MODEL -DC550 MODEL ULTIFUNCTIONAL SYSTEM TION MANUAL eral information) IONS APER OPIES NT COPY S Page 9 14 20 E SOFTWARE 26 36 CANNER S 57 INGS FO-DC550 62 HOOTING AND NCE 69 EQUIPMENT 92 94 ED IN CHINA 04E KS1 SE1323QSZZ DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL (for general information) Page PREPARATIONS LOADING PAPER MAKING COPIES CONVENIENT COPY FUNCTIONS 9 14 20 SET UP THE SOFTWARE 26 36 PRINTER/SCANNER FUNCTIONS 57 USER SETTINGS 62 TROUBLESHOOTING AND MAINTENANCE 6
FO-DC550_Copy(Sec).book 0 ページ 2004年3月25日 木曜日 午後3時44分 FOR YOUR RECORDS ... To protect against loss theft, record and retain for reference the copier's serial number located on the back of the unit. Model Number Serial Number Date of Purchase Authorized Sharp Copier Service Department Number NOTICE BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU.
FO-DC550_Copy(Sec).book 1 ページ 2004年3月25日 木曜日 午後3時44分 CONTENTS CAUTIONS ................................................................................................................ 3 ENVIRONMENTAL INFORMATION ......................................................................... 5 INTRODUCTION ....................................................................................................... 6 MAIN FEATURES ......................................................................................
FO-DC550_Copy(Sec).book 2 ページ 2004年3月25日 木曜日 午後3時44分 6 PRINTER/SCANNER FUNCTIONS USING THE PRINTER MODE ........................................................................ 58 BASIC PROCEDURE FOR PRINTING ........................................................... 58 USING THE SCANNER MODE....................................................................... 59 SCANNING USING THE KEYS ON THE MACHINE ...................................... 59 SCANNING FROM YOUR COMPUTER .............................
FO-DC550_Copy(Sec).book 3 ページ 2004年3月25日 木曜日 午後3時44分 CAUTIONS Caution label on the machine The label ( ) in the fusing area of the machine indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using the machine Follow the cautions below when using this machine. Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes.
!002-Cautions.fm 4 ページ 2004年3月26日 金曜日 午前8時42分 Cautions on handling the machine Be careful in handling the machine as follows to maintain the performance of this machine. Do not drop the machine, subject it to shock or strike it against any object. Do not expose the drum cartridge to direct sunlight. • Doing so will damage the surface (green portion) of the drum cartridge, causing smudges on copies.
FO-DC550_Copy(Sec).book 5 ページ 2004年3月25日 木曜日 午後3時44分 ENVIRONMENTAL INFORMATION As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Safety precautions: This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the unit does not produce hazardous laser radiation. For your safety, observe the precautions below.
FO-DC550_Copy(Sec).book 6 ページ 2004年3月25日 木曜日 午後3時44分 INTRODUCTION Using the manual This machine has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all machine features, be sure to familiarize yourself with this manual and the machine. For quick reference during machine use, keep this manual in a handy location.
FO-DC550_Copy(Sec).book 7 ページ 2004年3月25日 木曜日 午後3時44分 MAIN FEATURES High-speed laser copying First-copy time*1 at 300 dpi*2 is only 9.6 seconds. Copying speed is 16 copies per minute. This is ideal for business use and provides a big boost to workplace productivity. *1 The copy time in the case when the power is turned on and copying using the document glass is started immediately after the power save indicator goes off (8-1/2" x 11", paper fed from paper tray).
FO-DC550_Copy(Sec).book 8 ページ 2004年3月25日 木曜日 午後3時44分 Fax function • The machine is equipped with a plain paper laser fax function that is Super G3 compatible and includes a print hold feature. (Operation Manual for facsimile) Laser printer function • The accompanying printer driver can be installed to enable use of the machine as a printer. Color scanner function • The accompanying scanner driver can be installed and the machine connected to a computer using a USB cable to enable use as a scanner.
FO-DC550_Copy(Sec).book 1 9 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 1 PREPARATIONS This chapter provides basic information that you should know before using the machine.
!01-Introduction.fm 10 ページ 2004年3月25日 木曜日 午後4時57分 PREPARATIONS Operation panel 1 Keys for fax function (See the Operation Manual for facsimile.) 1 2 3 4 5 6 7 10 [MODE SELECT] key / Mode indicators Press this key to select the mode. The indicator of the selected mode lights (copy, printer, scanner, fax mode indicators). Display This shows messages indicating the machine status and any problems that occur, as well as user programs and function setting menus.
!01-Introduction.fm 11 ページ 2004年3月25日 木曜日 午後4時54分 PREPARATIONS 3 4 5 1 Display READY TO COPY. 100% 8.5x11 16 17 18 [COPY RATIO] key Press to select an enlargement or reduction ratio. To select a preset ratio setting, press the [COPY RATIO] key and select the desired preset ratio.
FO-DC550_Copy(Sec).book 12 ページ 2004年3月25日 木曜日 午後3時44分 POWER ON AND OFF The power switch is located on the left side of the machine. If you use the machine in a country other than the country Warning where the machine was purchased, you will need to make sure that your local power supply is compatible with your model. If you plug the machine into an incompatible power supply, irreparable damage to the machine will result. Power on Turn the power switch to the "ON" position.
FO-DC550_Copy(Sec).book 13 ページ 2004年3月25日 木曜日 午後3時44分 PREPARATIONS About the scan head The scan head lamp remains on constantly when the machine is in the ready condition (when the ready indicator is illuminated). The machine adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not indicate machine trouble. 1 Power off Note Normally keep in the "ON" position when using the fax function.
FO-DC550_Copy(Sec).book 2 14 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 2 LOADING PAPER The tray location indicator will blink when there is no paper in the selected paper tray, or when the selected paper tray is not closed or is improperly closed. PAPER For best results, use only SHARP recommended paper. Paper tray type Paper type Size Weight *1 Capacity Paper tray Standard paper 5-1/2" x 8-1/2" 15 lbs. to 21 lbs.
FO-DC550_Copy(Sec).book 15 ページ 2004年3月25日 木曜日 午後3時44分 LOADING PAPER Special papers Follow these guidelines when using special papers. ● Use SHARP recommended transparency film and label sheets. Using other than SHARP recommended paper may result in misfeeds or smudges on the output. If other than SHARP recommended media must be used, feed each sheet one at a time using the bypass tray (do not attempt continuous copying or printing).
FO-DC550_Copy(Sec).book 16 ページ 2004年3月25日 木曜日 午後3時44分 LOADING PAPER 3 Fan the paper and insert it into the tray. Make sure that the edges go under the corner hooks. Note 4 Gently push the paper tray back into the machine. Note 16 • Do not load paper above the maximum height line ( ). Exceeding the line will cause a paper misfeed. • If the paper is not fanned, double-feeds or misfeeds may occur. • Make sure the stack of paper is straight before loading it.
FO-DC550_Copy(Sec).book 17 ページ 2004年3月25日 木曜日 午後3時44分 BYPASS FEED (including special paper) The bypass tray can be used to feed standard paper, transparency film, labels, envelopes, and other special purpose paper. Important points when inserting paper in the bypass tray Up to 50 sheets of standard copy paper can be inserted in the bypass tray. (Capacity will vary depending on the type of paper loaded.) Be sure to place envelopes horizontally as shown in the following diagram.
FO-DC550_Copy(Sec).book 18 ページ 2004年3月25日 木曜日 午後3時44分 LOADING PAPER Loading paper in the bypass tray Note 1 Open the bypass tray and extend the tray. Note 2 • Paper must be fed narrow side first into the feed slot. • Special papers such as transparency film, labels, and envelopes must be fed one sheet at a time through the bypass tray. • When copying onto transparency film, remove each copy promptly. Do not let copies stack up.
FO-DC550_Copy(Sec).book 19 ページ 2004年3月25日 木曜日 午後3時44分 CHANGING A TRAY'S PAPER SIZE SETTING Follow these steps to change a tray's paper size setting. Note • The paper size setting cannot be changed when the machine has stopped temporarily due to running out of paper or a misfeed. • During printing (even in copy mode), the paper size setting cannot be changed. 1 Press the [MENU] key. Press the [ ] key ( ) or [ ] key ( ) until "PAPER SIZE" appears, and then press the [ENTER] key.
FO-DC550_Copy(Sec).book 3 20 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 3 MAKING COPIES This chapter explains basic copying functions. NORMAL COPYING Using the document glass Note 1 • The document glass can scan up to 8-1/2" x 14" original. • When a copy is made, the edges will not be copied (image loss). For the image loss, see the "SPECIFICATIONS" (p.94). Open the RSPF, and place the original face down on the document glass.
FO-DC550_Copy(Sec).book 21 ページ 2004年3月25日 木曜日 午後3時44分 MAKING COPIES Using the RSPF Note • Originals that are 5-1/2" x 8-1/2" to 8-1/2" x 14" and 14 lbs. to 24 lbs. (52 g/m2 to 90 g/m2) can be used. A maximum of 30 pages can be placed at once. • Straighten curled originals before placing them in the document feeder tray. Curled originals may cause misfeeds. • Place originals horizontally. • Before placing originals in the document feeder tray, be sure to remove any staples or paper clips from them.
!03-making copies.fm 22 ページ 2004年3月25日 木曜日 午後4時36分 MAKING COPIES Originals that cannot be used in the RSPF The following originals cannot be used. These may cause misfeeds or smudging and unclear images.
FO-DC550_Copy(Sec).book 23 ページ 2004年3月25日 木曜日 午後3時44分 MAKING COPIES Setting the number of copies Press the numeric keys to set the number of copies. OPY. x11 55 The set number of copies appears in the display. A maximum of 99 copies can be set. If you wish to make only a single copy, copying is possible with the display showing "0". Note If you enter the wrong number, press the [CLEAR] key ( enter the correct number. ) and 3 SELECTING THE TRAY Press the [TRAY SELECT] key ( ).
FO-DC550_Copy(Sec).book 24 ページ 2004年3月25日 木曜日 午後3時44分 MAKING A COPY DARKER OR LIGHTER Automatic exposure adjustment is initially enabled. This function automatically adjusts the copy image according to the original being copied. If you wish to select the exposure level yourself, follow the steps below. (Select from two original types and five exposure levels for each original type.
FO-DC550_Copy(Sec).book 25 ページ 2004年3月25日 木曜日 午後3時44分 REDUCTION/ENLARGEMENT/ZOOM Copies can be reduced down to 25% or enlarged up to 400%. (When the RSPF is being used, the zoom copy ratio range is 50% to 200%.) The [COPY RATIO] key can be pressed to quickly select a ratio from among eight preset ratios. In addition, the [ ] key ( ) and [ ] key ( ) can be pressed to select the ratio in increments of 1%. 1 Place the original(s) and check the paper size. 2 Press the [COPY RATIO] key.
FO-DC550_Copy(Sec).book 4 26 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 4 CONVENIENT COPY FUNCTIONS AUTOMATIC TWO-SIDED COPYING Two originals can be automatically copied onto both sides of a single sheet of paper. When the RSPF is used, two-sided copies of two-sided originals can easily be made.
FO-DC550_Copy(Sec).book 27 ページ 2004年3月25日 木曜日 午後3時44分 CONVENIENT COPY FUNCTIONS Using the document glass 1 Place the original that you wish to copy onto the front side of the paper on the document glass and close the RSPF. 2 Press the [2-SIDED COPY] key until "1 TO 2" appears, and then press the [ENTER] key. 3 Press the [ ] key ( ) or [ ] key ( ) to select the binding edge and then press the [ENTER] key. 2-SIDED COPY 1 TO 2 BINDING EDGE LONG EDGE Select "LONG EDGE" or "SHORT EDGE".
FO-DC550_Copy(Sec).book 28 ページ 2004年3月25日 木曜日 午後3時44分 CONVENIENT COPY FUNCTIONS Using the RSPF 1 Place the original(s) in the RSPF. (p.21) If you place an odd number of originals for one-sided to two-sided copying, the last page will be one-sided. 2 Press the [2-SIDED COPY] key and select the two-sided copy mode that you wish to use.
FO-DC550_Copy(Sec).book 29 ページ 2004年3月25日 木曜日 午後3時44分 SORT COPY Copies of multiple original pages can be sorted into sets. Note The number of pages that can be scanned varies depending on the original type (photo, text, etc.) and the amount of memory allocated to the printer. The amount of memory allocated to the printer can be changed with "MEM. FOR PRINTER" in the user programs. (p.64) 1 2 3 3 1 2 3 2 1 1 2 3 Sort copy Using the document glass 1 Place the first original. (p.
FO-DC550_Copy(Sec).book 30 ページ 2004年3月25日 木曜日 午後3時44分 CONVENIENT COPY FUNCTIONS Using the RSPF 1 Place the originals. (p.21) • If "SORT AUTO SELECT" is enabled in the user programs, the default output mode for copying from the RSPF is sort mode (p.65). In this case go directly to step 4. A checkmark " " will automatically appear in the display (p.11). • If "SORT AUTO SELECT" is disabled, the default output mode will be nonsort mode. Follow the steps below to select sort mode.
FO-DC550_Copy(Sec).book 31 ページ 2004年3月25日 木曜日 午後3時44分 COPYING MULTIPLE ORIGINALS ONTO A SINGLE (2 IN 1 copy) SHEET OF PAPER Multiple originals can be copied onto a single sheet of paper in a selected layout pattern. This function is convenient for compiling multi-page reference materials into a compact format, or for providing an overview of all pages of a document on a single page.
FO-DC550_Copy(Sec).book 32 ページ 2004年3月25日 木曜日 午後3時44分 CONVENIENT COPY FUNCTIONS 4 Press the [ ] key ( ) or [ ] key ( ) to select the original size and then press the [ENTER] key. ORIG. SIZE ENTER 5.5x8.5 The following original sizes can be selected: "8.5x14", "8.5x13", "8.5x11", "5.5x8.5", "A4", "B5", "A5". 5 Select the number of copies and any other settings, and then press the [START] key ( ). "[START] : NEXT SCAN [#] : START PRINT" appears and the original is scanned into memory.
FO-DC550_Copy(Sec).book 33 ページ 2004年3月25日 木曜日 午後3時44分 CONVENIENT COPY FUNCTIONS Using the RSPF 1 Place the originals. (p.21) 2 Press the [E-SORT/SP.FUN] key until "2IN1" appears and then press the [ENTER] key. 3 Press the [ ] key ( ) to move " " to the "ON" position and then press the [ENTER] key. 4 Press the [ ] key ( ) or [ ] key ( ) to select the original size and then press the [ENTER] key. SPECIAL FUNCTION 2IN1 2IN1 ON OFF ORIG. SIZE ENTER 5.5x8.
FO-DC550_Copy(Sec).book 34 ページ 2004年3月25日 木曜日 午後3時44分 CREATING MARGINS WHEN COPYING (Margin shift) The margin shift function is used to automatically shift the text or image or the copy paper approximately 1/2". As shown below, LONG EDGE or SHORT EDGE can be selected. AB SHORT EDGE RSPF BA LONG EDGE AB AB Margin Margin Copy Document glass Original Note 34 • This feature cannot be used with the 2 IN 1 feature. • The margin width can be changed with "MARGIN WIDTH" in the user programs. (p.
FO-DC550_Copy(Sec).book 35 ページ 2004年3月25日 木曜日 午後3時44分 CONVENIENT COPY FUNCTIONS 3 Press the [ ] key ( ) to move " " to the "ON" position and then press the [ENTER] key. 4 Press the [ ] key ( ) or [ ] key ( ) to select the margin position and then press the [ENTER] key. MARGIN SHIFT ON OFF MARGIN SHIFT LONG EDGE Select "LONG EDGE" or "SHORT EDGE". For the margin position, see the previous page. 5 Select the number of copies and any other settings, and then press the [START] key ( ).
FO-DC550_Copy(Sec).book 5 36 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 5 SET UP THE SOFTWARE This chapter explains how to install and configure the software that is required for the printer and scanner functions of the machine. The procedure for viewing the Online Manual is also explained. Note • The screen images in this manual are mainly for Windows XP. With other versions of Windows, some screen images may be different from those in this manual.
FO-DC550_Copy(Sec).book 37 ページ 2004年3月25日 木曜日 午後3時44分 BEFORE INSTALLATION Hardware and software requirements Check the following hardware and software requirements in order to install the software. Computer type IBM PC/AT or compatible computer equipped with a USB2.0*1/1.1*2 or bi-directional parallel interface (IEEE1284) Operating system*3 *4 Windows 95, Windows 98, Windows Me, Windows NT Workstation 4.
FO-DC550_Copy(Sec).book 38 ページ 2004年3月25日 木曜日 午後3時44分 INSTALLING THE SOFTWARE Note • If you need to use a different connection method after installing the software based on a USB or parallel connection, you must first uninstall the software (See "Removing the software" on page 78) and then install it using the new connection method. • In the following explanations it is assumed that the mouse is configured for right hand operation. • The scanner feature only works when using a USB cable.
FO-DC550_Copy(Sec).book 39 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 5 The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the software license, and then click the "Yes" button. 6 Read the "Readme First" in the "Welcome" window and then click the "Next" button. 7 Click the "Standard" button. "Integrated Installer is preparing..." will appear and then installation of the MFP driver, Button Manager, and Sharpdesk will begin automatically.
FO-DC550_Copy(Sec).book 40 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 10 Follow the instructions in the plug and play window to install the MFP driver. Follow the on-screen instructions. If you are running Windows 2000/XP and a warning message appears Caution regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes". Note A "USB 2.0 Composite Device" installation window may appear prior to this procedure.
FO-DC550_Copy(Sec).book 41 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 5 The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the software license, and then click the "Yes" button. 6 Read the "Readme First" in the "Welcome" window and then click the "Next" button. 7 Click the "Custom" button. 8 Click the "MFP Driver" button. 5 To view detailed information on the software, click the "Display Readme" button. 9 The "Welcome" window will appear.
FO-DC550_Copy(Sec).book 42 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 10 When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button. If you are using the machine as a shared printer on a network, select "Connected via the network". For more information on this setting, see "Using the machine as a shared printer" (p.48). Follow the on-screen instructions.
FO-DC550_Copy(Sec).book 43 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE If the following screen appears during installation of Sharpdesk, click Caution the "Skip" button or the "Continue" button as appropriate to continue the Sharpdesk installation. If "Skip" is selected, the Sharpdesk installation will continue without installing Sharpdesk imaging. If "Continue" is selected, Sharpdesk Imaging will be installed.
FO-DC550_Copy(Sec).book 44 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE If you are running Windows XP and a warning message appears Caution regarding the Windows logo test or digital signature, be sure to click "Continue Anyway". Note A "USB 2.0 Composite Device" installation window may appear prior to this procedure. In this case, follow the instructions in the window to install the USB 2.0 Composite Device. This completes the installation of the software.
!05-Setting up.fm 45 ページ 2004年3月30日 火曜日 午後4時29分 SET UP THE SOFTWARE 5 When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button. 6 When the interface selection screen appears, select "USB" and click the "Next" button. If you are using the machine as a shared printer on a network, select "Connected via the network". For more information on this setting, see "Using the machine as a shared printer" (p.48). Follow the on-screen instructions.
!05-Setting up.fm 46 ページ 2004年3月30日 火曜日 午後4時29分 SET UP THE SOFTWARE 9 Follow the instructions in the plug and play window to install the MFP driver. Follow the on-screen instructions. If you are running Windows 2000 and a warning message appears Caution regarding the Windows logo test or digital signature, be sure to click "Yes". Note A "USB 2.0 Composite Device" installation window may appear prior to this procedure. In this case, follow the instructions in the window to install the USB 2.
FO-DC550_Copy(Sec).book 47 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 5 When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button. If you are using the machine as a shared printer on a network, select "Connected via the network". For more information on this setting, see "Using the machine as a shared printer" (p.48). 6 When the interface selection screen appears, select "Parallel" and click the "Next" button.
FO-DC550_Copy(Sec).book 48 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 8 When the model selection window appears, select model name of your machine and click the "Next" button. Follow the on-screen instructions. If you are running Windows 2000 and a warning message appears Caution regarding the Windows logo test or digital signature, be sure to click "Yes". 9 You will return to the window of step 3. If you wish to install Sharpdesk, click the "Utility Software" button.
FO-DC550_Copy(Sec).book 49 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 2 Click the "MFP Driver" button. To view detailed information on the software, click the "Display Readme" button. 3 The "Welcome" window will appear. Click the "Next" button. 4 When you are asked how the printer is connected, select "Connected via the network" and click the "Next" button. 5 5 When you are asked to select the printer port to be used, click the "Add Network Port" button.
FO-DC550_Copy(Sec).book 50 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 6 Select the network printer that is shared and click the "OK" button. Ask your network administrator for the server name and printer name of the machine on the network. 7 In the printer port selection window, verify the network printer that is shared and whether the machine is to be used as the default printer, make the selections and click the "Next" button.
FO-DC550_Copy(Sec).book 51 ページ 2004年3月25日 木曜日 午後3時44分 SETTING UP BUTTON MANAGER Button Manager is a software program that works with the scanner driver to enable scanning from the machine. To scan using the machine, Button Manager must be linked with the scan menu on the machine. Follow the steps below to link Button Manager to scanner events. Windows XP 1 Click the "start" button, click "Control Panel", click "Printers and Other Hardware", and then click "Scanners and Cameras".
FO-DC550_Copy(Sec).book 52 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 5 Select "Start this program" and select "Sharp Button Manager F" from the pull-down menu. 6 Click the "Apply" button. 7 Repeat Steps 4 through 6 to link Button Manager to "SC2:" through "SC6:". Select "SC2:" from the "Select an event" pull-down menu. Select "Start this program", select "Sharp Button Manager F" from the pull-down menu, and then click the "Apply" button. Do the same for each ScanMenu through "SC6:".
FO-DC550_Copy(Sec).book 53 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE Windows 98/Me/2000 1 Click the "Start" button, select "Settings", and then click "Control Panel". 2 Double-click the "Scanners and Cameras" icon. Note 3 If the "Scanners and Cameras" icon does not appear in Windows Me, click "view all Control Panel options". Select "SHARP FO-DC550" and click the "Properties" button. In Windows Me, right click "SHARP FO-DC550" and click "Properties" in the pop-up menu.
FO-DC550_Copy(Sec).book 54 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE 6 Select "Sharp Button Manager F" in "Send to this application". Note If other applications are shown, deselect the checkboxes for the other applications and leave only the Button Manager checkbox selected. 7 Click the "Apply" button. 8 Repeat Steps 5 through 7 to link Button Manager to "SC2:" through "SC6:". Select "SC2:" from the "Scanner events" pull-down menu.
FO-DC550_Copy(Sec).book 55 ページ 2004年3月25日 木曜日 午後3時44分 CONNECTING THE MACHINE TO YOUR COMPUTER Connecting a USB cable Follow the procedure below to connect the machine to your computer. A USB cable for connecting the machine to your computer is not included with the machine. Please purchase the appropriate cable for your computer.
FO-DC550_Copy(Sec).book 56 ページ 2004年3月25日 木曜日 午後3時44分 SET UP THE SOFTWARE Connecting a parallel cable 56 1 Obtain an IEEE1284 shielded parallel interface cable. 2 Insert the cable into the parallel interface connector located on the rear of the unit, and fasten with clasps. 3 Insert the other end of the cable into the interface connector of your computer.
FO-DC550_Copy(Sec).book 6 57 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 6 PRINTER/SCANNER FUNCTIONS The machine includes a USB connector and a parallel connector as standard equipment. When the USB connector is used, the printer and scanner functions can be used. When the parallel connector is used, the printer function can be used. The machine has the following features: • High-speed data transfer (when connected to a USB 2.
FO-DC550_Copy(Sec).book 58 ページ 2004年3月25日 木曜日 午後3時44分 USING THE PRINTER MODE The procedure for loading paper for printing is the same as for loading copy paper. See "LOADING PAPER" (p.14). Note • Print jobs received while the machine is copying will be stored in memory. When the copy job is finished, the print jobs will begin printing. • Printing is not possible when the front or side cover is opened for machine maintenance, or when a misfeed occurs or the machine runs out of paper or toner.
FO-DC550_Copy(Sec).book 59 ページ 2004年3月25日 木曜日 午後3時44分 USING THE SCANNER MODE The procedure for placing the original is the same as for copying. See "NORMAL COPYING" (p.20). Note Scanner mode cannot be used at the following times: • A misfeed has occurred (paper misfeed or original misfeed in the RSPF). • The user programs are being used. • The tray paper size is being set. • The machine is being used in copy mode. • The front cover or side cover is open.
FO-DC550_Copy(Sec).book 60 ページ 2004年3月25日 木曜日 午後3時44分 PRINTER/SCANNER FUNCTIONS Button Manager scan menu For information on Button Manager settings, see the Button Manager help file. The names in the Button Manager menu ("xxxx" in "SC1:xxxx", etc.) can be changed. See the online manual. SCANNING FROM YOUR COMPUTER The machine supports the TWAIN standard, making it possible to scan from TWAINcompliant applications.
!06-printer.fm 61 ページ 2004年3月26日 金曜日 午前8時48分 HOW TO USE THE ONLINE MANUAL The online manual provides detailed instructions for operating the unit as a printer and scanner. It also provides methods for dealing with printing or scanner problems. To access the online manual, your computer must have Acrobat Reader 5.0 or later. If this is not installed, refer to "Installing Acrobat Reader" (below). 1 Turn on your computer. 2 Insert the supplied CD-ROM into your CD-ROM drive.
FO-DC550_Copy(Sec).book 7 62 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 7 USER SETTINGS The user settings allow you to customize machine settings to better meet your needs. USER PROGRAMS The user settings consist of the following items. To change a user program setting, see "SELECTING A SETTING FOR A USER PROGRAM" (p.67). Note For the user programs in fax mode, see the Operation Manual (for facsimile).
FO-DC550_Copy(Sec).book 63 ページ 2004年3月25日 木曜日 午後3時44分 USER SETTINGS Program number 4 5 6 7 Program name AUTO SHUT-OFF TIME Setting codes (factory default setting appears in bold) 1: 5 MIN. 2: 30 MIN. 3: 60 MIN. 4: 120 MIN. 5: 240 MIN.
FO-DC550_Copy(Sec).book 64 ページ 2004年3月25日 木曜日 午後3時44分 USER SETTINGS Program number 8 9 ROTATE ORIG. IMAGE AE/TEXT RESOLUTION Setting codes (factory default setting appears in bold) Explanation 1: ON 2: OFF • When two-sided copying is performed, this function rotates the image on the back of the original. This is convenient when binding the copies at the top (tablet binding).
FO-DC550_Copy(Sec).book 65 ページ 2004年3月25日 木曜日 午後3時44分 USER SETTINGS Program number Program name Setting codes (factory default setting appears in bold) Explanation • Use this setting to select how long a key must be pressed for the input to be accepted. By selecting a longer time, you can prevent settings from being changed by the accidental pressing of a key. 14 KEY PRESS TIME 1: NORMAL 2: 0.5 SEC. 3: 1.0 SEC. 4: 1.5 SEC. 5: 2.0 SEC.
FO-DC550_Copy(Sec).book 66 ページ 2004年3月25日 木曜日 午後3時44分 USER SETTINGS Print mode Program number 1 2 3 Program name Setting codes (factory default setting appears in bold) Explanation • When this function is enabled, printing in printer mode will automatically continue using a different size of paper if the specified size of paper runs out in all trays. This feature does not function in copy mode. FORCED OUTPUT 1: ON 2: OFF USB 2.0 MODE SWITCH*1 • This sets the USB 2.0 data transfer speed.
FO-DC550_Copy(Sec).book 67 ページ 2004年3月25日 木曜日 午後3時44分 SELECTING A SETTING FOR A USER PROGRAM 1 Press the [MENU] key and then press the [ENTER] key. MAIN MENU 1:USER PROGRAM In printer mode, the user programs are accessed by simply pressing the [MENU] key. 2 Press the [ ] key ( ) or [ ] key ( ) to select the item that you wish to configure in the USER PROGRAM items, and then press the [ENTER] key. USER PROGRAM 2:PREHEAT MODE • See "USER PROGRAM" (p.62 to p.
FO-DC550_Copy(Sec).book 68 ページ 2004年3月25日 木曜日 午後3時44分 USER SETTINGS Audible signals (key entry beep, invalid key beep, base setting beep) The machine sounds three different types of beep signals: a key entry beep that sounds when a valid key is pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds when a setting is the same as the base setting (base settings are explained below). The base setting beep is initially disabled.
FO-DC550_Copy(Sec).book 8 69 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 8 TROUBLESHOOTING AND MAINTENANCE Problems related to general use of the machine, the copy function, and software setup are explained here. Be sure to check the problem carefully before calling for service, as many problems can be solved by the user. If you are unable to solve the problem, turn off the main switch, unplug the power cord from the outlet, and contact your SHARP authorized dealer.
FO-DC550_Copy(Sec).book 70 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE Indication Lamp indicator Display INSTALL A TD CARTRIDGE. Blinks REPLACE THE DRUM CARTRIDGE. Error TD CARTRIDGE indicator IS NEAR EMPTY. Steadily A DRUM lit CARTRIDGE WILL BE NEEDED SOON. MEMORY FULL, PRESS START TO RESUME. NO 2-SIDED COPY FROM BYPASS TRAY. NO 2IN1 COPY FROM BYPASS TRAY. NO 2IN1 COPY WITH MARGIN SHIFT. COPY RATIO CAN NOT BE CHANGED IN 2IN1. THIS MENU IS NOT SELECTABLE WITH DATA.
FO-DC550_Copy(Sec).book 71 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING THE MACHINE The following problems are related to the general operation of the machine and copying. Problem Cause and solution Page The machine is not plugged into a power outlet. → Plug the machine into a grounded outlet. - Power switch OFF. → Turn the power switch ON. The machine does not operate. Copies are too dark or too light. Blank copies. 12 The power save indicator is blinking.
FO-DC550_Copy(Sec).book 72 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution The original was not placed in the correct position. → Place the original correctly. Part of the image is cut off or there is too much blank space. Wrinkles appear in the paper or the image disappears in places. Copies are smudged or dirty. 72 Page 20, 21 An appropriate ratio was not used for the size of the original and the size of the paper.
FO-DC550_Copy(Sec).book 73 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution Page Misfeed occur. → To remove the misfeed, see "MISFEED REMOVAL". 79 The paper is outside of the specified size and weight range. → Use copy paper within the specified range. 14 Paper curled or damp. → Do not use curled or crimped paper. Replace with dry copy paper.
!08-troubleshooting.fm 74 ページ 2004年3月26日 金曜日 午前8時47分 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution Copying or printing is performed. → Set the paper size after copying or printing is complete. Paper size for a paper tray cannot be set. A copy job stops before it is finished. The power save indicator is lit. Error indicator ( lit or blinking. ) is Lighting fixture flickers. 74 Page - The machine has stopped temporarily due to running out of paper or a misfeed.
FO-DC550_Copy(Sec).book 75 ページ 2004年3月25日 木曜日 午後3時44分 PROBLEMS DURING SETUP OF THE SOFTWARE If the software does not install correctly, check the following items on your computer. To remove the software, see "Removing the software" (p.78). MFP driver cannot be installed (Windows 2000/XP) If the MFP driver cannot be installed in Windows 2000/XP, follow these steps to check your computer's settings. 1 Click the "start" button and then click "Control Panel".
FO-DC550_Copy(Sec).book 76 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE Plug and play screen does not appear (USB only) If the Plug and Play screen does not appear after you connect the machine to your computer with a USB cable and turn on the machine, follow the steps below to verify that the USB port is available. 1 Click the "start" button, click "Control Panel", and then click "Performance and Maintenance".
FO-DC550_Copy(Sec).book 77 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE The MFP driver cannot be correctly installed by Plug and Play (Windows 2000/XP) (USB only) In Windows 2000/XP, if the MFP driver cannot be correctly installed by Plug and Play (for example, Plug and Play takes place without copying the required files for the MFP driver installation), follow these steps to remove unneeded devices and then install the MFP driver as explained in "SET UP THE SOFTWARE" (p.36).
FO-DC550_Copy(Sec).book 78 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE 4 Select "FILE:" in the "Print to the following port" list box, and click the "OK" button. 5 Click the "SHARP FO-DC550" printer driver icon and select "Properties" from the "File" menu. 6 Click the "Ports" tab. In Windows 95/98/Me, click the "Details" tab. 7 Select "LPT1" in the "Print to the following port" list box, and click the "OK" button.
!08-troubleshooting.fm 79 ページ 2004年3月30日 火曜日 午後4時30分 MISFEED REMOVAL When a misfeed occurs, the error indicator blinks, "CLEAR PAPER JAM" appears in the display, and the machine stops copying or printing. If a misfeed occurs when using the RSPF, "RETURN X ORIGINAL(S) START TO RESUME" will appear in the display. ("X" indicates the number of pages to be returned.) This indicates the number of the originals that must be returned to the document feeder tray after a misfeed.
FO-DC550_Copy(Sec).book 80 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE A: Misfeed in the paper feed area 1 Gently remove the misfed paper from the paper feed area as shown in the illustration. If the error indicator blinks and the misfed paper is not visible in the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to "B: Misfeed in the fusing area". The fusing unit is hot.
FO-DC550_Copy(Sec).book 81 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE 2 Gently remove the misfed paper from under the fusing unit as shown in the illustration. If the paper cannot be removed, proceed to "C: Misfeed in the transport area". The fusing unit is hot. Do not touch the fusing unit when Warning removing misfed paper. Doing so may cause a burn or other injury. Caution 3 • Do not touch the surface (green portion) of the drum cartridge when removing the misfed paper.
FO-DC550_Copy(Sec).book 82 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE 4 Raise the fusing unit release lever, close the front cover and then close the side cover by pressing the round projections near the side cover open button. The error indicator will go out and the ready indicator will light up. When closing the covers, be sure to close the front cover securely and Caution then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.
!08-troubleshooting.fm 83 ページ 2004年3月26日 金曜日 午前8時47分 TROUBLESHOOTING AND MAINTENANCE (C) If the original does not move easily into the exit area, remove it in the direction of the arrow while rotating the roller. Note Open and close the RSPF to clear the error indicator. "RETURN X ORIGINAL(S) START TO RESUME" will appear in the display. Return the indicated number of pages to the document feeder tray. Press the [START] key ( ) to resume copying.
!08-troubleshooting.fm 84 ページ 2004年3月30日 火曜日 午後4時31分 TD CARTRIDGE REPLACEMENT When toner is low, the error indicator will light up and "TD CARTRIDGE IS NEAR EMPTY" will appear in the display. For information on purchasing a new TD cartridge, see "ABOUT SUPPLIES" (p.91). If copying is continued while the indicator is lit, copies will gradually become lighter until the toner runs out.
FO-DC550_Copy(Sec).book 85 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE 3 Gently pull the TD cartridge out while pressing the lock release button. Note 4 Lock release button • After removing the TD cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge. • Dispose of the old TD cartridge in accordance with local regulations.
FO-DC550_Copy(Sec).book 86 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE 6 Close the front cover and then the side cover by pressing the round projections near the side cover open button. The error indicator will go out and the ready indicator will light up. 7 When closing the covers, be sure to close the front cover securely and Caution then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.
!08-troubleshooting.fm 87 ページ 2004年3月30日 火曜日 午後4時33分 DRUM CARTRIDGE REPLACEMENT The useful life of the drum cartridge is approximately 18,000 copies*. When the internal counter reaches approximately 17,000 copies, the error indicator will light up and "A DRUM CARTRIDGE WILL BE NEEDED SOON" will appear in the display. For more information on purchasing a drum cartridge, see "ABOUT SUPPLIES" (p.91).
FO-DC550_Copy(Sec).book 88 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE 5 Close the front cover and then the side cover by pressing the round projections near the side cover open button. The drum replacement required error indicator will go out and the ready indicator will light up. Note When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.
!08-troubleshooting.fm 89 ページ 2004年3月25日 木曜日 午後5時1分 CLEANING THE MACHINE Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to clean the machine on a regular basis. Do not spray flammable cleaner gas. Gas from the spray may Warning come in contact with the internal electrical components or hightemperature parts of the fusing unit, creating a risk of fire or electrical shock.
FO-DC550_Copy(Sec).book 90 ページ 2004年3月25日 木曜日 午後3時44分 TROUBLESHOOTING AND MAINTENANCE Transfer charger If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. 1 Turn the power switch off. (p.13) 2 Ensure that the bypass tray is open and then open the side cover while pressing the side cover open button. (p.79) 3 Take the charger cleaner out by holding the tab.
!08-troubleshooting.fm 91 ページ 2004年3月26日 金曜日 午前8時46分 TROUBLESHOOTING AND MAINTENANCE TD cartridge and drum cartridge 1 Remove the TD cartridge and drum cartridge as explained in "TD CARTRIDGE REPLACEMENT" (p.84) and "DRUM CARTRIDGE REPLACEMENT" (p.87). 2 Wipe the parts of the TD cartridge and drum cartridge shown below with a clean cloth. Wipe only the parts that are indicated in the illustration. Note 3 • Do not touch the surface of the drum (green portion).
FO-DC550_Copy(Sec).book 9 92 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 9 OPTIONAL EQUIPMENT SYSTEM CONFIGURATION A number of options are available for the unit which allow you to configure a system to meet your particular needs. The options include the following. Note Be sure to use only genuine SHARP parts and supplies. Network Expansion Kit (AR-NB2 N) 250-sheet paper feed unit (AR-D16) NETWORK EXPANSION KIT (AR-NB2 N) This allows the machine to be used as a network printer/network scanner.
FO-DC550_Copy(Sec).book 93 ページ 2004年3月25日 木曜日 午後3時44分 OPTIONAL EQUIPMENT Using the AR-D16 with the printer function To use the AR-D16 with the printer function, follow these steps to adjust the settings in the printer driver. Note The printer driver cannot be set for use with the AR-D16 when opened from the application. 1 Click the "start" button. 2 Click "Control Panel", select "Printer and Other Hardware", and then click "Printer and Faxes". In Windows 95/98/Me/NT 4.
FO-DC550_Copy(Sec).book 10 94 ページ 2004年3月25日 木曜日 午後3時44分 Chapter 10 APPENDIX SPECIFICATIONS Model FO-DC550 Type Digital Multifunctional System, Desktop Photoconductive type OPC drum Document glass type Fixed Copy/printing system Dry, electrostatic transfer Originals Sheets, bound documents Originals size Max. 8-1/2" x 14" Copy size Max. 8-1/2" x 14" Min. 3-1/2" x 5-1/2" Image loss: Max. 5/32" (4 mm) (leading and trailing edges) Max. 11/64" (4.5 mm) (along other edges in total) Max.
FO-DC550_Copy(Sec).book 95 ページ 2004年3月25日 木曜日 午後3時44分 APPENDIX Fusing system Heat rollers Developer system Magnetic brush development Light source Tri-color CCD light source (CCD: 3 components; R, G, and B) Resolution Scan: 600 x 300 dpi Output: 600 x 600 dpi (AUTO/TEXT mode) Scan: 600 x 600 dpi Output: 600 x 600 dpi (PHOTO mode) Gradation Scanning: 256 Printing: 2 value Power supply AC 120V, 60 Hz, 8A Power consumption Max. 1.0 kW Overall dimensions (with bypass tray 20.4" (W) x 19.
FO-DC550_Copy(Sec).book 96 ページ 2004年3月25日 木曜日 午後3時44分 APPENDIX Printer Function 96 Print speed 16ppm Resolution 600 dpi Memory Approx. 10MB Emulation SPLC (Sharp Printer Language with Compression) Interface IEEE 1284-compliant bi-directional parallel interface USB 2.0 (Full-Speed/Hi-Speed compatible interface) Interface cables [USB cable] USB cable that supports USB 2.0. Please purchase a commercially available USB cable.
FO-DC550_Copy(Sec).book 97 ページ 2004年3月25日 木曜日 午後3時44分 APPENDIX Scanner Function Type Flatbed scanner Scanning method Document glass/RSPF Light source Tri-color CCD light source (CCD: 3 components; R, G, and B) Resolution Basic: 600 dpi x 1200 dpi Setting range: 50dpi - 9600dpi Original types Sheet media, books Effective scanning area 8.5" (216 mm) (Lengthwise) x 14" (356 mm) (Width) Scanning speed 2.88 msec/line Input Data 1 bit or 12 bit Output Data R.G.
FO-DC550_Copy(Sec).book 98 ページ 2004年3月25日 木曜日 午後3時44分 APPENDIX 250-sheet paper feed unit (AR-D16) Paper size 5-1/2" x 8-1/2" to 8-1/2" x 14" Paper weight 15 lbs. to 21 lbs. (56g/m2 to 80g/m2 ) Paper capacity One paper tray with capacity for 250 sheets of 21 lbs. bond paper Weight 6.6 lbs. (3kg) Dimensions 19.6" (W) x 15.6" (D) x 3.
FO-DC550_Copy(Sec).book 99 ページ 2004年3月25日 木曜日 午後3時44分 SOFTWARE LICENSE PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. 1. License. The application, demonstration, system and other software accompanying this License, whether on disk, in read only memory, or on any other media (the "Software") and related documentation are licensed to you by SHARP.
FO-DC550_Copy(Sec).book 100 ページ 2004年3月25日 木曜日 午後3時44分 6. Limited Warranty on Media. SHARP warrants the disks on which the Software is recorded to be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/or its Licensors and your exclusive remedy will be replacement of the disk which fails to meet the limited warranty provided by this Clause 6.
FO-DC550_Copy(Sec).book 101 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Page: 1/4 Date Rivised : Mar. 1. 2004 Date Issued : Sep. 1. 2003 MSDS No. F-01231 1. PRODUCT AND COMPANY IDENTIFICATION : FO-DC550 / FO-55ND (Black Toner) Product Name Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) U.S.A.
FO-DC550_Copy(Sec).book 102 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Page: 2/4 Date Rivised : Mar. 1. 2004 Date Issued : Sep. 1. 2003 MSDS No. F-01231 3. HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.
FO-DC550_Copy(Sec).book 103 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Page: 3/4 Date Rivised : Mar. 1. 2004 Date Issued : Sep. 1. 2003 MSDS No. F-01231 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Measures Ventilation : Not required under intended use.
FO-DC550_Copy(Sec).book 104 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Chronic Effect Page: 4/4 Date Rivised : Mar. 1. 2004 Date Issued : Sep. 1. 2003 MSDS No.
FO-DC550_Copy(Sec).book 105 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Page: 1/4 Date Rivised: Mar. 1. 2004 Date Issued: Sep. 1. 2003 MSDS No. F-31231 1. PRODUCT AND COMPANY IDENTIFICATION : FO-DC550 / FO-55ND (Black Developer) Product Name Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) U.S.A.
FO-DC550_Copy(Sec).book 106 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Page: 2/4 Date Rivised: Mar. 1. 2004 Date Issued: Sep. 1. 2003 MSDS No. F-31231 3. HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.
FO-DC550_Copy(Sec).book 107 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Page: 3/4 Date Rivised: Mar. 1. 2004 Date Issued: Sep. 1. 2003 MSDS No. F-31231 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Measures Ventilation : Not required under intended use.
FO-DC550_Copy(Sec).book 108 ページ 2004年3月25日 木曜日 午後3時44分 MATERIAL SAFETY DATA SHEET Chronic Effect Page: 4/4 Date Rivised: Mar. 1. 2004 Date Issued: Sep. 1. 2003 MSDS No.
!10-index.fm 109 ページ 2004年3月26日 金曜日 午前8時49分 INDEX Symbols 2 IN 1 copy ....................................... 31 250-sheet paper feed unit .......... 92, 98 [2-SIDED COPY] key ........... 10, 27, 28 [CLEAR] key ............... 10, 20, 21, 23, 29, 30, 58, 79 Connecting the machine to your computer - Parallel cable............................... 56 - USB cable ................................... 55 Convenient copy functions ............... 26 Conventions used in this manual and online manual ............
FO-DC550_Copy(Sec).book 110 ページ 2004年3月25日 午後3時44分 I O Initial settings.................................... 12 Installation environment and usable software ............................................ 37 Installing Acrobat Reader ................. 61 Installing the software - Custom installation ...................... 40 - Standard installation.................... 38 Interface cable .................................. 93 Introduction.........................................
FO-DC550_Copy(Sec).book 111 ページ 2004年3月25日 木曜日 午後3時44分 R T Ready indicator .......................... 11, 12 Reduction/enlargement/zoom .......... 25 Removing the software..................... 78 Reversing tray .............................. 9, 82 Roller rotating knob .......................... 81 RSPF .................................................. 9 RSPF indicator ................................. 10 TD cartridge................................... 9, 84 TD cartridge replacement.................
!10-index.fm 112 ページ 2004年3月29日 月曜日 午前8時53分 INDEX BY PURPOSE Preparations Connecting the computer Paper, loading - Bypass tray................................... 17 - Paper tray..................................... 15 Power, turn off ................................... 13 Power, turn on ................................... 12 Scan head locking switch, releasing ............................................ 83 Tray's paper size, setting................... 19 User program, setting ........................
FO-DC550_Copy(Sec).book 63 ページ 2004年3月25日 木曜日 午後3時44分 ♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠ For users in the USA This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FO-DC550 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163. www.sharpusa.