R Version 2.
Thank you for purchasing the Control Terminal ZM-42/43/52/72/82 series. Please read the instruction manual carefully, and operate the product with full understanding of its functions and operation methods. For the details of each Control Terminal functions or the panel editing methods, please refer to the instruction manual for the screen edit software. - ZM-71SE Instruction Manual User's Manualt(Tutorial) Caution • In this user’s manual, ZM-42/43/52/72/82 series are referred as follows.
Safety precautions Read this manual and attached documents carefully before installation, operation, maintenance and checking in order to use the machine correctly. Understand all of the machine knowledge, safety information, and cautions before starting to use. In this instruction manual, safety precautions are ranked into "danger" and "caution" as follows. Danger : Wrong handling may possibly lead to death or heavy injury. Caution : Wrong handling may possibly lead to medium or light injury.
3) Use Danger • Don’t touch the terminal while the power is being supplied or you may have on electric shock. • Assemble the emergency stop circuit and interlock circuit outside of the ZM-42/43/52/72/82. Otherwise breakdown or accident damage of the machine may be caused by the trouble of the ZM-42/43/52/72/82. 4) Maintenance Prohibit • Don’t disassemble or modify the modules. Or fire, breakdown or malfunction may be caused.
Contents 1. Hardware Specifications 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. Special Features ........................................................................................................................... 1-1 Notes on Usage ............................................................................................................................. 1-2 System Composition .......................................................................
15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46 YOKOGAWA PC • 2 ....................................................................................................................... 2-46 YASKAWA PC • 1 .......................................................................................................................... 2-49 YASKAWA PC • 2 .....................................................................................
Hardware Specifications 1. Special Features 2. Notes on Usage 3. System Composition 4. Names of Components 5. Dimensions and Panel Cut-out 6. Mounting Procedure 7. Wiring 8. Specifications 9. Serial Connector (CN1) 10. Setting of Dip Switches 11. Modular Jack 1 & 2 12. Bar Code Reader Interface 13. Printer Interface (CN2) 14. Video Interface 15. Connection 16. Operation of ZM-** Main Menu 17. Function Switches 18. Terminal Converter (ZM-1TC) 19. Expansion I/O module (ZM-322M) 20. Card Recorder (ZM-1REC) 21.
1 Special Features 1 1-1 Special Features The Control Terminal ZM-42/43/52/72/82 series are programmable indication equipment and support tool that use LCD display and touch panel functions. They communicate by the programmable controller (thereafter PC) and programless, and you can display a variety of functions as well as inputting data by the touch panel to already programmed panel data. You can select the size of panel such as 5.7 inch display, 7.7 inch display, 10.4 inch display and 12.
1-2 2 1 Notes on Usage Notes on Usage Environmental Limits 1. Use Control Terminal at an ambient temperature of 0 to 50ºC, and a relative humidity of 35 to 85 %RH. (But, a ZM-72D/T STN multi-color display can be used at 0 to 40ºC.) 5. Never install Control Terminal in a place where impacts or vibrations may be transmitted. 0∼50℃ 50 40 30 20 10 0 2. Install a forced fan or an air conditioner to maintain the ambient temperature when it is higher than the above mentioned range. 6.
1 Notes on Usage 3. Never install Control Terminal in the same compartment as high-voltage equipment. The unit should be at least 200 mm away from highvoltage lines or power cables. 1-3 4. Securely fasten and lock every connector for each cable. Double-check this before turning the power on. k! Loc 5. In a dry environment, Control Terminal may generate a large amount of static electricity. Therefore, before touching the unit, touch a grounded metallic section to discharge the static electricity.
1 System Composition 1-4 3 System Composition System Composition / Model Indication / Peripheral Equipment System Composition The following illustration shows possible system configurations using ZM-**.
1 System Composition 1-5 Control Terminal Classification ZM-42 series ZM-43 series ZM-52 series ZM-72 series ZM-82 series Model Name Specifications ZM-42D 5.7 inches STN color, 320 × 240 dots ZM-42L 5.7 inches STN monochrome, 320 × 240 dots ZM-43T 5.7 inches TFT monochrome, 320 × 240 dots ZM-43D 5.7 inches STN color, 320 × 240 dots ZM-43L 5.7 inches STN monochrome, 320 × 240 dots ZM-52D 7.7 inches STN color, 640 × 480 dots ZM-72T 10.4 inches TFT color, 640 × 480 dots ZM-72TC 10.
1-6 1 System Composition Support tools The following options are available for useing ZM-** series more effectively Item Model Specifications Applicable models ZM-82 ZM-72 ZM-52 ZM-43 ZM-42 Network module UDP / IP protocol is supported in the module for connecting ZM-** to Ethernet. Moreover, as FL-net, it correspondences ZW-80NU to FA link protocol and cyclic transmission and message transmission (Word read/ write) are supported.
1 System Composition 1-7 ZM-71S, ZM-71SE Application software for editing display data. • ZM-71S : For Windows95/98/NT4.0 (Japanese) • ZM-71SE : For Windows95/98/NT4.0 (English) ZM-80C (Data Transfer Cable) Connects ZM-** to a personal computer, or a personal computer to ZM1REC. ZM-80PC (Printer Cable) Connects ZM-** to a printer.
1 System Composition 1-8 G P P ZM-1MD2 (ACPU/QCPU Dual Port Interface) Add-on connector with two ports, specifically designed for the connector on the MITSUBISHI's ACPU/QCPU programmer. This can improve operability of the ACPU/QCPU programmer that is directly connected. GD ZM-80NU (Network Module) It is a module for making it correspondence to the network of Ethernet and FLnet. It is possible to connect more than one sets of ZM-**s to one set of PC.
1 Names of Components 4 1-9 Names of Components Front side of ZM-42 series Rear side of ZM-42 series CN2 Front side of ZM-43 series MJ2 CN1 (+) DC24V (−) MJ1 Rear side of ZM-43 series 24VDC MJ2 CN2 1. 2. 3. 4. 5. 7. Mounting holes for fixtures Display Function keys (Refer to P1-51.) Power lamp DC power supply CN1: for PC (RS-232C, RS-422) MJ1 CN1 8. CN2: for printer 9. Dip switches 10. MJ1, 2: for data transfer and for bar-code reader and for ZM-1REC (option) 11.
1 - 10 1 Names of Components Front side of ZM-52 series Rear side of ZM-52 series (+) DC24V (−) MJ1 CN1 MJ2 CN2 Front side of ZM-72 series Rear side of ZM-72 series L 100240VAC N CN1 NC MJ2 MJ1 CN2 Front side of ZM-82 series Rear side of ZM-82 series L 100240VAC N CN1 NC MJ2 MJ1 CN2 1. 2. 3. 4. 5. 6. 7. 8. Mounting holes for fixtures Display Function keys (Refer to P1-51.
1 Dimensions and Panel Cut-out 5 1 - 11 Dimensions and Panel Cut-out Dimensions of ZM-42 series Unit : mm Rear View Top View 5 45 173.6 CN1 CN2 MJ2 Front View MJ1 Side View SYS 117.2 F2 F3 130.8 138.8 88.4 F1 F4 F5 182.5 Panel cut-out of ZM-42 series Unit : mm +0.5 -0 131 +0.
1 - 12 1 Dimensions and Panel Cut-out Dimensions of ZM-43 series Unit:mm ○Front view ○Side view SYS F2 F3 POWER 138.8 130.8 86.4 F1 F4 115.2 F5 182.5 ○Bottom view 6 ○Rear view + 24VDC 4 47.3 − ご使用時以外は剥がさないでください Do not remove this seal. unless the optional unit is mounted. MJ2 MJ1 CN1 CN2 60mm※ (Note) Since the connection positions of the serial connector CN1 differ when replaced and used from ZM-42 series, it is inconvenient with an attachment space.
1 Dimensions and Panel Cut-out 1 - 13 Dimensions of ZM-52D Unit : mm Top View Rear View 220 TB1 (+) DC 24V 60.1 ( ) CN1 6 MJ2 CN2 Front View Side View SYS F1 F4 165 F3 175 121 F2 F5 160 F6 F7 230 Panel Cut-out of ZM-52D Unit : mm +0.5 -0 +0.5 -0 165.5 220.
1 - 14 1 Dimensions and Panel Cut-out Dimensions of ZM-72 series Unit : mm Rear View Top View 288 L 100240VAC N CN1 16 76.3 NC MJ2 CN2 Front View Side View SYS F1 F3 F4 215.2 240 158 F2 F5 211 F6 F7 310 Panel Cut-out of ZM-72 series Unit : mm +0.5 -0 +0.5 -0 216.
1 Dimensions and Panel Cut-out Dimensions of ZM-82 series Unit : mm Top View Rear View 312 L 100240VAC NC CN1 16 79.8 N MJ2 CN2 Side View 245.2 270 185 Front View 247 SYS F1 F2 F3 F4 F5 F6 F7 334 Panel Cut-out of ZM-82 series Unit : mm +0.5 -0 +0.5 -0 246.
1 Mounting Procedure 1 - 16 6 Mounting Procedure Mounting Procedure 1. Cut out the mounting panel (Max. thick: 3.2 mm) to match the dimensions shown below. Mounting panel (In case of ZM-52D) Unit : mm 174 220.5 +0.5 -0 +0.5 -0 Cut-out 289 F1 165.5 +0.5 -0 ZM-52D 131 ZM-42 Series ZM-43 Series SYS +0.5 -0 +0.5 -0 220.5 +0.5 -0 313 +0.5 -0 165.5 -+0.5 0 F2 F3 ZM-72 Series F7 ZM-82 Series 246.2 F6 216.2 F5 +0.5 -0 +0.
1 Wiring 7 1 - 17 Wiring Electrical Wiring Connects the cable for power supply to TB1 on the rear side of ZM-**. DC24V MJ2 TB1 (+) (-) MJ1 Power supply DC24V±10% CN1 (+) DC 24V (-) CN2 Earth ZM-42/43 Series, ZM-52D Type : AC100-200V L 100240VAC N NC TB1 L CN1 Power supply 100-200VAC N MJ2 NC MJ1 CN2 Earth ZM-72 Series/ZM-82 Series Type Screw Screw Size Torque (N • m) Clamp Terminal (Unit : mm) ZM-42/43 Series, ZM-52D M3.5 0.49 7.0MAX 7.0MAX ZM-72 Series/ZM-82 Series M3.
1 - 18 1 Wiring Grounding This equipment must be earthed. ZM-** An independent earth pole shall be used for Control Terminal. (Earth construction is the class-3 grounding. The level of grounding resistance should be less than 100 Ω.) Use a cable which has a nominal cross section of more than 2mm2 for grounding. Grounding point shall be near the Control Terminal to shorten the distance of grounding wires.
1 Specifications 8 1 - 19 Specifications General Specifications Type Item ZM-43 series ZM-42 series 24V DC Rated Voltage 24VDC 10% Permissible Range Power Supply ZM-52D of Voltage 10ms or less Permissible Momentary Power Failure Demand 10W or less 20W or less 17A 1ms 5A 1.
1 Specifications 1 - 20 Type Power Supply Item Rated Voltage 100 to 240V AC 100 to 240V AC Permissible Range 85 to 265 VAC 85 to 265 VAC (47 to 440 Hz) (47 to 440 Hz) Permissible Momentary Power Failure 20ms or less 20ms or less Demand 45 VA or less 50 VA or less Rushed Electric Current 20A: 100 VAC 30A: 200 VAC 20A: 100 VAC 30A: 200 VAC of Voltage With-stand voltage Between AC external terminals and FG: 1500V AC per min.
1 Specifications 1 - 21 Display Specifications Item Type ZM-42L ZM-42D ZM-43D ZM-43L ZM-43T ZM-52D STN moSTN moDisplay Device nochrome STN color nochrome STN color TFT color STN color LCD LCD LCD LCD LCD LCD 320 × 240 640 × 480 Resolution W × H (dots) Dot Pitch W × H (mm) 0.36 × 0.36 0.12 × 0.36 0.36 × 0.36 0.12 × 0.36 0.36 × 0.36 0.082 × 0.246 W × H (mm) Color (5.7 inches) (7.
1 - 22 1 Specifications Display Function Specifications Item Display Language Characters Specifications Japanese Eng./W.
1 Specifications 1 - 23 Function Performance Specifications (All the ZM-** series) Specifications Item Screens Max. 1024 Screen Memory FP-ROM (flash ROM), Appox.
1 - 24 1 Specifications Touch Panel Specifications Item Specifications Switch Resolution Analog, 1024(W) ¥ 1024(H) Form Resistance film form Life of Touch Panel Use of one million times or more Function Switch Specifications Item Specifications Number of Switches 8 (6 for ZM-42/43) Type of Switch Pressure sensitive switches Life of Switch Use of one million times or more Interface Specifications Item Specifications Serial Interface RS-232C, RS-422/485 for connecting PC Asynchronous ty
1 Specifications 1 - 25 Compatible PC for connection Maker Sharp PC Model J-board, JW10, JW20/20H, JW30H W70H/100H, JW50/70/100, JW50H/70H/100H MITSUBISHI A Series/Q Series link module/CPU port, FX1/2 Series OMRON C Series, COM Series, CV Series HITACHI HIDEC H300/700/2000, S10 Matsushita FP Series YOKOGAWA FA500, FA-M3 YASUKAWA GL40/60/70 TOYOPUC PC2/2J, L2 FUJI F70/80H/120H, NS/NJ, FLEX-PC CPU/COM Koyo SU-5/6, SG-8 Allen-Bradley PLC-5, SLC500 GE Fanuc Series 90-30 TOSHIBA EX100/
1 Serial Connector (CN1) 1 - 26 9 Serial Connector (CN1) CN1 is used for communicating between a PC and a ZM-** (RS-232C, RS-422/485). Serial Connector (CN1) The pin arrangement of serial connector is as follows: L 100240VAC N NC CN1 CN1(Dsub 25pin 凹) MJ2 1 MJ1 CN2 Signal 1 FG Frame ground 2 SD RS-232C send data 3 RD RS-232C receive data 4 RTS RS-232C RTS request to send 5 CTS RS-232C CTS clear to send Not used 6 14 SG 7 8 13 Contents Pin No.
1 Serial Connector (CN1) 1 - 27 RS-422 In case of RS-422, +SD and -SD, and +RD and -RD form a pair. Use SG if possible. Connect the shielded cable to pin No. 1 or the connector case cover. Use Terminal converter ZM-1TC which is the optional equipment in case of using terminal blocks in RS422/485 connection. Specify terminal resistance by the dip switches on ZM-**. (Refer to the next page.) ZM-** (CN1) To the RS-422 port of the PC link module Shielded cable Signal Pin No.
1 - 28 1 Setting of Dip Switches 10 Setting of Dip Switches Setting of Dip Switches (DIPSW) ON 1 Memory Extension 2 (invalid for ZM-42) 2 3 4 5 6 7 8 SD terminal resistance of pin No. 12 and 13 in CN1 Not used RD terminal resistance of pin No. 24 and 25 Terminal resistance of MJ1(modular jack 1) Setting of Terminal Resistance • Set DIPSW 7 and 8 ON in case of connecting ZM-** to PC by 4-wire connection of RS-422/485.
1 Modular Jack 1 & 2 11 1 - 29 Modular Jack 1 & 2 Modular Jack 1 & 2 (MJ1/2) The right diagram is the pin arrangement and the signal name of modular jack 1 & 2. MJ1/2 12345678 Pin No. 1 2 3 4 5 6 7 8 Signal +SD/RD -SD/RD +5V +5V 0V 0V RXD TXD External power supply +5V Max. 150mA Setting of Modular Jack 1 & 2 (MJ1/MJ2) Specify the use of MJ1/MJ2 by the screen edit software ZM-71SE. Select [System Setting] from [Item], and click [Others]. The [Others] dialog is displayed.
1 - 30 1 Bar Code Reader Interface 12 Bar Code Reader Interface It is possible to receive the signal from a bar code reader by connecting a bar code reader to ZM-** via the modular jack (MJ1/MJ2) of ZM-** series. To connect a bar code reader to ZM-** via MJ1/MJ2, use the cable use the Bar Code Connecting Cable ZM-80BC which is the optional equipment made only by demand.
1 Printer Interface (CN2) 13 1 - 31 Printer Interface (CN2) When a printer is connected to ZM-** via the connector (CN2), it is possible to hard-copy the screen display of ZM-**, the data sheet, or the sampling data. For the connection of the printer and ZM-**, apply the printer cable ZM-80PC (sold separately) which matches the 36-pin parallel interface.
1 - 32 1 Video Interface 14 Video Interface When a video or a CCD camera is connected to the optional ZM-** which has a video interface, the image which is taken by a video or a camera is displayed directly in a screen of ZM-** series (only in case of ZM-72TV/TVC, ZM-72TSV/TSVC, ZM-82TV/TVC).
1 Connection 15 1 - 33 Connection 15-1 Connection with Sharp PLC ZM-** [1] 1 : 1 Link Communication PLC One ZM-** and one PLC are connected. RS-232C or RS-422(RS-485) [2] 1 : n Link Communication (Multi-drop) One ZM-*2 and multiple PLCs are connected.
1 - 34 1 Connection Multi-drop Communication (RS-485) Refer to the PLC manual of each manufacturer for connection. The following example describes how one ZM-** is connected to three PLCs made by MITSUBISHI. See MITSUBISHI’s manual for further details. ZM-** (CN1) Link module Link module Link module Signal Pin No.
1 Connection MITSUBISHI : AnA/N/U series MITSUBISHI : QnA series MITSUBISHI : ACPU Port MITSUBISHI : FX series MITSUBISHI : QnACPU Port MITSUBISHI : QnHCPU Port (A) MITSUBISHI : QnHCPU Port (Q) MITSUBISHI : FX series(A prt) MITSUBISHI : FX2N series MITSUBISHI : FX1S series OMRON : SYSMAC C OMRON : SYSMAC CV OMRON : SYSMAC CS1 SHARP : JW series SHARP : JW100/70H COM Port SHARP : JW20 COM Port HITACHI : HIDIC-H HITACHI : HIDIC-S10/2 alpha HITACHI : HIDIC-S10/ABS MATSUSHITA : MEWNET YOKOGAWA : FA500 YOK
1 - 36 1 Connection (2) Multi-link 2 Multiple ZM-** and a PLC are connected. (n=1 to 32) ZM-** 1 ZM-** 2 ZM-** 3 ZM-** n * The connections shown below are not recommended.
1 Connection 1 - 37 Use the terminal converter (ZM-1TC), the optional equipment made by Sharp Corporation for RS-485 connection. • When the ZM-1TC terminal converter is used. Set the dip switch (SW1) of ZM-1TC as 2-wire connection.
1 - 38 1 Connection 15-2 Connection to Ethernet/FL-net When a network module ZM-80NU is mounted in ZM-43/52/72/82 series, it is connectable with Ethernet/FL-net ( ZM-42 series is not connectable.) In addition, in the program version 1.2.0.0 or later of ZM-43/52/72/82 series, the version 1.2.0.0 or later of ZM-71SE corresponds to Ethernet/FL-net.
1 Connection 1 - 39 15-3 Connection by general purpose serial communication The ZM-** can connected with a general purpose computer using the user program (exclusive command use). Refer to ZM (general purpose serial) user’s manual in detail. [1] When a computer and ZM-** are 1 : 1 - RS-232C can use it by less than 15m, and RS-422 (485) can use transmision distance by less than 500m. - Interruption processing can be used.
1 Operation of ZM-** Main Menu 1 - 40 16 Operation of ZM-** Main Menu When the power of ZM-** is turned ON for the first time, the screen on the below left is displayed. After transferring the screen data to ZM-**, the following "Main Menu" is displayed. When power is turned ON for the first time: "Main Menu" after trasferring data ZM-72T Main Menu System Information SYSTEM PROG. VER.1.000 Screen Data Information Size : 786432 1998- 9- 1 FONT VER.1.000/1.000/1.
1 Operation of ZM-** Main Menu System program version 1 - 41 Model name of ZM-** Font data version Data size ZM-72T Main Menu System Information SYSTEM PROG. VER.1.000 Screen Data Information Size : PC type and comment specified by the panel editor 786432 1998- 9- 1 FONT VER.1.000/1.000/1.000 JAPANESE 32 Own Stat.No.: 1 V6 Total: 2 Retry: 10 PC I/F driver version and name Error: Stop Time-Out: 0.
1 Operation of ZM-** Main Menu 1 - 42 I/O Test When the switch 'A' on the "Main Menu" is pressed, the following "I/O Test" is displayed. This is the test menu to check only ZM-** hardware. Memory-Card I/O Test B E C Press the [I/O Test] switch. D I/O Test Main Menu SYS F-1 Printer Check Switch Check F-2 A F-3 Self-Loop Test Please refer to the manual, "Hardware Specifications".
1 Operation of ZM-** Main Menu 1 - 43 A. Self-loop Test This is the test menu to check the signals necessary for ZM-** to communicate with PC or a personal computer by using only ZM-**. Signal Test of RS-232C in CN1 Select [CN1] and [RS-232C] in [Communication Port] by pressing each switch. Communication Port CN1 RS-232C MJ1 RS-485 MJ2 • Loop-back Test Check the signals, [SD] and [RD]. 1. Jump pins, 2 and 3 of CN1. 2.
1 - 44 1 Operation of ZM-** Main Menu Signal Test of RS-485 in CN1 Select [CN1] and [RS-485] in [Communication Port] by pressing each switch. Communication Port CN1 RS-232C MJ1 RS-485 MJ2 • Loop-back Test Check the signals, [SD] and [RD]. 1. Jump each pin, 12 and 24, 13 and 25 of CN1. 2. The test is OK, if the [OK] lamp turns on when the [Self-Loop Test] switch is pressed. CTS RTS CTS RTS NG OK NG OK Self-Loop Test Self-Loop Test • Test of CTS/RTS Check the signals, [CTS] and [RTS]. 1.
1 Operation of ZM-** Main Menu 1 - 45 Signal Test of RS-232C in MJ1 and MJ2 Select [MJ1] (or [MJ2]) and [RS-232C] in [Communication Port] by pressing each switch. Communication Port CN1 RS-232C MJ1 RS-485 MJ2 • Loop-back Test Check the signals, [SD] and [RD]. Execute the test by connecting the data transfer cable (ZM-80C) to CN1. 1. Set the adaptor, ADP25-9, which is attached to ZM-80C, to ZM-80C. And connect the modular jack side of ZM-80C to MJ1 (or MJ2), ADP25-9 side of ZM-80C to CN1.
1 Operation of ZM-** Main Menu 1 - 46 B. Printer Check Check the signal for a printer. The test is OK if the test printout is executed satisfactorily when connecting ZM-** to a printer and pressing this [Printer Check] switch. [Example] C. Switch Check Check the reaction of the touch switches on the ZM-** panel. When the [Switch Check] switch is pressed, the following screen is displayed. The switch check screen is displayed.
1 Operation of ZM-** Main Menu 1 - 47 D. Test of SYSTEM & Function Switches Check the eight switches (six switches for ZM-42/43) placed vertically on the right side of the ZM-** panel. The test is OK if the lamps on the screen turn ON when each switch is pressed. SYS SYS F-1 F-1 F-2 F-2 F-3 F-3 The test is OK when the [F-4] lamp is lit. F-4 F-4 Press the [F4] switch. F-5 F-5 F-6 F-6 F-7 F-7 E. Main Menu Pressing this [Main Menu] switch leads to the previous [Main Menu].
1 - 48 1 Operation of ZM-** Main Menu Memory-Card When the [Memory-Card] switch on the "Main Menu" is pressed, the following "Memory-Card" is displayed. This screen is to transfer the screen data between ZM-** and a memory-card. Memory-Card I/O Test The "Memory-Card" screen is displayed. Press the [Memory-Card] switch.
1 Operation of ZM-** Main Menu 1 - 49 2) Data Selection, Transfer Pressing each switch leads to selection of the target for data transferring. (Possible to select multiple items.) Data Selection Transfer Memory-Card Memory-Card Main Menu Close Memory-Card Information Main Menu Close Memory-Card Information Port Selection Port Selection V6 Program : Modular Jack Memory-Card Version:-.--MJ1 Socket Font Data : Version:-.---/-.---/-.--I/F Driver : Version:-.
1 - 50 1 Operation of ZM-** Main Menu Message Display in Data Transferring If an error occurs during transferring data, the message display window shown on the right is displayed. The kinds and the contents of the messages are as shown below. Message Work nomally finished. OK Contents Work normally finished. The specified operation has been concluded normally. ZM-1REC not connecting ZM-1REC is not connecting when selecting a modular jack.
1 Function Switches 17 1 - 51 Function Switches Type [SYS], [F1], [F2], [F3], [F4], [F5], [F6], [F7] (ZM-42/43 : [SYS], [F1] to [F5]) S Y S R E M The [SYS] switch By pressing this switch, the functions of the switches [F1] to [F7] are defined. The type of the [SYS] switch is alternate. When this switch is pressed once, the switch menu is displayed by the side of the function switches [F1] to [F5], and each function switch corresponds to an item on the displayed switch menu.
1 - 52 1 Terminal Converter (ZM-1TC) 18 Terminal Converter (ZM-1TC) Use the terminal converter ZM-1TC when connecting the ZM-42/43/52/72/82 series and PC by the RS-422/ 485 terminal block. Size 25 65 34.7 Installation (+) DC24V (−) 1. Make sure that the power of ZM-42/ 43/52/72/82 series is OFF. 2. Install the ZM-1TC to the serial connector (CN1) of the ZM-42/43/52/ 72/82 series. 3. Settle the ZM-1TC by the module mounting screw.
1 Terminal Converter (ZM-1TC) 1 - 53 Connection Connecting the RS-422 communicating cable • Choose 4-line or 2-line system by the ZM-1TC DIP switch (SW1) • Connect the cable if SG exists. • Connect the shield line to FG. • End resistance is set by the dip switch located on the back side of ZM-** body. • Be sure to put the attached cover to ZM-1TC when the connection is terminated.
1 Expansion I/O module (ZM-322M) 1 - 54 19 Expansion I/O module (ZM-322M) The expansion I/O module ZM-322M is used on the ZM-72/82 series as the external I/O of the PC. (Input 16 points, output 16 points) Attached unit • DI/DO connector Used by connecting to the connector pin, and mounting it to the connection part of the expansion I/O module. Size 74 125.
1 Expansion I/O module (ZM-322M) 1 - 55 How to use To use the ZM-322M, refer to the {[P2] menu} in [Chapter 2 System Setting] of the ZM-71SE instruction manual. Position of the DI/DO connector pin DC24V The positioning of the DI/DO connector pin is as follows. Connect it by referring the drawing. COM IN IN IN IN IN 1 12 IN 13 22 IN IN IN 23 34 IN DI/DO connector (attached connector) Input In No. Pin No.
1 - 56 1 Card Recorder (ZM-1REC) 20 Card Recorder (ZM-1REC) Used for the backup of the panel data or recording the memory manager function and the data longing function. 94 92 25 LED condition display Modular connector Memory card connector AC adapter connector Memory Card connector SRAM and flash memory card are used as described in the chart below. (JEIDA Ver4.
1 Cable for transporting the panel (ZM-80C) 21 1 - 57 Cable for transporting the panel (ZM-80C) ZM-80C is the cable that transports panel data between ZM-42/43/52/72/82 series as well as ZM-41/70 series and the personal computers. When using, you need to have a Windows screen edit software ZM-71SE. The convertible adapter ADP25-9 and ADP25-M are attached to ZM-80C. Examples of the using cable and convertible adapter.
1 - 58 1 Printer Cable (ZM-80PC) 22 Printer Cable (ZM-80PC) ZM-80PC is the cable that connects ZM-42/43/52/72/82 series to the printer. You can hard copy the panel of ZM-42/43/52/72/82 as well as registered list/ sampling data. Printer ZM-42/43/52/72/82 Series Half pitch 36pin Centronics 36pin • The length of the ZM-80PC cable is 2.5 meters.
1 2 Port Adapter (ZM-1MD2) 23 1 - 59 2 Port Adapter (ZM-1MD2) By mounting to the GPP port of Mitsubishi PC, ZM-1MD2 acts as an module that connects and communicates between GPP (programming tool) and ZM-42/43/52/72/82 series. Since it is possible to connect without the link module of the Mitsubishi PC calculator, the cost saving of the hardware machines became possible.
1 - 60 1 2 Port Adapter (ZM-1MD2) When connecting 2 units together MITSUBISHI A Series PC Q Series CPU Connecting cable (Mitsubishi made : optional) SYSTEM F 1 F 2 F 3 F 4 F 5 F 6 GD G P P F 7 POWER This ZM becomes a bit faster -M RUN ZM Series DD Connect the connector which is found on the back side directly to the CPU port. GD 123 Slide switch Use when select the connection model.
1 2 Port Adapter (ZM-1MD2) 1 - 61 Attached metal fittings of ZM-1MD2 When connecting ZM-1MD2 to the small type (A1S, A2US, etc,) of A series PC made by Mitsubishi, use the unit by mounting the attached metal fittings. MELSEC Axsxxx MELSEC AxS CPU STOP POWER RUN ERROR L.CLR RUN RESET RESET MITSUBISHI MITSUBISHI GPP Insert the metal fitting as shown in the drawing.
1 - 62 1 2Port Adapter (ZM-1MD2) Size drawing of ZM-1MD2 4.1 24.1 4.1 100 GPP 74 1 ON 1 12.7 1 38.1 Devise mounting screw Lot Seal 8.
1 Expansion Memory (ZM-4EM) 24 1 - 63 Expansion Memory (ZM-4EM) 1 M O M R E J P 1 -M 7 9 V F C N C 1 Installation P 0 2 0 0 4 F R O M 0 About 900K bytes (1.2 M byte if 32 dot font is not in use) inside the flash memory that has been installed in the main body of ZM-52/72/82 series are used as the panel data memory. If you install ZM-2EM/4EM to the main body of ZM-52/72/82 series, an additional 2M/4M bytes are installed to the panel data memory.(ZM-2EM is discontinued production.) 1.
1 - 64 1 Expansion Memory (ZM-43EM) 25 Expansion Memory (ZM-43EM) An expansion memory ZM-43EM is the extension board used for which increases the screen data memory of ZM-43T/43D/43L. When ZM-43T/43D/43L is mounted, 4 M bytes of screen data memory can be extended. Correspondense models ZM-43 series (ZM-43T/43D/43L) Software version - Use the version 1.2.0.0 or later for program version (SYSTEM PROG. VER.) of the ZM-43T/43D/43L. - Use the verison 1.2.0.0 or later for ZM-71SE.
1 Expansion Memory (ZM-43EM) 1 - 65 Kinds of memory expansion In the ZM-43EM, there are two kinds of extension methods (additional memory 1 and 2) according to setup the DIP switch of ZM-main body. 1. Additional memory 1 Set OFF the DIPSW “1” of ZM main body. - As shown in the following table (*1), the amount of memories increases by the capacity of ZM-43EM. 2. Additional memory 2 Set ON the DIPSW “1” of ZM main body.
1 - 66 1 Expansion Memory (ZM-43SM, ZM-80SM) 26 Expansion Memory (ZM-43SM, ZM-80SM) An expansion memory ZM-43SM/80SM is a memory for extension in which the calendar and SRAM backup memory of ZM-43/52/72/82 were carried. Model name Correspondense model ZM-43SM ZM-43 series ZM-80SM ZM-52/72/82 series - This expansion memory cannot be used for ZM-42 series. The component of ZM-43SM/80SM is as follows.
1 Expansion Memory (ZM-43SM, ZM-80SM) 1 - 67 Installation Please attach ZM-43SM/80SM in ZM-43/52/72/82 in the following procedure. i J A PA N SANYO + CR2430 CE TS M n O 2- L 1. The battery (CR2430) of an attached article is turned to the socket of ZM-43SM/80SM, "+" side is turned upwards, and it sets. In case it sets, as a battery is pushed in a plug and the direction of "+" side, "-" side also inserts it in "+" side.
1 - 68 1 Expansion Memory (ZM-43SM, ZM-80SM) The exchange method of a battery You should prepare the following battery for exchange, and it exchanges for it in the following procedure. Model type CR2430 Specifications ・Coin type lithium primary battery (recommend : made by SANYO) 1 In case battery exchange is carried out, ZM-71SE are used (cable : ZM-80C) and backup of the data stored in ZM-43SM/80SM is taken. 1. ZM-71SE is started. 2. [Transmission] icon is clicked. [Transmission] dialog is displayed.
Connection to Link Module 1. Sharp PC 2. MITSUBISHI PC • 1 3. MITSUBISHI PC • 2 4. MITSUBISHI PC • 3 5. MITSUBISHI PC • 4 6. MITSUBISHI PC • 5 7. MITSUBISHI PC • 6 8. MITSUBISHI PC • 7 9. OMRON PC• 1 10. OMRON PC• 2 11. HITACHI PC • 1 12. HITACHI PC • 2 13. Matsushita PC 14. YOKOGAWA PC • 1 15. YOKOGAWA PC • 2 16. YASKAWA PC • 1 17. YASKAWA PC • 2 18. TOYOPUC PC 19. FUJI PC • 1 20. FUJI PC • 2 21. FUJI PC • 3 22. FUJI PC • 4 23. Koyo PC 24. Allen-Bradley PC • 1 25. Allen-Bradley PC • 2 26.
2 Sharp PC 1 Sharp PC Link module The following are the link module and communication port that are possibly connected.
2-2 2 Sharp PC Switch Setting of Link module (1) Switch setting of ZW-10CM, JW-10CM and JW-21CM Contents Switch Setting SW0 4 Comand mode SW1 1 Station address (lower half) SW2 0 Station address (upper half) OFF Not used SW3-2 ON 4-wire system SW3-3 OFF Not used SW3-4 ON Even parity SW3-1 SW4 0 SW7 ON Baud rate:19200 bps Temination resistance provided (2) Switch setting of Z-331J/332J Switch Setting SW0 4 Computer link SW1 1 Station address (lower half) SW2 0 Station
2 Sharp PC (2) System memory setting of JW-32CUH/H1/M1, JW-33CUH/H1/H2/H3, Z-51J/512J • Communication port 1 (PG/COMM 1 port) System memory Setting #234 30 (H) Contents Stop bit : 2 bit, Parity : Even Baud rate:19200 bps #235 01 (H) Station address • Communication port 2 (PG/COMM 2 port) System memory Setting Contents Stop bit : 2 bit, #236 30 (H) #237 01 (H) Parity : Even Baud rate:19200 bps Station address (3) System memory setting of JW-1324K/1342K, JW-1424K/1442K and JW-1624K/1642K • Co
2-4 2 Sharp PC Available Memory Memory Bit Write X9XXX (Register) XXXXX (Relay) EXXXX (Register [Self-diagnosis]) bXXXX (Timer/Counter [current value) F1 (File Register) F2 (File Register) F3 (File Register) Available: Unavailable: TYPE Remarks 0 1 2 3 4 5 6 as word device [Caution] Pay attention to the following cautions when applying the indirect address-assign of the macro command by the register x9xxx(memory type :0) (Refer to P14-23 of the ZM-71SE instruction manual) 1) When applying the ZM
2 Sharp PLC Wiring Indicate the connection of ZM-** and each module. CN1 is used alternately with RS-422. RS-422 • Connection with ZW-10CM, JW-10CM and JW-21CM ZW-10CM JW-10CM JW-21CM ZM-** (CN1) Signal name No. Signal name +SD 12 L3 -SD 13 L4 +RD 24 L1 -RD 25 L2 FG 1 SHIELD * Use twist shielded cables GND Earth • Connection with JW-70CU/100CU, JW-70CUH/100CUH, JW-22CU ZM-** (CN1) JW-22CU JW-70CU/100CU JW-70CUH/100CUH (Communication Port) Signal name No. Signal name No.
2-6 2 Sharp PLC • Connection with JW-32CUH/H1, JW-33CUH/H1/H2/H3, Z-512J ZM-** (CN1) JW-32CUH/H1 JW-33CUH/H1/H2/H3 Z-512J PG/COMM1 Port PG/COMM2 Port Signal name No. Signal name +SD 12 RD (+) No. 9 -SD 13 RD (-) 10 +RD 24 SD (+) 3 -RD 25 SD (-) 11 FG 1 FG 1 * Use twist shielded cables • Connection with JW-1324K/1342K, JW-1424K/1442K, JW-1624K/1642K [In case of connecting to the communication port] ZM-** (CN1) Signal name No.
2 Sharp PLC RS-232C • Connection with JW-70CU/100CU, JW-70CUH, JW-22CU ZM-** (CN1) JW-22CU JW-70CU/100CU JW-70CUH/100CUH (Communication Port) Signal name Pin No. Signal name Pin No. FG 1 FG 1 SD 2 RXD 3 RD 3 TXD 2 RS 4 SG CS 5 SG 7 Short Terminal 7 12 14 * Used shielded cables • Connection with Z-311J/312J ZM-** (CN1) Z-311J/312J (Host communication port T1) Signal name Pin No. Signal name Pin No.
2-8 2 2 MITSUBISHI PC • 1 MITSUBISHI PC • 1 (A/Q series link unit) Available PC ZM-71SE Model Setting PC A2A, A3A Link Unit AJ71C24-S6 AJ71C24-S8 AJ71UC24 A2U, A3U, A4U AJ71UC24 A1, A2, A3 A1N, A2N, A3N A3H, A3M, A73 AJ71C24 AJ71C24-S3 AJ71C24-S6 AJ71C24-S8 AJ71UC24 AnA/N/U series A0J2, A0J2H RS-232C [Wiring Diagram 2] RS-422 [Wiring Diagram 3] A0J2C214-S1 A1SJ71UC24-R2 RS-232C [Wiring Diagram 1] A1SJ71UC24-R4 RS-422 [Wiring Diagram 3] A1SJ71UC24-PRF RS-232C [Wiring Diagram 1] A1SJ71C24-
2 MITSUBISHI PC • 1 2-9 Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: A series link unit Setting of PC Comm. Parameter of ZM-** Baud Rate 19200bps 19200bps Port 0 for both STATION × 10 and ×1 0 Item Parity *1 Even Even MODE1 Trans. Mode 1 Transmission Control Mode RS-232C RS-422 MODE5 Trans.
2 - 10 2 MITSUBISHI PC • 1 Switch Setting The following is an example to show the settings for both rotary dip switches and dip switches on PC. Signal Level: RS-232C, Baud Rate: 19200bps, Trans. Mode: Trans. Mode 1 ON SW11 SW12 AJ71UC24 SW13 STATION No ×10 STATION No ×1 MODE B C D E B C D E B C D E A 9 8 7 6 5 4 3 A 9 F 0 1 2 8 7 6 5 4 3 SW14 A 9 F 0 1 2 8 7 6 5 4 3 SW15 F 0 1 2 SW16 ON OFF SW17 SW18 SW21 SW22 SW23 SW24
2 MITSUBISHI PC • 1 2 - 11 Available Memory Available: Memory Bit Write TYPE D (data register) W (link register) 1 R (file register) 2 TN (timer/current value) Remarks 0 3 CN (counter/current value) 4 SPU (special unit) 5 M (internal relay) 6 L (latch relay) 7 B (link relay) 8 X (input relay) Y (output relay) 10 TS (timer/contact) 11 TC (timer/coil) 12 CS (counter/contact) 13 Slot No.
2 - 12 2 MITSUBISHI PC • 1 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 CD 1 RD 3 RD 2 RS 4 SD 3 CS 5 SG 5 SG 7 DR 6 RS 7 CS 8 D-sub 9pin(Male: ) * Use twist shielded cables.
2 - 13 2 MITSUBISHI PC • 1 RS-422 Wiring Diagram 3 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 SDA +SD 12 SDB -SD 13 RDA +RD 24 RDB -RD 25 SG * Use twist shielded cables. Wiring Diagram 4 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SG 7 RDA 2 +SD 12 SDA 3 -SD 13 DSRA 4 +RD 24 DTRA 5 -RD 25 SG 7 RDB 15 SDB 16 DSRB 17 DTRB 18 D-sub 25pin(Male: 20 21 * Use twist shielded cables.
2 - 14 3 2 MITSUBISHI PC • 2 MITSUBISHI PC • 2 (A/QnA series CPU port) Connection Connect to the A/QnA series CPU port. The communication parameter setting of ZM-** is done automatically.
2 MITSUBISHI PC • 2 2 - 15 Available Memory Available: Memory Bit Write TYPE D (data register) W (link register) 1 R (file register) 2 TN (timer/current value) 3 Remarks 0 CN (counter/current value) 4 SPU (special unit) 5 M (internal relay) 6 L (latch relay) 7 B (link relay) 8 X (input relay) Y (output relay) 10 TS (timer/contact) 11 TC (timer/coil) 12 CS (counter/contact) 13 Slot No.
2 - 16 2 MITSUBISHI PC • 2 Notes on direct connection with the CPU port of A/Q series CPU Note According to our noise tests, the attachment of a ferrite core improves noise voltage by 650 to 900V and aids in preventing communication errors. For safer operation, be sure to attach the ferrite core to the cable. Take appropriate measures to eliminate any noise from entering the communication cable between the ZM-** and MITSUBISHI A/QnA series CPU.
2 - 17 2 MITSUBISHI PC • 2 Notes on using ZM-1MD2 (Dual Port Interface) (See page 1-60) As the ZM-1MD2 is powered by a CPU, check that the electric capacity of the CPU is at 5V (power consumption: max. 350mA). The distance between the CPU and the ZM-1MD2 should be as short as possible (max. 1~1.5m). For wiring, take appropriate measures to eliminate noise. MITSUBISHI A/QnA Series A6GPP, A7PHP, personal computer, etc.
2 - 18 2 MITSUBISHI PC • 3 4 MITSUBISHI PC • 3 (QnH series CPU port) Connection Connect to the QnH series CPU port. The communication parameter setting of ZM-** is done automatically. Available PC ZM-71SE Model Setting CPU QnHCPU port(A) Q06H-A QnHCPU port(Q) Q02 Q02H Q06H Wiring Diagram (refer to P2-19) RS-232C exclusive cable (order product) When the CPU is updated, or the specifications are changed, there is some possibility that ZM** cannot be connected to the PLC.
2 MITSUBISHI PC • 3 2 - 19 Available Memory Available: Memory Bit Write TYPE D (data register) W (link register) 1 R (file register) 2 TN (timer/current value) 3 CN (counter/current value) 4 5 M (internal relay) 6 L (latch relay) 7 B (link relay) 8 X (input relay) Y (output relay) 10 TS (timer/contact) 11 TC (timer/coil) 12 CS (counter/contact) 13 SD (special register) Remarks 0 SPU (special unit) CC (counter/coil) Unit No.
2 - 20 2 MITSUBISHI PC • 4 5 MITSUBISHI PC • 4 (FX1/2 series) Connection Connect to the FX series CPU port. The communication parameter setting of ZM-** is done automatically.
2 MITSUBISHI PC • 4 2 - 21 Notes on the direct connection with the CPU port of FX series CPU Note According to our noise tests, the attachment of a ferrite core improves noise voltage by 650 to 900V and aids in preventing communication errors. For safer operation, be sure to attach the ferrite core to the cable. Take appropriate measures to eliminate any noise from entering the communication cable between the ZM-** and MITSUBISHI FX series CPU.
2 - 22 2 MITSUBISHI PC • 4 FX series CPU A6GPP, A7PHP, personal computer, etc. MELSEC FX2-24MT TRANSISTOR UNIT POWER RUN BATT.V V-M DD G P P 123 GD In case of direct connection with the CPU port of FX1/2 series, use the exclusive cable(order product). Exclusive cable (order product) Slide switch 1 ----- A series 2 ----- Q series 3 ----- FX series * Set this switch before plugging in the ZM-1MD2. ZM-** Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC.
2 MITSUBISHI PC • 5 6 2 - 23 MITSUBISHI PC • 5 (FX2N/0N A protocol) Available PC ZM-71SE Model Setting PC FX2N FX series (A protocol) FX0N Link Unit Wiring Diagram(refer to P2-25) FX2N-232-BD RS-232C [Wiring Diagram 1] FX2N-485-BD RS-485 [Wiring Diagram 3] FX2N-422-BD RS-422 exclusive cable (order product) FX0N-232ADP RS-232C [Wiring Diagram 2] FX0N-485ADP RS-485 [Wiring Diagram 3] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows:
2 - 24 2 MITSUBISHI PC • 5 Available Memory Available: Memory Bit Write TYPE D (data register) 0 TN (timer/current value) 1 Unavailable: Remarks CN (counter/current value) 2 32CN (counter 32bits) 3 *1 M (internal relay) 4 *2 S (state) 5 X (input relay) 6 Y (output relay) 7 TS (timer/contact) 8 CS (counter/contact) 9 Read only *1 The meaning of CN200~CN255 is the same as the meaning of 32CN(counter 32bits). *2 In case of the items which can display double word data (e.
2 - 25 2 MITSUBISHI PC • 5 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 RD 2 RD 3 SD 3 RS 4 SG 5 CS 5 SG 7 D-sub 9pin(Female: ) * Use twist shielded cables. Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 SG 7 CS 5 SG 7 D-sub 25pin(Male: * Use twist shielded cables.
2 - 26 2 MITSUBISHI PC • 6 7 MITSUBISHI PC • 6 (FX2N series) Connection Connect to the FX series CPU port. The communication parameter setting of ZM-** is done automatically. Available PC ZM-71SE Model Setting CPC FX2N series FX2N Wiring Diagram RS-422 exclusive cable (order product) When the CPU is updated, or the specifications are changed, there is some possibility that ZM-** cannot be connected to the PC.
2 MITSUBISHI PC • 7 8 2 - 27 MITSUBISHI PC • 7 (Net 10) ZM-** can access other CPUs on the NET II(/B) or NET/10 when ZM-** is connected to one of the link units that the data link system or network system consists of. Select “Net10” as PC setting when configuring the screen data on the panel editor. To access other CPU on the NET II (/B) or NET/10 from ZM-**. • In case of NET II(/B), only the network which has the CPU with the link unit connected to the ZM-** (e.g. No. 1) can be accessed.
2 - 28 2 MITSUBISHI PC • 7 Macro type to specify network • • • • • • • • • • • • • • • • • • • • • • • • • • • • [OUT_ENQ] command of [SYS] F1 Memory n+0 0 (fixed) n+1 Specify network: 2 (fixed) n+2 System code n+3 Network No. The addresses n+0 and n+1 are fixed for 0 and 2. Specify n+2 [System code] to 1: NET/10 2: NET II(/B) Enter "0" to n+3 [Network No.] when n+2 [System code] indicates "2", and "the number to be accessed" to n+3 [Network No.] when n+2 [System code] indicates "1".
2 OMRON PC• 1 9 2 - 29 OMRON PC • 1 Available PC ZM-71SE Model Setting PC C20H, C28H, C40H C120, C120F C200H C500, C500F C1000H C2000, C2000H C200H C200HS-CPU01,03 C200HS-CPU21,23 C200HS-CPU31,33 Link Unit Wiring Diagram (refer to P2-28, 29) CPU unit with a built-in RS-232C port (host link port) RS-232C [Wiring Diagram 1] C120-LK201-V1 RS-232C [Wiring Diagram 3] C120-LK202-V1 RS-422 [Wiring Diagram 4] C200H-LK201 C200H-LK201-V1 C200H-LK202 C200H-LK202-V1 RS-232C [Wiring Diagram 3] RS-422 [Wi
2 - 30 2 OMRON PC• 1 Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 OMRON PC• 1 2 - 31 Available Memory Available: C Memory Bit Write TYPE DM (data memory) 0 CH (input/output relay) 1 HR (holding relay) 2 LR (latch relay) 3 AR (alarm relay) 4 T (timer/current value) 5 C (counter/current value) 6 Remarks TU (timer [contact]) 9 Read only CU (counter [contact]) 10 Read only CV Available: Memory Bit Write TYPE DM (data memory) 0 CH (input/output relay) 1 AR (alarm relay) 4 T (timer/current value) 5 C (counter/current value) 6
2 - 32 2 OMRON PC• 1 Set the memory to the extent of the memory range of each PC model. In case of using the [Bit Write] memory as the bit device of the [Output Action] is [Momentary W], the other bits will be cleared when the bit memory is output, because the [Bit Write] will be output by one word (refer to P5-10, reference 14-7 of ZM-71SE Instruction Manual). Use [TYPE] number to assign indirect memory for macro programs.
2 OMRON PC• 1 RS-422 Wiring Diagram 4 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SG 7 RDB 1 +SD 12 SG 3 -SD 13 SDB 5 +RD 24 RDA 6 -RD 25 SDA 9 D-sub 9pin(Male: ) * Use twist shielded cables. Wiring Diagram 5 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SG 7 SG 9 +SD 12 RDB 8 D-sub 9pin(Male: -SD 13 RDA 6 +RD 24 SDB 2 -RD 25 SDA 1 ) * Use twist shielded cables.
2 - 34 2 OMRON PC• 2 10 OMRON PC • 2 (OMRON-CS1 DNA) When connect the ZM-** to CS1 on a network, the ZM-** can also access the other CS1 on a network. CS1 (2-2) CS1 (1-2) Network No.1 CS1 (1-3) (2-1) CS1 (1-1) Network No.
2 HITACHI PC • 1 11 2 - 35 HITACHI PC • 1 (HIDIC H series) Available PC ZM-71SE Model Setting PC HIDIC H series CPU HIDIC-H * Link Unit Wiring Diagram(refer to P2-37) COMM-2H RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 2] PERIPHERAL port on a CPU module RS-232C [Wiring Diagram 1] EH150 * [EH-RS05] cable made by HITACHI + RS-232C [Wiring Diagram 1] H-252C on a CPU module PERIPHERAL 1 RS-232C [Wiring Diagram 1] PERIPHERAL 2 * [CNCOM-05] cable made by HITACHI + RS-232C [Wiring Diagram 1
2 - 36 2 HITACHI PC • 1 Switch Setting Baud rate MODE switch : 19200bps : To connect to both RS-232C and RS-422, set MODE switch to 9. RS-232C(pattern 2, w/o) RS-422(pattern 2, with port) ST No. switch : Choose "0" for both X10 and X1.
2 HITACHI PC • 1 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 CS 5 RS 4 SG 7 CS 5 DR 7 PHL 8 SG 9 PV12 14 D-sub 15pin(Male: * Use twist shielded cables. RS-422 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC +SD 12 TxDP -SD 13 TxDN +RD 24 RxDP -RD 25 RxDN * Use twist shielded cables.
2 - 38 2 HITACHI PC • 2 12 HITACHI PC • 2 (HIDIC-S10α) Available PC Host Link H-7338 ZM-71SE Model Setting Wiring Diagram (refer to P2-39,40) PC Link Unit S10 2alpha Port on a CPU unit RS-422 [Wiring Diagram 3] RS-232C [Wiring Diagram 1] HIDIC-S10/2alpha S10 min RS-232C [Wiring Diagram 2] HIDIC-S10/ABS ABS* 1 RS-422 [Wiring Diagram 3] *1 Specify the memory by absolute addresses. For further information, refer to the relevant PC manual.
2 HITACHI PC • 2 Memory Bit Write CS (up/down counter set value) TYPE 2 - 39 Remarks 13 CC (up/down counter elapsed value) 14 DW (data register) 15 E (internal relay) 16 EW as word device S (global link) 17 SW as word device J (keep relay) 18 JW as word device Q (on-delay timer contact) 19 QW as word device M (one shot timer contact) 20 MW as word device HIDIC ABS Available: Memory Bit Write TYPE 0E 0 06 1 18 2 19 3 1A 4 1B 5 1C 6 1D 7 Unavailable: Remarks
2 - 40 2 HITACHI PC • 2 Wiring Diagram 2 PC ZM-** (CN1) D-sub 25pin(Male: D-sub 9pin(Female: ) FG 1 CD 1 SD 2 RD 2 RD 3 SD 3 RS 4 ER 4 CS 5 SG 5 SG 7 DR 6 RS 7 CS 8 ) * Use twist shielded cables. RS-422 Wiring Diagram 3 For connection to the S10 ×α series, use a 50 Ω(1/2W) resistance as shown below. ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC +SD 12 UTX H -SD 13 UTX L +RD 24 50 URX H -RD 25 50 URX L * Use twist shielded cables.
2 Matsushita PC 13 2 - 41 Matsushita PC Available PC ZM-71SE Mode Setting MEWNET PC Link Unit Wiring Diagram (refer to P2-43) FP1 RS-232C port on a CPU unit RS-232C [Wiring Diagram 1] FP3 AFP3462 RS-232C [Wiring Diagram 1] AFP3463 RS-422 [Wiring Diagram 4] FP5 AFP5462 RS-232C [Wiring Diagram 1] RS-232C [Wiring Diagram 1] FP10 RS-232C port on a CPU unit AFP5462 RS-232C [Wiring Diagram 1] RS-232C port on a CPU unit RS-232C [Wiring Diagram 1] AFP3462 AFP3463 RS-232C [Wiring Diagram 1]
2 - 42 2 Matsushita PC Switch Setting of Link Unit No Setting 1 ON 2 OFF 3 OFF 4 OFF Data length 7 5 ON Parity provided 6 ON Even 7 OFF Stop bit 1 8 OFF CS, CD invalid Contents Same as ZM-** (normally 19200bps) Available Memory Available: Memory Bit Write TYPE Unavailable: Remarks DT (data register) 0 X (external input relay) 1 WX as word device, read only Y (external output relay) 2 WY as word device R (internal relay) 3 WR as word device, special relay includ
2 Matsushita PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 SG 7 D-sub 9pin(Male: ) 2 CD 8 ER 9 * Use twist shielded cables. Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SD 2 SD RD 3 RD RS 4 SG CS 5 SG 7 * Use twist shielded cables.
2 - 44 14 2 YOKOGAWA PC • 1 YOKOGAWA PC • 1 (FA-500) Available PC Panel Editing software models for setting Wiring Diagram (refer to P2-39) Link Unit PC RS-232C [Wiring Diagram 1] LC01-0N FA500 FA500 RS-232C [Wiring Diagram 1] LC02-0N RS-422 [Wiring Diagram 2] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 YOKOGAWA PC • 1 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 DR 6 SG 7 ER 20 D-sub 25pin(Male: * Use twist shielded cables. RS-422 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 RDB +SD 12 RDA -SD 13 SDB +RD 24 SDA -RD 25 SG * Use twist shielded cables.
2 - 46 2 YOKOGAWA PC • 2 15 YOKOGAWA PC • 2 (FA-M3) Available PC ZM-71SE Model Setting FA-M3 FA-M3R PC FA-M3 FA-M3 R Link Unit Wiring Diagram (refer to P2-48) Programming tool port *1 on a CPU module Cable made by YOKOGAWA [KM11-2N] F3LC01-1N*2 RS-232C [Wiring Diagram 1] F3LC11-1N RS-232C [Wiring Diagram 1] F3LC11-2N RS-422 [Wiring Diagram 2] Programming tool port on a CPU module Cable made by YOKOGAWA [KM11-2N] *1 CPU types which can be connected directly to programming tool port on a
2 YOKOGAWA PC • 2 2 - 47 Available Memory Available: Memory * Bit Write TYPE D (data register) 0 R (common register) 1 V (index register) 2 W (link register) 3 Z (special register) 4 TP (down timer current value) 5 TS (timer set value) 6 CP (down counter current value) 7 CS (down counter set value) 8 X (input relay) Y (output relay) 10 I (internal relay) 11 E (common relay) 12 L (link relay) 13 M (special relay) 14 B (file register) 15 Unavailable: Rem
2 - 48 2 YOKOGAWA PC • 2 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 RD 2 RD 3 SD 3 RS 4 ER 4 CS 5 SG 5 SG 7 DR 6 RS 7 CS 8 D-sub 9pin(Male: * Use twist shielded cables. RS-422 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 RDB +SD 12 RDA -SD 13 SDB +RD 24 SDA -RD 25 SG * Use twist shielded cables.
2 YASKAWA PC • 1 16 2 - 49 YASKAWA PC• 1 Available PC ZM-71SE Model Setting PC Wiring Diagram (refer to P2-50, 51) Link Unit GL60 series JAMSC-IF60 JAMSC-IF61 JAMSC-IF611 RS-232C [Wiring Diagram 1] JAMSC-IF612 JAMSC-IF613 RS-422 [Wiring Diagram 3] Memobus port on a CPU module RS-232C [Wiring Diagram 1] JAMSC -120NOM27100 RS-422 [Wiring Diagram 4] PORT2 on a CPU unit RS-232C [Wiring Diagram 2] Memobus GL120, GL130 series PROGIC-8 * Other kinds of MEMOBUS unit can be connected.
2 - 50 2 YASKAWA PC • 1 Available Memory Available: Memory Bit Write TYPE 4 (word device) 0 3 (input register) 1 R (link register) 2 A (extension register) 3 0 (coil) 4 D (link coil) 5 1 (input register) 6 7 (constant register) 7 Unavailable: Remarks Constant register included Set the memory to the extent of the memory range of each PC model.
2 - 51 2 YASKAWA PC Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 TXD 2 RD 3 RXD 3 RS 4 RTS 4 CS 5 CTS 5 SG 7 DSR 6 GND 7 DTR 9 D-sub 15pin(Male: ) * Use twist shielded cables. RS-422 Wiring Diagram 3 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SG 7 TXD+ 2 +SD 12 RXD+ 3 -SD 13 RXD- 6 +RD 24 SG 7 -RD 25 TXD- 9 D-sub 9pin(Male: ) * Use twist shielded cables.
2 - 52 2 YASKAWA PC • 2 17 YASKAWA PC• 2 Available PLC ZM-71SE Model Setting PLC CP9200SH Wiring Diagram (refer to P2-53) Link Unit RS-232C [Wiring Diagram 1] [Wiring Diagram 2] CP217IF RS-422 CP9200SH /MP900 MP920 MP930 [Wiring Diagram 3] Memobus port on a CPU module RS-232C [Wiring Diagram 1] 217IF RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 4] CommunicationSetting The recommended communication parameter setting of both PLC and ZM-** is as follows: Item Setting of PLC Comm.
2 YASKAWA PC • 2 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: CP217IF(CN1) 217IF(CN1/2) ) FG 1 SD 2 TXD 2 RD 3 RXD 3 RS 4 RTS 4 CS 5 CTS 5 SG 7 D-sub 9pin(Male: DSR 6 SGND 7 DTR 9 ) * Use twist shielded cables.
2 - 54 2 TOYOPUC PC 18 TOYOPUC PC Available PC ZM-71SE Model Setting PC Link Unit TOYOPUC-L2/PC2 etc. TOYOPUC CMP-LINK Wiring Diagram (refer to P2-56) RS-422 [Wiring Diagram 1] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm. Parameter of ZM-** Baud Rate 19200bps 19200bps Port 0 0 Parity Even Even Transmission Data Length Code Stop Bit 7 (ASC II) 7 2 2 Set the [Trans.
2 TOYOPUC PC 2 - 55 Available Memory Available: Memory Bit Write TYPE Remarks D (data register) R (link register) 1 B (file register) 2 N (current value register) 3 X (input relay) 4 WX as word device Y (output relay) 5 WY as word device M (internal relay) 6 WM as word device K (keep relay) 7 WK as word device L (link relay) 8 WL as word device T (counter/contact) 9 WT as word device C (counter/contact) 10 WC as word device 0 11 U (expansion data register)
2 - 56 2 TOYOPUC PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-422 Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 + +SD 12 - -SD 13 0V +RD 24 -RD 25 * Use twist shielded cables. Screen Editing (Memory Input) If [Split Data Area] is selected at the [Trans. Mode], the [PRG No] setting is available at the [Memory Input] dialog.
2 FUJI PC • 1 19 2 - 57 FUJI PC • 1 (MICREX-F series) Available PC ZM-71SE Model Setting PC Link Unit F55 F70, F70S MICREX-F Series (MICREX-F series ZM70) F80H, F120H, F120S F140S, F15□S Wiring Diagram (refer to P2-59) NV1L-RS2 RS-232C [Wiring Diagram 1] NC1L-RS2 RS-232C [Wiring Diagram 1] NC1L-RS4 RS-485 [Wiring Diagram 2] FFU120B FFK120A RS-232C [Wiring Diagram 1] RS-485 [Wiring Diagram 2] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as f
2 - 58 2 FUJI PC • 1 Available Memory Available: Memory Bit Write TYPE Unavailable: Remarks M (auxiliary relay) 0 K (keep relay) 1 WK as word device B (input/output relay) 2 WB as word device L (link relay) 9 WL as word device WF (special relay) 10 TS (timer/set value) 11 TR (timer/current value) WM as word device *1 12 *1 W9 (timer/current value 0.
2 FUJI PC • 1 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 DR 6 SG 7 CD 8 D-sub 25pin(Male: * Use twist shielded cables. RS-485 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 SDA +SD 12 SDB -SD 13 RDA +RD 24 RDB -RD 25 SG * Use twist shielded cables.
2 - 60 2 FUJI PC • 2 20 FUJI PC • 2 (FLEX-PC series) Available PC ZM-71SE Panel Setting *1 FLEX-PC Series PC Wiring Diagram (refer to P2-62) Link Unit NS-T NJ-T NJRS-1 RS-232C [Wiring Diagram 1] NJRS-2 RS-232C [Wiring Diagram 1] NJRS-4 RS-485 [Wiring Diagram 2] *1 When FLEX-PC TOYOTA version is used, select "FLEX-PC(T)" in [PC Type]. Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 FUJI PC • 2 2 - 61 Switch Setting MODE Switch: RS-232C: 1 RS-485: 3 RS-485 Port Setting SW: "0" for both × 10, × 1 RS-485 Termination resistance: ON Character Switches No Setting Contents 8 ON Switch setting 7 ON Parity provided 6 ON Even 5 ON 7 bit 4 ON 1 bit 3 ON 2 ON 1 OFF Same as ZM-** (normally 19200bps) Available Memory Available: Standard Memory TOYOTA Ver.
2 - 62 2 FUJI PC • 2 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 DR 6 SG 7 CD 8 D-sub 25pin(Male: * Use twist shielded cables. RS-485 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 SDA +SD 12 SDB -SD 13 RDA +RD 24 RDB -RD 25 SG * Use twist shielded cables.
2 FUJI PC • 3 21 2 - 63 FUJI PC • 3 (FLEX-PC CPU port) Available PC ZM-71SE Panel Setting *1 FLEX-PC CPU PC Wiring Diagram (refer to P2-64) FLEX-PC CPU RS-485 [FU-CPUNS] made by Sharp NJ-B16 CPU RS-232C [Wiring Diagram 1] *1 When FLEX-PC CPU TOYOTA version is used, select "FLEX-PC CPU(T)" in [PC Type]. Communication Setting Connect to the CPU port. The communication parameter setting of ZM-** is done automatically. Available Memory Available: Standard Memory TOYOTA Ver.
2 - 64 2 FUJI PC • 3 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) NJ-B16 FG 1 SD 2 RD 2 RD 3 SD 3 RS 4 CTS 4 CS 5 RTS 5 SG 7 SG 7 D-sub 15pin(Male: * Use twist shielded cables. RS-485 Use the exclusive cable (order product) for RS-485 communications.
2 FUJI PC • 4 22 2 - 65 FUJI PC • 4 (TOYOTA version NJ Computer Link) Available PC ZM-71SE Model Setting FLEX-PC COM Wiring Diagram (refer to P2-66) PC Computer link of FLEX-PC NJ-JM RS-422 [Wiring Diagram 1] Connect to the terminal block of the FLEX-PC NJ-JM computer link. For further information, refer to the FUJI's PC manual. Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 - 66 2 FUJI PC • 4 Available Memory Available: Memory Bit Write TYPE Unavailable: Remarks D (data register) 0 R (link register) 1 M (internal relay) 2 K (latch relay) 3 WK as word device X (input relay) 4 WX as word device Y (output relay) 5 WY as word device WM as word device W (file register) 6 TN (timer/current value) 7 Read only 8 Read only CN (counter/current value) T (timer/contact) C (counter/contact) 10 9 ZV (special register) 12 V (special relay)
2 Koyo PC 23 2 - 67 Koyo PC Available PC ZM-71SE Mode Setting PC Wiring Diagram (refer to P2-70, 71) Link Unit SU-5 U01-DM RS-232C [Wiring Diagram 1] SU-6B Port on a CPU unit RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 3] G01-DM RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 4] Port on a CPU unit RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 4] SG-8 SU/SG SR-T SR-T (K prt) RS-232C program transfer cable made by Koyo [S-15JP] + Convert connector cable made by Koyo [S-15CNJ]
2 - 68 2 Koyo PC Available Memory SU/SG Available: Memory Bit Write TYPE R (data register) I (input relay) 1 Q (output relay) 2 M (internal relay) 3 S (stage) 4 GI (global inputs) 5 Unavailable: Remarks 0 GQ (global outputs) 6 T (timer/contact) 7 C (counter/contact) 8 SR-1T/6T (TOYOTA version) Available: Memory Bit Write TYPE Unavailable: Remarks D (data register) 0 X (input relay) 1 X/Y common use Y (output relay) 2 X/Y common use M (internal relay) 3
2 Koyo PC Switch Setting U-01DM On-line/off-line switch: on-line UNIT ADR switch: “0” for x10, “1” for x1 SW4 Dip Switch: No Setting 1 ON 2 ON 3 ON Contents Same as ZM-** (normally 19200bps) 4 ON Parity provided 5 OFF Self-diagnosis 6 OFF 7 OFF 8 OFF Response delay time 0msec SW5 Dip Switch: No Setting Contents 1 OFF Master/slave control 2 OFF Slave 3 OFF Communication time-out 4 OFF HEX mode G-01DM On-line/off-line switch: on-line Short plug 1: open Short plug 2 RS-232
2 - 70 2 Koyo PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-*2 to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 SG 7 D-sub 25pin(Male: ) * Use twist shielded cables. Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 TXD 2 RD 3 RXD 3 RS 4 RTS 4 CS 5 CTS 5 SG 7 0V 7 D-sub 15pin(Male: ) * Use twist shielded cables.
2 Koyo PC Wiring Diagram 4 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SG 7 0V 7 +SD 12 +OUT 14 -SD 13 -OUT 15 +RD 24 -IN 16 -RD 25 +IN 17 D-sub 25pin(Male: * Use twist shielded cables. Wiring Diagram 5 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 FG +SD 12 T1 -SD 13 T2 +RD 24 T3 -RD 25 * Use twist shielded cables.
2 - 72 24 2 Allen-Bradley PC • 1 Allen-Bradley PC • 1 (PLC-5 series) Available PC ZM-71SE Model Setting PLC-5 PC Link Unit Wiring Diagram (refer to P2-76) 1785-KE RS-232C [Wiring Diagram 1] 1770-KF2 RS-232C [Wiring Diagram 2] RS-422 [Wiring Diagram 3] PLC-5 Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 Allen-Bradley PC • 1 2 - 73 Available Memory Available: Memory N (integer) B (bit) Bit Write TYPE Remarks 0 1 T.ACC (timer [current value]) 2 T.PRE (timer [setting value]) 3 C.ACC (counter [current value]) 4 C.PRE (counter [setting value]) 5 I (input) 6 O (output) 7 S (status) 8 T (timer [contol]) Unavailable: 9 C (counter [control]) 10 R (control [control]) 11 R.LEN (control [data length]) 12 R.
2 - 74 2 Allen-Bradley PC • 1 SwitchSetting U-01DM SW1 (protocol) No Setting 1 ON Contents 2 OFF 3 OFF 4 ON Duplicate message unacceptable 5 OFF Handshaking signal ignored 6 ON Diagnosis execution BCC, Even, no SW2 (port) Specify the port for 1785-KE. (This port should not be duplicated in the network.
2 Allen-Bradley PC • 1 1770-KF2 SW1 (protocol) No Setting Contents 1 ON Protocol 2 OFF Protocol 3 ON Duplicated message unacceptable 4 OFF Handshaking signal ignored 5 OFF Protocol SW2, SW3, SW4 (port) Specify the port for 1770-KF2. (This port should not be duplicated in the network.) SW3 (network link transmission speed) Adjust the setting according to the network you are using. SW6 (asynchronous link transmission speed) Set the same speed as ZM-**.
2 - 76 2 Allen-Bradley PC • 1 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: FG 1 ) PC D-sub 15pin(Male: SD 2 TXD 2 RD 3 RXD 3 RS 4 RTS 4 CS 5 CTS 5 SG 7 DSR 6 SG 7 DCD 8 DTR 11 SG 13 ) * Use twist shielded cables.
2 Allen-Bradley PC • 2 25 2 - 77 Allen-Bradley PC • 2 (SLC500 series/ Micro Logix 1000) Available PC ZM-71SE Model Setting PC SLC500 SLC 5/03 or later models Micro Logix 1000 Micro Logix 1000 Link Unit Wiring Diagram (refer to P2-79,80) CPU (Processor module) RS-232C channel RS-232C [Wiring Diagram 1] 1747-KE RS-232C [Wiring Diagram 2] RS-422 [Wiring Diagram 4] Port on a CPU unit *RS-232C program transfer cable made by A-B +RS-232C [Wiring Diagram 3] * When using RS-232C program transfer c
2 - 78 2 Allen-Bradley PC • 2 Available Memory Available: Memory Bit Write TYPE N (integer) 0 B (bit) 1 T.ACC (timer [current value]) Remarks 2 T.PRE (timer [setting value]) 3 C.ACC (counter [current value]) 4 C.PRE (counter [setting value]) 5 I (input) 6 O (output) 7 S (status) 8 T (timer [control]) 9 C (counter [control]) 10 R (control [control]) 11 R.LEN (control [data length]) Unavailable: 12 R.
2 Allen-Bradley PC • 2 1747-KE Set up the parameters for 1747-KE, using the software specifically designed for this purpose.
2 - 80 2 Allen-Bradley PC • 2 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 RXD 2 RD 3 TXD 3 RS 4 DTR 4 CS 5 COM 5 SG 7 DSR 6 RTS 7 CTS 8 D-sub 9pin(Female: ) * Use twist shielded cables. Wiring Diagram 3 PC ZM-** (CN1) D-sub 25pin(Male: D-sub 9pin(Male: ) FG 1 CD 1 SD 2 RD 2 RD 3 SD 3 RS 4 RS 4 CS 5 GND 5 SG 7 DR 6 RS 7 CS 8 . * Use twist shielded cables.
2 GE Fanuc PC • 1 26 2 - 81 GE Fanuc PC • 1 (90 series) Available PC ZM-71SE Model Setting 90 Series PC Wiring Diagram (refer to P2-82) Link Unit Programmable co-processor (PCM) Series 90-30 RS-485 [Wiring Diagram 1] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Setting of PC Comm.
2 - 82 2 GE Fanuc PC • 1 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 GND 7 D-sub 25pin(Male: ) * Use twist shielded cables.
2 GE Fanuc PC • 2 27 2 - 83 GE Fanuc PC • 2 (90 series SNP-X) Available PC ZM-71SE Model Setting 90 Series (SNP-X) Wiring Diagram (refer to P2-84) PC Series 90 micro (CPU port) Series 90-30 (CPU port) RS-485 [Wiring Diagram 1] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 - 84 2 GE Fanuc PC • 2 Set the memory to the extent of the memory range of each PC model. In case of using the [Bit Write] memory as the bit device of the [Output Action] is [Momentary W], the other bits will be cleared when the bit memory is output, because the [Bit Write] will be output by one word (refer to P5-10, reference 14-7 of ZM-71SE Instruction Manual). Use [TYPE] number to assign indirect memory for macro programs.
2 TOSHIBA PC 28 2 - 85 TOSHIBA PC (T series) Available PC ZM-71SE Model Setting T Series PC Wiring Diagram (refer to P2-86) RS-422 [Wiring Diagram 1] T series Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows. For further information, refer to the TOSHIBA’s PC manual. Item Setting of PC Comm.
2 - 86 2 TOSHIBA PC Available Memory Available: Memory Bit Write TYPE D (data register) 0 X (input register) 1 Unavailable: Remarks XW as word device Y (output register) 2 YW as word device R (auxiliary relay) 5 RW as word device L (link relay) 6 LW as word device W (link register) 7 F (file register) 8 TN (timer/current value) 9 Read only CN (counter/current value) 10 Read only TS (timer/contact) 11 Read only CS (counter/contact) 12 Read only Set the memory to
2 TOSHIBA MACHINE PC 29 2 - 87 TOSHIBA MACHINE PC (TC200) Available PC ZM-71SE Model Setting PC Wiring Diagram (refer to P2-88) Link Unit Port on a CPU unit TC200 TC200 RS-232C [Wiring Diagram 1] TCCMW TCCMO Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows. Item Setting of PC Comm.
2 - 88 2 TOSHIBA MACHINE PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 TXD 2 RD 3 RXD 3 RS 4 DTR 4 CS 5 GND 5 SG 7 DSR 6 CTS 7 RTS 8 D-sub 9pin(Female: * Use twist shielded cables.
2 SIEMENS PC • 1 30 2 - 89 SIEMENS PC • 1 (S5-90, S5-95U, S5-100U) Available PC A similar program as RK512 is required. ZM-71SE Model Setting S5/S7 Link Unit Wiring Diagram (refer to P2-90) S5-90U S5-95U S5-100U CP-512SI (3964R Transmission Protocol) RS-232C [Wiring Diagram 1] S5-95U Second serial interface (3964R Transmission Protocol) RS-232C [Wiring Diagram 2] PC *1 *1 With the S5-95U second interface, the SIEMENS’s converter 6ES5 734-1BD20 must be used.
2 - 90 2 SIEMENS PC • 1 Set the memory to the extent of the memory range of each PC model. In case of using the [Bit Write] memory as the bit device of the [Output Action] is [Momentary W], the other bits will be cleared when the bit memory is output, because the [Bit Write] will be output by one word (refer to P5-10, reference 14-7 of ZM-71SE Instruction Manual). Use [TYPE] number to assign indirect memory for macro programs.
2 SIEMENS PC • 2 31 2 - 91 SIEMENS PC • 2 (S5-115U, S5-135U, S5-155U) Available PC ZM-71SE Model Setting S5/S7 PC Wiring Diagram (refer to P2-92) Link Unit S5-115U S5-135U S5-155U CP-524(3964R/RK512) S7-300 CP-341(3964R/RK512) S7-400 CP-441(3964R/RK512) CP-544(3964R/RK512) RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 2] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Baud Rate 9600bps Comm.
2 - 92 2 SIEMENS PC • 2 * Notes on converting the data file of ZM-41/70 (or ZM-30) into the ZM-** data file. When converting the data file of ZM-41/70 (or ZM-30) into the ZM-** data file, the PLC type is automatically selected as "SIEMENS S5 ZM-70." In ZM-41/70 (or ZM-30), the order of bytes in I (input relay), Q (output relay) and F (internal relay) is reversed.
2 SIEMENS PC • 3 32 2 - 93 SIEMENS PC • 3 (S5 PG port) Connection Connect to the S5 series PG port. The communication parameter setting of ZM-** is done automatically.
2 - 94 2 SIEMENS PC • 3 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: PC-Converter cable (6ES5 734-1BD20) ) FG 1 SD 2 TXD 2 RD 3 RXD 3 RS 4 DTR 4 CS 5 GND 5 SG 7 CTS 7 D-sub 25pin(Male: * Use twist shielded cables.
2 SIEMENS PC • 4 33 2 - 95 SIEMENS PC • 4 (S7-200 PPI) Available PLC ZM-71SE Model Setting S7-200 PPI Wiring Diagram (refer to P2-96) PC RS-422 [Wiring Diagram 1] S7-200 series CommunicationSetting The recommended communication parameter setting of both PLC and ZM-** is as follows: Item Setting of PC Comm.
2 - 96 2 SIEMENS PC • 4 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-422 Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SG 7 SG 5 +SD 12 TxD/RxD 3 -SD 13 TxD/RxD 8 +RD 24 -RD 25 D-sub 9pin(Male: * Use twist shielded cables. SettingofTerminalResistance Set the dip switch S1 of ZM-** series to OFF. Connect terminal registance to the ZM-** serial connector (CN1) as follows.
2 SIEMENS PC • 5 34 2 - 97 SIEMENS PC • 5 (TI545, 555) Available PC ZM-71SE Model Setting TI500/505 Wiring Diagram (refer to P2-98) PC TI545/555 CPU port (built-in) RS-232C [Wiring Diagram 1] Communication Setting Connect the cable to the CPU port (RS-232C built-in port) for TI545/555. The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 - 98 2 SIEMENS PC • 3 *1 In case of using DCP (drum count/set value), set the drum step No.1 to 16. The assigned memory is indicated while editing the screen as illustrated: DCP30000 : 1 Drum step No. Colon Address No. Set the memory to the extent of the memory range of each PC model.
2 Shinko PC 35 2 - 99 Shinko PC Available PC ZM-71SE Model Setting PC SELMART SELMART-100 or later series Wiring Diagram (refer to P2-100) Link Unit Version O1M2-UCI-6X RS-232C [Wiring Diagram 1] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 - 100 2 Shinko PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 SG 7 D-sub 25pin(Male: * Use twist shielded cables.
2 SAMSUNG PC 36 2 - 101 SAMSUNG PC (SPC series) Available PC ZM-71SE Model Setting SPC Series Wiring Diagram (refer to P2-102) PC RS-232C [Wiring Diagram 1] SPC series RS-422/485 [Wiring Diagram 2] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 - 102 2 SAMSUNG PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 TXD 2 RD 3 RXD 3 RS 4 GND 5 CS 5 SG 7 D-sub 9pin(Male: ) * Use twist shielded cables. RS-422 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 +SD 12 TR- 6 -SD 13 TR+ 7 +RD 24 -RD 25 D-sub 9pin(Male: * Use twist shielded cables.
2 KEYENCE PC• 1 37 2 - 103 KEYENCE PC • 1 (KZ series) Available PC ZM-71SE Model Setting KZ Series PC Wiring Diagram (refer to P2-104) Link Unit KZ300 KZ-L2 Port 1 RS-232C [Wiring Diagram 1] Port 2 RS-232C [Wiring Diagram 2] RS-422 [Wiring Diagram 3] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: For further information, refer to the communication specifications of KEYENCE link unit. Item Setting of PC Comm.
2 - 104 2 KEYENCE PC• 1 Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 SG 7 D-sub 25pin(Male: * Use twist shielded cables. Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SD 2 SD RD 3 RD SG 7 SG * Use twist shielded cables.
2 KEYENCE PC• 2 38 2 - 105 KEYENCE PC • 2 (KZ-A500) Available PLC ZM-71SE Model Setting PLC KZ-A500 CPU Port Link Unit CPU Modular Port RS-232C [Wiring Diagram 1] RS-422 Cable made by KEYENCE [KZ-C20] + Cable made by Hakko [MB-CPUQ] KZ-L10 Port 1 RS-232C [Wiring Diagram 2] Port 2 RS-232C [Wiring Diagram 3] RS-422 [Wiring Diagram 4] KZ-A500 MITSUBISHI AnA/N/U series Wiring Diagram (refer to P2-106,107) CommunicationSetting The recommended communication parameter setting of both PC and ZM-** is
2 - 106 2 KEYENCE PC• 2 Available Memory Available: Memory Bit Write TYPE D (data register) 0 W (link register) 1 R (file register) 2 TN (timer/current value) Remarks 3 CN (counter/current value) 4 M (internal relay) 6 L (latch relay) 7 B (link relay) 8 X (input relay) 9 Y (output relay) 10 TS (timer/contact) 11 TC (timer/coil) 12 CS (counter/contact) 13 CC (counter/coil) Unavailable: 14 Set the memory to the extent of the memory range of each PC model.
2 - 107 Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 DR 6 SG 7 CD 8 D-sub 25pin(Male: * Use twist shielded cables. Wiring Diagram 3 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SD 2 SD RD 3 RD RS 4 SG CS 5 SG 7 * Use twist shielded cables. RS-422 Wiring Diagram 4 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 PC SG 7 SDB +SD 12 SDA -SD 13 RDB +RD 24 RDA -RD 25 SG * Use twist shielded cables.
2 - 108 39 KEYENCE PC • 3 (KV series) Available PLC ZM-71SE Model Setting Wiring Diagram (refer to P2-109) PC KZ-10,16,24,40,80,300,350 (Program port direct connection) KV series (Program port direct connection) KV Series KZ 24/300 Series CPU KZ-24,300 (Program port direct connection) KV 10/24 Series CPU KZ-V10,24 (Program port direct connection) RS-232C [Wiring diagram 1] or Cable made by KEYENCE [OP-26487] + connecter [OP26485] RS-422 Cable made by KEYENCE [KZ-C20] + Cable made by Hakko [MB-CPU
2 - 109 Available Memory Available: Memory Bit Write TYPE DM (data memory) 0 CH (input/output relay) 1 T (timer/current value) 2 C (counter/current value) 3 TS (timer/set value) 4 CS (counter/set value) 5 TU (timer/contact) Unavailable: Remarks 6 Read only CU (counter/contact) 7 Read only TM (temporary data memory) 8 Set the memory to the extent of the memory range of each PC model.
2 - 110 2 LG PC 40 LG PC Available PC ZM-71SE Model Setting MASTERK10/60/200 K10/60/200 MASTERK500/1000 K500/1000 LG MKX00S Wiring Diagram (refer to P2-112) PC K200S/K300S/K1000S CPU port RS-232C [Wiring Diagram 1] RS-232C [Wiring Diagram 2] RS-422 [Wiring Diagram 4] RS-232C [Wiring Diagram 3] Communication Setting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of K10/60/200 Baud Rate 9600bps (fixed) Parity None (fixed) Transmission Data L
2 LG PC 2 - 111 Available Memory K10/60/200 Available: Memory Bit Write TYPE D (data register) M (auxiliary relay) 1 P (input/output relay) 2 K (keep relay) 3 TC (timer/current value) Unavailable: Remarks 0 Input : Read only 4 CC (counter/current value) 5 TS (timer/set value) 6 CS (counter/set value) 7 K500/1000 Available: Memory Bit Write TYPE P (input/output) 0 M (relay) 1 L (link relay) 2 K (keep relay) 3 F (special relay) 4 T (timer/current value) 5
2 - 112 2 LG PC Wiring The recommended communication parameter setting of both PC and ZM-** is as follows: RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 RXD 2 RD 3 TXD 3 SG 7 GND 5 D-sub 9pin(Male: ) * Use twist shielded cables. Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 TXD 2 RD 3 RXD 3 SG 7 GND 7 D-sub 25pin(Male: ) * Use twist shielded cables.
2 FANUC PC 41 2 - 113 FANUC PC Available PC ZM-71SE Mode Setting Power Mate Wiring Diagram (refer to P2-114) PC Port of CPU unit (JD14) of Power Mate-Model H/D RS-422 [Wiring Diagram 1] Communication Setting The following is a diagram to show the wiring of the cable which connects ZM-** to PC. Item Setting of PC Baud Rate 19200bps (fixed) Signal RS-422 (fixed) Port 0 (fixed) Parity Even (fixed) Transmission Code Data Length 8 (fixed) Stop Bit 1 (fixed) Comm.
2 - 114 2 FANUC PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC *1 FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 7 SG 7 SG D-sub 25pin(Male: ) * Use twist shielded cables.
2 FATEC PC 42 2 - 115 FATEK AUTMATION PC Available PC ZM-71SE Model Setting Wiring Diagram (refer to P2-116) Link Unit PC RS-232C [Wiring Diagram 1] FACON FB series FACON FB series FB-DTBR [Wiring Diagram 2] RS-422 [Wiring Diagram 3] CommunicationSetting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 - 116 2 FATEC PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 RXD1 1 RD 3 TXD1 2 RS 4 RTS1 3 CS 5 CTS1 4 SG 7 GND 6 D-sub 15pin(Male: ) * Use twist shielded cables. Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 RXD1 2 RD 3 TXD1 3 RS 4 RTS1 4 CS 5 CTS1 5 SG 7 GND 7 D-sub 9pin(Male: * Use twist shielded cables.
2 IDEC PC 43 2 - 117 IDEC PC Available PC ZM-71SE Model Setting RS-232C Cable made by IDEC [FC2A-KC1] or * Cable made by IDEC [FC2A-KC2] +RS-232C [Wiring Diagram 1] MICRO3 MICRO3 * Wiring Diagram (refer to P2-118) PC When using RS-232C cable made by IDEC [FC2A-KC2], connect the cable of [Wiring Diagram 1] to the D-sub 9 pins side of [FC2A-KC2] to communicate with ZM-**.
2 - 118 2 IDEC PC Set the memory to the extent of the memory range of each PC model. In case of using the [Bit Write] memory as the bit device of the [Output Action] is [Momentary W], the other bits will be cleared when the bit memory is output, because the [Bit Write] will be output by one word (refer to P5-10, reference 14-7 of ZM-71SE Instruction Manual). Use [TYPE] number to assign indirect memory for macro programs.
2 MODICON PC 44 2 - 119 MODICON PC Available PC ZM-71SE Model Setting Modbus RTU Wiring Diagram (refer to P2-120) PC Modbus RTU RS-232C [Wiring Diagram 1] CommunicationSetting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Baud Rate 9600bps Comm.
2 - 120 2 MODICON PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 RX 2 RD 3 TX 3 RS 4 DTR 4 CS 5 GND 5 SG 7 DSR 6 RTS 7 CTS 8 D-sub 9pin(Male: * Use twist shielded cables.
2 YAMATAKE PC 45 2 - 121 YAMATAKE PC Available PC ZM-71SE Model Setting Wiring Diagram (refer to P2-122) PC MX series RS-232C [Wiring Diagram 1] MX200/MX50 CommunicationSetting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Baud Rate 9600bps Port 1 1 Parity Even Even Transmission code Comm.
2 - 122 2 YAMATAKE PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-232C Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SD 2 SD 2 RD 3 RD 3 RS 4 RS 4 CS 5 CS 5 SG 7 SG 7 D-sub 25pin(Male: * Use twist shielded cables.
2 TAIAN PC 46 2 - 123 TAIAN PC Available PC ZM-71SE Model Setting PC TP02 TP02 Wiring Diagram (refer to P2-124) Port Communication Port (T/R+, T/R-) MMI Port (9pin) (4-5 Short Computer Link Mode) RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 2] CommunicationSetting The recommended communication parameter setting of both PC and ZM-** is as follows: Item Setting of PC Comm.
2 - 124 2 TAIAN PC Wiring The following is a diagram to show the wiring of the cable which connects ZM-** to PC. RS-422 Wiring Diagram 1 ZM-** (CN1) D-sub 25pin(Male: ) FG 1 SG 7 PC +SD 12 T/R+ -SD 13 T/R- +RD 24 SHLD -RD 25 * Use twist shielded cables. Wiring Diagram 2 ZM-** (CN1) D-sub 25pin(Male: ) PC FG 1 SG 7 RX+ 2 +SD 12 TX+ 3 -SD 13 PG/COM 4 +RD 24 GND 5 -RD 25 RX- 7 TX- 8 D-sub 9pin(Male: * Use twist shielded cables.
SHARP MANUFACTURING SYSTEMS CORPORATION ♦Information about Sharp programmable controller is available at our internet homepage http://sharp-world.com/sms-e/ 2.0v 5.2001 Printed in Japan (0.1.Y.