27 28 29 30 31 32 33 34 35 36 play 2.1 1.67 1.7 1.53 1.
DV-SL700W 169 170 171 172 173 174 175 176 177 178 179 180 play 0.3 2.7 0 1.25 3.3 1.26 0 2.88 1.67 0 1.66 1.67 stop 0.9 2.27 0 0 0 0 0 2.88 1.67 0 1.66 1.67 181 182 183 184 185 186 187 188 189 190 191 192 play 0.62 3.3 0.6 0.6 0.59 1.21 0.52 3.29 0 3.29 0 1.07 stop 0.62 3.3 0 0.6 0.59 1.21 0.52 3.29 0 3.29 0 1.08 193 194 195 196 197 198 199 200 201 202 203 204 play 1.17 3.29 1.2 0 3.26 0.03 2.64 1.67 1.67 1.
DV-SL700W stop 3.27 0 0.14 0.1 0.1 0 0 0 0 1.25 1.6 2.55 37 38 39 40 41 42 43 44 45 46 47 48 play 0 3.27 1.3 1.39 0 1.4 1.4 3.27 1.39 1.25 0 1.49 stop 0 3.27 0.24 0.22 0 0.22 0.22 3.27 0.19 0.18 0 0.16 49 50 play 1.13 0 stop 0.18 0 IC402(AZ4558) Ref.number Mode 1 2 3 4 5 6 7 8 play 0 0 0 -11.53 0 0 0 11.82 stop 0 0 0 -11.53 0 0 0 11.82 1 2 3 4 5 6 7 8 play 0 0 0 0 3.3 3.33 0 4.88 stop 0 0 0 0 3.3 3.
DV-SL700W WAVEFORMS WF1 VIDEO OUT Video Out WF3 WF3 0.5V 20us 0.2V 0.2V 20us Note : Note :~ WF3 : Power On (Stop) Mode. WF1 WF1 ~ WF3 : Power On (Stop) Mode. WF4 ~ WF7 : DVD Test Disc TDV-540A. WF4 ~ Bar WF775%) : DVD Test Disc TDV-540A.
DV-SL700W WF8 WF8 COMPONENT VIDEO OUT - Pr/Cr Output COMPONENT VIDEO OUT - Pr/Cr Output (Interlace mode) (Interlace mode) WF9 WF9 P-Scan Mode Pr level :525mV+10% 20us Interlace Mode Pr level :525mV+10% 20us WF10 Audio Left WF11 WF10 Audio Left WF11 Audio-L 2 + 0.2Vrms WF12 Rf Signal WF12 Rf Signal COMPONENT VIDEO OUT - Pr/Cr Output COMPONENT (P-Scan mode)VIDEO OUT - Pr/Cr Output (P-Scan mode) Audio Right Audio Right Audio-R 2 + 0.2Vrms Note : WF8 ~ WF9 : DVD Test Disc TDV-540A.
DV-SL700W -MEMO- 27
DV-SL700W OVERALL WIRING CONNECTION Standard Notes Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. WARNING A Many electrical and mechanical parts in this chassis have special characteristics.
DV-SL700W Standard Notes Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
1 2 SW1 3 30 2 Figure 1: WIRING SIDE OF POWER PCB (TOP VIEW) 4 BR BL HS1 AC POWER SUPPLY CORD AC 110 ~ 240V, 50/60Hz N L 1 2 1 THERE IS A HI-POT AREA DE MEME TYPE C1 C4 Q1 D5 C2 CY3 PC1 D12 LVP202350-0403 REV:A T1 TYPE AND RATING OF FUSE.
DV-SL700W WIRING SIDE OF POWER PCB (BOTTOM VIEW) A B C D E F G When servicing, pay attention as the area closed by this line ( ) is directly connected with AC.
DV-SL700W WIRING SIDE OF MAIN PCB (TOP VIEW) OUTPUT CONNECTION TABLE AUDIO OUT PB PR 5 D404 R418 R433 R313 C309 R408 R306 R410 Q308 R309 R409Q305 R308 R312 R185 R407 R105 R184 RB111 FB903 FB132 IC103A C936 R305 R307 Q401 R412Q307(NC) Q402R414 R311 R413 R151 RB106 A RB114 R163 C161 C184 C213 C938 C182 XT1 C941 R116 R166 R149 R150 R901 R R907 Q90 R147 A Figure 2: WIRING SIDE OF MAIN PCB (TOP VIEW) 1/2 32 RB102 C153 IC101 100 R115 40 82 4 2 C181 3 R4 C186 C2 RB115 R170 R167
DV-SL700W WIRING SIDE OF MAIN PCB (TOP VIEW) TO POWER PCB 6 5 4 CN901 WH (P) WH (P) WH (P) CON2 FB902 FB405 RB110 FROM 140 120 CD CHANGER RB116 C938 XT1 R901 A 40 C941 R907 Q901 R147 20 R115 A R163 C161 C184 C213 RB115 R170 R167 R177 C198 R905 1 R16 C186 C21 80 FROM CD CHANGER RB113 RB114 IC101 100 RB117 C160 C170 C154 R110 R164 R156 FB132 C123 R159 R157 R155 60 C916 C215 R161 R116 R166 R149 R150 180 R114 CN102 FB903 R305 R307 Q401 R412Q307(NC) Q402R414 R311 R413 R15
DV-SL700W FB305 C315 C177 A C118 C231 WIRING SIDE OF MAIN PCB (BOTTOM VIEW) C115 C109 C920 C110 C171 FB303 C116 C101 IC401B C194 C131 R135 C412 RB107 C239 FB308 C195 C234 C311 FB309 E F C218 C413 C327 C235 R437 FB404 R421 C921 C236 R411 G ZD309 H 1 2 C102 C108 C191 C111 C238 ZD305 R304 C312 D C188 C162 C179 C913 C310 C313 L310 IC104 R906 C232 FB918 C C122 C113 C163 C411 C410 TP11 C112 C316 FB402 C230 B C166 C165 C314 C120 3 4 Figure 2: WI
DV-SL700W WIRING SIDE OF MAIN PCB (BOTTOM VIEW) C125 C126 R175 C212 C127 R176 R903 C202 R902 C203 R148 R904 C939 R173 C940 C208 C207 C206 C132 FB134 C103 C102 C107 C106 C136 C134 R174 C201 R104 C199 R187 C130 C907 C104 C200 R171 C925 R103 R908 C912 C216 C217 T30 R142 R141 C105 C145 9 8 7 6 5 4 3 2 1 FB919 FB912 C219 R178 C911 FB137 C129 IC104 C209 C204 C205 FB136 C904 C188 C162 C179 C187 C114 C210 C904 C121 C211 R111 C905 C128 TP4 C124 C143 C135 C133 C141
DV-SL700W WIRING SIDE OF CONTROL PCB (TOP VIEW) JW106 TA204 TA202 B GND1 LUG WIRE (GND1) TO POWER PCB GND2 A D C14 SN201 JW104 GND3 TA201 GND4 TA203 C G CST WH WH (P) WH (P) WH (P) WH (P) WH (P) WH (P) WH (P) CN 105 TO MAIN PCB JW102 JW103 RB201 D202 DP2150/2151 Control Board RED LED F JW101 JW105 D201 GREEN LED C13 E 8 7 6 5 4 3 2 1 H 1 2 3 4 Figure 3: WIRING SIDE OF CONTROL PCB (TOP VIEW) 36 5 6
DV-SL700W WIRING SIDE OF CONTROL PCB (BOTTOM VIEW) A B C Q302 R202 R208 R204 R207 R209 R201 E Q301 R203 D101 C12 D F R101 D204 D203 D105 D104 D103 D102 G H 1 2 3 4 Figure 3: WIRING SIDE OF CONTROL PCB (BOTTOM VIEW) 1/2 37 5 6
DV-SL700W WIRING SIDE OF CONTROL PCB (BOTTOM VIEW) A B C D E F G H 1 2 3 4 Figure 3: WIRING SIDE OF POWER PCB (BOTTOM VIEW) 2/2 38 5 6
DV-SL700W NOTES ON SCHEMATIC DIAGRAM l Resistor: To differentiate the units of resistors, such symbol as K and M are used; the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. l Schematic diagram and Wiring Side of P.W. Board for this model are subject to change for improvement without prior notice.
DV-SL700W TROUBLESHOOTING Severe hum or noise is heard • Check that the connecting cords are away from a transformer or motor. • Move your TV away from the audio components. • The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. • Clear the disc. If you experience any of the following difficulties while using the system, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest service center.
DV-SL700W IC PIN FUNCTION DESCRIPTIONS IC105 5 Channel BTL Driver for DVD PLayer 19 Vcc2 18 VOLD- 17 VOLD+ 16 VOTK- 15 VOTK+ VOTR+ 10 VOSL+ 11 12 VOSL- VOFC- 13 VOFC+ 14 20 OPIN 21 VCTL 22 GND 23 VINLD 24 OPOUT 25 TRB_2 26 VINTK 27 BIAS 28 MUTE Pin Configuration: 6 7 8 9 FWD REV Vcc1 VOTR- REGO1 5 VINSL+ 4 2 TRB_1 REGO2 3 1 VINFC AM5869S Pin Description: PIN(S) NAME PIN No Pin Name 1 VINFC DESCRIPTION Function Input for focus driver 2 TRB_1 connect to external
DV-SL700W IC105 5 Channel BTL Driver for DVD PLayer Tray driver logic input: FWD(pin6) REV(pin7) VOTR+(pin10) VOTR-(pin9) Function L L OPEN OPEN Open mode L H L H Reverse mode H L H L Forward mode H H L L Brake mode Input circuit of pin6 and pin7 is designed to avoid simultaneous activation of upper and lower output tr.; however, in order to improve reliability, apply motor forward/reverse input once through open mode. We recommend time period for open longer than 10msec.
DV-SL700W PC1, Optical Sensor (EL-817) Pin Configuration: Pin No. And Internal Connection Diagram 1 4 2 3 1. Anode 3. Emitter 2. Cathode 4.
DV-SL700W IC101, DVD SINGLE CHIP MPEG A/V PROCESSOR IC101 SPHE8202(D)-216PIN 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 18
DV-SL700W Signal Description: VSS_* System Interface Audio analog output interface LPFOLPFN VDD_* CLKIN / CLKOUT RSTB VREFO PDPLT FDPLT DAC_VREF LPFNIN LGIN REI DAC_L DAC_R CNIN SLVL GMRES AU_XCK Audio digital output interface AGCCAP RFAP AU_BCK AU_LRCK RFO FLTIP FLTIN AGCON AGCOP AU_DATA[3:0] A_IEC_TX RFIP RFIS RFSUM ROM/flash interface SDRAM interface DPDA DPDB DPDC DPDD DVDA DVDB DVDC DVDD R_CS_B[3:0] R_OE_B CDB CDA CDF CDE DVDLDO R_WE_B R_A[19.0] R_D[7.
DV-SL700W Table 1 8202D Pin Description Pin No I/O AGCON Name 1 O Differential AGC output #N Definition AGCOP 2 O Differential AGC output #P RFIP 3 I Differential RF input #P RFIS 4 I Single-ended RF equalizer input. RFSUM 5 O RF summing amplified output. DPDA 6 I AC coupled RF inputs for the DPD #A, from the main beam photo detector. DPDB 7 I AC coupled RF inputs for the DPD #B, from the main beam photo detector.
DV-SL700W Symbol E_MX8 Pin NO I/O 45 I/O Description GPIO[70] Priority selection E_MX9 46 I/O Function Dir sft_cfg2[5:4]=2'b01 UA1_RXD I sft_cfg7[5:4]=2'b11 656_DATA[0] O sft_cfg1[11:9]=3'b110 RISC_INT1_11 I sft_cfg7[11]=1'b0, sft_cfg0[11]=1'b1, fm_qpio_len[3:0]>8 FM_GPICB[12] I/O sft_cfg0[11]=1'b0, fm_qpio_len[3:0]4'b1100 FM_GPICB[29] I/O sft_cfg8[5]=1'b1 TV_EXT_DATA_Cr[7] (other) GPIO[70](default) I/O I Function Dir GPIO[71] Priority selection sft_cfg2[5:4]=2'b01 UA1_TXD
DV-SL700W Symbol TRAY_OUT/GPIO Pin NO I/O 50 I/O Description Servo TRAY_OUT Priority selection DMEA_OUT/GPIO 51 I/O AT_IORDY sft_cfg4[3]=1'b1 TRAY_OUT (default) 52 I/O 53 IO DAC_PDC I OTP_TEST_ADDR[3] I (other) GPIO[3] 54 IO I/O Servo DMEA Function Dir sft_cfg2[11:10]=2'b01,2'b10 AT_DMACK O sft_cfg4[4]=1'b1 DMEA_OUT (default) O sft_cfg8[9]=1'b1 DAC_PDB I sft_cfg8[8]=1'b1 OTP_TEST_ADDR[4] I (other) GPIO[4] I/O Servo FGIN Function Dir sft_cfg2[11:10]=2'b01,2'b10 AT
DV-SL700W Symbol DFCT/GPIO Pin NO I/O 55 IO Description Servo DFCT Priority selection Function AT_INTRQ I sft_cfg4[6]=1'b1 DFCT (default) O sft_cfg8[8]=1'b1 DAC_DATA_F[7] (other) GPIO[8] VDD_K1 56 S Kernel logic power supply #1 GPIO/TRAY_IS_IN 57 IO GPIO Priority selection GPIO/TRAY_IS_OUT 58 IO Function 59 IO I I/O Dir sft_cfg2[11:10]=2'b01,2'b10 AT_ADR[1] O sft_cfg8[3]=1'b1 DSP_FL2 O fm_qpio_len[3:0]>0 FM_GPIOB[0] I/O sft_cfg8[9]=1'b1 DAC_DATA_F[6] I (other) GPI
DV-SL700W Symbol GPIO/ttio2_6 Pin NO I/O 62 IO Description GPIO Priority selection Function Dir sft_cfg2[11:10]=2'b01,2'b10 AT_CS0 O sft_cfg4[9]=1'b1 ttio6/ttio2 I/O sft_cfg4[15:13]=3'b001 VSYNC_PC O sft_cfg3[15:14]=2'b01 ISA_IOCHRDY I sft_cfg1[11:9]=3'b001 RISC_INT1_13 I sft_cfg3[11:10]=2'b01 ADC_DATA, digital audio I input interface data GPIO/ttio3_7 63 IO fm_qpio_len[3:0]>1 FM_GPIOB[4] sft_cfg8[9]=1'b1 DAC_DATA_F[2] (other) GPIO[13] (default) Priority selection Functi
DV-SL700W Symbol R_CS2_B/GPIO Pin NO I/O 68 IO Description ROM / SRAM / flash chip select #2 or GPIO Priority selection R_CS1_B/GPIO 69 IO Function sft_cfg1[1]=1'b1 R_CS2_B (default) sft_cfg8[9]=1'b1 DAC_DATA_E[7] (other) GPIO[18] Function sft_cfg1[0]=1'b1 R_CS1_B (default) sft_cfg8[9]=1'b1 DAC_DATA_E[6] (other) GPIO[19] RST_B 70 I System reset (active low reset) IR_IN/GPIO 71 I GPIO Priority selection Function sft_cfg8[9]=1'b1 DAC_GPIO[20] (other) GPIO[20] VFD_CLK/GPIO
DV-SL700W Symbol M_CS0_B/GPIO Pin NO I/O 100 IO Description SDRAM chip select 0, or GPIO[24] Priority selection Function Dir O sft_cfg8[9]=1'b1 SDRAM chip select(default) DAC_DATA_D[2] (other) GPIO[24] I/O sft_cfg0[0]=1'b1 M_BAO 101 IO M_DD[15] 102 IO SDRAM data bus [15] M_DD[14] 103 IO SDRAM data bus [14] M_DD[13] 104 IO SDRAM data bus [13] VDD_K2 105 S Kernel logic power supply#2 SDRAM bank select address_[0]_ M_DD[12] 106 IO SDRAM data bus [12] M_DD[11] 107 IO SDR
DV-SL700W Symbol Pin NO I/O Description M_A[10] 126 O SDRAM address bus [10] M_A[0] 127 O SDRAM address bus [0] VSS_04/VSS_K4 128 S Kernel logic I/O power started around supply #4 M_A[1] 129 O SDRAM address bus [1] M_A[2] 130 O SDRAM address bus [2] M_A[3] 131 O SDRAM address bus [3] R_WE_B 132 I/O ROM / SRAM / flash write strobe R_A17 133 I/O ROM / SRAM / flash address bus bit [17] R_A14 134 I/O ROM / SRAM / flash address bus bit [14] R_A13 135 I/O ROM / SRAM / fl
DV-SL700W Symbol Pin NO I/O Description R_D5 147 I/O ROM / SRAM / flash data bus bit [5] R_D4 148 I/O ROM / SRAM / flash data bus bit [4] R_D3 149 I/O ROM / SRAM / flash data bus bit [3] VSS_O5/VSS_K5 150 S R_D2 151 I/O ROM / SRAM / flash data bus bit [2] R_D1 152 I/O ROM / SRAM / flash data bus bit [1] R_D0 153 I/O ROM / SRAM / flash data bus bit [0] R_A0 154 O ROM / SRAM / flash address bus bit [0] R_A1 155 O ROM / SRAM / flash address bus bit [1] R_A2 156 O ROM /
DV-SL700W Symbol A_DATA[3]/GPIO Pin NO I/O Description 176 I/O Serial audio data output for channel 7/6 or GPIO Priority selection A_LRCK/GPIO 177 I/O 178 S A_BCK/GPIO 179 I/O O sft_cfg8[8]=1'b1 ADC_MONO_SPGA I sft_cfg8[9]=1'b1 DAG_TEST (other) GPIO[56] 180 I/O Function Dir sft_cfg3[6]=1'b1 A_LRCK (default) I/O sft_cfg8[8]=1'b1 ADC_MONO_MODE1 sft_cfg8[9]=1'b1 DAC_UD I (other) GPIO[57] I/O 181 I/O PCM bit clock 182 I/O V_BIAS 183 A 184 Dir A_BCK (default) sft_
DV-SL700W Pin NO I/O Description V_DAC[0] Symbol 187 A Video DAC output #0. This is a high-impedance current source output. These outputs can drive a 37.5Ω load directly. VDD_TVA0 188 S TV_DAC power supply #0 VSS_TVA0 189 S TV_DAC ground pin #6 VDD_TVA1 190 S TV_DAC power supply #1 VSS_TVA1 191 S TV_DAC ground pin #1 V_DAC[3] 192 A Video DAC output #3. This is a high-impedance current source output. These outputs can drive a 37.5Ω load directly.
DV-SL700W IC104, EEPROM 2K BIT 2-WIRE SERIAL bidirectional transfer of data. Pin#6 is the serial clock (SCL) input pin. Pin #7 is the write protect (WP) pin used to be protect hardware data. Pin#8 is the power supply (Vcc) pin. DESCRIPTION: The Turbo IC 24CO1/24CO2 is a serial 1K/2K EEPROM fabricated with Turbo’s proprietary, high reliability, high performance CMOS technology. It’s 1K/2K of memory is configured as 16/32 pages with each page containing 8 bytes.
DV-SL700W IC106, CMOS DRAM 143MHZ 16MB Pin Configuration: VDD 1 50 VSS DQ0 2 49 DQ15 DQ1 3 48 DQ14 VSSQ 4 47 VSSQ DQ2 5 46 DQ13 DQ3 6 45 DQ12 VDDQ 7 44 VDDQ DQ4 8 43 DQ11 DQ5 9 42 DQ10 VSSQ 10 41 VSSQ DQ6 11 40 DQ9 DQ7 12 39 DQ8 VDDQ 13 38 VDDQ LDQM 14 37 NC /WE 15 36 UDQM /CAS 16 35 CLK /RAS 17 34 CKE /CS 18 33 NC A11 19 32 A9 A10 20 31 A8 A0 21 30 A7 A1 22 29 A6 A2 23 28 A5 A3 24 27 A4 VDD 25 26 VSS 50pin
DV-SL700W IC106, CMOS DRAM 143MHZ 16MB Functional Block Diagram: Row Decoder Ref. Addr[0:11] Address[0:10] Refresh counter Auto/Self Refresh Refresh Interval Timer Row Addr. Latch/Predecoder Self Refresh Counter 512Kx16 Bank 0 Sense AMP & I/O gates Column Decoder Precharge CKE Row Active CS RAS CAS State Machine BA(A11) Address Register Column Active Column Addr Latch & Counter Overflow Burst Length Counter WE UDQM Row Addr.
DV-SL700W IC120, ST 3.
DV-SL700W IC103A, CMOS 3V 4M FLASH MEMORY Pin Configurations: A11 A9 A8 A13 A14 A17 WE VCC A18 A16 A15 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 MX29LV040 OE A10 CE Q7 Q6 Q5 Q4 Q3 GND Q2 Q1 Q0 A0 A1 A2 A3 Sector Structure Sector A18 A17 A16 Address Range SA0 0 0 0 00000h-0FFFFh SA1 0 0 1 10000h-1FFFFh SA2 0 1 0 20000h-2FFFFh SA3 0 1 1 30000h-3FFFFh SA4 1 0 0 40000h-4FFFFh SA5 1 0 1 50000h-5FFFFh SA6 1 1
DV-SL700W IC103A, CMOS 3V 4M FLASH MEMORY Block Diagram: CE OE WE Y-DECODER ADDRESS LATCH AND BUFFER PROGRAM/ERASE HIGH VOLTAGE X-DECODER A0-A18 CONTROL INPUT LOGIC Y-PASS GATE SENSE AMPLIFIER PGM DATA HV PROGRAM DATA LATCH Q0-Q7 STATE REGISTER MX29LV040 FLASH ARRAY I/O BUFFER 62 WRITE STATE MACHINE (WSM) ARRAY SOURCE HV COMMAND DATA DECODER COMMAND DATA LATCH
DV-SL700W PARTS GUIDE DVD PLAYER MODEL DV-SL700W CONTENTS [1] INTEGRATED CIRCUITS [9] CAPACITORS [2] TRANSISTORS [10] RESISTORS [3] DIODES [11] OTHER CIRCUITARY PARTS [4] FILTER [5] VIBRATORS/CRYSTAL [12] P.C.B. ASSEMBLY (Non Replacement Item) [6] TRANSFORMER [13] CABINET PARTS [7] COILS [14] ACCESSORIES/PACKING PARTS [8] ARRAY PARTS Parts marked with " " are important for maintaining the safety of the set.
DV-SL700W NO.
DV-SL700W NO.
DV-SL700W NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION [9] CAPACITORS ! ! C929,C932 C934 C936 C938 C940 C941 CX1 CY3 92LPXL45647040 92LPME03954010 92LPME03953010 92LPME03954022 92LPXL45647040 92LPME03953010 92LPVX2024F042 92LPVY1705F120 AC AC AC AC AC AC AE AF GP CHIP CAP 0.1 uF 50V 10% 0603 TYPE X7R GP COND ELECT 100 uF 16V 20% Size=5x11mm AI 85°C P=2.5mm GP COND ELECT 100 uF 10V 20% 85°C P=2.5mm Size 5x11mm GP COND ELECT 220 uF 16V 20% 85°C GP CHIP CAP 0.
DV-SL700W NO.
DV-SL700W NO.
DV-SL700W [] EXPLODED VIEW MAIN UNIT A 4 S4x4 B 9 C S3x3 S1 13 11 D S1 12 6 2 S1 E 5 10 F 7 S3 S3x6 G 3 8 4 S2x2 H 1 2 3 4 Figure1 : MAIN BOX PARTS 6 5 6
DV-SL700W -MEMO- 7
DV-SL700W -MEMO- 8
DV-SL700W COPYRIGHT © 2005 BY SHARP CORPORATION ALL RIGHTS RESERVED. No Part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying , recording, or otherwise, without prior written permission of the publisher.
