Owner's Manual

ManualsBrandsSharp ManualsPrintersSharp FO-2080_for_FAX_Function

MODEL

FO-2080

• INSTALLATION

• INITIAL SETTINGS

• CHOOSING SUITABLE

MEDIA

• HOW TO USE THE FAX

FUNCTION

• SPECIAL FUNCTIONS

• TROUBLESHOOTING

• APPENDIX

Page

OPERATION MANUAL

(for facsimile)

FO 2080 OPERATION MANUAL (for facsimile)

!AR-FX13_sec.book 1 ページ２００９年５月１１日　月曜日　午後２時２４分

Summary of content (104 pages)

PAGE 1
!AR-FX13_sec.
PAGE 2
２００９年５月１１日　月曜日　午後２時２４分 For users in the USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
!AR-FX13_sec.book i ページ２００９年５月１１日　月曜日　午後２時２４分 INTRODUCTION TYPE OF SERVICE This equipment may not be used on coin-operated (pay phone) phone service. Connection to party lines service is subject to state tariffs. Contact your state's public utility commission, public service commission, or corporation commission for more information.
PAGE 4
!AR-FX13_sec.book ii ページ２００９年５月１１日　月曜日　午後２時２４分 FCC Notice to users: This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. The REN is used to determine the number of devices that may be connected to a telephone line.
PAGE 5
!AR-FX13_sec.book 1 ページ２００９年５月１１日　月曜日　午後２時２４分 TABLE OF CONTENTS INTRODUCTION ......................................................................................................................................... i QUICK REFERENCE GUIDE .................................................................................................................... 3 LIST OF FAX FUNCTIONS........................................................................................................................
PAGE 6
!AR-FX13_sec.book 4 2 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION 5 SPECIAL FUNCTIONS SENDING ORIGINALS ................................... 52 MEMORY .........................................................67 ● SETTING THE ORIGINAL .............................52 DATA TRANSFER...........................................68 OPTIONAL TRANSMISSION SETTINGS ...... 54 TRANSMISSION RESERVATION...................70 ● ● ● ● ● ● ORIGINAL SIZE.............................................
PAGE 7
!AR-FX13_sec.book 3 ページ２００９年５月１１日　月曜日　午後２時２４分 QUICK REFERENCE GUIDE The following quick reference guide provides brief explanations the operation of the machine. Selecting the transmission mode (p.26) Memory transmission mode The indicator lights up when memory transmission mode is selected. Direct transmission mode Press the [MEMORY] key to change modes. The indicator is off when direct transmission mode is selected. Place the original Using the RSPF (p.
PAGE 8
!AR-FX13_sec.book 4 ページ２００９年５月１１日　月曜日　午後２時２４分 Sending a fax Dialing methods Direct Dialing (p.59) Press the numeric keys to dial. SPEED/ SEARCH Speed Dialing (p.59) Rapid Key Dialing (p.59) 01 10 Chain Dialing (p.60) SPEED/ SEARCH Enter a two-digit Speed Dial number. 09 18 01 10 * It is not necessary to press the [START] key after pressing a Rapid Key. 09 18 Speed Dial number or Rapid Key set for Chain Dialing when stored.
PAGE 9
!AR-FX13_sec.book 5 ページ２００９年５月１１日　月曜日　午後２時２４分 Sending a fax to multiple destinations (Broadcasting) (p.71) RESOLUTION BROADCAST Dial. CONTRAST Adjust the resolution and contrast. (p.55) Place the original. Storing a fax job while another job is in progress Fax transmission or reception in progress RESOLUTION Place the original. CONTRAST Dial. Adjust the resolution and contrast. (p.55) The fax will be transmitted after previous jobs are completed.
PAGE 10
!AR-FX13_sec.book 6 ページ２００９年５月１１日　月曜日　午後２時２４分 LIST OF FAX FUNCTIONS The FAX MAIN MENU is used to configure settings for the fax function and program information such as the fax number of the machine. The settings in the FAX MAIN MENU are shown below. The procedure for configuring settings is explained in "SELECTING SETTINGS FOR THE FUNCTION" (p.10).
PAGE 11
!AR-FX13_sec.book 7 ページ２００９年５月１１日　月曜日　午後２時２４分 Menu item 6 : AUTO LISTING Settings (factory default setting appears in bold) Page Enable automatic printing of the Activity Report when information on a total of 50 fax transmissions/receptions accumulates. 1 : ON 2 : OFF 88 1 : TRANSMISSION Select the condition for printing reports on fax transmissions. 1 : ALWAYS PRINTS 2 : ERROR ONLY 3 : NEVER PRINTS 89 2 : BROADCAST Select the condition for printing reports on broadcast transmissions.
PAGE 12
!AR-FX13_sec.book 8 ページ２００９年５月１１日　月曜日　午後２時２４分 Menu item 16 : RCV REDUCE 17 : BEEP LENGTH 18 : RINGER VOLUME 19 : BEEPER VOLUME 20 : DIAL MODE 21 : DISTINCTIVE RING 22 : INDEX PRINT 23 : DATE&TIME FORMAT 24 : 2-SIDED RX 25 : TRAY SELECTION 8 Settings (factory default setting appears in bold) Page When a fax is received that is larger that the printing paper, enable reduction of the fax to the size of the paper to avoid the fax being cut off.
PAGE 13
!AR-FX13_sec.book 9 ページ２００９年５月１１日　月曜日　午後２時２４分 Menu item Settings (factory default setting appears in bold) Page 5 :ANTI JUNK FAX 1 : ANTI JUNK SELECT Enable the anti junk function to block fax reception from specified fax numbers. 1 : ON 2 : OFF 81 Program (or delete) fax numbers from which fax reception is to be blocked. 1 : SET 2 : CLEAR 82 Activate fax reception when a period of silence longer than the set time is detected.
PAGE 14
!AR-FX13_sec.book 10 ページ２００９年５月１１日　月曜日　午後２時２４分 SELECTING SETTINGS FOR THE FUNCTION The general procedure for configuring settings for the fax function is explained below. Follow this procedure to configure the settings explained on pages 6 through 9. Note 1 An item can also be selected after pressing the [MENU] key by pressing the numeric key for the item (the key corresponding to the number that appears in front of the item). When the numeric key is pressed, the item is selected or entered.
PAGE 15
!AR-FX13_sec.book 11 ページ２００９年５月１１日　月曜日　午後２時２４分 Chapter 1 1 INSTALLATION CONNECTIONS CONNECTING THE TELEPHONE LINE CORD Plug one end of the telephone line cord into the jack on the machine marked "LINE." Plug the other side into a standard (RJ11C) single-line telephone wall jack. Be sure not to plug this telephone line cord into the "TEL" jack. The "TEL" jack is used to attach an extension telephone or answering machine to the machine. (See "CONNECTING OTHER DEVICES" (p.
PAGE 16
!AR-FX13_sec.book 12 ページ２００９年５月１１日　月曜日　午後２時２４分 FINAL PREPARATIONS CONNECTING OTHER DEVICES If desired, an answering machine or external telephone can be connected to the machine through the telephone jack, labeled "TEL," on the rear of the machine. ● Connecting an answering machine to the machine allows you to receive both voice and fax messages when you are out. To use this feature, first change the outgoing message of your answering machine, and then set the reception mode of the machine to "A.M.
PAGE 17
!AR-FX13_sec.
PAGE 18
!AR-FX13_sec.book 14 ページ２００９年５月１１日　月曜日　午後２時２４分 A LOOK AT THE FAX OPERATION PANEL 1 2 3 4 5 6 7 13 8 14 9 10 15 16 17 18 19 20 1 Rapid keys Press one of these keys to dial a fax or telephone number automatically. 8 [RESOLUTION] key Press this key to adjust the resolution before sending faxes. 2 [MEMORY] key / indicator Used for sending faxes in memory (indicator is lit) or direct sending (indicator is not lit).
PAGE 19
!AR-FX13_sec.book 15 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS 11 12 2 21 22 23 24 25 15 [SPEAKER] key Press this key to begin manual dialing. (To close the line, press the [SPEAKER] key again.) 16 17 26 27 28 23 LINE STATUS indicator Lit when sending/receiving faxes, blinking when receiving data. [ ] key Press this key to enter symbols during a name storing procedure. Press the " " key to change from pulse dialing to tone dialing mode.
PAGE 20
!AR-FX13_sec.book 16 ページ２００９年５月１１日　月曜日　午後２時２４分 ABOUT THE LIQUID CRYSTAL DISPLAY The machine is equipped with a two-line liquid crystal display (LCD) on the operation panel for displaying various messages and settings during operation. This LCD can display up to 20 characters on each line. When the machine is idle, the LCD shows the date, time, reception mode and the stand-by memory available. Example: When an original is placed in the RSPF, the second line changes from "STAND-BY" to "SEND READY".
PAGE 21
!AR-FX13_sec.book 17 ページ２００９年５月１１日　月曜日　午後２時２４分 ADJUSTING THE RINGING VOLUME Adjust the ringing volume of the machine following the procedure below. 1 Press the [MENU] key. 5 Press the [ENTER] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key. 6 Press the [MENU] key. Press the [MENU] key to exit. Selection "4:USER PROGRAM" 3 Press the [ ] key ( ) or [ ] key ( ) until "18:RINGER VOLUME" appears, and then press the [ENTER] key.
PAGE 22
!AR-FX13_sec.book 18 ページ２００９年５月１１日　月曜日　午後２時２４分 SETTING THE LENGTH OF ALARM BEEPS You can select the length in seconds of the alarm beeps (emitted at the end of transmission and reception) following the procedure below. 1 6 Press the [MENU] key. Press the [MENU] key. Press the [MENU] key to exit. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key.
PAGE 23
!AR-FX13_sec.book 19 ページ２００９年５月１１日　月曜日　午後２時２４分 ADJUSTING THE ALARM BEEP VOLUME Adjust the volume of alarm beeps (emitted at the end of transmission and reception) following the procedure below. 1 6 Press the [MENU] key. Press the [MENU] key. Press the [MENU] key to exit. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key.
PAGE 24
!AR-FX13_sec.book 20 ページ２００９年５月１１日　月曜日　午後２時２４分 FAX SETUP HOW TO ENTER CHARACTERS You can enter letters with the numeric keys. Letters are marked above each of the numeric keys [2] through [9]. To enter a letter, press the appropriate key repeatedly until the desired letter appears (the number of the key appears first, followed by letters in the order marked above the key). The keys used for entering characters are shown below.
PAGE 25
!AR-FX13_sec.book 21 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS ENTERING YOUR NAME AND FAX NUMBER Note You can view all of the items in the menu display by pressing the [MENU] key, then using the [ ] key ( ) or [ ] key ( ) to scroll through the function list. Pressing the [ENTER] key chooses the displayed function. Procedures for inputting various items (name, telephone number, date, etc.) are given as follows.
PAGE 26
!AR-FX13_sec.book 22 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS 8 Press the [ENTER] key. 9 Press the [MENU] key. Press the [MENU] key to exit. SETTING THE DATE AND TIME The date and time that appear in the display are printed at the top of each page you transmit. Set the date and time by pressing the keys on the operation panel as shown below. If you enter an incorrect number, press the [CLEAR] key ( ) and re-enter the number. The time can be displayed in 12-hour or 24-hour format.
PAGE 27
!AR-FX13_sec.book 23 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS To change the display format to 12-hour or 24-hour format, follow the steps below: 1 Press the [MENU] key. 6 Press the [ENTER] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key. 7 Press the [MENU] key. Press the [MENU] key to exit. Selection "4:USER PROGRAM" 3 Press the [ ] key ( ) or [ ] key ( ) until "23:DATE&TIME FORMAT" appears, and then press the [ENTER] key.
PAGE 28
!AR-FX13_sec.book 24 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS To change the order of display of the date, follow the steps below: 1 Press the [MENU] key. 6 Press the [ENTER] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key. 7 Press the [MENU] key. Selection "4:USER PROGRAM" 3 Press the [ ] key ( ) or [ ] key ( ) until "23:DATE&TIME FORMAT" appears, and then press the [ENTER] key.
PAGE 29
!AR-FX13_sec.book 25 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS Daylight Saving Time Setting Enable this setting to have the internal clock automatically move forward and backward at the beginning and end of Daylight Saving Time. Note If a transmission is in progress when the clock adjustment time for daylight savings time arrives, the clock will not be adjusted until the transmission ends. Follow these steps to enable Daylight Saving Time. 1 5 Press the [MENU] key. Press the [ENTER] key.
PAGE 30
!AR-FX13_sec.book 26 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SELECTING THE TRANSMISSION MODE The machine has two modes for sending faxes: memory transmission and direct transmission. To change modes, press the [MEMORY] key. The MEMORY indicator lights up when memory transmission is selected, and goes off when direct transmission is selected.
PAGE 31
!AR-FX13_sec.book 27 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SELECTING THE RECEPTION MODE Your machine has three modes for receiving incoming calls and faxes: ● AUTO mode: Select this mode when you only want to receive faxes on your telephone line. The machine will automatically answer all calls and receive incoming faxes. ● MAN. mode: This is the most convenient mode for receiving phone calls if you have an extension phone.
PAGE 32
!AR-FX13_sec.book 28 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING THE NUMBER OF RINGS FOR AUTO RECEPTION You can set the number of rings before the machine answers in AUTO mode following the procedure below. 1 Press the [MENU] key. 6 Press the [MENU] key. Press the [MENU] key to exit. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key.
PAGE 33
!AR-FX13_sec.book 29 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING THE NUMBER OF RINGS FOR MANUAL RECEPTION The number of rings before the machine answers in MANUAL mode can also be set. If you do not want the machine to answer at all in MANUAL Mode, select "0" in Step 4 below. 1 Press the [MENU] key. 4 Press a numeric key to select the number of rings. Select the number of rings you would like to use (0 to 9).
PAGE 34
!AR-FX13_sec.book 30 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING THE TRAY SELECTION (when the 250-sheet paper feed unit is installed) Follow the steps below to select the paper tray for received faxes. 1 Press the [MENU] key. 5 Press the [ENTER] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key. 6 Press the [MENU] key. Press the [MENU] key to exit.
PAGE 35
!AR-FX13_sec.book 31 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING THE DIAL MODE The machine can be used with both touch-tone and pulse telephone lines. Touch-tone uses tones of different pitches for each numeric key, while pulse lines use a series of pulses. Your machine must be set to match the kind of telephone line you are using: touch-tone or pulse. 1 6 Press the [MENU] key. Press the [MENU] key. Press the [MENU] key to exit.
PAGE 36
!AR-FX13_sec.book 32 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING THE NUMBER OF RECALL TIMES The machine will automatically reattempt transmission when a transmission is not successful because the line is busy or a communication error occurs. This setting is used to select the number of recall attempts that will be made. Note • If a transmission is still not successful after the set number of recall attempts is made, a report will print and the document will be cleared from memory.
PAGE 37
!AR-FX13_sec.book 33 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS When a communication error occurs You can select the number of recall attempts made when a communication error occurs. If "0" is entered, the machine will not make any recall attempts. 1 Press the [MENU] key. 6 Press the [MENU] key. Press the [MENU] key to exit. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key.
PAGE 38
!AR-FX13_sec.book 34 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING THE RECALL INTERVAL The machine will automatically reattempt transmission when a transmission is not successful because the line is busy or a communication error occurs. This setting is used to select the interval between recall attempts. Note • If a transmission is still not successful after the set number of recall attempts is made, a report will print and the document will be cleared from memory.
PAGE 39
!AR-FX13_sec.book 35 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS When a communication error occurs You can select the interval between recall attempts when a communication error occurs. An interval from 0 to 15 minutes can be selected. If the recall interval is set to 0 minutes, the machine will immediately call again after breaking the connection due to the communication error. 1 Press the [MENU] key. 6 Press the [MENU] key. Press the [MENU] key to exit.
PAGE 40
!AR-FX13_sec.book 36 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING THE INDEX FUNCTION You can print an index mark along the edge of the pages in each job. This makes it easy to separate different jobs on the output tray. Separate faxes with index marks. Use the following procedure to set the index function: 1 Press the [MENU] key. 5 Press the [ENTER] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key. 6 Press the [MENU] key.
PAGE 41
!AR-FX13_sec.book 37 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING RESOLUTION PRIORITY For most faxing jobs, you will most likely want to specify the resolution. However, you can also set a default resolution when no setting is made using the [RESOLUTION] key. To turn on this function, follow the procedure below: 1 Press the [MENU] key. 6 Press the [MENU] key. Press the [MENU] key to exit.
PAGE 42
!AR-FX13_sec.book 38 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS SETTING UP THE MACHINE FOR USE WITH A PC MODEM The machine is set to automatically begin reception if you pick up from an extension telephone and the machine detects a fax tone. However, if you are using a modem on the same line, you must deactivate this function: otherwise the machine will mistakenly attempt to receive the transmission from your computer. To turn off the Fax Signal Receive function, follow the procedure below.
PAGE 43
!AR-FX13_sec.book 39 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS USING THE REMOTE RECEPTION FUNCTION The machines Remote Reception feature is designed to allow you to activate fax reception from an extension telephone. The Remote Reception function operates even when the FAX Signal Receive function is turned off. See "SETTING UP THE MACHINE FOR USE WITH A PC MODEM" on page 38. When you hear the fax tone, simply press the one-digit Fax Remote Number (Factory setting: 5) and .
PAGE 44
!AR-FX13_sec.book 40 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS Setting a Fax Remote Number: 1 Press the [MENU] key. 6 Press the [MENU] key. Press the [MENU] key to exit. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key. Selection "4:USER PROGRAM" 3 Press the [ ] key ( ) or [ ] key ( ) until "13:FAX REMOTE NUMBER" appears, and then press the [ENTER] key.
PAGE 45
!AR-FX13_sec.book 41 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS DISTINCTIVE RINGING Distinctive ringing is a service offered by some telephone companies that allows you to use up to six different telephone numbers, each with a distinctive ringing pattern, on your regular single line. If you subscribe to a distinctive ringing service, you can set your fax to automatically answer when it detects one of these ringing patterns, and use the number corresponding to that pattern as an exclusive fax number.
PAGE 46
!AR-FX13_sec.book 42 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS STORING NUMBERS FOR AUTOMATIC DIALING Automatic Dialing is a quick and convenient way to dial by using only a Rapid key (Rapid Key Dialing), or pressing the [SPEED/SEARCH] key and select the SPEED and entering a two digit number (Speed Dialing). To use Automatic Dialing, you must first store the full number.
PAGE 47
!AR-FX13_sec.book 43 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS 9 Enter the name of the destination with the numeric keys. Enter the name of the location or party by pressing numeric keys as described in "HOW TO ENTER CHARACTERS" on page 20 (maximum of 20 characters). If you do not want to enter a name, skip this step. 10 14 Press the [ENTER] key. 15 Press the [ ] key ( ) or [ to select the international communication mode. Press the [ENTER] key.
PAGE 48
!AR-FX13_sec.book 44 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS Use the following procedure to clear numbers: 1 6 Press the [MENU] key. Enter the Rapid Key or Speed Dial number that you wish to delete. To delete a Rapid Key, press the appropriate Rapid key. To delete a Speed Dial number, enter the 2-digit number with the numeric keys and then press the [ENTER] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "2:ENTRY MODE" appears, and then press the [ENTER] key. 7 Press the [ENTER] key.
PAGE 49
!AR-FX13_sec.book 45 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS STORING NUMBERS UNDER GROUP KEYS Group keys allow you to dial a group of fax numbers by simply pressing the appropriate Group key once. They are convenient for the Broadcasting function, which is used to transmit an original to a group of fax machines. All Rapid keys can be programmed as Group keys. To program or clear a group key, follow the steps below.
PAGE 50
!AR-FX13_sec.book 46 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS 9 Enter a name for the Group Key with the numeric keys. Enter the name of the group by pressing numeric keys as described in "HOW TO ENTER CHARACTERS" on page 20 (maximum of 20 characters). If you do not want to enter a name, skip this step. To add numbers: The entered name appears. Edit the name if you need to make a change. 10 Press the [ENTER] key. Return to Step 7 to program another Group key. 11 Press the [MENU] key.
PAGE 51
!AR-FX13_sec.book 47 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS Deleting numbers from Group Keys: 1 Press the [MENU] key. 7 Enter the numbers that you wish to delete. Enter the fax numbers using any of the following methods: • Press a Rapid Key. • Enter a Speed Dial number with the numeric keys. • Enter a number with the numeric keys. 2 Press the [ ] key ( ) or [ ] key ( ) until "2:ENTRY MODE" appears, and then press the [ENTER] key. 8 Press the [ENTER] key.
PAGE 52
!AR-FX13_sec.book 48 ページ２００９年５月１１日　月曜日　午後２時２４分 USING THE MACHINE WITH AN ANSWERING MACHINE QUIET DETECT TIME Quiet Detect Time is the function that enables the machine to be used along with an answering machine for both phone messages and faxes. After the answering machine has answered, any duration of silence longer than a certain threshold time will prompt the machine to take over the line and prepare to receive a fax.
PAGE 53
!AR-FX13_sec.book 49 ページ２００９年５月１１日　月曜日　午後２時２４分 INITIAL SETTINGS If Quiet Detect Time is not working properly... With some answering machines, there is simply no Quiet Detect Time that will allow both reception of faxes and uninterrupted voice messages. Even in this case, however, you can set up the machine to receive both phone and fax messages from callers on touch-tone lines. Follow this procedure: 1. Set the Quiet Detect Time to 00. 2.
PAGE 54
!AR-FX13_sec.book 50 ページ２００９年５月１１日　月曜日　午後２時２４分 Chapter 3 3 CHOOSING SUITABLE MEDIA ORIGINALS SUITABLE FOR FAXING Make sure that the originals you want to fax meet specifications and guidelines listed in this section. SIZE AND WEIGHT The size and weight of originals that you can load in the RSPF depend on whether you load one sheet at a time or several sheets at once. When using the RSPF 14 lbs. (56 /m2) 24 lbs. (90.3 /m2) One-sided original : 19.
PAGE 55
!AR-FX13_sec.book 51 ページ２００９年５月１１日　月曜日　午後２時２４分 CHOOSING SUITABLE MEDIA UNSUITABLE ORIGINALS General guidelines: ● All clips, staples, and pins should be removed from originals before they are used. If these are not removed, they may damage the machine. ● Ink, glue, and correction fluid on originals must be completely dry before using the originals with the machine. ● Originals that are in some way dangerous to the internal mechanisms of the machine should not be used.
PAGE 56
!AR-FX13_sec.book 4 52 ページ２００９年５月１１日　月曜日　午後２時２４分 Chapter 4 HOW TO USE THE FAX FUNCTION The machine offers a range of sophisticated features that allow you to control image quality, reception mode, broadcasting, polling, and transmission priorities. Functions such as sending original(s) from memory and substituting reception into memory are possible, due to the large memory capacity.
PAGE 57
!AR-FX13_sec.book 53 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION When placing the Original on the document glass: 1 2 Confirm that there are no original(s) in the RSPF, and open the RSPF. 5 Press the [START] key ( The set original size appears in the display and then scanning begins. Place the original face down on the document glass. Align the original according to the original scale in the illustration below. (Line up the center of the edge of the original with the ( ) mark.
PAGE 58
!AR-FX13_sec.book 54 ページ２００９年５月１１日　月曜日　午後２時２４分 OPTIONAL TRANSMISSION SETTINGS There are several transmission settings that you can make before dialing and transmitting an original. ORIGINAL SIZE The original size can be set to "8.5x11", "8.5x14", or "A4". The setting is only effective for one transmission. If desired, you can set a fixed original size that remains in effect for all transmissions. 1 Press the [MENU] key. 5 Press the [ENTER] key.
PAGE 59
!AR-FX13_sec.book 55 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION RESOLUTION To do this, press the [RESOLUTION] key one or more times until the desired resolution settings appear in the display, and then press the [ENTER] key. Your fax has five resolution settings: • STANDARD Use STANDARD for ordinary originals. This setting gives you the fastest transmission. • FINE Use FINE for improved reproduction, especially with originals containing small letters or fine drawings.
PAGE 60
!AR-FX13_sec.book 56 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION COVER SHEET You can have your fax generate a cover sheet and send it as the last page of the transmission. The cover sheet includes the date and time, the sender's name and number, and the receiver's name and number if an automatic dialing number is used. The total number of pages sent is indicated on the bottom. One of five messages can also be added to the cover sheet.
PAGE 61
!AR-FX13_sec.book 57 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION MESSAGE FUNCTION One of the following messages can be selected: "CONFIDENTIAL", "PLS. DISTRIBUTE", "URGENT", "PLS. CALL BACK", "IMPORTANT". Note If a message is selected when the cover sheet function is not used, the message will be added to the top of the first page of the fax. To add a message to a cover sheet, follow these steps: 1 Press the [COVER SHEET] key.
PAGE 62
!AR-FX13_sec.book 58 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION TWO-SIDED ORIGINAL TRANSMISSION FUNCTION The RSPF can be used to automatically fax a two-sided original. If desired, the back of the original can be rotated 180° before transmission. Note • The original must be placed in the RSPF when using the two-sided original transmission function. The document glass cannot be used. • The two-sided original transmission function cannot be selected when direct transmission mode is selected.
PAGE 63
!AR-FX13_sec.book 59 ページ２００９年５月１１日　月曜日　午後２時２４分 DIALING AND TRANSMITTING Once you have set the original (either in the RSPF or on the document glass), and have selected the desired transmission settings, you are ready to dial the number of the receiving fax machine and transmit the original. You can choose from one of the several ways of dialing that best suit your needs.
PAGE 64
!AR-FX13_sec.book 60 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION CHAIN DIALING The Chain Dialing function allows you to combine a Rapid Key or Speed Dial number (See "STORING NUMBERS FOR AUTOMATIC DIALING" (p.42)) set for Chain Dialing with another Rapid Key, Speed Dial number, or number dialed with the numeric keys to dial one fax number up to 50 digits long.
PAGE 65
!AR-FX13_sec.book 61 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION USING THE SEARCH KEY If you do not remember the Rapid key or Speed Dial number in which you have stored a particular fax number, you can search for the number by following the steps below: 1 Press the [SPEED/SEARCH] key twice. 2 Enter the first letter of the stored name by pressing the appropriate numeric key (the key below the marked letter) until the letter appears in the display.
PAGE 66
!AR-FX13_sec.book 62 ページ２００９年５月１１日　月曜日　午後２時２４分 IF THE MEMORY BECOMES FULL WHILE SCANNING AN ORIGINAL If the memory becomes full while scanning an original, "MEMORY FULL ERROR" will appear in the display and scanning will stop. If the memory becomes full while the first page is being scanned, scanning will stop and the transmission will be canceled. If the memory becomes full while scanning a page after the first page, scanning will stop.
PAGE 67
!AR-FX13_sec.book 63 ページ２００９年５月１１日　月曜日　午後２時２４分 RECEIVING FAXES You can set the machine to one of three modes of reception, AUTO, MAN. , or A.M. (Answering Machine). To select the reception mode, press the [RECEPTION MODE] key until the desired reception mode appears in the display. NOV 05 WED 8:20 AM STAD-BY AUTO 100% USING AUTO MODE Select AUTO mode when you only want to receive faxes on your telephone line. The machine will automatically answer all calls and receive incoming faxes. USING MAN.
PAGE 68
!AR-FX13_sec.book 64 ページ２００９年５月１１日　月曜日　午後２時２４分 OPTIONAL RECEPTION SETTINGS The machine has various optional settings for the reception of faxes. TWO-SIDED RECEPTION This function is used to print a received fax consisting of two or more pages of the same size on both sides of the paper. Even if the pages are in different orientations, the pages are rotated appropriately to enable printing on both sides of the paper.
PAGE 69
!AR-FX13_sec.book 65 ページ２００９年５月１１日　月曜日　午後２時２４分 HOW TO USE THE FAX FUNCTION RECEIVE REDUCE You may on occasion receive faxes that are larger than the paper loaded in the machine. To ensure that you do not lose any part of the original, you should use the Receive Reduce function, which scales the fax to the printing paper size. Note In some cases the size or resolution of a received fax may not permit reduction.
PAGE 70
!AR-FX13_sec.book 66 ページ２００９年５月１１日　月曜日　午後２時２４分 WHEN USING MANUAL SENDING AND RECEIVING You need to use the [SPEAKER] key or an extension telephone to perform manual sending and receiving. For information about connecting an extension telephone See "CONNECTING OTHER DEVICES" (p.12). 1 When the extension telephone rings, pick up the handset and converse. If the [SPEAKER] key is used to answer a call you cannot converse.
PAGE 71
!AR-FX13_sec.book 5 67 ページ２００９年５月１１日　月曜日　午後２時２４分 Chapter 5 SPECIAL FUNCTIONS MEMORY Your machine has a memory area that can be used to store both incoming faxes and outgoing originals. ● Approximately 120 pages of average content can be held in memory for transmission and reception. Less can be held if any of the pages were scanned using fine or superfine resolution.
PAGE 72
!AR-FX13_sec.book 68 ページ２００９年５月１１日　月曜日　午後２時２４分 DATA TRANSFER If there is a problem with the machine, you can use the Data Transfer function to have received faxes read into memory and then sent to a different fax machine for printing. This function is used when you cannot print received faxes, for example when the machine runs out of toner, or a misfeed occurs. To use this function, the fax number of the transfer destination machine must be programmed.
PAGE 73
!AR-FX13_sec.book 69 ページ２００９年５月１１日　月曜日　午後２時２４分 SPECIAL FUNCTIONS Follow these steps to use the fax transfer function: 1 Press the [MENU] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "0:RX DATA TRANSFER" appears, and then press the [ENTER] key. Selection "0:RX DATA TRANSFER" 3 Press the [ ] key ( ) or [ ] key ( ) until "1:DATA TRANSFER" appears, and then press the [ENTER] key.
PAGE 74
!AR-FX13_sec.book 70 ページ２００９年５月１１日　月曜日　午後２時２４分 TRANSMISSION RESERVATION When your fax is busy receiving an original or transmitting an original from memory, you can "reserve" a transmission by setting the original (either in the RSPF or on the document glass), reading it into memory, and entering the fax number. Once the current operation is completed, your fax will automatically dial the number and transmit the original saving you from having to wait.
PAGE 75
!AR-FX13_sec.book 71 ページ２００９年５月１１日　月曜日　午後２時２４分 BROADCASTING This function allows you to send the same original to as many as 100 different locations with just one operation. Once the original is loaded, it is scanned and stored in memory. The fax numbers you have entered are then automatically dialed in succession, and the original is transmitted to each location.
PAGE 76
!AR-FX13_sec.book 72 ページ２００９年５月１１日　月曜日　午後２時２４分 SPECIAL FUNCTIONS Broadcasting using a Group key If the fax machines to which you want to broadcast have all been programmed into one Group key, you can perform the broadcasting operation using the following simplified procedure. Refer to "STORING NUMBERS UNDER GROUP KEYS" (p.45). 1 Place the original face up and push it gently into the document feeder tray. Original face up 2 Adjust the resolution and/or contrast settings if desired.
PAGE 77
!Chapter05.fm 73 ページ２００９年５月１４日　木曜日　午後７時３９分 POLLING Polling allows you to request another fax machine to send an original to your fax machine. In other words, the receiving fax machine, not the transmitting fax machine, activates the transmission. You can use your fax to both poll and be polled by others. Serial polling can be used to poll multiple fax machines (maximum of 100) in a single operation. POLLING You can request that another fax machine send you the original that is set in that fax machine.
PAGE 78
!Chapter05.fm 74 ページ２００９年５月１４日　木曜日　午後７時３９分 SPECIAL FUNCTIONS SERIAL POLLING You can poll several fax machines one at a time with a single serial polling operation. A maximum of 100 fax machines can be polled in one serial polling operation.
PAGE 79
!Chapter05.fm 75 ページ２００９年５月１４日　木曜日　午後７時３９分 SPECIAL FUNCTIONS POLLING TRANSMISSION (MEMORY POLLING) This function is used to transmit an original that has been scanned into memory to a fax machine that polls your fax machine. If desired, polling fax machines can be restricted to machines whose fax numbers have been programmed in your machine ("RESTRICTING POLLING MACHINES (POLLING SECURITY)" on page 77).
PAGE 80
!Chapter05.fm 76 ページ２００９年５月１４日　木曜日　午後７時３９分 SPECIAL FUNCTIONS Adding a original to polling memory: Deleting originals from polling memory: Use this procedure to add an original to another original that has already been scanned into polling memory. Place the original in the RSPF or on the document glass and follow the steps below. Follow the steps below to delete originals that have been scanned into polling memory. 1 Press the [MENU] key. 1 Press the [MENU] key.
PAGE 81
!Chapter05.fm 77 ページ２００９年５月１４日　木曜日　午後７時３９分 SPECIAL FUNCTIONS RESTRICTING POLLING MACHINES (POLLING SECURITY) If you wish to allow only specified fax machines to poll your fax machine, enable polling security and program the fax numbers of the machines that are to be allowed to poll your machine. When this is done, polling will take place when the fax number of the polling machine matches one of the fax numbers that have been programmed in your machine.
PAGE 82
!AR-FX13_sec.book 78 ページ２００９年５月１１日　月曜日　午後２時２４分 SPECIAL FUNCTIONS Programming/deleting passcode numbers: 1 Press the [MENU] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "2:ENTRY MODE" appears, and then press the [ENTER] key. Selection Press the [ ] key ( ) or [ ] key ( ) until "4:PASSCODE # MODE" appears, and then press the [ENTER] key. Selection "4:PASSCODE # MODE" 4 Press the [ ] key ( ) or [ ] key ( to select "1:SET" and press the [ENTER] key.
PAGE 83
!AR-FX13_sec.book 79 ページ２００９年５月１１日　月曜日　午後２時２４分 TIMER OPERATIONS The timer function allows you to set a transmission or polling operation to be performed automatically at a time you specify. Up to five transmission operations or polling operations can be set at any one time, and the times they will be performed can be specified up to a week in advance. You can use this function, for example, to take advantage of lower night time telephone rates without having to be there when the operation is performed.
PAGE 84
!AR-FX13_sec.book 80 ページ２００９年５月１１日　月曜日　午後２時２４分 SPECIAL FUNCTIONS 6 Press the [ ] key ( ) or [ ] key ( to select the day of the week and press the [ENTER] key. ) 9 Enter the fax number of the other machine using one of the following methods: • Press a Rapid key. If you press a Rapid Key, the next step is not necessary. • Enter a Speed Dial number with the numeric keys. • Enter the fax number with the numeric keys. 10 7 Press the [ENTER] key.
PAGE 85
!AR-FX13_sec.book 81 ページ２００９年５月１１日　月曜日　午後２時２４分 ANTI JUNK FAX You can avoid wasting fax paper by using the Anti Junk Fax function. This function blocks reception of faxes from up to ten specified parties. To turn the Anti Junk Fax feature on and off, use the following procedure: 1 Press the [MENU] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "5:ANTI JUNK FAX" appears, and then press the [ENTER] key.
PAGE 86
!AR-FX13_sec.book 82 ページ２００９年５月１１日　月曜日　午後２時２４分 SPECIAL FUNCTIONS To store junk fax numbers, use the following procedure: 1 Press the [MENU] key. 5 2 Press the [ ] key ( ) or [ ] key ( ) until "5:ANTI JUNK FAX" appears, and then press the [ENTER] key. Note Selection "5:ANTI JUNK FAX" 3 Press the [ ] key ( ) or [ ] key ( ) to select "2:JUNK FAX #" and press the [ENTER] key. Enter a two-digit number from 01 to 10 that will identify the anti junk number and press the [ENTER] key.
PAGE 87
!AR-FX13_sec.book 83 ページ２００９年５月１１日　月曜日　午後２時２４分 SPECIAL FUNCTIONS To clear junk fax numbers, use the following procedure: 1 6 Press the [MENU] key. Press the [ENTER] key. If you wish to store another fax number, return to step 5. 2 Press the [ ] key ( ) or [ ] key ( ) until "5:ANTI JUNK FAX" appears, and then press the [ENTER] key. 7 Press the [MENU] key. Press the [MENU] key to exit.
PAGE 88
!AR-FX13_sec.book 84 ページ２００９年５月１１日　月曜日　午後２時２４分 OPERATION IN COPY, PRINTER, SCANNER, AND FAX MODES Some operations cannot be performed simultaneously when the machine is being used in printer mode, copy mode, scanner mode, and fax mode.
PAGE 89
!Chapter06.fm 6 85 ページ２００９年５月１１日　月曜日　午後５時３分 Chapter 6 TROUBLESHOOTING PRINTING OUT REPORTS The machine is capable of printing a range of reports on faxing activities as well as various settings you have made. The reports are described below. 1. TIMER LIST: You can print a list of timer or dual access operations that are currently set. P. 01 TIMER LIST SEP-10-200X FRI 06:30 PM TIMER MODE TYPE FILE RESERVED RES.
PAGE 90
!Chapter06.fm 86 ページ２００９年５月１１日　月曜日　午後５時３分 TROUBLESHOOTING 5. PASSCODE LIST: You can print a list of your fax information and polling security information. PASSCODE LIST SEP-10-200X FRI 06:30 PM POLL SECURITY SYSTEM # XXXX XXXX ID # 01 XXXX 02 XXXX 03 04 05 06 07 08 09 10 PASSCODE # 01 XXXXXXXXXX 02 XXXXXXXXXX 03 04 05 06 07 08 09 10 SENDER'S NAME XXXXXXXXXXXXXXXXXX SENDER'S # XXXXXXXXXXXXXXXX FW. STA. NAME XXXXXXXXXXXXXXXXXXXX FW. STATION # XXXXXXXXXXXXXXXX 6.
PAGE 91
!Chapter06.fm 87 ページ２００９年５月１１日　月曜日　午後５時３分 TROUBLESHOOTING 7. USER PROGRAM LIST: Currently activated USER PROGRAM settings. USER PROGRAM LIST S EP -10-200X F R I 06: 30 P M ITEM MENU # SETTING 1 DOC. GLASS SIZE 8.5x11 2 FIXED DOC. SIZE 8.5x11 3 RESO.
PAGE 92
!AR-FX13_sec.book 88 ページ２００９年５月１１日　月曜日　午後２時２４分 TROUBLESHOOTING ACTIVITY REPORT AUTO LISTING This setting is used to automatically print the Activity Report for transmissions and receptions. The Activity Report will automatically print when information on a total of 50 fax transmissions and receptions accumulates. Once information on 50 transmissions/receptions accumulates, the oldest transaction is deleted each time a new transaction takes place. 1 Press the [MENU] key.
PAGE 93
!AR-FX13_sec.book 89 ページ２００９年５月１１日　月曜日　午後２時２４分 TROUBLESHOOTING PRINTING TRANSACTION REPORTS The machine can be set to print a transaction report after each transmission, reception, and/or error. The printing condition can be selected separately for three types of transaction reports: "TRANSMISSION LIST", "BROADCAST LIST", and "RECEPTION LIST". For each type of report, select one of the following printing conditions: "ALWAYS PRINTS" ...After each transmission, reception, or error. "ERROR ONLY".........
PAGE 94
!AR-FX13_sec.book 90 ページ２００９年５月１１日　月曜日　午後２時２４分 TROUBLESHOOTING Problem Dialing cannot be done. No transmission takes place. Nothing is printed at the receiving end. Cause and solution The telephone line cord is not correctly connected to the machine and the wall telephone jack. → Make sure the telephone line cord is securely connected. Page 11 The receiving machine is out of paper. → Check with the operator of the receiving machine. - The receiving machine does not support the G3 standard.
PAGE 95
!AR-FX13_sec.book 91 ページ２００９年５月１１日　月曜日　午後２時２４分 MESSAGES AND SIGNALS DISPLAY MESSAGES Message Cause and remedy Page FRONT OR SIDE COVER OPEN. The cover is open. Close the cover. CLOSE COVERS. See the OPERATION MANUAL (for general information) CLOSE THE SPF/RSPF COVER. The RSPF cover is open. Close the RSPF cover. CLEAR PAPER JAM. SPF/RSPF JAM. A paper misfeed has occurred. Remove the misfeed as explained in "MISFEED REMOVAL". (See the OPERATION MANUAL for general information.
PAGE 96
!AR-FX13_sec.book 92 ページ 7 ２００９年５月１１日　月曜日　午後２時２４分 Chapter 7 APPENDIX SPECIFICATIONS Applicable telephone line Public switched telephone network Compression method MH, MR, MMR, JBIG Transmission modes Super G3, G3 (the machine can only send faxes to and receive faxes from machines that support G3 or Super G3) Scanning method CCD flatbed scanning Scanning resolution (supports ITU-T standards) 8 x 3.85 lines/mm (Standard) 8 x 7.7 lines/mm (Fine, Fine + Halftone) 8 x 15.
PAGE 97
!AR-FX13_sec.book 93 ページ２００９年５月１１日　月曜日　午後２時２４分 INDEX A Alarm beeps - Alarm beep volume .......................................... 19 - Length of alarm beeps ..................................... 18 Answering machine................................................. 48 - Answering machine backup ............................. 49 - Quiet detect time .............................................. 48 Arrow keys ........................................................ 15, 16 Automatic dialing - Group keys.....
PAGE 98
!AR-FX13_sec.book 94 ページ２００９年５月１１日　月曜日　午後２時２４分 R Receiving faxes....................................................... 63 - Receive reduce ................................................ 65 - Two-sided reception......................................... 64 Reception mode - A.M. mode.................................................. 27, 63 - AUTO mode ............................................... 27, 63 - MAN. mode ................................................ 27, 63 Remote reception...............
PAGE 99
!AR-FX13_sec.book 95 ページ２００９年５月１１日　月曜日　午後２時２４分 INDEX BY PURPOSE Fax setup Storing/settings Connecting the telephone line cord......................... 11 Daylight saving time setting .................................... 25 Dial mode ................................................................ 31 Distinctive ringing .................................................... 41 Entering your name and fax number....................... 21 How to enter characters ..........................................
PAGE 100
!AR-FX13_sec.
PAGE 101
!AR-FX13_sec.
PAGE 102
!AR-FX13_sec.
PAGE 103
!AR-FX13_sec.
PAGE 104
!AR-FX13_sec.book 1 ページ２００９年５月１１日　月曜日　午後２時２４分 FO-2080 OPERATION MANUAL (for facsimile) SHARP ELECTRONICS CORPORATION 1 Sharp Plaza, Mahwah, New Jersey 07495-1163. www.sharpusa.com This manual has been printed using a vegetable-based soy oil ink to help protect the environment.