Manual
Table Of Contents
- WARNING
- CAUTION
- --- English version ---
- INTRODUCTION
- IMPORTANT
- PRECAUTION
- CONTENTS
- PARTS AND THEIR FUNCTIONS
- GETTING STARTED
- OVERVIEW OF FLOW OF DAILY SALES ENTRIES
- BASIC SALES ENTRY
- OPTIONAL FEATURES
- CORRECTION
- PRIOR TO PROGRAMMING
- BASIC FUNCTION PROGRAMMING (For Quick Start)
- AUXILIARY FUNCTION PROGRAMMING
- ADVANCED PROGRAMMING
- TRAINING MODE
- READING (X) AND RESETTING (Z) OF SALES TOTALS
- OVERRIDE ENTRIES
- CORRECTION AFTER FINALIZING A TRANSACTION (Void mode)
- OPERATOR MAINTENANCE
- 1 In case of Power Failure
- 2 In Case of Printer Error
- 3 Cautions in Handling the Printer and Recording Paper
- 4 Replacing the Paper Roll
- 5 Removing a Paper Jam
- 6 Cleaning the Print Head
- 7 Removing the Till and the Drawer
- 8 Opening the Drawer by Hand
- 9 Mounting the Spill-proof Cover
- 10 Before Calling for Service
- SPECIFICATIONS
- --- La versión española ---
- INTRODUCCION
- IMPORTANTE
- PRECAUCION
- INDICE
- PARTES Y SUS FUNCIONES
- PARA EMPEZAR
- REGISTRO BASICO DE VENTAS
- CARACTERISTICAS OPCIONALES
- CORRECCION
- PROGRAMACION DE LAS FUNCIONES BASICAS (Para el inicio rápido)
- PROGRAMACION DE FUNCIONES AUXILIARES
- 1 Programación de secciones
- 2 Programación de PLU (codificación de precios) y subsección
- 3 Programación de la tasa de comisión
- 4 Programación de teclas misceláneas
- Tasa para [%1], [%2] y [CONV]
- Importe para [(-)]
- Límite de tasa porcentual para [%1] y [%2]
- Parámetros de función para [%1], [%2] y [(-)]
- Parámetros de función para [CONV]
- Límite de dígitos de entrada para [RA], [RCPT/PO] y [TAX]
- Parámetros de función para [CHK], [CH1], [CH2] y [CA/AT/NS] (cuando se usa como tecla CA)
- 5 Programación de texto
- PROGRAMACION AVANZADA
- 1 Programación de número de caja registradora y de número consecutivo
- 2 Programación 1 de selección de diversas funciones
- 3 Programación 2 de selección de diversas funciones
- Modo de ahorro de energía
- Formato de impresión del mensaje del membrete
- Bloqueo de importe alto (HALO) para metálico en el cajón (CID) (centinela)
- Interfaz RS-232C
- Densidad de la impresora térmica
- Selección del idioma
- Especificación de dependientes de instrucción para el modo de instrucción
- Programación de la tecla AUTO — Tecla de secuencia automática
- 4 Lectura de programas almacenados
- MODO DE INSTRUCCION
- LECTURA (X) Y REPOSICION (Z) DE LOS TOTALES DE VENTAS
- REGISTROS DE ANULACION
- CORRECCION DESPUES DE FINALIZAR UNA TRANSACCION (Modo de cancelación)
- MANTENIMIENTO PARA EL OPERADOR
- 1 En caso de corte de la alimentación
- 2 En el caso de error de impresora
- 3 Precauciones al manejar la impresora
- 4 Reemplazo del rollo de papel
- 5 Extracción del papel atascado
- 6 Limpieza del cabezal de impresión
- 7 Extracción del separador de dinero y del cajón
- 8 Abertura manual del cajón
- 9 Colocación de la cubierta impermeable
- 10 Antes de solicitar el servicio de un técnico
57
READING (X) AND RESETTING (Z)
OF SALES TOTALS
• Use the reading function (X) when you need to take a reading of sales information entered since the last reset.
You can take this reading any number of times. It does not affect the register’s memory.
• Use the resetting function (Z) when you need to clear the register’s memory. Resetting prints all sales
information and clears the entire memory except for the GT1 through GT3, Training GT, reset count, and
consecutive number.
X1 and Z1 reports: Daily sales reports
X2 and Z2 reports: Periodic (monthly) consolidation reports
When you take an X or Z report, turn the mode switch to the appropriate position referring to the column of
“Mode switch position” shown on the table below, and use the following corresponding key sequence.
Item
Mode switch position
Key operation
D
OPX/Z
X
--
--
--
--
--
--
--
A
key: Sales total
@
key: Amount of cash in drawer
For dept. 21 to 40; Dept. key (
¡
to
π
)
Dept. code : Department total amount
d
For dept. 1 to 20; Dept. key (
¡
to
π
)
Individual group
total report on
department
PLU report by
designated range
X1/Z1
--
X1, Z1
X1, Z1
X2/Z2
--
X2, Z2
X2, Z2
Flash report:
(Only display)
To clear the
display, press the
l
key or turn the
mode switch to
another position.
Full sales report
Department report
X1 X2
Transaction report
X1 X2
X1 X2
Full group total
report on
department
X1 X2
PLU report by
associated
department
X1 X2
P
AA
Reading: Resetting:
d
Reading:
0
Reading:
@
1A
Reading:
d
Reading: Associated dept. code
D
p
@
d
Reading: Group number
Resetting:
P
All PLUs
End
PLU code
Start
PLU code
p@
Reading:
All PLUs
End
PLU code
Start
PLU code
p@
Summary of Reading (X) and Resetting (Z) Reports
1