LC-20B2UA LC-20B2UB SERVICE MANUAL S42I5LC20B2UB LCD COLOR TELEVISION MODELS LC-20B2UA LC-20B2UB In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. OUTLINE The 20" LCD panel used in the LC-20B2UA has been redesigned as from the April production. Accordingly, the circuitry and the adjustment procedures have been partially changed.
LC-20B2UA LC-20B2UB IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be perfomed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: ground, such as electrical conduit or electrical ground connected to an earth ground. • Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resisor.
LC-20B2UA LC-20B2UB PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. conduite électrique ou une prise de terre branchée à la terre. • Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension en travers de la résistance.
LC-20B2UA LC-20B2UB Precautions for using lead-free solder 1 Employing lead-free solder "Digital PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper. 2 Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder.
LC-20B2UA LC-20B2UB Specifications Items Lamp life Viewing angles Audio amplifier Speakers Terminals LC-20B2UA/B Model LCD panel Number of dots Video color systems Destination TV Standard (CCIR) TV function TV Tuning System STEREO CATV 3 Dimensional Y/C separation circuit Digital comb filter Brightness AV1 AV2 COMPONENT Antenna Headphone OSD language Power Consumption Power supply Weight Accessories Environmental Conditions 19.
CH To change the vertical angle of the LCD TV set, tilt the screen up to 5 degrees forward or 10 degrees backward. The TV set can also be rotated 50 degrees horizontally. Please adjust the angle so that the TV set can be watched most comfortably. A green indicator lights when the power is on and a red indicator lights when in the standby mode (the indicator will not light when the main power is off). POWER indicator The SLEEP indicator lights up red when the SLEEP TIMER is set to on.
To mount the cover, insert the 2 hooks on the bottom of the cover into the cabinet and press on the upper part of the back cover until the tab locks in place with a click. Before connecting a connection cord into the rear terminal, remove the back cover. Push in the tab and pull out the back cover carefully.
LC-20B2UA LC-20B2UB Dimensions 24-51/64 /630 11-27/32 /301 15-1/64 /381.5 18-41/64 /473.5 15-55/64 /403 14-29/32 /379 4-7/32 /107.3 2-55/64 /72.6 VIDEO AV-IN1 L R L S-VIDEO AUDIO R COMPONENT Y HEAD PHONE PB 29 18- /64 /468.8 AUDIO VIDEO AV-IN2/OUT PR L AUDIO ANT. R POWER INPUT DC13V 2-25/64 /60.8 9-1/32 /229.
LC-20B2UA LC-20B2UB REMOVING OF MAJOR PARTS 1. Remove the two back covers. 2. Remove the table stand fixing screws (4 pcs.). 3. Remove the rear cabinet fixing screws (14 pcs.) and detach the cabinet. ( 3 : XBBSF30P06000, 3 : XEBSF40P16000) 4. Remove the reinforcement angle fixing screws (4 pcs.). 5. Detach the connector from each PWB.
LC-20B2UA LC-20B2UB 6. Remove the digital PWB fixing screws (3 pcs.). 7. Remove the inverter-A PWB fixing screws (2 pcs.). 8. Remove the inverter-B PWB fixing screws (1 pc.). 9. Detach the chassis frame cover. 10. Remove the analog PWB fixing screws (3 pcs.). 11. Remove the RC/LED PWB fixing screws (2 pcs.). 12. Remove the control PWB fixing screws (2pcs.).
LC-20B2UA LC-20B2UB » Precautions in handling the LCD panels 1. Work in a clean room (with humidities below 50%). 2. Be sure to wear an anti-static armband. 3. Handle the panels on an electroconductive mat. 4. Be careful not to fall, shake and shock the panels. 14.Remove the four screws and open the LCD display unit. 15.Remove the ITO earth angle fixing screw (1 pc.). 16.Detach the reflection/deflection, prism, diffusion, ITO sheets and diffusion plate. 17.Remove the lamp holder fixing screws (6 pcs.). 18.
LC-20B2UA LC-20B2UB ADJUSTING PROCEDURE OF EACH SECTION The best adjustment is made before shipping. If any position deviation is found or after part replace is performed, adjust as follows. 1. Preparation for Adjustments (1)Use the exclusive-use AC adapter or stable DC power supply. AC adapter: UADP-0243CEPZ DC power supply: 13 ± 0.5V 2. Special mode setting procedure (1)After initialization of E2PROM the mode is changed to the adjustment mode.
LC-20B2UA LC-20B2UB 4. Adjustments Adjustment Adjusting conditions Adjusting method 1 B+ Adjustment (R3760) 1. Connect the DC voltmeter to pin 2 of P3702. 1. Adjust the "B+ Adj" value to 5.0±0.02V with R3760. Make exact adjustment of the 5.00V level because it will be the reference for all the other supply voltages. Be sure to make this adjustment together with the main PWB (digital PWB). During the adjustment, be also careful not to allow the voltage at pin (2) of P3702 to go above 5.3 V.
LC-20B2UA LC-20B2UB Adjustment 7 E2PROM data write Adjusting conditions Adjusting method 1. Call up the adjustment process menu If the wrong data has been sent: and get Page 6 displayed onscreen. 1. Initialize the E 2 PROM. (Take the special mode setting procedure (1).) 2. Enter “A40000002681” for the “I2C 2. Take the adjustment steps 2 thru 7. DATA” item in Line 1. 3. Move the cursor to the “I2C DATA” item in Line 2 and carry out “SEND” with the right cursor key. 5. Shipping setting list Channel ....
LC-20B2UA LC-20B2UB Test patterns in adjustment process mode [1] IC801 (Video decoder) test patterns 1-1. Getting the test patterns displayed Put the screen in AV1, AV2 or COMPONENT but keep out any signal. Call the adjustment process mode, select “TEST PATTERN” in the 3rd line of page 7, make the settings 1 thru 6, and the following test patterns show up. 1-2.
LC-20B2UA LC-20B2UB Pin functions of microprocessor IC (IC2001) RH-iXA154WJZZQ No.
LC-20B2UA LC-20B2UB Adjustment process mode menus at a glance Page Item Initial setting Function Adjust/modify Basic settings 1 INCH SIZE MODEL SYSTEM NTSC PWN FREQ PAL PWM FREQ NTSC PWM DUTY PAL PWM DUTY TV GAIN ERROR NO RESET V-CHIP CANADIAN VCHIP B2UAVER 20 B2UA N358 OCO OBD 0 0 OFF 0 1 OFF Inch unit select Model number Color system select Dimmer frequency setting Dimmer frequency setting Dimmer duty setting Dimmer duty setting Auto gain setting in TV mode Lamp error count & reset VCHIP line mute
LC-20B2UA LC-20B2UB Page Item Initial setting Function Adjust/modify Video adjustments (VPC settings) 6 I2C DATA I2C DATA CBW NOSEL DDR HDG VDG VPK KILVL 08 KILHY 05 VSYNC DELAY DVCO AUTO LCK 0 WAIT 1 3 1 3 0 0 08 05 29 -720 1 I2C bus control IC data write & read Write & read execution Chroma band pass setting Comb filter setting Comb filter setting Comb filter setting Comb filter setting Comb filter setting Color killer level setting Color killer hysteresis setting V sync phase setting DVCO setting L
LC-20B2UA LC-20B2UB Page Item Initial setting Function Adjust/modify Video adjustments (TV, composite & S video) 11 12 13 14 15 PAL AV COLOR PAL AV TINT PAL BRIGHTNESS PAL PEAKING FILTER PAL AV H-PEAKING PAL AVO START PAL SFIF PAL SCINC1 PAL AV LDLY SECAM AV COLOR SECAM AV TINT SECAM BRIGHTNESS SECAM PEAKING FILTER SECAM AV H-PEAKING SECAM AVO START SECAM SFIF SECAM SCINC1 SECAM AV LDLY PAL-M TV COLOR PAL-M AV COLOR PAL-M TV TINT PAL-M AV TINT PAL-M BRIGHTNESS PAL-M PEAKING FILTER PAL-M TV H-PEAKING
LC-20B2UA LC-20B2UB Page Item Initial setting Function Adjust/modify Search AFT reference settings & LCD controller settings (NTSC) 16 AFT UP AFT DOWN NTSC 01 NTSC 02 NTSC 03 NTSC 04 NTSC 05 NTSC 06 NTSC 07 NTSC 08 NTSC 09 NTSC 0A NTSC 10 NTSC 11 NTSC 12 NTSC 13 NTSC E0 NTSC E1 NTSC F0 NTSC F1 NTSC F2 NTSC F3 NTSC F4 NTSC F5 NTSC F6 NTSC F7 NTSC 14 G/A TEST PATERN 2.7 1.
LC-20B2UA LC-20B2UB Page Item Initial setting Function Adjust/modify Gradation & COM settings 18 19 V255 V255 BIAS V235 V235 BIAS V176 V176 BIAS V112 V112 BIAS V64 V64 BIAS V32 V32 BIAS V21 V21 BIAS V17 V17 BIAS V7 V7 BIAS V0 V0 BIAS VGL ADJ VGL COM COM G/A READDATA G/A READDATA 255 127 222 127 129 150 96 170 65 40 72 100 43 50 52 145 27 65 0 80 27 215 179 00 00 WAIT Gradation power reference voltage Gradation power reference voltage Gradation power reference voltage Gradation power reference voltage
Check IC801 and its peripheral circuits. Check the IC801 signal input line. No Check the related lines, IC801 itself and its peripheral circuits. Are the waveforms at pins (10), (11), (13), (15) and (17) of IC1201 as specified? Yes No No Check IC1201 and its peripheral circuits as well as the LCD panel voltage and waveform. Check the IC801 signal output line, IC801 itself and its peripheral circuits.
No TV output 23 Are inputs and outputs of IC801 as specified? Yes No Check IC402 and its peripheral parts. Check IC801 and its peripheral circuits. Does the video decoder No test pattern appear? Yes Check IC1201, its peripheral circuits and the LCD panel. Does the LCD controller test No pattern appear? No Check IC402 and its peripheral parts.
No No No VIDEO color Check J3701, its peripheral parts and connection cable. Yes Is any of T3701’s primary No side, Q3700 and S4701 shortcircuited? Yes Disconnect F3701and F3702. Is the load side short-circuited? Check all the settings on the microprocessor’s adjust process menu. No TV color No color Check the secondary-side load of T3701.
No sound from headphone 25 Check the speakers and their peripheral parts. Yes Are inputs at pins (2) and (4) as well as outputs at pins (8) and (12), all of IC3305, as specified? Yes Are outputs at pins (1) and (7) of IC3301/ IC3302/IC3303 as specified? Yes Are input and output of IC3304 as specified? Yes Is pin (53) of IC2001 at “L”? No No No No Check the line in question, IC3301 and its peripheral parts. Check IC3301, IC3302, IC3303 and their peripheral parts.
LC-20B2UA LC-20B2UB CHASSIS LAYOUT H CONTROL Unit DIGITAL Unit G F E ANALOG Unit D C B RC/LED Unit A 1 2 3 4 5 6 26 7 8 9 10
LC-20B2UA LC-20B2UB INVERTER-A Unit INVERTER-B Unit 10 11 12 13 14 15 27 16 17 18 19
LC-20B2UA LC-20B2UB BLOCK DIAGRAM H ANALOG UNIT I2C TUNER TU3201 TV-V SIF SY, SC V1 L1, R1 AV1 S-VIDEO INPUT G SIF-AMP. Q3201 Q3202 V2/VO AV2 INPUT OUTPUT AUDIO IN/OUT SWITCH IC3501 Q3500 L2, R2 F VIDEO SWITCH IC402 VOUT V SW IC 6d B AMP. IC7201 Y, PB, PR COMPONENT INPUT DL, DR AUDIO DECODER (MSP) IC3304 DC IN DC13V E TV-V V1 V2 V2 VIDEO IN/OUT SWITCH Q3501-Q3505 AUDIO FILTER IC3301 IC3302 IC3303 I2C SYNC SEPARATER.
LC-20B2UA LC-20B2UB I2C SYOUT, SCOUT Y and C SWITCH IC7101 DIGITAL UNIT 3D Y/C SEPARATOR IC7001 IC7002 YO, CO V1SY,V1SC REGULATOR IC7102 IC7701 RESET IC7004 I2C SY, SC DEO TCH 402 AV1 V V1SY LCD CONTROLLER IC1201 VOUT VIDEO SWITCH IC7202 AMP. 01 VIDEO DECODER (VPC) IC801 DY LCD PANEL DY FIFO IC1202 DY, PB, PR 3.3V REG.
LC-20B2UA LC-20B2UB DESCRIPTION OF SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: CAUTION: 1. The voltages at test points are measured on exclusive AC adaptor and the stble supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. This circuit diagram is original one, therefore there may be a slight difference from yours.
LC-20B2UA LC-20B2UB SCHEMATIC DIAGRAM ËCONTROL and RC/LED Unit H G F E D C B A 1 2 3 4 31 5 6
LC-20B2UA LC-20B2UB Ë DIGITAL Unit-1/5 H G F E D C B A 1 2 3 4 5 6 32 7 8 9 10
LC-20B2UA LC-20B2UB 10 11 12 13 14 15 33 16 17 18 19
LC-20B2UA LC-20B2UB Ë DIGITAL Unit-2/5 H G F E D C B A 1 2 3 4 5 6 34 7 8 9 10
LC-20B2UA LC-20B2UB 10 11 12 13 14 15 35 16 17 18 19
LC-20B2UA LC-20B2UB Ë DIGITAL Unit-3/5 H G F E D C B A 1 2 3 4 5 6 36 7 8 9 10
LC-20B2UA LC-20B2UB 10 11 12 13 14 15 37 16 17 18 19
LC-20B2UA LC-20B2UB Ë DIGITAL Unit-4/5 H G F E D C B A 1 2 3 4 5 6 38 7 8 9 10
LC-20B2UA LC-20B2UB 10 11 12 13 14 15 39 16 17 18 19
LC-20B2UA LC-20B2UB Ë DIGITAL Unit-5/5 H G F E D C B A 1 2 3 4 5 6 40 7 8 9 10
LC-20B2UA LC-20B2UB 10 11 12 13 14 15 41 16 17 18 19
LC-20B2UA LC-20B2UB Ë ANALOG Unit-1/2 H G F E D C B A 1 2 3 4 5 6 42 7 8 9 10
LC-20B2UA LC-20B2UB 10 11 12 13 14 15 43 16 17 18 19
LC-20B2UA LC-20B2UB Ë ANALOG Unit-2/2 H G F E D C B A 1 2 3 4 5 6 44 7 8 9 10
LC-20B2UA LC-20B2UB 10 11 12 13 14 15 45 16 17 18 19
LC-20B2UA LC-20B2UB Ë INVERTER-A Unit H G F E D C B A 1 2 3 4 46 5 6
LC-20B2UA LC-20B2UB Ë INVERTER-B Unit H G F E D C B A 1 2 3 4 47 5 6
LC-20B2UA LC-20B2UB PRINTED WIRING BOARD ASSEMBLIES H G F CONTROL Unit (Side-A) E D C B A DIGITAL Unit (Side-A) 1 2 3 4 48 5 6
LC-20B2UA LC-20B2UB H G F CONTROL Unit (Side-B) E D C B A DIGITAL Unit (Side-B) 1 2 3 4 49 5 6
LC-20B2UA LC-20B2UB H G F INVERTER-A Unit (Side-A) E D C INVERTER-B Unit (Side-A) B A RC/LED Unit (Side-A) 1 2 3 4 50 5 6
LC-20B2UA LC-20B2UB H G F E D C B ANALOG Unit (Side-A) A 1 2 3 4 51 5 6
LC-20B2UA LC-20B2UB H Z1 P2003 D701 R714 P2004 C702 X2001 R7019 R7020 C7033 R7030 R7022 C7029 R1010 R1017 R1015 D1108 D1109 IC1104 C838 C1125 R1161 R1171 R1107 C1123 C1147 R1175 R1112 R1163 R1176 R1114 R1162 C1156 R1160 R1108 C1104 IC1103 R7043 R1152 B R1151 IC1105 IC1112 C7059 C7056 IC1110 R7023 FL7102 R7048 IC1113 R7042 C1139 C7025 C1110 R7003 C7055 C1142 R1183 C1138 C1135 C1137 R1184 R1117 C1134 C1112 C1114 R1191 R1186 R1190 C1136 R1193 R1185
C1112 10 R1182 R1116 C1133 C1109 11 R1115 C1111 12 C1110 SC1201 13 R1202 R1203 14 15 53 R1204 16 R1209 C1212 R1124 L1204 IC1201 R1214 R1222 R826 C1107 17 SC1203 IC1208 C1227 Q1203 C1229 C1228 IC2001 R2028 R1223 R1226 R2002 C1230 C1231 R1243 C902 R1252 R1253 R712 R1232 R2031 R1201 C835 L804 C1234 R1211 R916 C801 C809 C909 D1206 R1210 R1238 R2032 D1205 FB1203 R1208 R918 C910 L901 C1211 C1214 R1019 R2060 R917 R2061 C901 R2054 C1210 R901 R201
LC-20B2UA LC-20B2UB H D1211 D1209 R912 C903 D1212 R1250 R911 R1248 D901 R1245 R1230 R1249 Q1205 C1232 L1201 C1225 D1203 R1241 G R1246 R1240 FB901 FB902 R1239 FB903 IC901 D1210 D1204 D902 R1237 R910 Q1204 R1251 D1208 D1213 TP2005 C1233 F R914 R915 R1225 R1254 C2006 R2007 C2008 R904 R907 R909 R902 R906 R835 C804 R908 IC903 C837 D1201 TP802 C705 R919 IC702 C905 IC801 C805 R802 R814 R1221 R804 R1233 R905 C802 R811 D IC2003 R913 R801 C808
LC-20B2UA LC-20B2UB Z2 R717 R719 R716 IC703 R715 R2066 D2005 R2064 R2065 R2052 R2049 TP2001 R2043 R2003 TP2002 TP2006 R2030 Q402 TP2007 R413 TP2009 R411 R410 R409 R7037 Q7007 R7036 R7039 C7043 R7034 C7035 Q7008 R1005 Q7010 C7112 Q7005 C7702 R7033 IC1111 R7029 C7021 C7020 C7018 C7017 C7032 R7005 R1168 R7004 R1167 C7010 IC7004 C1131 R1104 C1124 R7045 C7072 IC7002 R7047 R7053 Q7003 R7007 R7010 C1146 C1105 C1132 Q7002 Q7004 R1034 R1027 R1178 C
LC-20B2UA LC-20B2UB W1 P3704 R3753 R3755 R3756 R3700 Q3700 H C3710 FH3704 FH3703 R3758 R3702 D3700 Q3701 FH3702 L3700 J3701 R3701 FH3701 C3700 D3703 R3718 C3711 C3713 R3721 R3720 FB3709 FB3706 Q3702 FB3701 G R3717 T3701 R3706 C3740 IC3701 R3704 R3759 C3704 C3702 Q3709 TU3201 R3719 R3766 R3768 R3716 D3702 C3703 R3703 R3707 C3706 R3708 R3705 C3705 C3708 D3705 R3710 R3709 R3760 R3732 D3708 C3719 R3727 R3728 R3731 R3761 C3701 D3711 Q3710 F C3707 FB3708 R3
LC-20B2UA LC-20B2UB P3602 P3601 L3700 R3605 R3757 Q3602 R3607 R3608 C3602 J3301 R3604 R3609 C3604 C3372 C3603 C3605 P3502P3501 R3901 R3600 D3601 C3607 D3600 R3602 D3602 C3606 P3500 C3601 R3603 R3601 D3605 C3600 P3503 D3603 D3703 Q3601 R3718 D3604 C3369 R3722 Q3600 D3606 C3609 Q3604 R3721 R3720 FB3709 FB3706 C3711 C3713 Q3603 R3606 C3608 FB3701 D3607 R3610 FB3700 717 FB3703 C3367 R3364 IC3305 C3370 T3701 C3368 C3714 R3349 J3404 D3301 C3329 C3360 R
LC-20B2UA LC-20B2UB H FDC4 P6702 P6701 T6704 G T6702 T6705 T6703 F C6706 C6705 E L6702 FH6700 C6707 D Q6703 Q6704 C6711 C6710 C6727 C6726 Q6707 R6706 R6704 C6709 R6709 C6712 R6708 Q6705 R6705 R6707 C6708 Q6706 FH6701 R6710 C C6713 C6714 L6704 Q6708 R6720 D6700 R6721 R6722 R6711 FH6702 FH6704 FH6705 FH6703 P6705 B INVERTER-A Unit (Chip Parts Side) A 1 2 3 4 5 6 58 7 8 9 10
LC-20B2UA LC-20B2UB FDC1 T6700 C6700 Q6700 C6725 T6701 C6702 R6700 R6701 C6703 R6702 R6703 T6702 C6701 P6700 Q6701 P6701 Q6702 L6700 C6704 10 11 12 13 14 15 59 16 17 18 19
LC-20B2UA LC-20B2UB H P6704 T6709 G C6721 C6741 R6717 L6708 P6703 C6716 C6715 C6724 Q6710 Q6709 C6717 R6713 T6706 R6712 C6719 L6706 Q6711 R6723 R6724 R6715 R6714 P6706 FH6706 FH6707 C6722 R6716 C6723 T6707 R6718 FH6709 C6718 Q6713 Q6712 E 60 6 5 4 3 2 1 Q6714 R6719 C C6740 FH6708 D6701 B C6720 F T6708 D A INVERTER-B Unit (Chip Parts Side)
LC-20B2UA LC-20B2UB H SW4008 G P4005 SW4007 D4013 R4005 D4022 D4012 R4006 R4021 C4018 SW4002 F RMC4002 SW4003 R4011 R4012 E R4024 R4029 D4014 Q4003 R4023 Q4007 D SW4004 R4030 R4031 Q4004 R4032 D4015 SW4006 C D4008 D4009 D4010 RC/LED Unit (Chip Parts Side) S4701 B P4004 A CONTROL Unit (Chip Parts Side) 1 2 3 4 61 5 6
LC-20B2UA LC-20B2UB Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code PARTS LIST LISTE DES PIECES PARTS REPLACEMENT CHANGE DES PIECES Replacement parts which have these special safety characteristics identified in this manual; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
LC-20B2UA LC-20B2UB Ref. No. ★ Part No. Description Code Ref. No.
LC-20B2UA LC-20B2UB Ref. No. Part No. ★ Description Code Ref. No.
LC-20B2UA LC-20B2UB Ref. No. Part No. ★ Description Code Ref. No.
LC-20B2UA LC-20B2UB Ref. No. Part No.
LC-20B2UA LC-20B2UB Ref. No. ★ Part No. Description Code Ref. No. Part No.
LC-20B2UA LC-20B2UB Ref. No. Part No. ★ Description Code Ref. No.
LC-20B2UA LC-20B2UB Ref. No. Part No.
LC-20B2UA LC-20B2UB Ref. No. ★ Part No. Description Code Ref. No. DUNTKB128DE03 ANALOG UNIT (Continued) J3701 QJAKE0193CEZZ P3502 QPLGN0478GEZZ P3601 QPLGN0478GEZZ P3602 QPLGN0678GEZZ P3702 QPLGN0578GEZZ P3703 QPLGN0378GEZZ P3704 QPLGN0378GEZZ SC3403 QSOCN0464FJZZ SC3405 QSOCD0456CEZZ QCNW-A267WJZZ QCNW-6059CEZZ J J J J J J J J J J J ★ Part No.
LC-20B2UA LC-20B2UB Ref. No. ★ Part No. Description Code Ref. No.
LC-20B2UA LC-20B2UB CABINET AND MECHANICAL PARTS 25 4-1 H 22 4-2 4 4-3 11 4-4 CONTROL UNIT 10 4-5 D 1-3 25 1-5 G INVERTER-A UNIT 1-9 1-6 1-12 24 1-8 1-5 21 1-3 DIGITAL UNIT D 18 1-3 1-4 1-7 1-11 F 1-6 1-9 1-12 1-11 24 INVERTER-B UNIT 1-8 E 16 24 1-10 18 1-7 17 1-4 1-3 E 13 25 25 RC/LED UNIT 9 1-1 24 1-2 8 5-4 E ANALOG UNIT 14 1 5-10 5-7 5 5-20 5-5 5-3 5-2 5-19 D 5-12 5-11 3-7 5-1 5-16 3-1 5-17 33 5-6 3 5-7 C 5-18 5-9 5-14 5-19 5-21 5-8 3-11
LC-20B2UA LC-20B2UB Ref. No. Part No. ★ Description Code Ref. No.
LC-20B2UA LC-20B2UB Ref. No. Part No. ★ Description Code Ref. No. å J J J J J RRMCG1664CESB J å TiNS-7604CEN1 J TiNS-A181WJZZ J UADP-0243CEPZ J ★ Description Code PACKING PARTS SUPPLIED ACCESSORIES LHLDW0109CESA LHLDW0109CESB QACCD3097CEPA QCNWG0003CEPA RRMCG1664CESA Part No.
LC-20B2UA LC-20B2UB PACKING OF THE SET Operation Manual (TiNS-7604CEN1(LC-20B2UA)) (TiNS-A181WJZZ(LC-20B2UB)) Cable Clamp (2 pcs.) (LHLDW0119CESA(LC-20B2UA)) (LHLDW0119CESB(LC-20B2UB)) ★ Dry Battery (2 pcs.
LC-20B2UA LC-20B2UB COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. TQ1311-S May. 2002 Printed in Japan D Japan P Japan NA.
