LC-13SH1U SERVICE MANUAL S74Y1LC13SH1U SERVICE MANUAL LCD COLOR TV LCD COLOR TV MODEL LC-13SH1U In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS MODEL LC-13SH1U Page SPECIFICATIONS ................................................................................................................................ 1-1 IMPORTANT SAFEGUARDS AND PRECAUTIONS .....
SPECIFICATIONS ANT. Input ........................... 75ohm Unbal., F type Reference Level .................. 20Vp-p (CRT Green Cathode) Test Input Signal ................. 400Hz 30% modulation Description Condition Unit Nominal Limit 1. Intermediate Freq. Picture Sound MHz MHz 45.75 41.25 - 2. Color Killer Sens. CH-2 CH-10 CH-55 dBµV dBµV dBµV 15 15 15 20 20 20 3. AFT Pull In Range (10mV input) - MHz ±2.1 ±0.
IMPORTANT SAFEGUARDS AND PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.
2. 3. 4. 5. a. b. specifications given on instrument labels and in the Product Safety & X-Radiation Warning note on the service data chassis schematic. High voltage is maintained within specified limits by close tolerance safety-related components/adjustments in the highvoltage circuit. If high voltage exceeds specified limits, check each component specified on the chassis schematic and take corrective action.
IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: • WARNING 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. A V • CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE REPLACE ONLY WITH SAME TYPE F3701 (2.0A, 250V), F3702 (1.25A, 250V), AND F6701 (6.3A, 250V) FUSE.
PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ne peut effectuer la réparation qu’ un technicien spécialisé qui s’est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT 1. N’entreprendre aucune modification de tout circuit. C’est dangereux. 2. Débrancher le récepteur avant toute réparation. A V • • PRECAUTION: POUR LA PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE, REMPLACER LE FUSIBLE PAR UN FUSIBLE DE MEME TYPE F3701 (2.0A, 250V), F3702 (1.
STANDARD NOTES FOR SERVICING Precautions for Using Lead-free Solder NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. 1 Employing lead-free solder Pb free mark (as shown below) indicates lead-free solder, and is attached on the PWBs and service manuals. For PWBs with Pb free mark, be sure to use lead-free solder. For PWB without Pb free mark, use standard solder. The alphabetical character following Pb shows the type of lead-free solder. Circuit Board Indications a.
How to Remove / Install Flat Pack-IC With Soldering Iron: (1) Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: (1) Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) Flat Pack-IC Desoldering Braid Soldering Iron Fig.
(4) Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 2. Installation (1) Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. (5) Release the flat pack-IC from the CBA using tweezers. (Fig.
Instructions for Handling Semi-conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2.
CABINET DISASSEMBLY INSTRUCTIONS 2. Disassembly Method NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. REMOVAL 1. Disassembly Flowchart ID/ LOC. No. This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally.
[1] Rear Cabinet S-1 S-2 S-1 S-1 S-1 S-1 4-2 Fig.
[8] Front Cabinet [6] Speaker L S-9 S-7 S-8 [3] LCD Main CBA [2] Main CBA S-6 [7] Speaker R S-10 [5] Function CBA [4] Liquid Crystal Panel S-5 S-6 S-4 S-7 S-4 S-3 S-3 Fig.
To Liquid Cristal Panel CLN104 CN310A CN321A CN311A Function CBA CN113B CN112B LCD Main CBA CN111B CN104 CN401 CN402 CN103A CN102A CN101A To Liquid Cristal Panel CN403 Main CBA CN404 CN801 CN802 To Speaker To Speaker Fig.
ELECTRICAL ADJUSTMENT INSTRUCTIONS 1. Initial Setting NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. General Enter the Service mode. NOTE: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available. Set the each initial data as shown on table 1 below.
BUTTON (on the service remote control) ITEM C-DG(C/D2) C-DB(C/D2) 3. Flicker Adjustment DATA VALUE Vol down 5 127 Vol down 6 131 7F Note: Use remote control unit 1. Enter the Service mode. (See page 5-1) 2. Press “2” button on the remote control unit. T h e following screen appears. FF LANGUAGE SPA/FRA STEREOTYP MTS ACCESSCODE ON Vol down BLACKLIGHT ON HD OFF HRD OFF NCM OFF ASPECT OFF 3. If Flicker Adjustment is not fit, the screen become the following. 2.
The following adjustment normally are not attempted in the field. Only when replacing the LCD Panel then adjust as a preparation. Method 2 Test point Adj. Point 5. White Balance Adjustment Screen Purpose: To mix red, green and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish. CH buttons VIDEO 1 VIDEO 2 White Purity (APL 80% and 40%) Spec.
6. Sub-Brightness Adjustment Purpose: To mix red, green and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish. Confirmation at [VIDEO-1] 1. Set CG951 to 7/5/3 IRE 3-step grayscale. 7 IRE 5 IRE 3 IRE TEST PATTERN (7/5/3 IRE) 2. Apply CG951 video signal to VIDEO1 input. 3. Enter the Service mode. 4. Make sure that contrast and brightness controls are set to initial position. 5. Confirm “5 IRE” position was biginning to bright. 6.
TROUBLESHOOTING Table of Contents for the Troubleshooting Flow Charts Flow Chart No. Description Page 1 The power cannot be turned on. 6-2 2 The fuse blows out. 6-2 3 When the output voltage fluctuates. 6-2 4 When buzz sound can be heard in the vicinity of power circuit. 6-2 5 AL-8V is not outputted. 6-2 6 AL+3.3V is not outputted. 6-3 7 AL+40V is not outputted. 6-3 8 AL+5V is not outputted. 6-3 9 AL+33V is not outputted. 6-3 10 AL+12V is not outputted.
1. POWER SUPPLY SECTION FLOW CHART NO.1 The power cannot be turned on. No Is the fuse (F601) normal? See FLOW CHART No.2 Yes Is normal state restored when once unplugged power cord is plugged again several seconds? No Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (Q601,Q603.T601,D605,D606,D607,D608,C605, C606,C610,C654) Yes Is the AL +3.
FLOW CHART NO.6 AL+3.3V is not outputted. Is 3.3V voltage supplied to the cathode of D514? No Check D635,C637 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit and service it if defective. FLOW CHART NO.7 AL+40V is not outputted. Is approximately 40V voltage supplied to the emitter of Q516? No Check D645,D646,C644 and their periphery circuit, and service it if defective.
FLOW CHART NO.11 REG+5V(1) is not outputted. No See FLOW CHART No.9 Is approximately 12V voltage supplied to Pin(1) of IC604? Yes Check IC604,C603 and their periphery circuit, and service it if defective. FLOW CHART NO.12 REG+5V(2) is not outputted. Is 7.4V voltage supplied to Pin(1) of IC603? No See FLOW CHART No.8 Yes Check IC603,C673 and their periphery circuit, and service it if defective. FLOW CHART NO.13 P-ON+3.3V(D) is not outputted. Is approximately 4.
FLOW CHART NO.16 PANEL+24V is not outputted. Is approximately 40V voltage supplied to the collector of Q501? No See FLOW No.7 Yes Check Q501,Q502,Q511 and their periphery circuit, and service it if defective. FLOW CHART NO.17 PANEL+5.4V is not outputted. Is approximately 12V voltage supplied to the collector of Q503? No See FLOW No.10 Yes Check Q503,Q504,Q514 and their periphery circuit, and service it if defective. FLOW CHART NO.18 PANEL-12V is not outputted.
FLOW CHART NO.21 The key operation is not functioning. Are the contact point and installation state of the key switches (SW101,SW102,SW103,SW104,SW105, SW107,SW116) normal? No Re-install the switches (SW101,SW102,SW103, SW104,SW105,SW107,SW116) correctly or replace the poor switch.
2. VIDEO SIGNAL SECTION FLOW CHART NO.23 Picture does not appear normally. (Tuner input / Video input/S-Video input.) Are the video signals inputted to the specific input terminal? Check the line between each pin of IC781 and input terminal and service it if defective. Are the luminance signals inputted to the Pin(1) of IC781? No Check the line between Pin(1) of IC781 and JK721, and service it if defective.
3. AUDIO SIGNAL SECTION FLOW CHART NO.25 Audio is not outputted normally. (Tuner input.) No Check TU1,SF,IC11,CF32 and their periphery circuit, and service it if defective. Are the audio(L/R) signal inputted to the Pin(4,11) of IC852? Yes No Check IC851 and the periphery circuit, and service it if defective. Are the audio(L/R) signal outputted to the Pin(3,13) of IC852? Yes No Check IC852 and the periphery circuit, and service it if defective.
7-1 (NO CONNECTION) SCL CN115 IS SDA USED FOR ADJUSTMENT BUS-OPEN AT FACTORY WP 7 SDA 5 SCL 6 IC181 (MEMORY) +5V 12 22 17 6 7 18 20 35 31 32 19 40 41 8 23 CN115 1 2 4 VGH-H BACKLIGHT-SW BACKLIGHT-ADJ PROTECT-1 PROTECT-2 P-ON-H VOLUME A-MUTE INPUT-0 INPUT-1 S-SW SCL SDA PROTECT-3 BUS-OPEN RESET 21 OUTCON 16 CS 24 SCLK 25 SOUT 26 HD 169 KEY-IN1 3 KEY-IN2 4 RCV-IN 11 XIN 42 XOUT 43 IC333 (TV MICRO CONTROLLER) 4 6 RESET 5 IC161 A/B Q121 3.3V<-->5V CONVERTER RESET Q161 +3.
7-2 JK728 VIDEO-Pr IN JK727 VIDEO-Pb IN JK726 VIDEO-Y IN JK721 S-VIDEO IN JK722 VIDEO1 IN TO SYSTEM CONTROL BLOCK DIAGRAM C Y S-SW SCL SDA SCL 4 SDA 5 AGC 1 IF 11 TU1 (TUNER UNIT) BUFFER Q706 BUFFER Q705 BUFFER Q704 SAW FILTER SF11 14 16 17 IC11 LPF RF AGC VIF AMP APC SIF AMP EQ AMP IFAGC DET VIDEO DET VCO (IF SIGNAL PROCESS) NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. INPUT-1 INPUT-0 4.5MHz FILTER CF32 BUFFER Q709 4.
7-3 JK730 AUDIO2(R) IN JK729 AUDIO2(L) IN JK724 AUDIO1(R) IN JK723 AUDIO1(L) IN TO IF/VIDEO BLOCK DIAGRAM MAIN CBA SIF 24 27 21 SAP FILTER STEREO FILTER 9 10 SW CTL (R-CH) (L-CH) TUNER AUDIO1 AUDIO2 TUNER 4 AUDIO1 2 AUDIO2 1 11 15 12 SAP DEMOD OFFSET CANCEL 3 13 IC852 (INPUT SELECT) I2C DECORDER VCA IC851 (MTS/SAP AUDIO SIGNAL PROCESS) NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD.
7-4 LCD MODULE TO IF/VIDEO BLOCK DIAGRAM CN103A TO IF/VIDEO BLOCK DIAGRAM CN103A VREF(0) VREF(1) VREF(3) VREF(5) VREF(7) VREF(8) VREF(10) VREF(11) V-COM V-COM V-COM V-COM CN311A 3 4 6 8 9 10 11 12 17 18 19 20 VIDEO-Y 19 VIDEO-Pb 21 VIDEO-Pr 23 CN113B CN113B CVBS 13 S-VIDEO-C 17 S-VIDEO-Y 15 WF26 WF16 WF17 WF19 WF21 WF22 WF23 WF24 WF25 VREF(0) VREF(1) VREF(3) VREF(5) VREF(7) VREF(8) VREF(10) VREF(11) V-COM LCD MAIN CBA UNIT A/D 60 TO SYSTEM CONTROL BLOCK DIAGRAM A/D A/D A/D 52 B G A/D
AC601 AC CORD Q601 SWITCHING F601 4A/125V 4A/125V IC601 ERROR VOLTAGE DET BRIDGE RECTIFIER Q603 SWITCHING CONTROL D605 - D608 LINE FILTER HOT L601,L602 HOT CIRCUIT. BE CAREFUL. 7-5 1 2 4 3 4 T602 6 2 1 D649 12 9 10 11 8 7 COLD CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
SWITCHING Q401 Q427 +12V SWITCHING BACKLIGHT-SW BACKLIGHT-ADJ PROTECT-1 TO SYSTEM CONTROL BLOCK DIAGRAM AL+12V SWITCHING BACKLIGHT-ON Q403 Q408 Q407 Q409 + Q406 OVER VOLTAGE PROTECTOR Q405 PWM CONTOROL Q410 NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD.
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. Standard Notes Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE_A,_V. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
Main 1/5 Schematic Diagram NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. MAIN 1/5 Ref No.
Main 2/5 Schematic Diagram NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. MAIN 2/5 Ref No.
Main 3/5 Schematic Diagram NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. MAIN 3/5 Ref No.
Main 4/5 Schematic Diagram NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. MAIN 4/5 Ref No.
Main 5/5 Schematic Diagram CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 4A/125V CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
Function Schematic Diagram NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD.
LCD Main 1/2 Schematic Diagram NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. LCD 1/2 Ref No.
LCD Main 2/2 Schematic Diagram NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. LCD 2/2 Ref No.
Main CBA Top View CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. 4A/125V CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
Main CBA Bottom View CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 4A/125V CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
Function CBA Top View NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. FUNCTION Ref No.
WAVEFORMS & VOLTAGE CHART MAIN CN101A PIN NO. Voltage / WF No. 1 12.4 2 9.0 3 0 4 3.3 5 5.0 6 0 7 25.2 8 -10.9 9 0 CN102A PIN NO. Voltage / WF No. 1 3.3 2 0 3 0 4 0 5 3.3 6 3.3 7 3.3 8 3.3 9 WF1 10 0 11 3.3 12 0.9 13 0 14 1.8 15 2.3 16 2.1 17 3.3 18 WF2 19 WF3 20 0 21 3.2 22 4.8 23 ----- CN103A PIN NO. Voltage / WF No. 1 WF4 2 0 3 WF5 4 0 5 WF6 6 0 7 WF7 8 0 9 WF8 10 0 11 FW9 12 0 13 ----14 3.3 15 ----16 0 17 ----18 0 19 3.3 20 0 21 1.8 22 0 23 3.3 LCD MAIN CN104 PIN NO. Voltage / WF No. 1 3.3 2 3.
WF7 WF1 ~ WF10 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.
LCD CBA Measurement Point WF11 ~ WF20 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) CAUTION! Since the handling of CN310A,CN311A and CN321A tends to lead to destruction easily , be careful of it enough. (especially CN321A.
WF21 ~ WF32 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.
CLN310 YOBI 1 YOBI 2 YOBI 3 YOBI 4 YOBI 5 YOBI 6 YOBI 7 YOBI 8 YOBI 9 YOBI 10 POL LP LBR STH-1 STH-2 GND GND QCLK GND GND B(0) B(1) B(2) B(3) GND B(4) B(5) B(6) B(7) GND G(0) G(1) G(2) G(3) GND G(4) G(5) G(6) G(7) GND R(0) R(1) R(2) R(3) GND R(4) R(5) R(6) R(7) GND CN310A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 CN321A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 CN311A 1
IC PIN FUNCTION DESCRIPTIONS IC11 (VIF/SIF) Pin No. IC505 (PST600L) Signal Name Pin No. Function Signal Name Function 1 Video out Video Output 1 Vcc Input Power Supply 2 Video in Video det Input 2 GND GND 3 Vcc Power Supply 3 Vout Output Power Supply 4 Video det out Video det Output 5 APC APC Filter 6 VCO_F/B VCO Feedback 7 SIF in SIF Input 8 SIF out SIF Output 9 Audio out Audio Output 10 Audio Level Cont.
Pin No. Signal Name Pin No. Function 10 B Switching Control 11 A Switching Control 12 0X Video Signal Input 13 1X Video Signal Input 14 X-COM Video Signal Output 15 Y-Com Video Signal Output 16 Vdd Power Supply IC801 (AN17812A) Pin No.
Pin No.
EXPLODED VIEWS NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. Cabinet NOTE: The LCD Main CBA is one of two types (Type :A or Type:B). When ordering the LCD Main CBA, only Type: B (new version) is supplied. Therefore, install it by using four screws L9. A1 LCD Main CBA (Type: A) A11 A3 L11 B18 Function CBA SP802 B1 L2 See Electrical Parts List for parts with this mark.
LCD Panel Display 5 1 4 1 2 1 3 12-3 L0170LEX
Packing S2 Some Ref. Numbers are not in sequence.
MECHANICAL PARTS LIST LISTE DES PIÈCES MÉCHANIQUES PARTS REPLACEMENT Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are identified by # and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
Ref. No. SP802 S1 S2 S3 S4 X1 X2# X3 X4 X5# X7 Part No. 9HSSD0807XQ002 9HS1EM320121 9HS1EM020053 9HS1EM020054 9HS0EM301908 9HS0EM408420 9HS1EMN20180 9HSREMT21SH001 9HSB0M451T0001 9HS1EMN20181 9HS1EMN20157 Description SPEAKER S0407F10 CARTON STYROFOAM TOP L0170UA STYROFOAM BOTTOM L0170UA SET BAG L0110UA BAG POLYETHYLENE 235X365XT0.03 OWNER’S MANUAL L0270UA”EN/FR” REMOTE CONTROL RRMCGA336WJSA DRY BATTERY R6P/2S OWNER’S MANUAL SPANISH/WARRANTY QUESTIONNAIRE CARD L0170UA LCD Panel Display Ref. No.
ELECTRICAL PARTS LIST LISTE DES PIÈCES ÉLECTRIQUES PARTS REPLACEMENT NOTE: CBA AND PWB MEANS PRINTED WIRING BOARD. Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are identified by # and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
Ref. No. C131 C132 C161 C163 C165 C171 C172 C173 C181 C182 C184 C187 C191 C192 C193 C194 C195 C196 C201 C202 C203 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 C217 C218 C219 C220 C221 C222 C223 C224 C225 C226 C227 C228 C229 C230 C231 C232 C233 C234 C235 C236 C251 C252 C253 C254 C255 C256 C257 C258 C259 C260 C261 C262 C263 C264 C265 C266 Part No.
Ref. No. C267 C268 C269 C270 C271 C272 C274 C275 C279 C280 C281 C282 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C325 C326 C327 C328 C329 C330 C331 C332 C333 C334 C335 C351 C352 C353 C361 C362 C363 C364 C365 C366 C371 C372 C373 C374 C375 C380 C381 C382 CONNECTORS CN111B CN112B CN113B CN115 Part No.
Ref. No. CN310A CN311A CN321A DIODES D251 D255 D256 D271 D273 D281 ICs IC161 IC181 IC202 IC275 IC276 IC333 COILS L251 L252 TRANSISTORS Q121 Q161 Q251 Q252 Q253 Q254 Q272 RESISTORS R135 R136 R137 R138 R139 R140 R141 R142 R143 R144 R146 R147 R148 R149 R150 R151 R152 R153 R154 R155 R156 R157 R164 R165 R172 R173 R174 R175 R176 R177 R178 R179 R180 R181 R182 R183 R184 R185 R186 R187 Part No.
Ref. No. R188 R189 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R212 R213 R214 R215 R216 R217 R218 R219 R220 R221 R222 R223 R224 R225 R226 R227 R228 R229 R230 R231 R232 R251 R252 R253 R254 R255 R256 R257 R259 R260 R261 R262 R263 R264 R265 R266 R267 R268 R270 R272 R273 R275 R276 R277 R278 R279 R280 R281 R282 R283 R287 R288 R289 R290 R291 R297 Part No.
Ref. No. R298 R299 R341 R342 R343 R344 R345 R346 R347 R351 R352 R353 R354 R355 R357 R361 R362 R363 R364 R371 R372 R373 R374 R375 R377 R381 R382 R383 R384 R385 R386 R387 R388 R389 R390 R391 R392 R393 R395 MISCELLANEOUS X171 Part No.
Ref. No. C37 C38 C39 C40 C41 C42 C43 C44 C401 C402 C403 C404 C407 C409 C410 C411 C412 C413 C414 C415 C416 C417 C418 C419 C420 C421 C422 C423 C424 C425 C426 C427 C428 C429 C430 C431 C433 C434 C435 C436 C437 C438 C439 C440 C501 C502 C505 C506 C507 C509 C510 C512 C513 C514 C517 C518 C521 C522 C523 C524 C527 C528 C533 C536 C538 C539 C540 C541 C543 Part No.
Ref. No. C544 C601# C602# C603 C605 C606 C608 C610# C612 C613 C614 C615 C630# C632 C633 C634# C635 C636 C637# C641# C642# C644# C645# C646 C648 C649 C651 C652 C653 C654# C657 C659 C660 C673 C701 C703 C704 C705 C707 C708 C709 C711 C712 C714 C715 C717 C718 C720 C722 C724 C726 C728 C730 C732 C733 C735 C736 C738 C739 C740 C741 C781 C782 C784 C785 C786 C788 C801 C802 Part No.
Ref. No. C803 C804 C805 C809 C810 C811 C812 C816 C817 C818 C819 C820 C851 C852 C853 C854 C855 C856 C857 C858 C859 C860 C861 C862 C863 C864 C865 C866 C867 C868 C869 C883 CONNECTORS CN104 CN401 CN402 CN403 CN404 CN801 CN802 CN101A CN102A CN103A DIODES D42 D43 D44 D402 D403 D404# D405# D406# D407# D408 D409 D410# D411# D412 D413 D414 D415 D420 D421 D422 D423 D428 D430 D432 D433 Part No.
Ref. No. D434 D435 D436 D437 D438 D439 D440 D441 D442 D443 D444 D445 D446 D447 D448 D449 D450 D451 D452 D453 D454 D455 D456 D457 D458 D459 D460 D461 D462 D463 D464 D465 D466 D467 D468 D469 D470 D471 D480 D481 D501# D502 D503 D504# D505 D506 D509# D510 D511# D512 D514 D515 D517 D519 D520 D521 D523 D524 D532 D533 D534 D535 D536 D537 D538 D539 D540 D541 D542 Part No.
Ref. No. D543 D547 D549 D605# D606# D607# D608# D609 D611# D612 D613 D615# D616# D620 D624 D630# D631# D632# D633# D634 D635# D636 D640 D641 D642# D643# D644# D645# D646# D647# D648# D649# D650 D651 D653# D668 D701 D702 D703 D801 D802 D803 D810 ICs IC11 IC502 IC503 IC504 IC505 IC506 IC601# IC603# IC604 IC781 IC801 IC851 IC852 COILS L11 L13 L15 L31 L32 L33 L34 L401 L403 L501 L601# Part No.
Ref. No. L602# L630 L632 L701 L851 TRANSISTORS Q31 Q401# Q403 Q404 Q405 Q406 Q407# Q408 Q409 Q410 Q411# Q412# Q415# Q416# Q419 Q420 Q421 Q422 Q423 Q424 Q425 Q426 Q427 Q428 Q501 Q502 Q503 Q504 Q505 Q507 Q508 Q509# Q511 Q512 Q513 Q514 Q515 Q516 Q517 Q601# Q603# Q633 Q701 Q702 Q703 Q704 Q705 Q706 Q707 Q708 Q709 Q802 Q803 RESISTORS R11 R12 R16 R17 R20 R21 R22 R24 R30 Part No. Description 9HSLBG00ZTU012 9HSJW7.5T 9HSLAXJATTU220 9HSJW5.0T 9HSJW5.0T LINE FILTER TLF14CB3321R0 PCB JUMPER D0.6-P7.
Ref. No. R33 R34 R37 R41 R43 R45 R046 R63 R65 R403 R404 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R427 R428 R429 R430 R440 R441 R442 R443 R444 R445 R446 R447 R448 R458 R459 R460 R461 R462 R463 R464 R465 R466 R467 R468 R469 R470 R471 R472 R473 R474 R475 R476 R477 R478 R479 R480 R481 Part No.
Ref. No. R482 R483 R484 R485 R486 R487 R488 R489 R490 R491# R492 R493 R494 R503 R504 R505 R510 R511 R512 R513 R514 R517 R518# R519# R521 R522 R523 R539 R540 R543 R544 R545 R546 R547 R548 R549 R552 R555 R556 R557 R558 R561 R570 R571 R572 R573 R575 R577 R578 R579 R580 R581 R582 R583 R584 R585 R586 R587 R601# R603# R604 R605 R606 R607 R608 R609 R610 R613 R620 Part No.
Ref. No. R621 R622 R623 R633 R634# R635 R636 R637 R642# R643# R645 R646 R647 R648 R650 R651 R652 R653 R654 R655 R656 R658 R702 R703 R705 R707 R708 R710 R711 R713 R715 R716 R718 R719 R721 R723 R724 R725 R726 R727 R728 R729 R730 R732 R733 R735 R737 R738 R740 R741 R743 R745 R746 R748 R749 R751 R753 R754 R755 R756 R757 R758 R759 R760 R781 R782 R783 R784 R785 Part No. 9HSCX4JATZ0821 9HSJW5.0T 9HSCX4JATZ0222 9HSRXAJR5Z0473 9HSRXAJR5Z0153 9HSRXAJR5Z0273 9HSJW5.
Ref. No. R786 R787 R788 R789 R791 R792 R798 R799 R801 R802 R803 R804 R805# R806 R807# R808 R809 R810 R811 R812 R813 R814 R816 R817 R818 R820 R821 R822 R823 R824 R825 R826 R827 R829 R830 R831 R832 R833 R834 R837 R838 R839 R851 R852 R855 R857 R893 MISCELLANEOUS AC601# B6 B7 B8 BC401 BC602 BC632 BC637 BC638 BC639 BC642 CF31 CF32 CLN108 F601# FH601 FH602 GP641# J108 J115 J178 Part No.
Ref. No. J179 J229 J249 J286 J292 JK721 JK722 JK723 JK724 JK726 JK727 JK728 JK729 JK730 JK801 JS701 JS702 JS703 JS704 L4 SA601# SF11 T401# T402# T403# T404# T602# TP300 TP401 TU1 VR601 Part No. 9HSRXAZR5Z0000 9HSRXAZR5Z0000 9HSRXAZR5Z0000 9HSRXAZR5Z0000 9HSRXAZR5Z0000 9HSYEJ040JC001 9HSXRJ010RP005 9HSXRJ010RP006 9HSYRJ010RP001 9HSXRJ010RP007 9HSXRJ010RP008 9HSXRJ010RP009 9HSXRJ010RP006 9HSYRJ010RP001 9HSYSL020LY002 9HSRXAZR5Z0000 9HSRXAZR5Z0000 9HSRXAZR5Z0000 9HSJW7.
Ref. No. SW101 SW102 SW103 SW104 SW105 SW107 SW116 MISCELLANEOUS CLN104 J277 RCV101 Part No. Description 9HSST0101AL060 9HSST0101AL060 9HSST0101AL060 9HSST0101AL060 9HSST0101AL060 9HSST0101AL060 9HSST0101AL060 TACT SWITCH SKHHARA010 TACT SWITCH SKHHARA010 TACT SWITCH SKHHARA010 TACT SWITCH SKHHARA010 TACT SWITCH SKHHARA010 TACT SWITCH SKHHARA010 TACT SWITCH SKHHARA010 9HSX1L0170-003 9HSRXAZR5Z0000 9HSSESJRSRM006 WIRE ASSEMBLY WX1L0170-003 CHIP RES.
LC-13SH1U COPYRIGHT © 2004 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP ELECTRONICS CORPORATION Oct.
