LC-20E1U LC-20E1UB/UW SERVICE MANUAL S72M5LC-20E1U LCD COLOR TELEVISION MODELS LC-20E1U LC-20E1UB/UW In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page » IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................... 2 » SPECIFICATIONS ......................................................
LC-20E1U LC-20E1UB/UW IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be perfomed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: ground, such as electrical conduit or electrical ground connected to an earth ground. • Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resisor.
LC-20E1U LC-20E1UB/UW PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. conduite électrique ou une prise de terre branchée à la terre. • Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension en travers de la résistance.
LC-20E1U LC-20E1UB/UW Precautions for using lead-free solder 1 Employing lead-free solder "All PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper. 2 Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder.
LC-20E1U LC-20E1UB/UW SPECIFICATIONS Items LC-20E1U Model LCD panel Number of dots Video color systems Destination TV Standard (CCIR) TV function TV Tuning System STEREO CATV 3 Dimensional Y/C separation circuit Digital comb filter Brightness Lamp life Viewing angles Audio amplifier Speakers AV1 AV2 Terminals COMPONENT Antenna Headphone OSD language Power supply Weight Accessories 19.
MAIN POWER Speaker A green indicator lights when the power is on and a red indicator lights when in the standby mode (the indicator will not light when the main power is off). Adjustable range The screen can be adjusted backwards to an angle between 12 degrees and 35 degrees. The screen cannot be set up straight. When changing the angle, make sure to hold the stand and adjust the screen to the best viewable angle. The SLEEP indicator lights up red when the SLEEP TIMER is set to on.
AUDIO R L PR PB AUDIO R ENT COMPON Y L VIDEO 2/OUT AV-IN L VIDEO 1 AV-IN AUDIO R POWER INPUT DC12V ANT. HEAD PHONE O S-VIDE 7 L VIDEO 1 AV-IN Headphones VOLUME 60 On-screen display • Headphones are not included in the supplied accessories. • No sound will be heard from the main unit speakers when a headphone mini-plug is connected into the HEADPHONE jack. POWER INPUT DC13V ANT.
DVD TUNER/BAND AUX 1 AUX 3 SURROUND ON/OFF AUX 2 L AUDIO R VIDEO 2/OUT AV-IN AUDIO R L PR PB T COMPONEN Y EO ER POW T INPUV DC13 ANT. HEAD PHONE S-VID AUDIO R L VIDEO 1 AV-IN * If your external device has an S-Video terminal, S-VIDEO connection is recommended. • Video camera • Home video game system External devices that can be connected to AV-IN1 terminal PC connection is not possible. For the cable, use a commercially available audio/video cable.
LC-20E1U LC-20E1UB/UW DIMENSIONS VOL CH MENU TV/VIDEO 2 43/64 (68) Unit: inch/(mm) MAIN POWER 1913/32 (493) 75/32 (182) 3 15/16 (100) AV-IN 1 L AUDIO R VIDEO S-VIDEO AV-IN 2/OUT L AUDIO R COMPONENT HEAD PHONE Y PB PR ANT. L AUDIO R POWER INPUT DC13V 9 2 1/64 (51.
LC-20E1U LC-20E1UB/UW REMOVING OF MAJOR PARTS 1. Remove the table stand fixing screws (4 pcs.). 2. Remove the two terminal covers. 3. Remove the terminal section fixing screws (2 pcs.). 4. Remove the cabinet B fixing screws (10 pcs.). 5. Remove the cabinet B after opening from the direction of an arrow. 6. Remove the reinforcement angle fixing screws (4 pcs.). 7. Remove the top cover fixing screws (2 pcs.). 8. Remove the control PWB fixing screws (2 pcs.). 9. Detach the connector from each PWB.
LC-20E1U LC-20E1UB/UW 10. 11. 12. 13. Remove the inverter-A PWB fixing screws (2 pcs.). Remove the inverter-B PWB fixing screws (1 pc.). Remove the digital PWB fixing screws (3 pcs.). Remove the analog PWB fixing screws (3 pcs.) and detatch the chassis frame cover fixing hooks. 14. Remove the R/C, LED PWB fixing screws (2 pcs.).
LC-20E1U LC-20E1UB/UW » Precautions in handling the LCD panels 1. Work in a clean room (with humidities below 50%). 2. Be sure to wear an anti-static armband. 3. Handle the panels on an electroconductive mat. 4. Be careful not to fall, shake and shock the panels. 15. 16. 17. 18. 19. 20. Remove the LCD panel unit fixing screws (4 pcs.). Remove the ITO earth spring fixing screw (1 pc.). Remove the reflection/deflection, prism, diffusion, ITO sheets and diffusion panel.
LC-20E1U LC-20E1UB/UW Precautions at the time of the side B(back) service of digital unit. 1. Remove only SC2001 of the FFC for connection between Digital unit(SC2001) and Analog unit(SC3403), and connect the extended cable (QCNW-A556WJZZ) for service. 2. Remove only P2004 of the Connecting Cord for connection between Digita unit(P2004) and Analog unit(P3702), and connect the extended cable (QCNW-A552WJZZ) for service. 3.
LC-20E1U LC-20E1UB/UW ADJUSTING PROCEDURE OF EACH SECTION The best adjustment is made before shipping. If any position deviation is found or after part replace is performed, adjust as follows. 1. Preparation for Adjustments (1)Use the exclusive-use AC adapter or stable DC power supply. AC adapter: UADP-0243CEPZ DC power supply: 13 ± 0.5V 2. Special mode setting procedure (1)After initialization of E2PROM the mode is changed to the adjustment mode.
LC-20E1U LC-20E1UB/UW 4. Adjustments Adjustment Adjusting conditions Adjusting method 1 B+ Adjustment (R3760) 1. Connect the DC voltmeter to pin 2 of P3702. 1. Adjust the "B+ Adj" value to 5.0±0.02V with R3760. Make exact adjustment of the 5.00V level because it will be the reference for all the other supply voltages. Be sure to make this adjustment together with the main PWB (digital PWB). During the adjustment, be also careful not to allow the voltage at pin (2) of P3702 to go above 5.3 V.
LC-20E1U LC-20E1UB/UW 5. Shipping setting list Channel ............................................................................................................................................... 2ch Air/Cable ............................................................................................................................................. Air Skip Data_CATV .................................................................................................................................
LC-20E1U LC-20E1UB/UW Test patterns in adjustment process mode [1] IC801 (Video decoder) test patterns 1-1. Getting the test patterns displayed Put the screen in AV1, AV2 or COMPONENT but keep out any signal. Call the adjustment process mode, select “TEST PATTERN” in the 3rd line of page 8, make the settings 1 thru 6, and the following test patterns show up. 1-2.
LC-20E1U LC-20E1UB/UW Pin functions of microprocessor IC (IC2001) RH-iXA300WJZZQ No.
LC-20E1U LC-20E1UB/UW Adjustment process mode menus at a glance Page Item Initial setting Function Adjust/modify Basic settings 1 MODEL INCH SIZE SYSTEM NTSC PWN FREQ PAL PWM FREQ NTSC PWM DUTY PAL PWM DUTY TV GAIN ERROR NO RESET PUBLIC MODE V-CHIP (US) CANADIAN VCHIP E1UVER E1U 20 N358 OCO OBD 0 0 OFF 0 OFF 1 OFF Model number Inch unit select Color system select Dimmer frequency setting Dimmer frequency setting Dimmer duty setting Dimmer duty setting Auto gain setting in TV mode Lamp error count & r
LC-20E1U LC-20E1UB/UW Page Item 5 6 HPF LPF EXT GEQ BAND1 EXT GEQ BAND2 EXT GEQ BAND3 EXT GEQ BAND4 EXT GEQ BAND5 TV GEQ BAND1 TV GEQ BAND2 TV GEQ BAND3 TV GEQ BAND4 TV GEQ BAND5 Initial setting Function 100 110 +1.0 –1.0 0.0 0.0 –2.0 +1.0 –1.0 0.0 0.0 –2.
LC-20E1U LC-20E1UB/UW Page Item 10 11 N358 TV LDLY N358 AV LDLY N443 AV COLOR N443 AV TINT N443 BRIGHTNESS N443 PEAKING FILTER N443 AV H-PEAKING N443 AVO START N443 SFIF N443 SCINC1 N443 AV LDLY Initial setting Function 0 0 2500 +56 +8 1 4 152 0 1623 0 Adjust/modify Y/C phase setting (TV) Y/C phase setting (composite, S video) Color density setting (composite, S video) Color tone setting (composite, S video) Brightness setting (TV, composite, S video) Peaking filter setting (TV, composite, S video) Pict
LC-20E1U LC-20E1UB/UW Page Item Initial setting Function Adjust/modify Search AFT reference settings & LCD controller settings 17 18 AFT UP AFT DOWN NTSC 01 NTSC 02 NTSC 03 NTSC 04 NTSC 05 NTSC 06 NTSC 07 NTSC 08 NTSC 09 NTSC 0A NTSC 10 NTSC 11 NTSC 12 NTSC 13 NTSC E0 NTSC E1 NTSC F0 NTSC F1 NTSC F2 NTSC F3 NTSC F4 NTSC F5 NTSC F6 NTSC F7 NTSC 14 G/A TEST PATERN PAL 01 PAL 02 PAL 03 PAL 04 PAL 05 PAL 06 PAL 07 PAL 08 PAL 09 PAL 0A PAL 10 PAL 11 PAL 12 PAL 13 PAL E0 PAL E1 PAL F0 PAL F1 PAL F2 PAL F3 PA
LC-20E1U LC-20E1UB/UW Page Item Initial setting Function Adjust/modify Gradation & COM settings 19 20 V255 V255 BIAS V235 V235 BIAS V176 V176 BIAS V112 V112 BIAS V64 V64 BIAS V32 V32 BIAS V21 V21 BIAS V17 V17 BIAS V7 V7 BIAS V0 V0 BIAS VGL ADJ VGL COM COM G/A READDATA G/A READDATA 255 127 222 127 130 150 96 170 65 40 72 100 45 50 52 145 27 65 0 80 27 215 179 00 00 WAIT Gradation power reference voltage Gradation power reference voltage Gradation power reference voltage Gradation power reference volta
LC-20E1U LC-20E1UB/UW PUBLIC MODE 1. Outline The Public mode is designed to limit the functions of LCD TV sets that are set up at hotels, public places (hospitals, for example), shop fronts and similar locations. Note: In the Public mode, some user settings may fail to be changed later. The Closed Caption, V-Chip, MTS and some other functions, as well as the volume control must be preset before getting the TV set into the Public mode. 2. Setting procedure Take the following steps to go to the Public mode.
LC-20E1U LC-20E1UB/UW Item MAXIMUM VOLUME 60 Default 1~60 Setting VOLUME FIXED VARIABLE VARIABLE FIXED REMOTE CONTROL RESPOND RESPOND NO RESPOND USER CONTROL RESPOND RESPOND NO RESPOND ON SCREEN DISPLAY YES AV1 INPUT NORMAL YES NO NORMAL START Function Sets the highest sound volume level. (The volume level is expressed in digital form only.) Makes the sound volume adjustable. Keeps the sound volume fixed. (The sound volume is fixed at the then level.
Check IC801 and its peripheral circuits. Check the IC801 signal input line. No Check the related lines, IC801 itself and its peripheral circuits. Are the waveforms at pins (10), (11), (13), (15) and (17) of IC1201 as specified? Yes No No Check IC1201 and its peripheral circuits as well as the LCD panel voltage and waveform. Check the IC801 signal output line, IC801 itself and its peripheral circuits.
No TV output 27 Are inputs and outputs of IC801 as specified? Yes No Check IC402 and its peripheral parts. Check IC801 and its peripheral circuits. Does the video decoder No test pattern appear? Yes Check IC1201, its peripheral circuits and the LCD panel. Does the LCD controller test No pattern appear? No Check IC402 and its peripheral parts.
No No No VIDEO color Check J3701, its peripheral parts and connection cable. Yes Is any of T3701’s primary No side, Q3700 and S4701 shortcircuited? Yes Disconnect F3701and F3702. Is the load side short-circuited? Check all the settings on the microprocessor’s adjust process menu. No TV color No color Check the secondary-side load of T3701.
No sound from headphone 29 Check the speakers and their peripheral parts. Yes Are inputs at pins (2) and (4) as well as outputs at pins (8) and (12), all of IC3305, as specified? Yes Are outputs at pins (1) and (7) of IC3301/ IC3303 as specified? Yes Are input and output of IC3304 as specified? Yes Is pin (53) of IC2001 at “L”? No No No No Check the line in question, IC3301 and its peripheral parts. Check IC3301, IC3303 and their peripheral parts. Check IC3304 and its peripheral parts.
LC-20E1U LC-20E1UB/UW CHASSIS LAYOUT INVBERTER-A Unit CONTROL Unit H DIGITAL Unit G F E ANALOG Unit D INVBERTER-B Unit C B R/C, LED Unit A 1 2 3 30 4 5 6 7 8 9 10 11 31 12
LC-20E1U LC-20E1UB/UW BLOCK DIAGRAM H TUNER TU3201 TV-V SYOUT, SCOUT SIF SIF-AMP. Q3201 Q3202 AUDIO IN/OUT SWITCH IC3501 Q3500 L2, R2 F SY, SC TV-V V1 V2 V2 VIDEO IN/OUT SWITCH Q3501-Q3505 VIDEO SWITCH IC402 AV1 V V1SY VOUT DL, DR DY LCD PANEL AUDIO FILTER IC3301 IC3303 SYNC SEPARATER.
LC-20E1U LC-20E1UB/UW OVERALL WIRING DIAGRAM H G F E D C B A 1 2 3 34 4 5 6 7 8 9 10 11 35 12
LC-20E1U LC-20E1UB/UW DESCRIPTION OF SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: 1. The voltages at test points are measured on exclusive AC adaptor and the stble supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. INDICATION OF RESISTOR & CAPACITOR: RESISTOR 1. The unit of resistance “Ω” is omitted. (K=kΩ=1000 Ω, M=MΩ). 2. All resistors are ± 5%, unless otherwise noted.
LC-20E1U LC-20E1UB/UW SCHEMATIC DIAGRAM H ËR/C, LED and CONTROL Unit R/C, LED G F E D C B A 1 2 3 4 37 5 6
LC-20E1U LC-20E1UB/UW Ë DIGITAL Unit-1/5 H G F E D C B A 1 2 3 38 4 5 6 7 8 9 10 11 39 12
LC-20E1U LC-20E1UB/UW Ë DIGITAL Unit-2/5 H G F E D C B A 1 2 3 40 4 5 6 7 8 9 10 11 41 12
LC-20E1U LC-20E1UB/UW Ë DIGITAL Unit-3/5 H G F E D C B A 1 2 3 42 4 5 6 7 8 9 10 11 43 12
LC-20E1U LC-20E1UB/UW Ë DIGITAL Unit-4/5 H G F E D C B A 1 2 3 44 4 5 6 7 8 9 10 11 45 12
LC-20E1U LC-20E1UB/UW Ë DIGITAL Unit-5/5 H G F E D C B A 1 2 3 46 4 5 6 7 8 9 10 11 47 12
LC-20E1U LC-20E1UB/UW Ë ANALOG Unit-1/2 H G F E D C B A 1 2 3 48 4 5 6 7 8 9 10 11 49 12
LC-20E1U LC-20E1UB/UW Ë ANALOG Unit-2/2 H G F E D C B A 1 2 3 50 4 5 6 7 8 9 10 11 51 12
LC-20E1U LC-20E1UB/UW Ë INVERTER-A Unit H G F E D C B A 1 2 3 4 52 5 6
LC-20E1U LC-20E1UB/UW Ë INVERTER-B Unit H G F E D C B A 1 2 3 4 53 5 6
LC-20E1U LC-20E1UB/UW PRINTED WIRING BOARD ASSEMBLIES H G F E D C B A DIGITAL Unit (Side-A) 1 2 3 4 54 5 6
LC-20E1U LC-20E1UB/UW H R422 FL7004 C7122 C7054 FB7004 C7048 C7025 D7701 C2020 C7024 FB7003 C7047 SC2001 R7203 C7204 C7205 D701 R415 C409 C408 R414 C7104 C414 R419 L402 C413 R416 C411 IC402 D2002 C702 R7202 R7201 FL401 R424 C410 R7112 D2003 C2021 FB7105 C7123 R7012 C7113 R7043 R7042 R7048 C7055 C7027 C412 C703 C7201 C7202 FL7003 C7031 Q7001 C7059 R425 R7204 R423 C7005 R7003 Q403 IC7202 C7036 C7015 IC7001 R418 L401 R7051 R7052 C7203 C7053 G
LC-20E1U LC-20E1UB/UW H G F E D C B A DIGITAL Unit (Side-B) 1 2 3 4 56 5 6
1 D1203 D1204 D1213 R1241 2 IC1207 D1212 Q1201 R833 C831 R834 R832 C832 C830 C807 3 57 C822 C827 C823 C837 R906 IC903 R802 C836 C1225 R814 R1221 4 R2012 C820 C819 C1154 D1101 R1130 IC801 IC1206 R1104 R1121 R1123 Q1102 R1147 R1255 C1224 C1223 5 IC1107 C1124 R1032 IC1108 C1146 IC1114 R1034 R1027 IC1115 R1174 R1177 R1122 C1119 C1108 C2006 R403 C1131 C1143 C7085 R7049 IC7004 C1102 R1198 IC1106 R1028 C1132 Q7003 Q7004 R1167 R7009 R1168 C7026 C1105 C
LC-20E1U LC-20E1UB/UW H G C4018 R4023 Q4004 Q4003 Q4007 R4024 D4014 R4029 R4031 F D4013 P4005 D4012 R4030 D4022 R4021 R/C, LED Unit (Side-A) R4032 D4015 R/C, LED Unit (Chip Parts Side-A) E D CONTROL Unit (Side-A) (QPWBSB413WJZZ) D4010 B D4009 D4008 P4004 SW4006 SW4004 R4012 SW4003 SW4002 R4006 SW4007 SW4008 R4005 R4011 C CONTROL Unit (Chip Parts Side-A) (QPWBSB413WJZZ) A 1 2 3 4 58 5 6
LC-20E1U LC-20E1UB/UW H G F E D C B A ANALOG Unit (Side-A) 1 2 3 4 59 5 6
LC-20E1U LC-20E1UB/UW W1 P3602 P3704 D3602 D3601 C3607 D3600 R3605 C3606 R3757 Q3602 C3603 R3702 C3605 R3604 R3609 R3758 D3700 Q3701 F3702-1 C3710 R3701 R3600 R3602 R3700 Q3700 R3756 P3502 P3501 R3901 R3753 R3755 H P3500 P3601 R3608 R3607 C3602 C3604 C3700 C3601 D3605 P3503 D3606 C3600 R3718 R3722 Q3600 C3609 D3604 D3607 Q3604 R3721 R3720 FB3709 FB3706 Q3702 C3711 C3713 Q3603 R3606 C3608 FB3701 G R3603 R3601 D3603 D3703 Q3601 D3608 R3610 FB3700
LC-20E1U LC-20E1UB/UW H G F E D C B A INVERTER-A Unit (Side-A) 1 2 3 4 62 5 6
LC-20E1U LC-20E1UB/UW R6708 C6712 H Q6706 R6709 C6713 R6710 Q6708 T6705 Q6707 P6702 R6711 R6722 P6705 D6700 Q6704 R6721 G R6705 R6720 R6706 R6707 C6708 Q6705 Q6703 T6704 C6707 R6704 F T6703 P6701 E T6702 R6703 R6702 C6703 R6701 Q6702 D Q6701 R6700 Q6700 C6702 C P6700 T6701 B T6700 A INVERTER-A Unit (Chip Parts Side-A) 1 2 3 4 63 5 6
LC-20E1U LC-20E1UB/UW H G F E D C B INVERTER-B Unit (Side-A) A 1 2 3 4 64 5 6
LC-20E1U LC-20E1UB/UW H P6704 G T6709 T6708 F Q6713 Q6712 C6722 R6717 R6716 E P6703 C6723 R6718 R6719 D T6707 Q6714 C6717 R6713 R6712 Q6711 D6701 Q6710 Q6709 R6723 R6724 C T6706 C6718 P6706 R6715 R6714 B INVERTER-B Unit (Chip Parts Side-A) A 1 2 3 4 65 5 6
LC-20E1U LC-20E1UB/UW Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code PARTS LIST LISTE DES PIECES PARTS REPLACEMENT CHANGE DES PIECES Replacement parts which have these special safety characteristics identified in this manual; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
LC-20E1U LC-20E1UB/UW Ref. No. ★ Part No. Description Ref. No.
LC-20E1U LC-20E1UB/UW Ref. No. Part No. ★ Description Code Ref. No.
LC-20E1U LC-20E1UB/UW Ref. No. ★ Part No. Description Code Ref. No.
LC-20E1U LC-20E1UB/UW Ref. No. Part No. ★ Description Code Ref. No. Part No.
LC-20E1U LC-20E1UB/UW Ref. No. R7701 R7702 R7703 R7704 R7705 Part No. ★ Description Code Ref. No. ★ Part No. Description DUNTKA670FE29 DUNTKB412DE03 DIGITAL UNIT (Continued) ANALOG UNIT VRS-CY1JF103JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CE3AF4R7JY J J J J J 10k 3.3k 3.3k 1k 4.7 1/16W 1/16W 1/16W 1/16W 1W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide TUNER AA AA AA AA AC NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY.
LC-20E1U LC-20E1UB/UW Ref. No. ★ Part No. Description Code Ref. No.
LC-20E1U LC-20E1UB/UW Ref. No. Part No. ★ Description Code Ref. No.
LC-20E1U LC-20E1UB/UW Ref. No. R3752 R3753 R3754 R3759 R3761 R3762 R3766 R3901 R3902 Part No. ★ Description Code Ref. No. Description DUNTKB413DE03 DUNTKB413DE03 ANALOG UNIT (Continued) CONTROL UNIT VRS-CY1JF102JY VRS-TX2HF000JY VRS-CY1JF103JY VRS-TW2ED102JY VRS-CY1JF272JY VRS-TW2ED561JY VRS-CY1JF472JY VRS-TQ2BD000JY VRS-TQ2BD000JY J J J J J J J J J 1k 0 10k 1k 2.7k 560 4.
LC-20E1U LC-20E1UB/UW Ref. No. ★ Part No. Description Code Ref. No. DUNTKB416DE01 R/C, LED UNIT INVERTER-A UNIT TRANSISTORS RH-EX1271CEZZY RH-EX1271CEZZY RH-PX0421CEZZY RH-PX0421CEZZY RH-EX1271CEZZY J J J J J Q6700 Q6701 Q6702 Q6703 Q6704 Q6705 Q6706 Q6707 Q6708 Zener Diode, 12V Zener Diode, 12V POWER Indicator SLEEP Indicator Zener Diode, 12V AB AB AD AD AB J 1 D6700 VHDiMN10///-1Y 10V Ceramic J J J J J 100 4.7k 470 4.7k 4.
LC-20E1U LC-20E1UB/UW Ref. No. ★ Part No. Description Code Ref. No.
LC-20E1U LC-20E1UB/UW CABINET AND MECHANICAL PARTS H 22 18 4-1 4-2 4 10 4-3 4-5 4-4 4-7 4-8 4-6 Control PWB G Inverter-A PWB 22 K 20 1-12 1-13 K 1-5 1-6 1-7 Digital PWB 12 D 1-6 1-7 L 1-6 1-4 I Inverter-B PWB 11 J 20 H 1-8 F 20 1-11 L 1-10 22 C D 17 1-9 R/C, LED PWB 1-13 20 1-2 1-3 1-8 1-6 21 6 1-7 1-6 13 1-5 1-12 1-4 1-1 H 14 1-6 1-7 Analog PWB 7 G E 5-20 5-10 B 1 B 5-11 5-7 5-2 5 5-3 5-4 D 5-9 3-2 5-20 5-19 5-12 5-5 16 A 5-6 5-1 5-19 5-1
LC-20E1U LC-20E1UB/UW Ref. No. ★ Part No. Description Code Ref. No.
LC-20E1U LC-20E1UB/UW PACKING OF THE SET ★ Operation Manual (TiNS-A158WJZZ) Cable Clamp (LHLDW0109CESA : LC-20E1U/UW) (LHLDW0109CESB : LC-20E1UB) ★ "AAA" size Battery (2pcs) Polyethylene Bag (SSAKA0160CEZZ) ★ Buffer Material (Top) (SPAKFA014WJZZ) ★ Wrapping Paper (SPAKPA077WJZZ) ★ Buffer Material (Partition) (SPAKFA093WJZZ) AC Cord (QACCD3097CEPA) Antenna Cable (QCNWG0003CEPA) Infrared R/C Unit (RRMCGA077WJSA : LC-20E1U) (RRMCGA077WJSB : LC-20E1UB) (RRMCGA077WJSC : LC-20E1UW) AC Adapter (UADP-02
LC-20E1U LC-20E1UB/UW COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. TQ1390-S Sep. 2002 Printed in Japan D Japan P Japan MI.
