Manualshelf

User`s manual

ManualsBrandsSharp ManualsDigital CameraIV-S30
281282283284285286287288289290
19-3
Computer Link
19
19-3 Register setting
Use PC register (writing: up to 512 bytes) to provide the IV-S30 with a computer link.
Setting item Applicable range of address
Write register
(up to 512 bytes)
- Sharp: 09000 to 99776
- Mitsubishi
- OMRON: DM0000 to DM9999
- Yokofawa: D00001 to D16384
See page 17-22.
Appended information (error code in an error response)
Object type number (0 to 63: 00 to 3F
(H))
Measurement number when outputting results (0 to 5)
Result output (Y0 to Y15)
Measurement function 0 using camera 1
Measurement function 0 using camera 2
Measurement function 1
Measurement function 2
Measurement function 3
Measurement function 4
Output data from measurement 0 camera 1 (block 0)
   :
Output data from measurement 0 camera 2 (block 0)
   :
Output data from measurement 1 (block 0)
   :
Output data from measurement 2 (block 0)
   
Output data from measurement 3 (block 0)
   :
:
Output data from measurement 4 (block 0)
   :
*1
*4
*3
*2
*5
*6
*7
09000
09001
09002
09003
09004
09005
09006
09007
09010
09011
09012
09013
09014
09015
：
：
：：
：
：
：：
D0000
D0001
D0002
D0003
D0004
D0005
D0006
DM0000
DM0001
DM0002
DM0003
DM0004
DM0005
DM0006
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
：
：
：：
L
H
L
H
：
：
：：
L
H
L
H
：
：
：：
L
H
L
H
19000
19001
D0256 DM0256
L
H
L
H
：
：
D00001
D00002
D00003
D00004
D00005
D00006
D00007
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
L
H
：
L
H
：
L
H
：
L
H
D00257
L
H
・
・
・
・
・
・
・
・
・
・
・
・
・
Assigned block data
Termination code (00(H): normal termination, codes other
than 00
(H) abnormal termination -See page 20-3.)
Sharp Mitsubishi OMRON ContentsYokogawa
・
・
・
*1 to *7 See the next page.
The register map shown above is established when the write start addresses have been set as shown
below.
Manufacturer
Write start address
Sharp
09000
Mitsubishi
D0000
OMRON
DM0000
Yokogawa
D00001
Enter the write start address in item " WRITE TOP ADRS," on the "COMPUTER LINK" screen, under
the "SELECT SYSTEM COND" screen.
Note 1: When a Sharp PC is used, specify an even address for the write start address.
Note 2: When 512 bytes are used for the write register in a Sharp PC, use one of the following write start
addresses.
09000, 19000, 29000, 39000, 49000, 59000, 69000, 79000, 89000, 99000
Write register map
The write register contains the following data.