ENGLISH MODEL HT-SB602 SOUND BAR HOME THEATRE SYSTEM OPERATION MANUAL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. HT-SB602 Sound Bar Home Theatre system consisting of HT-SB602 (sound bar system) and CP-SW602 (active subwoofer system). Note: This product is recommended for 60" or larger flat panel TV (LED, LCD and Plasma).
Accessories The following accessories are included. Remote Control (RRMCGA331AWSA) Subwoofer Stand x 2 Audio Cable x 1 HDMI Cable x 1 IR Transmitter x 1 Wall Mount Angle x 2 Pattern Paper NFC tag x 1 Velcro tape (hook type) x 1 Velcro tape (loop type) x 2 “AAA” size battery (UM-4, R03, HP-16 or similar) x 2 Special Notes For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited.
Precautions General Keep your equipment at least 10 cm of free space along the sides, top and back for proper ventilation. 10 cm 10 cm 10 cm 10 cm 10 cm 10 cm 10 cm Use the unit on a firm, level surface free from vibration. Keep the unit away from direct sunlight, strong magnetic fields, excessive dust, humidity and electronic/electrical equipment (home computers, facsimiles, etc.) which generate electrical noise. Do not place anything on top of the unit.
Controls and indicators (continued) Display 1 Subwoofer FRONT VIEW 2 REAR VIEW 1 DIGITAL 2 3 4 DIGITAL 3 5 6 1. Dolby Digital Indicator 2. DTS Indicator 3. Muting Indicator 1. 2. 3. 4. 5. 6. NFC detection area Power/Pairing Indicator Bass Reflect Duct Woofer SW LINK (Subwoofer Link) button AC Power Lead Sound Bar Rear Panel 1 7 5 2 1. 2. 3. 4. 5. 6. 7.
Controls and indicators (continued) 1 Remote Control 3 4 20 21 22 5 23 2 6 7 24 25 8 26 9 27 10 11 12 28 13 30 29 14 15 31 16 32 33 17 34 18 35 19 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35.
Sound bar preparation 4 To mount the sound bar on the wall Caution: Be very careful to prevent the sound bar 3.7 kg from falling when mounting on the wall. Before mounting, check the wall strength. (Do not put on the veneer plaster or whitewashed wall. The sound bar may fall.) If unsure, consult a qualified service technician. Mounting screws are not supplied. Use appropriate ones. Check all wall mount angle screws for looseness. Select a good location.
Falling prevention Safety wires (not supplied) are useful to prevent the sound bar from falling off. 2 persons are required to perform this procedure. When mounting on the wall 1 3 Loop the safety wires (not supplied) into each hole of the wall mount angle as shown. Align and fix the sound bar to wall mount angle. Wall surface 2 Wall surface Loop the safety wires from wall mount angle into each hole of sound bar as shown. 4 Tie the safety wires tightly.
Placing the system Notes: The front panel of the sound bar is not removable. The transmission distance of the wireless signal between the subwoofer and sound bar is about 10 m (32 feet), but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the subwoofer and the sound bar, the system may not operate at all, because the wireless signal cannot penetrate metal.
System connections (continued) IR (Infrared) transmitter connection If the TV’s remote sensor is blocked by the sound bar, use the IR transmitter to relay the signal to the TV. 1. Connect the IR transmitter to IR out terminal to allow the TV’s remote signal to pass through. 2. Place the infrared emitter near TV’s remote sensor (refer the operation manual of the TV for the location of the sensor ). Point the TV’s remote control at the sound bar remote sensor and operate the TV.
System connections (continued) 2. Method 2 This connection is for HDMI TV without ARC (Audio Return Channel). To HDMI input terminal TV DVD, Blu-ray disc player or similar To audio output terminal To Headphone terminal To HDMI OUT (TV ARC) output terminal To HDMI output terminal Sound Bar To HDMI input terminal To select HDMI 1, 2 or TV ARC function (Source): Sound bar operation: Press INPUT button repeatedly until “HDMI 1”, “HDMI 2” or “TV ARC” appears on the display.
Audio connections to TVs, DVD players, VCRs, etc. (continued) Connecting a TV, or DVD player, etc. Connect to the TV using an optical digital cable or an audio cable. TV To audio output terminals or Note: Make sure that the audio cable with ferrite core is connected to the sound bar AUDIO IN terminal.
Remote control (continued) Standby mode Test of the remote control Point the remote control directly at the remote sensor on the sound bar. The remote control can be used within the range shown below: Remote sensor The first time the unit is plugged in, it will enter the STANDBY mode. To cancel the STANDBY mode, press and hold the ECO MODE button (remote control) during power standby mode. The unit will enter the low power consumption mode.
General control (continued) Display brightness control Bass and Treble Control Press the DIMMER button to adjust the brightness of the display. DIMMER 1 (Display is dim) DIMMER 2 (Display gets dimmer) Bass Control 1. Press the BASS button. 2. Within 5 seconds, press the VOL (+ or –) button to adjust the bass. DIMMER OFF (Display is bright) Treble Control 1. Press the TREBLE button. 2. Within 5 seconds, press the VOL (+ or –) button to adjust the treble.
General control (continued) 3D AUDIO 1 : Sound effect that emphasizes 3D sound. APC (Auto Power Off Control) This sound bar can be set to turn off automatically if no signal is detected. (Except Bluetooth function) 1. Press the APC button repeatedly to select the time. APC 20 MIN APC 15 MIN APC 5 MIN APC 10 MIN 2. The sound bar will enter the power standby mode automatically if no signal is detected after the preset time has elapsed.
Bluetooth one touch connection via NFC About NFC technology Near Field Communication (NFC) is a set of standards for devices (smartphones/tablets) to establish radio communi cation with each other by touching/tapping them together or bringing them into close proximity. Using NFC in this product simplifies the pairing method of Bluetooth connectivity. This audio system supports NFC-enabled device with Android 4.1, Jelly Bean and higher.
Bluetooth one touch connection via NFC (continued) 3 NFC connection for audio playback Check that: Your device (smartphone / tablet) has an NFC function. NFC function on your device is turned on. Screen lock function of the device is off. This unit is not in Eco mode. 1 Playback will start automatically. Otherwise, press play (on remote control or source device). Sound will be heard from the speakers of this unit via audio streaming. Your device must be within 10 meters from the sound bar.
Listening to Bluetooth enabled devices (continued) If this unit or the source device is turned off before Bluetooth connection is completed, pairing will not be completed and the pairing information will not be memorised. Repeat step 1 onwards to start pairing again. Indicators: Indicator Condition Blinks Lights up No indication Bluetooth status In waiting or pairing mode Connected Unconnected However, the indication status is not displayed during standby mode.
Operating the TV with the remote control Troubleshooting chart You can operate Sharp TVs with this system’s remote control. Watching TV Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service centre. General Point the remote control at the TV. 1 Press the TV ( ) ON/STANDBY button to turn on the TV.
Troubleshooting chart (continued) If problem occurs during operation Symptom Possible cause Wireless connection cannot be established. Make sure there is no obstacles (especially metal) blocking between the sound bar and subwoofer. Manually re-link the sound bar and subwoofer (refer page 11). NFC / Bluetooth Symptom No sound is heard. Possible cause The unit is too far from the Bluetooth stereo audio source device. The unit is not paired with the Bluetooth stereo audio source device.
Maintenance Output power MPO: 160W (80W + 80W) (10% T.H.D.) RMS: Total 160 watts RMS: 160 W (80 W + 80 W) (10% T.H.D.) RMS: 120 W (60 W + 60 W) (1% T.H.D.) Output terminal HDMI™ output: (audio/video support up to 1080p) x 1 Input terminal 500 mV / 47 kohms Optical digital input (OPTICAL): Square type x 1 HDMI input: (audio/video support up to 1080p) x 2 Type 2 Way speaker system 5.7 cm woofer 2.5 cm Soft Dome Bluetooth Frequency band 2.400GHz - 2.
For Australia and New Zealand customers FOR LOCATION ENQUIRIES WITHIN AUSTRALIA REGARDING YOUR LOCAL SHARP APPROVED SERVICE CENTRE VISIT OUR WEBSITE AT www.sharp.net.au OR CALL SHARP CUSTOMER CARE 1300 135 022 (LOCAL CALL COSTS APPLY WITHIN AUSTRALIA) SHARP CORPORATION OF AUSTRALIA PTY LTD FOR LOCATION ENQUIRIES WITHIN NEW ZEALAND REGARDING YOUR LOCAL SHARP APPROVED SERVICE CENTRE VISIT OUR WEBSITE AT www.sharp.net.
WARRANTY Consumer Electronic Products Congratulations on Your Purchase! This Sharp product is warranted against faults in material and manufacture for the period as stated in the table below. If service is required during the warranty period, please contact your nearest Sharp Approved Service Centre. These repairs would be carried out at no charge to the owner, subject to the conditions specified herein.