User`s manual
Table Of Contents
- Safety Precautions
- Table of contents
- Chapter 1: Outline
- 1-1 Features
- 1-2 Controller
- 1-3 Measurement program
- [1] Positional deviation measurement
- [2] Degree of match inspection
- [3] Lead inspection
- [4] BGA/CSP inspection (IV-S32M/S33M)
- [5] Area measurement by binary conversion
- [6] Object counting by binary conversion
- [7] Object identification by binary conversion
- [8] Point measurements
- [9] Distance and angle measurement
- [10] Multiple position measurement (IV-S33M)
- [11] Multiple degree of match inspection (IV-S33M)
- Chapter 2 : Precautions for Use
- Chapter 3 : System Configuration
- Chapter 4 : Part Names and Functions
- Chapter 5 : Connection and Installation Methods
- Chapter 6 : Setting and Operating Outlines
- Chapter 7 : Simplified Menu Operation
- 7-1 Operation screen
- 7-2 Image display
- 7-3 Setting functions that are different with each controller
- 7-4 Setting procedures
- 7-5 Setting the operation conditions
- 7-6 Setting object types
- 7-7 Setting the shutter speed
- 7-8 Setting the positioning conditions
- 7-9 Setting the existence inspection conditions
- 7-10 Measurement triggering
- 7-11 Saving data
- 7-12 Specify the system conditions
- Chapter 8 : Specifications
- Chapter 9 : Operation Examples
- Glossary
- Appendix
- Alphabetical Index
Thank you for purchasing the SHARP IV-S30 compact image sensor camera. Read this introductory user's
manual carefully to thoroughly familiarize yourself with the functions and proper procedures for operation.
Store this user's manual in a safe place. We are confident that the manual will be helpful whenever you
encounter a problem.
In addition to this manual, there are two other IV-S30 manuals as follows. Read them in conjunction with this
manual.
Notes
IV-S30(IV-S31M/S32M/S33M)
IV-S30(IV-S31M/S32M/S33M)
User’s Manual (Introduction and Hardware: This manual)
User’s Manual (Function and Operation)
epytlaunaM stcejbusrojaM esuotwoH
03S-VI
)M33S/M23S/M13S-VI(
launaMs'resU
dnanoitcudortnI(
)erawdraH
dnaserutaef(03S-VIehtfoeniltuO-
)snoitcnuf
erawdrahehtfonoitpircseD-
dohtemputratS-
sunemdeifilpmisehtgnisunoitarepO-
.snoitacificepsecnamrofreplareneG-
03S-VIehthtiwdetniauqcaemoceB-
dna03S-VIehtllatsniotwohnraeL-
putieriw
dnagninoitisopetucexeotwohnraeL-
elpmishtiwsnoitcepsniecnetsixe
.snoitarepognittes
03S-VI
)M33S/M23S/M13S-VI(
launams'resU
dnanoitcnuF(
)noitarepO
ehtllafosnoitanalpxedeliateD-
.snoitcnuftnemerusaem
.sunemdradnatsehtgnisunoitarepO-
gnittuptuodnagnittupnifosliateD-
rehtohtiwsnoitacinummocdnaatad
.secived
gnitoohselbuorT-
tnemerusaemyficepsotwohnraeL-
GNrodoog,snoitidnocnoitcepsni/
.cte,snoitidnoctnemgduj
elbammargorpatcennocotwohraeL-
.retupmoclanosreprorellortnoc
.sruccomelborpafiodottahwnraeL-
- This manual was written with the utmost care. However, if you have any questions or
inquiries concerning the product, please feel free to contact our dealers or service agents.
- Copying all or part of this booklet is prohibited.
- The contents of this manual may be revised or modified for improvement without prior
notice.
Important
When you install the IV-S30 at an European site, use only equipment that complies with the
EMC standards. Take the steps described below using the specified cable and EMC core.
- Install a noise filter on the DC power source input lines.
- Use shielded wires for input/output lines.
- Install ferrite cores on input/output lines.