Manual
Table Of Contents
- WARNING
- CAUTION
- --- English version ---
- INTRODUCTION
- IMPORTANT
- PRECAUTION
- CONTENTS
- PARTS AND THEIR FUNCTIONS
- GETTING STARTED
- OVERVIEW OF FLOW OF DAILY SALES ENTRIES
- BASIC SALES ENTRY
- OPTIONAL FEATURES
- CORRECTION
- PRIOR TO PROGRAMMING
- BASIC FUNCTION PROGRAMMING (For Quick Start)
- AUXILIARY FUNCTION PROGRAMMING
- ADVANCED PROGRAMMING
- TRAINING MODE
- READING (X) AND RESETTING (Z) OF SALES TOTALS
- OVERRIDE ENTRIES
- CORRECTION AFTER FINALIZING A TRANSACTION (Void mode)
- OPERATOR MAINTENANCE
- 1 In case of Power Failure
- 2 In Case of Printer Error
- 3 Cautions in Handling the Printer and Recording Paper
- 4 Replacing the Paper Roll
- 5 Removing a Paper Jam
- 6 Cleaning the Print Head
- 7 Removing the Till and the Drawer
- 8 Opening the Drawer by Hand
- 9 Mounting the Spill-proof Cover
- 10 Before Calling for Service
- SPECIFICATIONS
- --- La versión española ---
- INTRODUCCION
- IMPORTANTE
- PRECAUCION
- INDICE
- PARTES Y SUS FUNCIONES
- PARA EMPEZAR
- REGISTRO BASICO DE VENTAS
- CARACTERISTICAS OPCIONALES
- CORRECCION
- PROGRAMACION DE LAS FUNCIONES BASICAS (Para el inicio rápido)
- PROGRAMACION DE FUNCIONES AUXILIARES
- 1 Programación de secciones
- 2 Programación de PLU (codificación de precios) y subsección
- 3 Programación de la tasa de comisión
- 4 Programación de teclas misceláneas
- Tasa para [%1], [%2] y [CONV]
- Importe para [(-)]
- Límite de tasa porcentual para [%1] y [%2]
- Parámetros de función para [%1], [%2] y [(-)]
- Parámetros de función para [CONV]
- Límite de dígitos de entrada para [RA], [RCPT/PO] y [TAX]
- Parámetros de función para [CHK], [CH1], [CH2] y [CA/AT/NS] (cuando se usa como tecla CA)
- 5 Programación de texto
- PROGRAMACION AVANZADA
- 1 Programación de número de caja registradora y de número consecutivo
- 2 Programación 1 de selección de diversas funciones
- 3 Programación 2 de selección de diversas funciones
- Modo de ahorro de energía
- Formato de impresión del mensaje del membrete
- Bloqueo de importe alto (HALO) para metálico en el cajón (CID) (centinela)
- Interfaz RS-232C
- Densidad de la impresora térmica
- Selección del idioma
- Especificación de dependientes de instrucción para el modo de instrucción
- Programación de la tecla AUTO — Tecla de secuencia automática
- 4 Lectura de programas almacenados
- MODO DE INSTRUCCION
- LECTURA (X) Y REPOSICION (Z) DE LOS TOTALES DE VENTAS
- REGISTROS DE ANULACION
- CORRECCION DESPUES DE FINALIZAR UNA TRANSACCION (Modo de cancelación)
- MANTENIMIENTO PARA EL OPERADOR
- 1 En caso de corte de la alimentación
- 2 En el caso de error de impresora
- 3 Precauciones al manejar la impresora
- 4 Reemplazo del rollo de papel
- 5 Extracción del papel atascado
- 6 Limpieza del cabezal de impresión
- 7 Extracción del separador de dinero y del cajón
- 8 Abertura manual del cajón
- 9 Colocación de la cubierta impermeable
- 10 Antes de solicitar el servicio de un técnico
13
Clerk assignment
Prior to any item entries, clerks must enter their clerk codes into the register. However, the code entry may not
be necessary when the same clerk handles consecutive transactions.
Receipt ON/OFF function
You can disable receipt printing in the REG mode to save paper using the receipt ON/OFF function. To disable
receipt printing, press the
R
key in the OP X/Z position. This key toggles the receipt printing status ON and
OFF.
To check the receipt printing status, turn the mode switch to the OP X/Z position or press the
l
key in the REG
mode. When the function is in the OFF mode, the receipt off indicator “_” illuminates.
The register will print reports regardless of the receipt state, so the paper roll must be installed.
To issue a receipt when receipt ON/OFF function is set to OFF:
If your customer wants a receipt after you finalized a transaction with the receipt ON/OFF function in the OFF
mode, press the
R
key. This will produce a receipt. If more than 30 items were entered, the receipt will be
issued in a summary receipt format.
Power Save Mode
The register will enter into power save mode when no entries are performed based on the pre-programmed time
limit (by default, 30 minutes).
When the register goes to the power save mode, all display lights will turn off except the decimal point at the
leftmost position of the lower line. The register will return to normal operation mode when any key is pressed or
a mode is changed with the mode key. Please note when the register is recovered by a key entry, its key entry
is invalid. After the recovery, start the key entry from the beginning.
L
Clerk code 1 to 20
To display the signed-on clerk code
LL
■ Sign-on (in REG, MGR, VOID mode) ■ Sign-off (in REG, MGR, VOID mode)
In the following examples, your register will go into an error state accompanied with a warning beep and a
corresponding error message. Clear the error state by pressing the
l
key and take proper action.
Please refer to the error message table on page 69.
• Enter over a 32-digit number (entry limit overflow): Cancel the entry and re-enter the correct number.
• An error in key operation: Clear the error and continue operation.
• An entry beyond a programmed amount entry limit: Check to see if the entered amount is correct. If it is
correct, it can be rung up in the MGR mode. Contact your manager.
• An including-tax subtotal exceeds eight digits: Delete the subtotal by pressing the
l
key and press the
A
,
C
,
X
or
Y
key to finalize the transaction.
Error escape function
To quit a transaction due to an error or an unforeseen event, use the error escape function as shown below:
The transaction is voided (treated as a subtotal void) and the receipt is issued by this function. If you have
already entered a tendered amount, the operation is finalized as a cash sale.
l
Transaction
To clear the error state
E
E
Error Warning
2