Service manual

FO-IS125N
2 – 7
[2] Diagnostics and service soft switch
1. Entering the diagnostic mode 2. Diagnostic items description
2.1. SOFT SWITCH MODE
In this mode, the soft switches are set and the soft switch list is printed.
2.1.1 Operation
Soft switch mode screen
2.1.2 Switch number selection and data setting
1. Enter three digits of a soft switch number to set the switch number.
Of a switch number of unexacting soft switch is entered, key error
buzzer sounds to reject the input.
2. Press [START] key moves the cursor to the data number 1 of the
former soft switch. If the switch number is the final, pressing
[START] key will exit the soft switch mode.
3. Data number selection
a) Pressing [>] or [#] key moves the cursor to the right. If the cursor
is on data number 8, pressing [>] or [#] key shifts the cursor to data
number 1 of the next switch number. If the switch number is the
final, pressing [>] or [#] key will exit the soft switch mode.
b) Pressing [<] or [ ] key moves the cursor to the left. If the cursor
is on data number 1, pressing [<] or [ ] key shifts the cursor to
data number 8 of the former switch number. If the switch number is
001, pressing [<] or [ ] key do not move the cursor.
c) Pressing [UP] or [4] key moves the cursor to the data number 1
of the next soft switch. If the switch number is 001, pressing [UP] or
[4] key shifts the cursor to data number 1.
d) Pressing [DOWN] or [6] key moves the cursor to the data num-
ber 1 of the former soft switch. If the switch number is the final,
pressing [down] or [6] key will exit the soft switch mode.
FUNCTION
9 8
START
SOFT SWITCH MODE
START
ROM & RAM CHECK
START
AGING MODE
START
PANEL KEY TEST
START
CHECK PATTERN
START
SIGNAL SEND MODE
START
MEMORY CLEAR
START
SHADING MODE
START
AUTO FEEDER MODE
START
FLASH MEM. CHECK
START
MEMORY SET MODE
START
CIS ADJUST
START
SHARP CHART MODE
ROM:TF78
FUNCTION
9 8
Press
, and
the
following
display will appear
ROM:TF78
Select the desired item with the
key
and the key or select
with the rapid key.
Enter the mode with the
START key.
(Diag
• specifications)
: ROM version
START
ASF AGING
UP DOWN
alternately.
UP
DOWN
START
PASSCODE LIST
START
LIFE SET MODE
START
LIFE CLR MODE
7
Then press the START key.
COUNTRY NAMEDIAG MODE
START
7
START
SIGNAL SEND MODE2
START
5% CHART
SOFT SWITCH MODE
SW123=00100100
Switch No.
12345678:DataNo.
SW =
SW1 =
[1] key
SW12 =
[2] key
SW123=00100100
[3] key
Cursor position
SW124=00000000
[START] key
SW125=00000000
SW123=01100000
[START] key
SW123=01100000
SW123=01100000
[>] or [#] key
SW124=00000000
With the cursor on data 8
[>] or [#] key
SW124=00000000
[>] or [#] key
SW124=00000000
SW124=00000000
[<] or [ ] key
SW123=01100000
With the cursor on data 1
[<] or [ ] key
SW123=01100000
[<] or [ ] key
SW124=00000000
[UP] or [4] key
SW123=01100000
SW125=00000000
[UP] or [4] key
SW124=00000000
[DOWN] or [6] key
SW125=00000000
SW123=01100000
[DOWN] or [6] key