Draft S1 INSTRUCTION MANUAL ’ 16.
Package Contents Package Contents Package Contents Handset (S1) ・Battery is built into handset. ・Handset back cover is not removable.
Charging Handset Battery is built into handset. Internal Battery About Charging AC Charger Charging by PC Internal Battery A lithium-ion battery is built into handset; it is not removable. Recycling This product requires a lithium-ion battery. Lithium-ion batteries are recyclable. To recycle a used lithium-ion battery, take it to any shop displaying the recycling symbol.
Bulges of Internal Battery Depending on usage, bulges may appear near end of battery life; this does not affect safety. Internal Battery Replacement Internal Battery is a consumable item; may need to be replaced if operating time shortens noticeably. Internal Battery is not user replaceable; its replacement incurs fees and requires handset submission to a Y! Mobile Shop or other appropriate servicer. For details, contact a Y! Mobile Shop or Y! Mobile Customer Support, General Information.
About Charging Abroad Y! Mobile Corp. is not liable for problems resulting from charging handset abroad. AC Charger AC Charger is an optional accessory. Be sure to use SB-AC12-HDQC (SoftBank SELECTION Qualcomm® Quick ChargeTM 2.0 AC Adaptor for smartphones) or SB-AC13-HDMU (Micro USB, 1.0 A) specified by SoftBank Corp. For information on other peripheral devices, see SoftBank Website. The following explains how to charge handset using SB-AC12-HDQC (SoftBank SELECTION Qualcomm® Quick ChargeTM 2.
Insert Micro USB plug in correct orientation; otherwise, External Device Port may be damaged. Check contours and orientation of Micro USB plug, then insert it with tabs (○) facing down. Extend blades and plug AC Charger into AC outlet Charging starts and Charging/Notification Lamp illuminates. Charging/Notification Lamp goes out when charge is full.
Insert Micro USB plug in correct orientation; otherwise, External Device Port may be damaged. Check contours and orientation of Micro USB plug, then insert it with tabs (○) facing down. Insert USB plug of Micro USB Cable into PC USB port Charging starts and Charging/Notification Lamp illuminates. Charging/Notification Lamp goes out when charge is full.
Specifications Handset Materials Handset Handset specifications are as follows. Times in the table vary with location, status, settings, etc. Display employs precision technology; however, some pixels may remain on/off. Item Description Approx. ＊＊ mm x ＊＊＊ mm x ＊.＊ mm Dimensions (W x H x D) (without protruding parts) Weight Approx. ＊＊＊ g Maximum Output 3G: 0.25 W GSM (850 MHz, 900 MHz): 2 W GSM (1800 MHz, 1900 MHz): 1 W 4G: 0.2 W Internal Battery Capacity 2,400 mAh 3G: Approx.
Mbps in uplink 1 2 3 4 5 6 7 Average measured with handset fully charged, in strong signal conditions at rest. Average measured with handset fully charged, without calls or operations, in strong signal conditions at rest, and with data communication and Urgent News disabled. May vary with battery strength, ambient temperature, settings, etc.
Periphery of Back Surface PA resin + GF/UV top coating Power Key Aluminum/anodizing Volume Up/Down Key Aluminum/anodizing Receiver Screen SUS/electrophoretic coating Camera Window Tempered glass/AF coating USIM/Micro SD Card Slot Tray PC resin + TPU/UV top coating Card Slot Tray Gasket Silicone IMEI Tray PET Speaker Screen Nylon resin/water-repellent treatment External Device Port SUS/tin plating 9
Warranty & After-Sales Service Warranty After-Sales Service Warranty Handset purchase includes warranty. Check shop name and purchase date. Read warranty and keep in a safe place. Warranty period is given in warranty. Cautions Damages Y! Mobile Corp. is not responsible for any damages for user or third party resulting from lost opportunities to make a call, etc. due to breakage, malfunction, or trouble of product.
After the warranty period, if handset can be repaired, repairs will be made at cost. Further inquiries For more information on after-sales service, contact a nearby Y! Mobile Shop or Customer Service.
Customer Service For Y! Mobile handset or service information, call General Information. For repairs, call Customer Assistance.
If handset is lost/stolen, call this number immediately (international charges apply) 13
Safety Precautions Read Safety Precautions before using handset. Observe precautions to avoid injury to self or others, or damage to property. Y! Mobile Corp. is not liable for any damages resulting from use of this product.
Use with wet hands prohibited Compulsory actions Unplug from outlet Handset, USIM Card, Charger (Optional Accessory), Micro USB Cable (Optional Accessory), SD Card (Optional Accessory) (Common) Use specified Charger and Micro USB Cable only. Non-specified equipment use may cause Internal Battery to leak, overheat, burst or ignite, and may cause Charger to overheat, ignite, malfunction, etc. Do not disassemble, modify or solder handset or related hardware.
heat collects, such as under a kotatsu (blanketed warming table) or electric blanket, next to a kairo (worn warming patch), etc. May cause warping/malfunction; Internal Battery may leak, overheat, ignite or burst. Handset or related hardware may become hot to the touch, leading to burns or other problems. Do not force Charger into handset. Check Micro USB plug orientation; retry. Internal Battery may leak, overheat, burst, ignite, etc. May damage or burn out External Device Port.
Handset or related hardware may be hot to the touch; remove handset from Charger, being careful not to burn yourself. 2. Power off, being careful not to burn or injure yourself. Use in an abnormal condition may cause fire, electric shock, etc. Keep External Device Port or Earphones-Microphone Port away from liquids (tap water, beverage, sea water, pet urine, etc.) and conductive materials (pencil lead, metal strip/jewelry, hairpin, etc.).
When removing Charger from handset, hold by Micro USB plug and do not pull cord/cable. Pulling plug by cord/cable may damage cord/cable or connector and cause fire, electric shock, etc. For any skin irritation associated with use, discontinue use and consult a doctor. Metal and other materials may cause skin irritation, rashes, or itchiness depending on your physical condition. Do not touch handset or Charger for long periods during charging. May cause low-temperature burns.
Do not damage (nail, hammer, stomp, etc.) handset or subject it to strong impact. Internal Battery may leak, overheat, burst, ignite, etc. If battery fluid gets in eyes, do not rub; rinse with clean water and consult a doctor immediately. Eyes may be severely damaged. If battery fluid contacts skin or clothes, discontinue handset use and rinse with clean water immediately. May cause skin damage. If charging continues even after specified Charging Time, stop charging.
Handset Handset Display, back surface and Camera use tempered glass. Do not subject to shock (dropping, etc.) or excessive force. May cause Display, back surface or Camera to break and scatter sharp pieces. If Display or Camera breaks, be careful not to directly touch shards or broken parts. May cause injury. Do not use handset while driving or cycling. Accidents may result. Phone use while driving or cycling is prohibited by law and subject to penalty; park legally beforehand.
May temporarily affect eyesight or startle, leading to accidents. Do not cover/wrap handset with a cloth or blanket while charging. In addition, do not leave handset covered with a cloth or blanket when going to bed. Heat may collect, resulting in fire, burns, malfunction, etc. Do not use handset when it may affect a vehicle's electronic equipment. Handset use inside vehicles may cause electronic equipment to malfunction, resulting in accidents. Keep handset away from magnetic items (e.g.
Moderate handset volume when using earphones. Excessive volume may damage ears or hearing. Charger (Optional Accessory) Do not cover/wrap Charger with a cloth or blanket while charging. In addition, do not leave Charger covered with a cloth or blanket when going to bed. Heat may collect, resulting in fire, burns, malfunction, etc. Use only the specified voltage. Non-specified voltages may cause fire, malfunction, etc.
Plug Charger firmly into the outlet, keeping the plug and connector away from conductive material (pencil lead, metal strip/jewelry, etc.). May cause fire, burns, malfunction, etc. due to electric shock or short-circuiting. Do not touch Charger plug or connector with wet hands. May cause electric shock, malfunction, etc. Do not touch Charger if thunder is audible. May cause electric shock or other problems. Do not use Charger in high humidity or near water (in bathrooms, shower rooms, etc.).
May cause malfunction or injury. Keep hands and other body parts away from blades. May cause burns, electric shock, injury or malfunction.
Handset Use & Electronic Medical Equipment This section is based on "Guidelines for Use of Mobile Phones and Other Devices in Hospitals" (Electromagnetic Compatibility Conference, August 2014) and "Guidelines to safeguard implanted medical devices against radio emissions from the use of radio equipment" (Ministry of Internal Affairs and Communications). Persons with implanted pacemaker/defibrillator should keep handset more than 15 cm away.
Observe these rules inside medical facilities to avoid effects of radio waves on electronic medical equipment: ・Follow instructions regarding mobile phone use within medical facilities. ・Always turn off handset within operating rooms, intensive care units (ICU), etc. ・Even in patient rooms, lobbies, or other locations where mobile phone use is permitted, keep handset at a reasonable distance away from electronic medical equipment.
Important Product Information General Use Heat from Handset Use Camera In-Call/Transmission Cautions Urgent News (Application) Technical Regulations Conformity Certification General Use If your USIM Card or handset (with USIM Card inserted) is lost or stolen, suspend your service immediately. For details, contact Y! Mobile Customer Support, General Information.
government is required to carry handset into Cuba, Iran, North Korea, Sudan or Syria. Heat from Handset Use Handset internal temperature may increase depending on usage or environment, causing handset to become warm. (Handset may stop charging or Display brightness may be adjusted for safety.) If handset continues to be used while warm, warning appears and handset powers off after approximately 3 minutes. Exit all applications and turn off Display to let handset cool down.
Alert tones sound even in Manner mode. Alerts are not received during calls/transmissions or in poor signal conditions. Depending on usage/situation, handset may receive alerts for other areas or no alerts. Standby Time may decrease when Receive settings are enabled. Y! Mobile Corp. cannot be held liable for any damages associated with this service, including accidents resulting from received information, reception timing or reception failure.
Handset & Hardware Care Handset & Hardware Care USIM/SD Card Insertion/Removal Display (Touchscreen) Earphones-Microphone Self Check Forcing Power Off Bluetooth® Function Wi-Fi (Wireless LAN) Handset & Hardware Care Use handset within 5oC - 35oC and 35% - 90% humidity. Avoid extreme temperature or direct sunlight. Handset/Internal Battery may become warm during operation or while charging. This is normal.
Display may remain on; touching Display accidentally may end the call. Do not cover Light Sensor or place a sticker/label over it; may hinder ambient light detection, resulting in malfunction of Light Sensor. Handset Receiver is located at the center of Display upper end. If other party's voice is hard to hear during calls, hold handset so that Receiver is next to your earhole for better audibility.
Insert USIM Card and SD Card into correct openings in correct orientation. USIM Card Insertion/Removal ・Always power off before insertion/removal. ・Place USIM Card in USIM Tray beforehand. ・When removing USIM Tray, do not pull it forcefully or at an angle; damage may result. Gently pull it out horizontally from the edge. ・When inserting empty USIM Tray, do not insert it at an angle; damage may result. Check orientation of USIM Tray, then gently insert it all the way horizontally.
Close Card Slot Cover Lift Card Slot Cover in the direction of and reinsert hinge as shown ( ); place Card Slot Cover over the slot so that there is no gap between handset and Card Slot Cover, then push it in the direction of the arrow ( ) to close. When closing Card Slot Cover, push it firmly all the way from ○ area to hinge as shown ( ). Display (Touchscreen) Handset Display is Touchscreen. If Display is wet, wipe it with a soft cloth.
・Subject Display to force/pressure ・Place a sticker or shield (commercially-available protective film, privacy protector shield, etc.) on Display To improve response, calibrate Touchscreen as follows. In app sheet, (Settings) About phone Adjust touch panel Follow onscreen prompts In the following cases, Press to turn off Display, Press again to turn on Display and then operate handset.
may not function properly on handset. Do not subject Earphones-Microphone Port to strong impact while using earphones-microphone; water/dust resistance may be affected. Self Check If handset is unstable, diagnose the cause as follows. In app sheet, (Settings) Useful Self check Follow onscreen prompts Forcing Power Off If handset has stopped processing or won't respond to operation, power off forcibly as follows. (Long Press for at least 8 seconds) Release finger after vibration; handset powers off.
apparatus. Wi-Fi (Wireless LAN) Wireless LAN (hereafter "Wi-Fi") uses radio waves to enable communication between compatible devices within range. However, it is advisable for the user to configure security settings to avoid risk of data interception. Do not use Wi-Fi near electrical appliances, audiovisual equipment or office automation equipment; may affect Wi-Fi transmission speed, availability, clarity, etc. (Especially when a microwave oven is in use.
134, 136, 140) Use of 5.2 GHz or 5.3 GHz band (W52/W53) for outdoor communication is prohibited by the Radio Law. ■Simultaneous Use with Bluetooth® Wi-Fi (IEEE 802.11b/g/n) and Bluetooth® transmit on the 2.4 GHz band. Enabling handset Bluetooth® or using Bluetooth® devices near handset may affect Wi-Fi transmission speed, availability and clarity. Should interference occur, cancel handset Bluetooth ® or discontinue Bluetooth® device use. Handset supports Wi-Fi channels 1 - 13.
General Notes Portrait Rights Copyrights Radio Exposure and Specific Absorption Ratio (SAR) Information General Notes FCC Notice Portrait Rights Portrait rights protect individuals' right to refuse to be photographed or to refuse unauthorized publication/use of their photographs. Portrait rights consist of the right to privacy, which is applicable to all persons, and the right to publicity, which protects the interests of celebrities.
Radio Wave Exposure and Specific Absorption Rate (SAR) Information ■ Specific Absorption Rate (SAR) for This Product (for Japan) This mobile phone【S1】meets the Japanese technical regulations* and international guidelines for exposure to radio waves.
Use at positions other than at the ear**** This mobile phone may be used at positions other than at the ear. By using an accessory such as a belt clip holster that maintains a 1.5 cm separation with no metal (parts) between the body and the mobile phone, this mobile phone will comply with international guidelines for radio wave protection. * The technical regulation is provided in Article 14-2 of the Ministry Ordinance Regulating Radio Equipment.
This mobile phone【S1】is confirmed to comply with guidelines relating to effects of radio wave exposure as set forth by the Council of Europe (CE) and the Federal Communications Commission (FCC). Refer to the following. ■ European RF Exposure Information Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines.
■ FCC RF Exposure Information Your handset is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The guidelines are based on standards that were developed by independent scientific organization through periodic and thorough evaluation of scientific studies.
The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. The FCC has granted an Equipment Authorization for this model handset with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this model handset is on file with the FCC and can be found under the Display Grant section of (http://www.fcc.gov/oet/ea/)after searching on FCC ID APYHRO00246.
General Notes Handset Do not disassemble or modify handset. 5HJXODWRU\ LQIRUPDWLRQ ,Q VRPH FRXQWULHV UHJLRQV LQFOXGLQJ (XURSH※1 WKHUH DUH UHVWULFWLRQV RQ WKH XVH RI *+] :/$1 WKDW PD\ OLPLW WKH XVH WR LQGRRUV RQO\ ,I \RX LQWHQG WR XVH *+] :/$1 RQ WKH GHYLFH FKHFN WKH ORFDO ODZV DQG UHJXODWLRQV EHIRUHKDQG ※ 7KH IROORZLQJ (8 DQG ()7$ PHPEHU FRXQWULHV %HOJLXP %( %XOJDULD %* &]HFK 5HSXEOLF &= 'HQPDUN '. *HUPDQ\ '( (VWRQLD (( ,UHODQG ,( *UHHFH (/ 6SDLQ (6 )UDQFH
■ Description of accessories Headset, Handsfree φ3.5 audio jack, Bluetooth. Micro USB cable For charging, peripherals, etc. microSD Card microSD / microSDHC nano USIM card Y! Mobile USIM card / non-Y! Mobile USIM cards can be used after SIM-unlocking the handset. ■ Frequency range of supported bands in EU GSM 900 DCS 1800 WCDMA FDD I Tx 880.2 to 914.8 MHz Rx 925.2 to 959.8 MHz Tx 1710.2 to 1784.8 MHz Rx 1805.2 to 1879.8 MHz Tx A 1922.4 to 1977.6 MHz Rx 2112.4 to 2167.6 MHz WCDMA FDD VIII Tx 882.
■ Maximum transmit power GSM 900 DCS 1800 +32.5 dBm (Power Class4) +29.5 dBm (Power Class1) WCDMA FDD I +23 dBm (Power Class3) WCDMA FDD VIII LTE Band 1 +23 dBm (Power Class3) +23 dBm (Power Class3) LTE Band 3 Bluetooth WLAN 2.4 GHz +23.5 dBm (Power Class3) +9 dBm (Power Class1) +1 dBm WLAN 5 GHz +13 dBm ■ Battery Cautions Use specified Charger only.
■ Volume Level Caution To prevent possible hearing damage, do not listen at high volume levels for long periods. Headphone Signal Level The maximum output voltage for Music Player function, measured in accordance with EN 50332-2, is 139 mV. ■ Stand-by Mark :This symbol means the stand-by on/off. FCC Notice This device complies with part 15 of the FCC Rules.
■ FCC Information to User This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Water & Dust Resistance Handset Water & Dust Resistance Precautions Charging Cautions Care & Maintenance Washing Handset Drying Handset Handset Water & Dust Resistance Handset complies with IPX51 and IPX82 water protection standards as well as IP5X3 dust protection standard, with Card Slot Cover closed firmly. 1 IPX5 compliant means that a handset continues to function as a phone after being subjected to a water jet (approximately 12.5 liters/min.) discharged from a nozzle (inner diameter: 6.
Never open/close Card Slot Cover with wet hands or while handset is wet or has a foreign object adhered to it. Do not use Earphones-Microphone Port or External Device Port while it is wet or obstructed by sand/dirt; water/dust resistance may be affected, or malfunction, burns or fire may result due to electric shock, short-circuiting, etc. o o Handset is only water resistant against fresh/tap water between 5 C - 35 C.
short-circuiting, etc. Do not use Charger where water is regularly in use (kitchens, bathrooms, shower rooms, etc.); may cause fire or electric shock. Care & Maintenance Proper care of Card Slot Cover gasket is crucial for continued handset water/dust resistance. Observe the following: ・Do not remove or damage gasket. Keep it clean. ・If Card Slot Cover is damaged or deformed, contact a Y! Mobile Shop.
Wipe handset surface with dry cloth Holding handset firmly by its sides, shake it about 20 times When shaking handset, hold it firmly so as not to drop it.
Water may be trapped in openings; pat against a dry cloth to remove it. Leave handset on dry cloth for approximately 2 - 3 hours at room temperature Cautions When Removing Moisture Do not put a cotton swab, cloth, etc. into openings; water resistance may be affected. After Drying Procedure Do not use handset in wet conditions. Calls may fail, or moisture may transfer to clothes, bag, etc. Moisture may short-circuit Earphones-Microphone Port, External Device Port or other parts.
