User`s manual
Table Of Contents
- Safety Precautions
- Table of contents
- Chapter 1: Outline
- 1-1 Features
- 1-2 Controller
- 1-3 Measurement program
- [1] Positional deviation measurement
- [2] Degree of match inspection
- [3] Lead inspection
- [4] BGA/CSP inspection (IV-S32M/S33M)
- [5] Area measurement by binary conversion
- [6] Object counting by binary conversion
- [7] Object identification by binary conversion
- [8] Point measurements
- [9] Distance and angle measurement
- [10] Multiple position measurement (IV-S33M)
- [11] Multiple degree of match inspection (IV-S33M)
- Chapter 2 : Precautions for Use
- Chapter 3 : System Configuration
- Chapter 4 : Part Names and Functions
- Chapter 5 : Connection and Installation Methods
- Chapter 6 : Setting and Operating Outlines
- Chapter 7 : Simplified Menu Operation
- 7-1 Operation screen
- 7-2 Image display
- 7-3 Setting functions that are different with each controller
- 7-4 Setting procedures
- 7-5 Setting the operation conditions
- 7-6 Setting object types
- 7-7 Setting the shutter speed
- 7-8 Setting the positioning conditions
- 7-9 Setting the existence inspection conditions
- 7-10 Measurement triggering
- 7-11 Saving data
- 7-12 Specify the system conditions
- Chapter 8 : Specifications
- Chapter 9 : Operation Examples
- Glossary
- Appendix
- Alphabetical Index
6-8
Setting and Operating Outlines
6
(2) Camera synchronization
When an EIA camera is used, you have to set the camera synchronization mode (internal or external
synchronization).
1 Internal and external synchronization details
1. Internal synchronization
This mode uses the CCD image capture timing inside the camera, and captures images
automatically.
- To send a captured image to the IV-S33M, first the IV-S33M must send a trigger to the
camera. Then the camera will wait until the first line from its CCD is being read to begin the
capture and image transmission. Due to this process (camera synchronization time + monitor
output synchronization time), the shutter time may fluctuate (maximun: 33.3 + 16.6 ms).
- When two cameras are connected, camera 1 and camera 2 cannot both open their shutters at
the same time. Therefore, there will be a difference in shutter timing as described above.
2. External synchronization
The IV-S33M controls the shutter speed and trigger timing in order to capture images. See the
next page for the internal/external synchronization timing charts.
• External synchronization and internal synchronization processing
• Shutter speeds of the recommended cameras
2 Setting the IV-S30EA1 and IV-S33M for use with an EIA camera
Set the IV-S30EA1 camera converter, and the IV-S33M controller to internal or external
synchronization, to match the EIA camera you have.
*For example, set the Tokyo Electronics Industries CS8320B camera dip switches as follows:
noitazinorhcnyslanretnI noitazinorhcnyslanretxE
emitrettuhSngisedaremacehtybdexiFM33S-VIehtmorfelbatteS
deepsrettuhS
aremacehthtiwsetautculF-
rotinomehtdnaemitnoitazinorhcnys
mumixam(emitnoitazinorhcnystuptuo
)aremachcaerofsm9.94
rettuhsehtnosdneped(eulavdexiF
)deeps
siht,021/1sideepsrettuhsehtnehW-
sm3.8sieulav
aremacehthtiwseiravegnargnitteS-
.detcennoc
dednemmocersaremaC 57-CXynoS
scinortcelEoykoT
B0238SCyrtsudnI
rettuhS
sdeeps
noitazinorhcnyslanretnI
)aremacehtnodetceles(
0001/1,005/1,052/1,521/1
00001/1,0004/1,0002/1
0001/1,005/1,052/1,521/1
00001/1,0004/1,0002/1
noitazinorhcnyslanretxE0061/1ot001/10051/1ot521/1
metI
sliatedgnitteS
ecnerefeR
noitazinorhcnyslanretniroF noitazinorhcnyslanretxeroF
aremacAIE
lanretnI"otteS
edom"noitazinorhcnyS
lanretxE"otteS
edom"noitazinorhcnyS
*
edom1AE03S-VI
)EDOM(hctiws
TNITXE4-4egaP
aremacM33S-VI
metsys(gnittes
)noitidnoc
AIE:noitceleSaremaC
:noitazinorhcnySaremaC
noitazinorhcnySlanretnI
AIE:noitceleSaremaC
:noitazinorhcnySaremaC
noitazinorhcnySlanretxE
13-7egaP
hctiwspiD[noitcnuF
]4WS
lanretnIesU
noitazinorhcnyS
lanretxEesU
noitazinorhcnyS
γ ]1[noitcerrocFFOFFO
]2[edomegarotsDCC)egarotsemarf(FFO)egarotsdleif(NO
]3[teserdnatratseRFFONO
]4[rettuhslaicepSFFONO
]6[tuptuoDLF/tuptuoDV)tuptuoDV(FFO)tuptuoDV(FFO