R PURIFICADOR DE AIRE MANUAL DE USO Free standing type Tisch- / Wandgerät Type de table / installation murale De sobremesa / instalación en la pared Tipo da scrivania / parete Tafelmodel / wandmodel *Plasmacluster is a trademark of Sharp Corporation.
ENGLISH Please read before operating your new Air Purifier The air purifier draws in room air from its air intake, lets the air pass through a Active Carbon Filter (deodorization filter) and a HEPA Filter (dust collection filter) inside of the unit, then discharges the air from its air outlet. The air purifier unit repeats this process by moving its internal fan. As air passes through, a new HEPA Filter can remove 99.97% of dust particles, of as small as 0.3 microns.
ION SHOWER New ION SHOWER Operation Mode releases the concentrated Plasmacluster Ions, and effectively removes the pollen and mold, and also controls the activity of airborne virus, mold, and allergen. Plasmacluster Ion Control Your new air purifier will control the ratio of negative ions and positive ions depending on the condition of the room. • Clean Mode Approximately the same numbers of positive and negative ions are discharged.
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should be followed, including the following: WARNING - To reduce the risk of electrical shock, fire or injury to persons: • Read all instructions before using the air purifier. • Use only a 220-240 volt outlet. • Do not use the air purifier if the power cord or plug is damaged or the connection to the wall outlet is loosened. • Periodically remove dust from the power plug.
IMPORTANT SAFETY INSTRUCTIONS CAUTIONS CONCERNING OPERATION INSTALLATION GUIDELINES • During the operation of the product, please place the unit at least 2m away from equipments which involve electric wave such as televisions, radios or wave clocks, in case electrical interference occurs to such equipment. • Avoid a location where the sensor is exposed to direct wind. The unit may not operate properly. • Avoid locations where curtains, etc., come into contact with the intake or air outlet. Curtains, etc.
PART NAMES MAIN UNIT DISPLAY POWER ON/OFF Button Plasmacluster Ion Mode Selection Button Mode Selection Button Fan Speed Indicator Lights Pollen Mode Indicator Light ION SHOWER Indicator Light AUTO Operation Indicator Light Odour Senser Plasmacluster Ion Mode Indicator Lights ILLUSTRATIVE DIAGRAM Odour Sensor Main Unit HEPA Filter (blue/white) Washable Active Carbon Filter (black) Filter Support Front Panel E-4
Plasmacluster Indicator Lights (Please refer page E-9) Blue light • When the Plasmacluster ion operation is in Clean Mode, or in AUTO Plasmacluster Ion Mode and the air in the room is impure, the light will be activated and the unit will operate in Clean Mode. • When the Plasmacluster ion operation is in ION SHOWER Mode, the light will repeat its colour cycles between light and shade.
PREPARATION Be sure to remove the power plug from the wall outlet. FILTER INSTALLATION To maintain the quality of the filters, they are installed in the main unit and packed in plastic bags. Be sure to remove the filters from the plastic bags before using the unit. 11 Front Panel Remove the filters 1 Remove the Front Panel. Pull the bottom of the Front Panel. 2 Remove the Filter Support. Pinch the two tabs and lift to remove. Up side Tabs Tabs the Active Carbon 3 Remove Filter and HEPA Filter.
Install the filters Tab the HEPA Filter 1 Place within the main unit with HEPA Filter the tabs facing up. Do not install the filter backwards or the unit will not operate properly. the Active Carbon 2 Place Filter on top of the HEPA Tabs Tabs Filter. Make sure that the tab of the HEPA Filter remains visible. ENGLISH 22 Active Carbon Filter the bottom side tabs of the Filter Support 3 Insert into the associated holes of the main unit. Next push the upside tabs into the main unit.
OPERATION MAIN UNIT OPERATION Plasmacluster Indicator Lights Plasmacluster ION Mode Indicator Lights Power ON/OFF Button • Used to start operation (short beep) and stop operation (long beep) • Plasmacluster Indicator Light and Fan Speed Indicator Light turn on/off. • Unless unplug the power cord, the operation starts in the previous mode the unit was operated in. MODE Selection Button • The operation mode can be switched.
Mode Selection Button Plasmacluster Ion Mode Selection Button POWER ON/OFF Button CLEAN - SIGN Light Plasmacluster Ion Mode Selection Button AUTO The unit will switch between Clean Mode and the Ion Control Mode* automatically depending on the amount of impurities in the air as detected by the odour sensor. Clean Mode operate for 10 minutes when the Auto function is selected. CLEAN The unit will constantly operate in the Clean Mode, in which the same numbers of positive and negative ions are discharged.
CARE AND MAINTENANCE To maintain optimum performance of this air purifier, please clean the unit including the sensor and filters periodically. When cleaning the unit, be sure to unplug the power cord, and never handle the plug with wet hands. Electrical shock and/or bodily injury may occur as a result. MAIN UNIT Care Cycle 1 month To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to remain, they may become hard to clean.
WASHABLE ACTIVE CARBON FILTER CARE WASHABLE ACTIVE CARBON FILTER CARE HAND WASH ONLY! DO NOT TUMBLE DRY! Care Cycle We recommend to the active carbon filter every six months. Clean the filter as offen as necessary when odour persists. the filter outdoors if possible in a large container with 5 Dry 1 Fill a well ventilated area. lukewarm water, add a mild kitchen detergent and stir. the filter to soak ap2 Allow proximately 10 minutes .
CARE AND MAINTENANCE FILTER REPLACEMENT GUIDELINES Depending on the usage environment, air outlet odour may become strong after several months. If dust or odour cannot be removed easily, replace the filters.
TROUBLESHOOTING Before calling for repair, please review the list below, since the problem may not be a unit malfunction. REMEDY (not a malfunction) Odours and smoke are not removed. • Clean or replace the filters if they appear to be heavily soiled. (Refer to E-11E-12) The CLEAN-SIGN Light lights green even when the air is impure. • The air could be impure at the time the unit was plugged in. (Refer to E-5) Pull out the plug from the electrical outlet, and insert the plug one minute later.
SPECIFICATIONS Fan Speed Operation Model Power supply Fan Speed Adjustment Rated Power Air Fiow Volume Applicable Floor Surface Cord Length Dimensions Weight FU-S25E 220-240V 50/60Hz MAX 26 W 150m3/hour MED 7.5W 60m3/hour SILENT 4.1 W 24m3/hour ~19m2*1 2.0m 410mm(W)x158mm(D)x430mm(H) 4.8kg *1 • The applicable floor surface area is appropriate for operating the unit at maximum fan speed.
A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! *) Please contact your local authority for further details. If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand according to local requirements.
SERVICE PROCEDURE / SERVICE VORGEHENSWEISE SERVICE PROCEDURE - ONLY EFFECTIVE IN GERMANY Dear SHARP customer, SHARP machines are proprietary articles which are produced with precision and care according to most modern production methods. In case of proper handling and with considering of the instruction book, this machine will serve you well for a long time. Of course, a defect cannot be ruled out.
SHARP CORPORATION OSAKA, JAPAN Printed in China TINS-A190KKRZ 05L−