0 : ENGLISH MODEL HT-SB350(BK) SOUND BAR SYSTEM OPERATION MANUAL DPII DVS is a trademark of SRS Labs, Inc. WOW HD technology is incorporated under license from SRS Labs, Inc. Note: This product is recommended for flat panel TV (LED, LCD and plasma). Accessories Please confirm that only the following accessories are included.
Special notes the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
IMPORTANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product.
Precautions IMPORTANT SAFETY INSTRUCTIONS (continued) 21) Wall or ceiling mounting - When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer. 22) Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
For U.S. customer only CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
Controls and indicators 1 2 3 4 5 ■ Front Panel 6 7 8 9 10 11 12 13 14 16 17 1 LINE IN 2 15 18 2 18 3 4 17 19 5 6 Reference page 1. Standard Indicator....................................11 2. Cinema/Game Indicator...........................11 3. Sport Indicator..........................................11 4. News Indicator..........................................11 5. Information Display 6. DTS Indicator...........................................11 7. Dolby Indicator.........................
Controls and indicators (continued) Note: Before using remote control, please remove plastic shield at battery holder. Remote control Plastic shield Battery holder TV Operation Buttons (Only SHARP TV): On/Stand-by Button Sets the TV power to “ON” or “STAND-BY”. Input Select Button (TV) Press the button to switch the input source. Volume Up and Down Buttons Turn up/down the TV volume. Channel Up and Down Buttons Switch up/down the TV channels. Note: ● Some models of SHARP TV may not be operable.
System preparation (continued) ■ Driving screws SHARP designed the speakers so you may hang them on the wall. Use proper screws (not supplied). See below for size and type. 1/8” (3.2 mm) 3/16” (5 mm) 3/8” (9 mm) Min. 7/8” (22 mm) ■ Wall mount angle fixed to the wall (Horizontal position) Fix the pattern paper to the wall in horizontal position as below. 44 mm 29 mm Wall surface Note: Make sure all screws are fully tightened.
Placing the sound bar Installation image: ■ Using other subwoofer TV VCR Place the unit as shown. You can connect a subwoofer with an amplifier to the SUBWOOFER PRE OUT socket. Audio cable (commercially available) Sound bar DVD player Notes: ● As the sound from the speaker is omni-directional, you can place it anywhere you like. However, it is recommended to place it as close to the TV as possible. ● The front panel of the unit is not removable.
Sound bar connections to TVs (continued) ■ Connecting to a TV Digital connection: To COAXIAL input socket Audio signal Coaxial digital audio cable (commercially available) Audio signal Connect to the TV using an optical digital audio cable or a coaxial digital audio cable.
AC power connection After checking all the connections have been made correctly, connect the AC power cord to the AC power input jack, then to the AC outlet. AC/DC Adaptor Cable ■ Using with the AC/DC adaptor 1 Plug the AC power cord into the AC/DC adaptor. 2 Plug the AC/DC adaptor cable into the DC INPUT jack on the unit. 3 Plug the AC power cord into an AC outlet. Notes: ● There will be no indication during power standby mode unless the ON/STAND-BY button is pressed.
General control ■ Muting The volume is muted temporarily when pressing the MUTE button on the remote control. Press again to restore the volume. ■ Preset sound mode ■ To turn the power on Press the ON/STAND-BY button. The sound mode indicator and display light up. Note: If the power does not turn on, check whether the power cord is plugged in properly. To set the unit to stand-by mode: Press the ON/STAND-BY button again.
General control (continued) The Dolby Virtual Speaker creates multichannellike sound effects. Compared with the cinema mode, the bass sound level is slightly reduced. The Dolby Pro Logic II indicator also lights up if 2ch sound signals are detected. ● DVS can only be turned on using remote control. ● If you turn ON DVS, WOW HD will automatically turn OFF. ● The DVS can be turned OFF by pressing any of the preset sound mode buttons.
General control (continued) ■ General ■ Function Symptom On the unit: When the FUNCTION button is pressed, the input LINE IN 1 source will change. Press it repeatedly to select desired LINE IN 2 input source. On remote control: Press the LINE button repeatedly to select “L1” (LINE IN DIGITAL 1 1 input) or “L2” (LINE IN 2 input). DIGITAL 2 Press the DIGITAL 1 button to select „d1” or DIGITAL 2 button to select „d2”.
Troubleshooting chart (continued) Symptom ■ If problem occurs Possible cause The unit cannot be ● Is the AC power cord turned on with the of the unit plugged in? remote control. ● Is the battery inserted? TV cannot be operated with the remote control. ● Depending on the model, some or all functions may not be operable using the remote control of this unit. In this case, use the remote control supplied with the TV.
Maintenance ■ Cleaning the cabinet Periodically wipe the cabinet with a soft cloth. Caution: ● Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the cabinet finish. ● Do not apply oil to the inside of each component. It may cause malfunctions. Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice.