Installation guide

ManualsBrandsSharp ManualsOtherKB-3300JK

30" FreestandingRange

INSTALLATIONMANUAL

INSTALLATIONANDSERVICEMUSTBEPERFORMEDBYA QUALIFIEDINSTALLER.

IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL

INSPECTOR'SUSE.

READANDSAVETHESEINSTRUCTIONSFORFUTUREREFERENCE.

For SAFETY CONSIDERATIONS do not install a range in any combustible cabinetry which is not in

accord with the stated clearances and dimensions on page 2. See Figures 1 and 2.

CLEARANCESANDDIMENSIONS.............................. 2

IMPORTANTNOTES............................................. 3

IMPORTANTSAFETYINSTRUCTIONS......................... 3

ELECTRICALCONNECTIONS................................ 3-5

BACKSPLASHINSTALLATION.................................. 6

ANTI-TIP ....................................................... 7

MODELANDSERIALNUMBER................................. 8

CARE,CLEANINGANDMAINTENANCE...................... 8

® Insight _

Summary of content (8 pages)

PAGE 1
30" FreestandingRange INSTALLATION MANUAL INSTALLATION ANDSERVICEMUSTBE PERFORMEDBY A QUALIFIEDINSTALLER. IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL INSPECTOR'SUSE. READANDSAVETHESEINSTRUCTIONSFORFUTUREREFERENCE. For SAFETY CONSIDERATIONS do not install a range in any combustible cabinetry which is not in accord with the stated clearances and dimensions on page 2. See Figures 1 and 2. CLEARANCES ANDDIMENSIONS .............................. 2 BACKSPLASH INSTALLATION ..................
PAGE 2
INSTALLATION MANUAL minimum 30" to bottom of cabinet over cooktop 29 5/8" Jjustiabie 29 7/8" backspash width 42-48" with adjustiaNe backsplash 36" countertop height \ 30" openmg width 45 3/8" _ oven door open \'-,,. \xb /_ //_J _ //" 30" / door widths Figure Figure 1 Preferred electrical outlet area _ 2 __._?_ Figure 1 contains many range measurements planning your kitchen and/or range location. between for reference when • Provide adequate clearances combustible surfaces.
PAGE 3
INSTALLATION _If the information in this manual is not followed exactly, a fire or electrical shock may result causing property damage, personal injury or death. °, INJURY TO PERSONS ALL RANGES CAN TIP COULD • INSTALL ANTI-TIP BRACKET • Never use the range for warming or heating the room. Prolonged use of the range without adequate ventilation can be dangerous. • Do not store or use gasoline or other flammable vapors and liquids near this or any other range. Explosions or fires could result.
PAGE 4
INSTALLATION 208/240 MANUAL VOLT CONNECTION ACCESS INSTRUCTIONS The range can be set for 208V o1"240V. The voltage setting for your range is pre-set at 240V from the factory. Follow these steps to change the voltage setting. t Locate range. the voltage switch 2 Remove the screw and rotate the switch plate 180 ° as indicated in the Figure 3. a Reinsert the switch plate and replace screw as indicated in Figure 4. The voltage setting is indicated by the visible marking.
PAGE 5
INSTALLATION 3 Make sure all connections are tightened the rear access cover. See Figure 7. GROUNDING INSTRUCTIONS- ONLY 3-WIRE securely and replace connections. Tighten all 3 or 4-wire leads to the terminal block. Follow wire locations shown in Figure 10. DO NOT LOOSEN CONNECTIONS: Note: For 3-wire permanent continue with step 5.
PAGE 6
INSTALLATION MANUAL Parts Supplied r The range backsplash is adjustable so that you can customize it for your particular kitchen situation. The height can be adjusted froln the low position (6-inches high) to the highest position (12-inches high) in one inch increments. 4 Screws Remove screw fioln the cooktop back fralne end cap on both sides and screw from range back cover on both sides, as shown in Figure 12. 1 Backsplash I Ik_It,lq ;tl $.
PAGE 7
INSTALLATION MANUAL 2 DRILL PILOT HOLES AND FASTEN BRACKET Drill a 1/8-inch pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate 20 degree downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 5/32-inch pilot hole 1 3/4 inches deep. The screws provided may be used in wood or concrete material.
PAGE 8
INSTALLATION MODEL MANUAL AND SERIAL NUMBER LOCATION BEFORE YOU CALL FOR SERVICE The name plate, including model and serial number, is located on the faceplate behind the Microwave Drawer front. Read the BEFORE YOU CALL and operating instruction sections in your Operation Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective CARE, workmanship CLEANING AND MAINTENANCE Refer to the Operation Manual for cleaning instructions.