DV-SL80/DV-SL80X SERVICE MANUAL S45S9DV-SL80/ SERVICE MANUAL DVD VIDEO PLAYER OPERATE NTSC/PAL MODELS DVD VIDEO PLAYER 3 ---DV-SL80 4 DV-SL80 DV-SL80X In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. ---DV-SL80X CONTENTS MODELS DV-SL80/DV-SL80X Page SPECIFICATIONS .............................................................................................
SPECIFICATIONS ITEM UNIT NOMINAL LIMIT Vpp 1.0 ±0.1 2-1 Coaxial Digital Out mVpp 500 2-2 Optical Digital Out dBm -18 Vrm 2.0 dB 120 1 Video Output CONDITIONS 75 Ω (DV-SL80X only) 3 Audio (PCM) 3-1. Output Level 1 kHz 0 dB 3-2. S/N 3-3. Freq. Response DVD fs=48 kHz 20 ~ 22 kHz dB ±0.5 CD fs=44.1 kHz 20 ~ 22 kHz dB ±0.5 DVD 1k Hz 0 dB % 0.0025 CD 1k Hz 0 dB % 0.003 3-4. THD +N 4 Power consumption 14 W (Standby: 2.0 W) --- [ DV-SL80 ] 12 W (Standby: 1.
LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.
IMPORTANT SAFEGUARDS AND PRECAUTIONS 1. IMPORTANT SERVICE NOTES Reverse the AC plug on the set and repeat AC voltage measurements for each exposed part. Any reading of 1.4V rms (this corresponds to 0.7mA rms AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the DVD video player to the owner. BEFORE RETURNING THE DVD VIDEO PLAYER Before returning the DVD video player to the user, perform the following safety checks. 1.
STANDARD NOTES FOR SERVICING Circuit Board Indications Using lead-free wire solder a. The output pin of the 3 pin Regulator ICs is indicated as shown. When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.
How to Remove / Install Flat Pack-IC 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: (1) Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) With Soldering Iron: (1) Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) Flat Pack-IC Desoldering Braid Soldering Iron Fig. S-1-3 Fig.
(4) Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) (5) Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
Instructions for Handling Semi-conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2.
OPERATING CONTROLS AND FUNCTIONS 1 FRONT PANEL 2 3 4 5 9 7 6 OPERATE 8 REAR VIEW AUDIO OUT L CR / PR Y DIGITAL AUDIO OUT 4 CB / PB S-VIDEO OUT 11 12 13 14 15 16 OPTICAL COAXIAL 10 R COMPONENT VIDEO OUT VIDEO OUT 1. OPERATE to switch the player to ON or OFF 2. PLAY to start or resume disc playback 3. STOP to stop playback / REV 4. SKIP goes to previous chapter or track during playback; press and hold for 1.5 seconds for a reverse search / FWD 5.
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally. 1 : Identification (location) No. of parts in the figures 2 : Name of the part 3 : Figure Number for reference 4 : Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered.
(S-3B) [1] Top Case (S-1) (S-3A) CN201 CN601 CN301 CN401 [4] DVD Main CBA Unit A Fig. 1 (L-1) (L-3) Solder Short the three short lands by soldering. (Either of two places.) Short lands (L-1) OR Short lands (L-2) [2] Front Assembly FPC Cable Fig. 2 Solder View for A (S-2) Fig. 4 (S-4) [3] Reinforce Plate [5] DVD Mecha (S-4) (S-4) Fig. 3 Fig.
[7] Function CBA (S-5) [6] AV CBA CN2001 DV-DL80X only (S-6) (S-6) (L-5) Fig. 6 HOW TO EJECT MANUALLY (Method 1) 1 Remove the Top Case. 2 Remove the Reinforce Plate. 3 Rotate the roulette in the direction of the arrow as shown below.
HOW TO EJECT MANUALLY (Method 2) 1 Turn the unit over. 2 Insert the shaft less than a diameter of 3 mm (e.g. screwdriver) straightly into the opening as shown. 3 Turn the shaft along with the opening clockwise. 4 Repeat steps 2 and 3 until the tray will open. 5 Pull the tray slowly with a hand. View for B Rear Turn the shaft along with the opening clockwise. Shaft (e.g.
FIRMWARE RENEWAL MODE The appearance shown in (*2) of Fig. c is described as follows: FIRMWARE is built-in program to operate DVD player. To get rid of error when playing new software (disc) in the market, FIRMWARE version is updated. Perform the following to update the FIRMWARE version. 1. Turn the power on and remove the disc on the tray. 2. To put the DVD player into version up mode, press [9], [8], [7], [6], and [DIRECT SKIP] buttons on the remote control unit in that order.
"*******" differ depending on the models. MODEL : ******* Version : *.** Region : * EEPROM CLEAR : OK EEPROM CLEAR : CLEAR EXIT: POWER Fig. h When "OK" appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11.To exit this mode, press [OPERATE] button.
TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. Is the fuse normal? Yes Is normal state restored when once unplugged power cord is plugged again after several seconds? Yes Is the EV +3.3V line voltage normal? Yes Check each rectifying circuit of the secondary circuit and service it if defective. No No No See FLOW CHART No.2 Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective.
FLOW CHART NO.6 P-ON+10V (EV+11V) is not outputted. Is 11V voltage supplied to the emitter of Q1002? No Yes No Is the voltage of base on Q1002 lower than the voltage of emitter on Q1002 when turning the power on? Check D1030, D1048, C1035, C1048, L1009 and the periphery circuit, and service it if defective. Check Q1016 and PWRCON line and service it if defective. Yes Replace Q1002. FLOW CHART NO.7 P-ON+5V is not outputted. (EV+11V is outputted normally.
FLOW CHART NO.11 The fluorescent display tube does not light up. Is 3.3V voltage supplied to Pins(6,24) of IC2001? Yes Is the voltage of approximately -20V supplied to Pin(15) of IC2001? Yes No No Check the -FL (-20V) line and service it if defective. No Check R2002, IC2001 and their periphery, and service it if defective.
FLOW CHART NO.14 The disc tray cannot be opened and closed. (It can be done using the remote control unit.) Is the normal control voltage inputted to Pin(4) of IC2001? Refer to "FLOW CHART NO.12" No Replace the "OPEN/CLOSE" button (SW2108). Yes Refer to "FLOW CHART NO.15" FLOW CHART NO.15 The disc tray cannot be opened and closed. Replace the DVD Main CBA. No improvement can be found. Yes Replace the DVD Mecha.
FLOW CHART NO.19 Both functions of picture and sound do not operate normally. Replace the DVD Main CBA. No improvement can be found. Yes No Original DVD Main CBA is poor. Replace the DVD Mecha. FLOW CHART NO.20 Picture does not appear normally. Set the disc on the disc tray, and playback.
FLOW CHART NO.21 Audio is not outputted normally. Set the disc on the disc tray, and playback. Are the analog audio signals outputted to each pin of CN1601 on AV CBA? No Replace the DVD Main CBA or DVD Mecha. CN1601 14PIN AUDIO-L CN1601 16PIN AUDIO-R Yes Are the analog audio signals inputted to each pin of IC1201. No IC1201 2PIN AUDIO-L IC1201 6PIN AUDIO-R Check each line between each pin of CN1601 and each pin of IC1201 on AV CBA, and service it if detective.
1-9-1 M SLED MOTOR M SPINDLE MOTOR TRAY-IN TS(+) TS(-) FS(+) FS(-) DRIVE CBA TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM SP(+) SP(-) TRAY-IN GND SL(-) SL(+) PCM-SCLK A-MUTE ADAC-MD ADAC-MC ADAC-ML CN301 3 4 5 6 7 8 - 17 18 12 13 5 6 3 2 - + - + - + IC202 (OP AMP) 23 6 4 5 3 1 2 25 24 27 26 14 7 1 VREF RESET 3 IC462 DVD MAIN CBA UNIT +3.3V + SLED MOTOR DRIVE - + - - + + SPINDLE MOTOR DRIVE TRACKING ACTUATOR DRIVE FOCUS ACTUATOR DRIVE 1 +3.
FS PICK-UP UNIT TS DETECTOR FS(+) FS(-) TS(+) TS(-) CD-LD DVD-LD PD-MONI GND(DVD-PD) GND(CD-PD) GND(LD) C D A B E F CD/DVD 2 13 42 ~ ~ CN201 2 3 1 4 CD 4 6 FS(+) FS(-) TS(+) TS(-) IC201 (SW) DVD DATA RAM INST.
1-9-3 TO SYSTEM CONTROL /SERVO BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM PCM-SCLK A-MUTE ADAC-MD ADAC-MC ADAC-ML PCM-BCK PCM-DATA PCM-LRCLK SPDIF 13 14 15 1 2 3 VIDEO-C VIDEO-Y VIDEO-Cb/Pb VIDEO-Cr/Pr SERIAL CONTROL SERIAL PORT DVD MAIN CBA UNIT 16 SYSTEM CLOCK DAC DAC WF1 WF2 ZERO DETECT ENHANCED MULTI-LEVEL DELTA-SIGMA MODULATOR CN1601 VIDEO-C 10 VIDEO-Y 8 VIDEO-Cb/Pb 6 VIDEO-Cr/Pr 4 4X/8X OVERSAMPLING DIGITAL FILTER /FUNCTION CONTROLLER IC601 (AUDIO DAC) TO DIGITAL SIG
AC1001 AC CORD 1-9-4 LATCH Q1008 DV-SL80 F1001 T1.6A L 250V LINE FILTER L1001 HOT CIRCUIT. BE CAREFUL. AV CBA SWITCHING SWITCHING CONTROL HOT Q1001 Q1003 BRIDGE RECTIFIER D1001, D1002 D1004, D1005 3 4 2 1 D1003 RECTIFIER D1016 RECTIFIER D1030 D1008 SCHOTTKY BARRIER D1006 SCHOTTKY BARRIER RECTIFIER IC1006 REG (SHUNT REGULATOR) 18 6 IC1001 ERROR VOLTAGE DET 17 16 15 14 13 12 11 Q1015 Q1005 Q1011 +1.2V REG.
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply.
DVD Main 1/3 Schematic Diagram 1-10-3 1-10-4 E5943SCD1
DVD Main 2/3 Schematic Diagram 1-10-5 1-10-6 E5943SCD2
IC101 VOLTAGE CHART PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY 1 ~ ~ 33 ~ ~ 65 0 2 ~ ~ 34 3.4 3.4 66 3.4 3 0 0 35 0 0 67 3.2 4 ~ ~ 36 ~ ~ 68 STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY 0 97 ----- ----- 129 2.3 2.3 161 3.4 3.4 193 ~ 3.5 98 3.4 3.4 130 2.3 2.3 162 0 0 194 ~ 3.2 99 0.9 0.8 131 2.3 2.3 163 1.8 1.8 195 ~ 0 0 100 0 0 132 2.4 2.3 164 0 0 196 STOP PIN.
DVD Main 3/3 Schematic Diagram * Note: IC103 is not supplied separately. Be sure to replace with the DVD Main CBA unit when servicing IC103.
AV 1/3 Schematic Diagram CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 1-10-11 CAUTION NOTE : FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE.
AV 2/3 Schematic Diagram 1-10-13 1-10-14 E5943SCAV2
AV 3/3 & Function Schematic Diagram FL2001 MATRIX CHART 7G 6G 5G VCR REPEAT TITLE GROUP A B ALL f i i 4G 3G 2G REC SACD CHP TRK PSCAN DVD A PM HD VCD c f a d g 7G 6G 5G 4G 3G 2G 1G a a a a a SACD b b c c c d d d e REPEAT A B ALL b e e e f f f f f g g g 1G a b b c e d g GROUP h i 1-10-15 i TITLE VCR 1-10-16 PSCAN DVD d d A e e P f f M g g HD CHP TRK V REC CD b b c c E5943SCAV3
DVD MAIN CBA Top View 1-10-17 1-10-18 BE5900G04012
DVD MAIN CBA Bottom View 1-10-19 1-10-20 BE5900G04012
AV CBA Top View CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 1-10-21 CAUTION FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE.
AV CBA Bottom View CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
FUNCTION CBA Top View FUNCTION CBA Bottom View 1-10-25 1-10-26 BE5942F01011B
WAVEFORMS WF1 Pin 8 of CN1601 VIDEO-Y WF2 0.2V 20µs 20 0.2V Pin 16 of CN1601 AUDIO-R Pin 10 of CN1601 VIDEO-C WF3 WF5 WF6 20µs 20 1V 0.5ms Pin 19 of CN1601 SPDIF 1V 0.1µs 0.1 C1402 PLUS LEAD NOTE: VIDEO-CVBS WF4 0.5V Input CD: 1kHz PLAY (WF4~WF6) DVD: POWER ON (STOP) MODE (WF1~WF3) 20µs 20 Pin 14 of CN1601 AUDIO-L 1V 0.
VIDEO OUT VIDEO-Y OUT VIDEO-Cb/Pb OUT OPTICAL COAXIAL DIGITAL AUDIO OUT CN1601 (CN1601 is soldered directly to the PCB.
SYSTEM CONTROL TIMING CHARTS Tray Close ~ Play / Play ~ Tray Open Tray Close Disc Rotation Play Disc Stop Tray Open 3.3V Tray IN (TL221) Sled Drive (TP303) 0V 1.65V 0V Disc Drive (TP301) 1.65V Focus Drive (TP304) 1.65V 0V 0V Tracking Drive (TP302) 1.
IC PIN FUNCTION DESCRIPTIONS IC2001 ( PT6313-S -TP ) Pin In/Out No.
LEAD IDENTIFICATIONS KRA110M KTA1267(Y) KTC3199(GR,Y) KTC3203(Y) KTA1266 (Y) 0C-0805T*002 1 2 3 E C B E C B PQ070XZ5MZP 3 12345 PT6313-S-TP KIA4558P 8 5 28 15 1 4 1 14 KIA431-AT 1: Vin 2: Vc 3: Vo 4: Vadj 5: GND K A R MM1637XVBE 16 2SK3566 9 LTV-817B-F A K 1 8 G D S 1-15-1 C E Note: A: Anode K: Cathode E: Emitter C: Collector B: Base R: Reference S: Source G: Gate D: Drain E5943LE
EXPLODED VIEWS Cabinet See Electrical Parts List for parts with this mark. 2L011 Some Ref. Numbers are not in sequence.
Packing X2 X5 X10 X1 S2 X4 S4 Unit S2 A22 S1 1-16-2 E5943EX
MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. COMPARISON OF MODELS Ref. No.
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that not assigned part numbers (---------) are not available. 2. IC103 is not supplied separately. Be sure to replace with the DVD Main CBA unit when servicing IC103. 3.
Ref. No. C191 C192 C195 C196 C201 C202 C203 C207 C208 C210 C211 C212 C215 C217 C218 C219 C220 C221 C222 C223 C224 C225 C226 C227 C228 C229 C230 C231 C232 C233 C234 C237 C238 C239 C250 C253 C255 C257 C259 C263 C280 C281 C284 C288 C289 C301 C302 C303 C305 C308 C310 C311 C313 C314 C315 C316 C317 C318 C324 C325 C326 C327 C328 C329 C402 C403 C405 C410 C411 Mark Description Part No. CHIP CERAMIC CAP.(1005) CH J 15pF/50V CHIP CERAMIC CAP.(1005) CH J 22pF/50V CHIP CERAMIC CAP.(1005) F Z 0.
Ref. No. C412 C416 C417 C418 C421 C422 C423 C424 C425 C426 C471 C472 C501 C502 C503 C504 C505 C506 C507 C508 C509 C510 C511 C512 C514 C561 C601 C602 C605 C606 C608 C609 C610 C611 C619 C620 C621 C622 C624 C658 C901 C902 C904 C905 C910 C913 C914 C915 C916 C917 C918 C919 CONNECTORS CN201 CN301 CN401 CN601 DIODE D204 ICs IC101 IC103 IC201 IC202 IC301 IC461 IC462 IC503 IC601 Mark Description Part No. Code CHIP CERAMIC CAP.(1005) F Z 0.1µF/16V CHIP CERAMIC CAP.(1005) F Z 0.1µF/16V CHIP CERAMIC CAP.
Ref. No. COILS L104 L106 L107 L108 L201 L250 L401 L402 L403 L501 L561 L611 L612 L613 L614 L618 TRANSISTORS Q251 Q252 Q253 Q254 RESISTORS R101 R102 R106 R107 R108 R109 R110 R112 R113 R114 R116 R120 R121 R122 R124 R128 R131 R133 R191 R192 R203 R206 R208 R213 R214 R217 R218 R219 R220 R225 R226 R227 R228 R231 R232 R233 R234 R241 R242 R243 R251 R252 R255 R258 R261 R262 Mark Description Part No. Code CHIP BEAD MMZ1608Y121CT CHIP RES.(1608) 1/10W 0 Ω CHIP RES.
Ref. No. R265 R268 R270 R271 R274 R275 R276 R277 R278 R279 R280 R281 R282 R283 R284 R285 R286 R289 R298 R299 R301 R302 R303 R304 R305 R306 R307 R308 R313 R315 R316 R317 R318 R319 R320 R321 R322 R325 R333 R334 R402 R403 R404 R405 R406 R407 R413 R415 R417 R421 R422 R423 R471 R509 R510 R562 R565 R567 R601 R607 R618 R619 MISCELLANEOUS X101 Mark Description CHIP RES.(1005) 1/16W J 470 Ω CHIP RES.(1005) 1/16W J 180 Ω CHIP RES.(1005) 1/16W J 8.2k Ω CHIP RES.(1005) 1/16W J 18k Ω CHIP RES.(1005) 1/16W J 4.
AV CBA + FUNCTION CBA Ref. No. Mark A A A B B B Description Part No. AV CBA + FUNCTION CBA Consists of the following AV CBA FUNCTION CBA AV CBA + FUNCTION CBA Consists of the following AV CBA FUNCTION CBA Code 9HS1VSA10081 BR 9HS1VSA10081A 9HS1VSA10081B 9HS1VSA10069 BR AS BR 9HS1VSA10069A 9HS1VSA10069B BR AS AV CBA Ref. No.
Ref. No. C1361 C1362 C1394 C1395 C1402 C1421 C1422 C1441 C1442 C1461 C1462 C1481 C1482 C1522 C1524 C1531 C1532 C1533 C1534 C2001 C2002 C2003 C2004 C2031 C2032 C2034 CONNECTORS CN1001 CN1601 CN2001 DIODES D1001 D1002 D1003 D1004 D1005 D1006 D1008 D1011 D1012 D1016 D1017 D1018 D1022 D1024 D1025 D1030 D1046 D1047 D1048 D1051 D1055 D1058 D1059 D1070 D1073 D1073 D1301 D2041 D2042 D2043 D2044 ICs IC1001! IC1002 IC1006 IC1201 IC1204 IC1402 Mark B A A B B Description ELECTROLYTIC CAP. 220µF/6.
Ref. No.
Ref. No. R1068 R1069 R1072 R1073 R1074 R1075 R1076 R1077 R1078 R1079 R1080 R1081 R1082 R1083 R1084 R1085 R1091 R1092 R1095 R1096 R1097 R1205 R1206 R1207 R1208 R1209 R1210 R1211 R1212 R1221 R1222 R1223 R1224 R1225 R1226 R1227 R1228 R1236 R1238 R1240 R1245 R1351 R1352 R1353 R1354 R1355 R1356 R1366 R1392 R1396 R1397 R1402 R1421 R1422 R1441 R1442 R1443 R1461 R1462 R1481 R1482 R1521 R2001 R2002 R2012 R2013 R2014 R2015 R2016 Mark B A Description Part No. CARBON RES. 1/6W J 820 Ω CARBON RES.
Ref. No. R2031 R2032 R2033 R2041 R2042 R2043 R2044 R2045 MISCELLANEOUS 2L042 2B1 2B11 AC1001! AC1001! F1001! FL2001 FH1001 FH1002 J2647 JK1202 JK1401 JK1404 RM2001 SA1001! T1001! T1001! Mark A A A B A B Description CHIP RES.(1608) 1/10W J 6.8k Ω CHIP RES.(1608) 1/10W J 10k Ω CHIP RES.(1608) 1/10W J 22k Ω CHIP RES.(1608) 1/10W J 10k Ω CHIP RES.(1608) 1/10W J 10k Ω CHIP RES.(1608) 1/10W J 10k Ω CHIP RES.(1608) 1/10W J 10k Ω CHIP RES.(1608) 1/10W 0 Ω Part No.
DV-SL80/DV-SL80X COPYRIGHT © 2004 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan Jun.
