User`s manual

Numerical Calculations
15-2
15
Setting ditails
The setting details and procedures for numerical calculations are the same for all measurement
programs with the exception of the point measurement program. In this section we explain the use of
the numerical calculations menu [NUMERIC CALC] for positional measurements.
"CHG-CALC"
Move the cursor to the "CHG-CALC" item.
Each time you press the SET key the display
in the leftmost column will alternate between
"N00 to N07" and "N08 to N15."
RUN A TEST
Pressing the SET key will store the setting
details as well as run a test
The numerecalresults of the tests will be
displayed at position [F] and the OK or NG
judgment will be dislayed at position [E].
A: TYPE
Select the type of data being calculated.
The details displayed for each measuring
program.
See page 15-5 to 15-8.
B: FORMULA
Select the formula to apply. Select formula using the left and right arrow keys and enter
numerical values using the up and down arrow keys.
The details displayed for "FORMULA" will depend on the "TYPE" selected.
For details about the items that can be selected with other measurement programs, see
pages 15-5 to 15-8.
C: UPR&LOW LIMIT
Enter the upper and lower limits for making a judgment.
D: OUTPUT
Setting the output of the calculation results. Select an output target: "NO," "Y," or "C."
The output can be set to Y0 to Y7 or C000 to C107.
- The number of styles may be set as follows, depending on the selections made in items A and
B.
N00
N01
N02
N03
N04
N05
N06
N07
＋0000002.0000
0X0＊N00
＋0000400.0000∼＋0000410.0000 ＋0000406.0000
Y0
OK
C
X
AA
B
B
CFED
NUMERIC CALC SCREEN COND SAVE F C1 BRT
[N00-N07]
CHG-CALC
1
RUN A TEST (SET KEY)
TYPE FORMULA
SET=EXEC ESC=BACK SEL=CHNG IMG TRG=FUNC
CRD-X
CRD-Y
DEV-x
DEV-y
MATCH M
ANGL-B
NUM-CAL[NC]
CNST[C]
NO
OBJECT TYPE
CALC RESULT
CNST
SUM
AVG
CBP
CBM
DEL
-
The numbers from 0 to 7 in front of the characters are registration numbers.
OBJECT TYPE
CRD [X Y]
DEV [x y]
MATCH [M]
ANGL [B]
NUM-CAL [NC]
CNST [C]
Model 0
0X0 to 7X0 / 0Y0 to 7Y0
0x0 to 7x0 / 0y0 to 7y0
0M0 to 7M0
0B to 7B
ABS / SQRT / TAN / ATAN (00 to 14)
MAX/MIN (00 to 14)
-9999999.99 to +9999999.99
Model 1
0X1 to 7X1 / 0Y1 to 7Y1
0x1 to 7x1 / 0y1 to 7y1
0M1 to 7M1
Corresponds to
page 15-4.
These are the
same as for the
other
measurement
programs.
OBJECT TYPE, CALC RESULT, CNST, SUM, AVG, CBP,
CBM, DEL
ABS, SQRT, TAN, ATAN, MAX, MIN, DEL
Selection on line
+0000000.00 (second line is not displayed)
Item selections
CRD-X, CRD-Y, DEV-x, DEV-y,
MATCH M, ANGL B
NUM-CAL [NC]
CNST [C]