Operation Manual
Table Of Contents
74
Data Communication
SH-08E_E_09.fm
[74/75]
1
In the Bluetooth screen, select the Bluetooth
device to disconnect/ [OK]
Set after setting the Bluetooth function to [ON].
1
In the Bluetooth screen, [z]
2
Select an item
Rename tablet: Change the tablet’s name.
Visibility timeout: Set how long the tablet’s information will be
displayed on the other party’s Bluetooth device.
aptX: Set whether to use aptX
®
.
Handsfree setting: Set whether to always have voices
emitted from the connected Bluetooth compatible hands-free
device during a voice call.
Disable BT Smart settings: Enable/Disable the BT Smart
settings.
Show received files: Display the history of data received via
Bluetooth connection.
Example: Still picture
1
In the home screen, [R]/[SH tool]/
[Recommendation]/[Contents manager]/
[Photo]
2
Touch and hold a still picture/[Share]/
[Bluetooth]
: Set the receiver’s Bluetooth device to receive data.
3
Select a Bluetooth device to connect to
1
Data is sent from the sender’s Bluetooth device
2
Drag the status bar down/select the incoming
notification/[Accept]
3
Drag the status bar down/select the received
data
You can make a Bluetooth Smart device respond to the tablet
operations or notify you of incoming calls or new mails by
operating the tablet if you connect the tablet to the Bluetooth
Smart device.
If you have connected the tablet to a Bluetooth Smart device, you
can make the Bluetooth Smart device ring or vibrate by operating
the tablet.
1
In the Bluetooth screen, [B] of a connected
Bluetooth Smart device/[Notify this device]
2
Select a notification method
You can make settings for operations available when the tablet is
connected to a Bluetooth Smart device.
1
In the Bluetooth screen, [B] of a connected
Bluetooth Smart device/[Advanced settings]
2
Select an item
Incoming call notification: Set whether to notify you through
the Bluetooth Smart device when receiving a call.
Mail reception notification: Set whether to notify you through
the Bluetooth Smart device when receiving a mail.
Alarm notification: Set whether to notify you through the
Bluetooth Smart device when an alarm rings.
Schedule notification: Set whether to notify you of schedule
notifications from the calendar through the Bluetooth Smart
device.
Time change notification: Set whether to synchronize clocks
between the Bluetooth Smart device and the tablet.
Link loss notification: Set how to notify you when the
Bluetooth connection is temporarily disabled.
NFC stands for Near Field Communication and is a near field
wireless communication system which conforms to the
international standards set by ISO (International Organization
for Standardization). By using the reader/writer function (R/W)
or Peer to Peer function (P2P), you can use “Kazashite-Link
compatible services” which enable you to access information
by holding the a mark of the tablet over home electric
appliances, smart posters, etc. on the tablet.
1
In the home screen, [R]/[Settings]/
[More...]/[NFC settings]
2
Select an item
Reader/Writer, P2P: Set whether to use the Reader/Writer,
P2P function.
Android beam: Perform data communication using Android
beam.
･ For details on Android beam nP. 74
You can send and receive data to and from devices which
support Reader/Writer, P2P function.
Enable [Reader/Writer, P2P] and set Android beam to [ON] in
advance (nP. 74).
Do not move the tablet until sending and receiving of data are
completed.
Disabling connection of Bluetooth device
Setting Bluetooth
[aptX]
When you enable [aptX], sounds may not be emitted depending
on the Bluetooth device. In this case, disable [aptX].
Sending and receiving by Bluetooth
Sending data
Receiving data
Note that if you select [Delete all before registration] when
receiving all data, all data registered to the target function are
deleted.
Some data cannot be received all.
When available space in the save destination becomes
insufficient while receiving data, the data being received to that
point are saved and receiving ends.
Bluetooth Smart device connection
Notifying this device
This is available only on Bluetooth Smart devices supporting
FMP (Find Me Profile).
Advanced settings
NFC communication
NFC settings
Android beam
SH-08E_E.book 74 ページ ２０１３年６月２８日 金曜日 午後３時７分