User`s manual

4-2
Positional Deviation Measurement
4
NO
±15°
±30°
±45°
360°
REGISTER NO.
15141312111009080706050403020100
× S× × × × × ×
× × × × × × × ×
STANDARD
HIGH
NO
1P-SCH
2P-SCH
1P-EDGE
2P-EDGE
1P-SCH+1P-EDGE
F C1 BRTMEAS CND SCREEN COND SAVE
SET=SELECT A MENU FOR ESC=BACK SEL=CHNG IMG TRG=FUNC
1
DTECT PRECISION STANDARD
2
REGISTER NO. 0(0∼7)
3
MODE 1P-SCH
4 DTECT ANGL ±15°
5 ANGLE UNIT 10
6
MDL 0
7 MDL 1
OBJECT TYPE COND
TYPE00
TYPE RUN COND
IMAGE-ADJ
MEA-CND(CAMERA1)
MEAS0
POSI-CORRECT
MEAS(NEW)
MEA-CND(CAMERA2)
FINAL NUM. CALC
FINAL OUTPUT COND
OBJ-TYPE I/0
OBJ-TYPE SYS.
TYPE(NEW)
SELECT OBJECT TYPE COND
+
+
MEMEASUREMENT0 SCREEN COND SAVE
NO
POSI-DEVIATION
1
MEAS SELECTION
OBJECT TYPE COND
TYPE00
TYPE RUN COND
IMAGE-ADJ
MEA-CND(CAMERA1)
MEAS0 (POSI-DEVATION)
IMG PRE-PROC
MEAS-CND
SELECT OBJECT TYPE COND
+
4-2 Setting operation
Setting the measurement conditions
Select "MAIN COND" -> "OBJECT
TYPE COND" -> "TYPE00" ->"MEA
CND (CAMERA1) " -> "MEAS0," in
that order.
On the " MEAS SELECTION" line,
select "POSI-DEVIATION" from the
popup menu. Press the ESC key to
return to the OBJECT TYPE COND
(menu tree) screen, and select the
"MEAS CND" item to enter the MEAS
CND screen.
For details, see "Chapter 8:
Setting examples using the menu
tree" in Introduction and
Hardware.
Note: "POSI-DEVIATION" (positional deviation) measurement can be specified in the "MEAS0"
(measurement 0) and "MEAS1" (measurement 1) to "MEAS4" (measurement 4) functions. If
you choose "MEAS(NEW)," the smallest available measurement number will be chosen
automatically ("MEAS1" to "MEAS4").
DTECT PRECISON
Select detection precision. You can select one of two
levels (standard/high), according to your conditions,
the desired precision level for detection results, and
the detection speed.
For details, see page 3-10.
REGISTER NO.
Enter a register number. When making positional
deviation measurements, you can select any register
from 0 to 7 (a total of 8 registers).
MODE
Select a mode for detection.
The details of each mode are as follows.
Gray search See page 3-10.
Edge detection See page 3-15.
edoMnoitceteD sliateD sledomelbasU
)enoN(ON.tcetedtonseoD
HCS-P1
)hcraestniop-1(
egamidennacsehtnitniopenofonoitaivedlanoitisopehttceteD
.hcraesyargagnimrofrepretfa,egamiecnereferelgnisaotderapmoc
ylno0ledoM
HCS-P2
)hcraestniop-2(
egamidennacsehtnistniopowtfonoitaivedlanoitisopehttceteD
.hcraesyargagnimrofrepretfa,segamiecnereferowtotderapmoc
1dna0ledoM
EGDE-P1
)egdetniop-1(
egamidennacsehtnitniopenofonoitaivedlanoitisopehttceteD
egdegnimrofrepretfa,egamiecnereferelgnisaotderapmoc
.noitceted
ylno0ledoM
EGDE-P2
)egdetniop-2(
egamidennacsehtnistniopowtfonoitaivedlanoitisopehttceteD
.noitcetedegdegnimrofrepretfa,segamiecnereferowtotderapmoc
1dna0ledoM
EGDE-P1+HCS-P1
dnahcraestniop-1(
)egdetniop-1
gnimrofrepretfatniopeno,stniopowtfonoitaivedlanoitisopehttceteD
.noitcetedegdegnimrofrepretfatniopenodnahcraesyarga
1dna0ledoM