SERVICE MANUAL S38OHLC26DV24 LCD COLOR TELEVISION/ DVD VIDEO PLAYER MODEL LC-26DV24U In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS • • • • • • • • • • • • • • • • • • • • • CAUTION .............................................................................................................................. IMPORTANT SAFEGUARDS .................
CAUTION THIS LCD COLOR TELEVISION EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS LASER RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.
IMPORTANT SAFEGUARDS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
IMPORTANT SAFEGUARDS (CONTINUED) 19) If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, conne
IMPORTANT SAFEGUARDS (CONTINUED) 25) Do not allow the product to output distorted sound for an extended period of time. It may cause speaker overheating and fire. 26) When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage. 27) Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the laser beam. It may cause eye damage.
WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD MT PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector. NOTE • Before your operation, please read “PREPARATION OF SERVICING”. • Use the Lead Free solder.
DISC REMOVAL METHOD AT NO POWER SUPPLY 1. Remove the Back Cabinet and Angle Deck. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) 2. Slide the Belt Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1) 3. Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc. DVD Deck Belt Loading Fig.
ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.) Caution: • Pb free solder has a higher melting point than standard solder; Typically the melting point is 86°F~104°F(30°C~40°C) higher. Please use a soldering iron with temperature control and adjust it to 650°F ± 20°F (350°C ± 10°C). In case of using high temperature soldering iron, please be careful not to heat too long.
GENERAL SPECIFICATIONS G-1 TV System LCD LCD Size / Visual Size LCD Type Number of Pixels View Range Left/Right Up/Down Bright Dot Zero Bright Dot Ratio Color System Speaker Position Size Impedance Max 10%(Typical) Sound Output G-2 DVD System Color System Disc Disc Diameter Drive Search speed Fwd Actual Rev Actual Slow speed Fwd Actual Rev Actual G-3 Tuning System Broadcasting System Tuner and Receive CH Intermediate Frequency G-4 Signal Analog Digital System Destination CH Coverage 2~69,
GENERAL SPECIFICATIONS G-5 Power Power Source AC DC Power Consumption Protector G-6 Regulation at AC at DC Stand by (at AC) Energy Star Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Safety Radiation Laser Operation Storage G-7 Temperature G-8 G-9 Operating Humidity Clock and Clock Timer Sleep Timer Max Time On Timer Program Off Timer Program Game Timer Wake Up Timer Timer Back-up (at Power Off Mode) Remote Unit Control Glow in Dark Remocon Remocon Format Format Custom Code Power So
GENERAL SPECIFICATIONS UP DOWN SETUP/TV MENU EXIT/CANCEL RETURN ･/SUBTITLE TV/DVD OPEN/CLOSE(EJECT) FWD(SEARCH+) REV(SEARCH-) SKIP+ SKIPPAUSE/STILL PLAY STOP PLAY MODE ANGLE ZOOM DVD MENU TOP MENU REPEAT A-B MARKER DIRECT SKIP(JUMP) FREEZE G-11 Features (TV) Auto Shut Off Auto Search Power On Memory Comb Filter Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes No Yes Yes 3 -D Game Position Auto Setup(Language/CH Program) Picture Setting(TV) AV Mode(Pictur
GENERAL SPECIFICATIONS V-Chip Type RRT Setup Lock Hotel Lock Channel Lock Video Lock Panel Lock Menu Language Closed Caption CC Advanced View Mode (Picture Size) Picture Scroll Film Mode Aspect Backlight PFC(Power Factor circuit) Freeze frame PIP/POP Direct Input Selection Digital Out Dolby Digital MPEG PCM DTS PC Monitor Input VGA (640x480) VGA (720x400) WVGA (848x480) SVGA (800x600) XGA (1024x768) WXGA (1280x768) WXGA (1280x720) WXGA (1360x768) SXGA (1280x1024) HDMI Input VGA (640x480) 720x480i (4:3) 72
GENERAL SPECIFICATIONS Component Input Wall Mount Features (DVD) Video CD Playback SVCD Playback MP3 Playback JPEG WMA Digital Out Down Mix Out Closed Caption Screen Saver TV Screen G-12 Accessories Audio DAC Owner's Manual 720x480i (4:3) 720x480i (16:9) 720x480p (4:3) 720x480p (16:9) 720x576i (4:3) 720x576i (16:9) 720x576p (4:3) 720x576p (16:9) 1280x720p 1920x1080i Size W x H(mm) Screw Size (Dolby Digital) (MPEG) (PCM) (DTS) (Dolby Digital) (DTS) 4:3 (Letter Box⁄Pan Scan) 16:9 (Wide) Language w/Gu
GENERAL SPECIFICATIONS G-13 Interface AV Cord (2Pin-1Pin) Registration Card (NDL Card) 300 to 75ohm Antenna Adapter Sheet Information (Return) Sheet Information (HDMI) Cleaning Cloth Switch Top Power (Tact) Channel Up Channel Down Volume Up Volume Down Menu Play Eject Skip+, Search+ Skip-, SearchStill/Pause Stop Main Power SW Input Select Rear Main Power SW Indicator Power/Stand-By Power Wake Up On Timer Terminals Side Video Input 1 Audio Input 1 S - Input 1 Video Input 2 Audio Input 2 S - Input 2 Video
GENERAL SPECIFICATIONS G-14 Set Size Approx. W x D x H (mm) w/o Handle, Stand Approx. W x D x H (mm) G-15 Weight G-16 Carton G-17 Material G-18 Environment Net (Approx.) Net w/o Handle, Stand (Approx.) Gross (Approx.
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS (4)(4) (2) (4)(4) 1-1: BACK CABINET (Refer to Fig. 1-1) 1. Remove the 14 screws (1). 2. Remove the 7 screws (2). 3. Remove the Back Cabinet in the direction of arrow. DVD MT PCB (1)(2) (1) DVD Deck Pick Up PCB (B) (C) (3) (A) (3) (1)(2) (2) (2) (1) (2) (1) (1) (5) Angle MPEG (1) (1) (2) (5) Angle DVD-1 (1) (2) (2) Short circuit using a soldering iron. (1) (1) (1) (1) (1) (1) (1) (D) Back Cabinet Fig.
DISASSEMBLY INSTRUCTIONS 1-4: REMOCON PCB (Refer to Fig. 1-4) 1. Disconnect the following connector: (CP4201). 2. Remove the 2 screws (1). 3. Remove the Remocon PCB in the direction of arrow (A). (3) (2) (1) (5) (5)(5) (5) (5) (4) (2) Shield Digital (A) Plate Jack (1)(1) Digital PCB Remocon PCB (B) (A) Fig. 1-4 1-5: LCD BLOCK (Refer to Fig. 1-5) Fig. 1-6 1. Disconnect the following connectors: (CP302, CP2804 and CP4303). 2. Remove the Holder Panel. 3. Remove the 4 screws (1). 4.
DISASSEMBLY INSTRUCTIONS 2-2: SWITCH PCB ASS'Y/GEAR MIDDLE/GEAR FEED/RACK FEED ASS'Y/FEED MOTOR (Refer to Fig. 2-2-A) 2. REMOVAL OF DVD DECK PARTS NOTE 1. Remove the Insulator (F). 2. Remove the Insulator (R). 3. Unlock the support 1. 4. Remove the Gear Middle. 5. Remove the screw 2. 6. Remove the Rack Feed Ass'y. 7. Remove the screw 3. 8. Remove the Switch PCB Ass'y. 9. Remove the screw 4. 10. Remove the Gear Feed. 11. Remove the 2 screws 5. 12. Remove the Feed Motor. 13. Remove the Gear Motor. 1.
DISASSEMBLY INSTRUCTIONS [ 6 pin FFC ] Gear Motor 40 ± 1mm Fold 8.0 ± 0.2mm Feed Motor Fold 60 ± 1mm Safety surface for pressing of the insert. Fig. 2-2-C Fig. 2-3-B Switch PCB Ass'y ~ FEED MOTOR ~ WHITE (4) BROWN (3) • Install wire from (1) to (4) in order. ~ SPINDLE MOTOR ~ YELLOW (2) GREEN (1) Fig. 2-2-D Traverse Ass'y Check Hook Check Hook Check Hook Check Hook • Loosen the wire in the direction of the arrow. Fig. 2-2-E 2-3: FFC WIRE HANDLING 1.
DISASSEMBLY INSTRUCTIONS 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 3-3.) 3. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC REMOVAL NOTE 1. Put Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 3-1.
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 3-8.) 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 3-5.) Thin-tip Soldering Iron IC Soldering Iron Fig. 3-8 5.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition. (See below chart.) Set Condition Set Key Remocon Key Standard Time TV mode VOL. DOWN (Minimum) 0 2 sec. Releasing of V-CHIP PASSWORD. TV mode VOL. DOWN (Minimum) 1 2 sec.
SERVICING FIXTURES AND TOOLS JG176 Up-Date Disc Ref. No. JG176 2007 USA DTV LCD Rom Disc Part No. Parts Name Remarks JG176 APJG176123 Up-Date Disc Up-Date of the Firmware JG176 APJG176126 2007 USA DTV LCD Rom Disc Up-Date of the Firmware RE-WRITE FOR DVD FIRMWARE 1. Turn on the power, and set the DVD mode. 2. Confirm that the “No Disc” will be appeared on the screen. 3. Press both VOL. DOWN button on the set and Channel button (5) on the remote control for more than 2 seconds. 4. Press VOL.
RE-WRITE FOR DIGITAL SOFT FIRMWARE 1. Copy the "update.dat" in CD to USB Flash Memory. Recommended USB Flash Memory • SanDisk Cruzer Mini USB Flash Drive 128Mb • SanDisk Cruzer Mini USB Flash Drive 256Mb • SanDisk Cruzer Micoro USB Flash Drive 128Mb • SanDisk Cruzer Micoro USB Flash Drive 256Mb • TwinMos ModileDisk3 128Mb (USB 2.0) • TwinMos ModileDisk3 256Mb (USB 2.0) NOTE: After Format is done with FAT32 File system beforehand, USB Flash Memory is used. The computer of WINDOWS2000 is used. 2.
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding. 1. Turn on the POWER, and set to the TV mode. 2. Set the VOLUME to minimum. 3. Press both VOL.
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE NO. 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 29 30 Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION • Use an isolation transformer when performing any service on this chassis. • When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position.
ELECTRICAL ADJUSTMENTS 2-2: BRIGHT CENT 2-3: CONTRAST MAX 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (32) on the remote control to select "BRIGHTNESS CENT". 4. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "121". 5. Check if the picture is normal. 6. Receive the monoscope pattern. (VIDEO Input) 7.
ELECTRICAL ADJUSTMENTS 2-4: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (TV/AV/COMPONENT/HDMI/DVD/PC/DTV) COMPONENT AV FUNCTION NO. TV Step No. HDMI PC Y/C Step No. Step No. - DTV DVD GAME CVBS 480i/576i 480p/576p 720p 1080i 480i/576i 480p/576p 720p 1080i VGA 640x480 1280x720 Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No.
ELECTRICAL ADJUSTMENTS 3.
TROUBLESHOOTING GUIDE (LCD SECTION) POWER DOES NOT TURN ON Is F401 broken? Yes Change F401. No Is there voltage at pin 1 of IC402 6V? No Check IC402 and peripheral circuit. Yes Is R412 broken? Yes Change R412. No Is there voltage at pin 10 of IC401 19V? No Check IC401 and peripheral circuit. Yes Change DIGITAL PCB.
TROUBLESHOOTING GUIDE THE PICTURE APPEARS, BUT THE AUDIO DOES NOT APPEARS. (AT RF MODE) Is CP302 connected? No Connect CP302. Yes Is there signal at pins 1 and 4 of CP302? Yes Change SP301 and SP302. No Is there signal at pins 2 and 5 of IC302? Yes Check IC302 and peripheral circuit. No Is there signal at pins AA3 and AA4 of IC2801? Yes Check Connection of CP4302. No Is there signal at pins 1 and 2 of IC6551? Yes Check IC6551 and peripheral circuit.
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR No Does backlight shine? Is there voltage at pins 1, 2, 3, 4 and 5 of CP406 24V? No Check IC401, T401, D437 and peripheral circuit. Yes Yes No Connected CD2804. Is CD2804 connected? Yes Is there voltage at pins 1, 2, 3, 4 and 5 of CP2804 5V? No Check IC407 and peripheral circuit. Yes Is there signal at pins 13, 14, 16, 17, 19, 20, 22, 23, 25 and 26 of CP2804? Yes Change V2301 (PANEL). No Change DIGITAL PCB.
TROUBLESHOOTING GUIDE THE COLOR DOES NOT APPEAR Is setting of color normal? No Adjust the color. Yes Is the color signal received? No Receive the color signal. Yes Is there color signal at IC2801? No Check IC2801 and peripheral circuit. Yes Change DIGITAL PCB.
TROUBLESHOOTING GUIDE (DVD SECTION) DOES NOT DISPLAY DVD PICTURE Does this display logo picture? Yes Check the disc. No Is there signal at pins 149 and 151 of IC4001? Yes Check pins 8 and 10 of CP8501 and peripheral circuit. No Does IC4001 gets P.CON+3.3V and P.CON+1.8V? Yes Change IC4001. No Check P.CON+3.3V and P.CON+1.8V line.
TROUBLESHOOTING GUIDE DISC DOES NOT EJECT Does OSD appear on the screen? No Is remote key set effectively? No Check pins J18 and J19 of IC2801 and peripheral circuit. No Check IC4001 and peripheral circuit. Yes Yes Check pins 138 and 139 of IC4001 and peripheral circuit. Does this eject disc at change DVD DECK? Yes Change DVD DECK. No Is there signal at pins 4 and 5 of CP2302? Yes Is there signal at pins 1 and 2 of CP2302? Yes Change IC4001. E-6 No Change IC2301.
TROUBLESHOOTING GUIDE DOES NOT PLAY DVD Change DVD DECK. No Does this display "INCORRECT DISC"? Yes No Does CD2001 connect with CP2301 correctly? No Connect CD2001. Does this display reading mark? No Change IC4001. Yes No Does disc rotate? Change DVD DECK. Yes Change IC4001. E-7 Yes Is the voltage between JG017 and JG018 less than 0.
TROUBLESHOOTING GUIDE DOES NOT PLAY CD Change DVD DECK. No Does this display "INCORRECT DISC"? Yes No Does CD2001 connect with CP2301 correctly? No Connect CD2001. Does this display reading mark? No Change IC4001. Yes No Does disc rotate? Change DVD DECK. Yes Change IC4001. E-8 Yes Is the voltage between JG019 and JG018 less than 0.
TROUBLESHOOTING GUIDE NO SOUND DVD/CD ANALOG AUDIO Is there signal at pins 113, 114, 115 and 116 of IC4001? No Change IC4001. Yes Is there signal at pins 1 and 7 of IC8501? No Check pins 1 and 7 of IC8501 and peripheral circuit. Yes No Connected CD8501. Does CD8501 connected? Yes Change DIGITAL PCB. NO SOUND DVD/CD DIGITAL AUDIO Is there signal at pin1 of CP8501? Yes Change DIGITAL PCB. No Is there signal at pin122 of IC4001? Yes Check line circuit IC4001 to CP8501. No Change IC4001.
DVD BLOCK DIAGRAM DVD LOADER DSM2 LCD BLOCK DUPRD1 MD_DVD, MD_CD DUPTD1 RF, A, B, C, D, E, F TIN_SW OPU DVD_CD, DVD_LD, CD_LD SPINDLE/ STEPING/ SLED MOTOR TR+/-, FO+/-, MOT_LD+/-, MOT_SLED+/MOT_SPDL+/- Motor Drive IC2301 LA6565VR-TLM-E SPINDLE/SLED/ FOCUS/TRACK_PWM, TRAY_CLOSE/OPEN SPDIF MPEG/MICON/DSP/RF_AMP IC4001 ZR36966ELCG-D DAC_VIDEO_C/D DAC_VIDEO_A RESET SYS_MUTE SPDL_SENS+/- HOME, TIN_SW, TOUT_SW APWM_L+/-, APWM_R+/- AUDIO AMP IC8501 NJM4565M(TE1) DVD_AUDIO_L DVD_AUDIO_R TX RX STAR
POWER BLOCK DIAGRAM L402 L401 CD3805 F401 AC IN D415 1 2 1 2 3 4 3 4 J401 TRANSFORMER T402 1 + Q409 9 C455 8 3 CP401__7.8. AT+5V 7 Q416 5 C403 + C404 + D Vcc 5 4 Q417 1 FEED BACK IC410 PS2561AL1-1-V(W) POWER SW IC401 MP3A5038 Q2g Vcc Q1d FB P.GNDVW Q2d 20 10 18 13 8 15 22 23 SW REGULATOR IC404 KIA431A-AT FB Vdd 2 CP401__2. POWER FAIL SW POWER SW IC402 MIP2F4 D407 D405 CP401__1.TUNER+30V VccS 4 1 3 2 4 1 3 2 1 CP401__6.P.CON+5V CP401__3.
POWER(DIGITAL PCB) BLOCK DIAGRAM CP3001 1 TUNER+30V 2 3 4 5 6 7 8 9 10 POWER FAIL SYS_POWER_H AT+3.3V GND P.
SIGNAL BLOCK DIAGRAM AUDIO OUT J4301 AV3-13P2-60S1 OUT ANALOG AUDIO OUT L/R SPDIF COAXIAL IN S VIDEO IN J4202 DIN-409B SPEAKER L/R SP301, SP302 S0412F06 S1 Y S1 C AMP L/R AUDIO L/R SOUND AMP IC IC302 AN17808B COMPONENT Y IN IN COMPONENT IN J4203 AV3-13P2-31S1 HDMI IN 1 CP3601 5-1903015-4 COMPONENT U COMPONENT V HDMI 1 HDMI SW IC IC3603 STHDMI002ABTR HDMI LCD PANEL V2301 V260B1-L01 LVDS DATA/CLK DIGITAL RF (IF) IN TUNER TU5801 ENG36E19KF ANALOG RF(CVBS) SIF BTSC DEMODULATOR IC IC5801 AN
PRINTED CIRCUIT BOARDS DVD MT (BOTTOM SIDE) DVD MT (TOP SIDE) NTSC PAL DMG097A C8542 CP8501 4 R8516 R2306 R2318 R2341 R2340 Q2302 Q2301 C2335 C2333 DMG097A C4064 C4062 C4010 IC4007 W860 R4040 C4091 C4021 C4039 C4060 C4008 C4006 R4067 D4003 D4002 R4036 R4037 R4038 R4045 R4078 R4089 C4027 R4052 R4065 R4087 R4032 C4081 C4095 C4096 C8511 C4105 W818 C8520 L8504 R8526 R2338 L8502 R8539 B8503 R8535 R8536 C8543 C8537 C8536 C4028 C4079 C4032 R4024 R4014 C4049 C4040 W841 R
PRINTED CIRCUIT BOARDS DIGITAL (TOP SIDE) C6560 C6556 C6202 L6551 SH3004 R6201 D6201 C6201 R6202 C6561 C6562 R6560 C6555 B6552 C6559 B6553 B4303 B4305 B4306 B4302 B4304 W828 W827 SH3003 CP6202 SH3005 CP4301 D6202 C5819 C5833 C6553 TU5801 C5825 C4329 R4322 C4339 B2813 B2815 NR2806 C4321 B4313 J4301 L3602 CP4303 C3401 R3413 R3412 R3405 Q3404 C3036 CP3601 L3601 R3639 R3640 R3606 R3605 C3601 D3605 Q3608 W826 PC Q3406 Q3405 R3631 Q3402 Q3607 D3401 L3401 Q340
R4304 Q3408 R4305 R3431 Q3403 Q3401Q3412 R3433 R3432 R2807 C3416 R3426 C3415 R3425 B2801 B2803 B2804 B2809 B2807 B2806 CEG352A IC3004 B2805 D6205 IC6201 R6204 R6209 W813 R6210 R6212 R6211 C2814 C2816 R3013 R3017 R3015 C3018 C2839 1 9 R2809 17 W858 W857R3010 R6231 R6226 C6218 C2872 C2871 C2879 R2836 C2822 R2819 R2818 C2821 L5801 R3007 C5814 IC5801 C5823 C6567 R6552 IC6556 C5805 B5802 C6563 C6566 R6561 R6559 R6572 R6562 R6558 R6573 C6557 C6568 C6565 R6220 R6222 C6571 C65
C430 C493_1 C455_1 D415 W021 C403_1 D405 C423 R429 R416 R536 W043 R428 R436 HS302 W020 R4224 J4203 D444 D401 R475 R503 R477 R478 R438 C494_1 IC410 D433 IC408 IC406 IC405 C431_1 R473 J4206 R4236 W022 W883 W885 W884 C441_1 D445 R490 C462_1 W063 C438_1 C434_1 C6513_1 W064 J4202 C6509_1 R452 W048 D416 C444 W009 C453 L413 R445 R501 J4205 SH406 W058 C435_1 L411 W037 D443 IC407 W011 C440_1 D442 C442_1 D413 W046 W887 C433_1 HS405 L404 W024 C461 C
G-9 D421 Q307 Q403 R463 R420 R508 R4279 R4283 R4280 R521 C479 C477 C476 R405 C471 R408 C470 R418 R407 R465 C472 IC412 C456 C488 C454 C452 C487 C489 C490 CEG358A C358 Q404 C2251 R2207_2 C2203 R2214 R336 R337 R439 R2212 R334 R335 R446 R2207 C307 C341 C344 C342 R476 R471 R444 C478 D417 C414 Q411 C468 C466 IC411 R2202_2 C409 R411 R494 R2217 R414 C411 C412 C418 R451 R2206_2 R2203_2 R2201 R303 R305 C357 R417 R523 C481 R422 C480 R409 D406 C439 D4212 R449 R448
A B C D E F G H MPEG/MICON/DSP/RF_AMP SCHEMATIC DIAGRAM RF C4085 0.001 B 0.1 F 6.3V 47 SJV 0.1 F C4072 C4071 C4076 0.1 F 6.3V 47 SJV C4021 TIN D4008 MA111 R4045 GND (RF_GND) GND HOME TOUT_SW DVD_CD DRVSB RF OPU_A OPU_B OPU_C OPU_D OPU_E OPU_F VC SPDL_SENSSPDL_SENS+ MD_DVD MD_CD DVD_LD CD_LD SPINDLE_PWM SLED_PWM TRACK_PWM FOCUS_PWM DAC_VIDEO_C/D W807 C4044 1M R4012 C4034 27P CH X4001 100GT02727 27MHz C4028 0.1 F 52 C4035 27P CH C4079 0.
A B C D E F G H MEMORY SCHEMATIC DIAGRAM (DVD MT PCB) 8 8 FROM/TO MPEG/MICON/DSP/RF_AMP A18 0 W860 R4048 55 HA19 2.9 MEMCSO 2.4 HA0 MEMCS0 RD WR DQ0 A5 DE# A4 VSS A3 CE# A2 A0 A1 16 17 18 19 20 A6 21 31 30 DQ8 22 0 A7 23 2.9 RD DQ1 24 1.5 HD0 29 1.5 HD8 A17 28 1.5 HD1 DQ9 27 1.9 HD9 32 4.7K 0 SD_A11 0 NC 0 HA18 2.8 HA17 1.7 SD_A9 0 SD_A8 0 SD_A7 1.6 SD_A6 1.6 SD_A5 1.6 SD_A4 1.6 HA7 0 HA6 1.7 HA5 1.7 HA4 1.7 HA3 1.
A B C D E F G H MOTOR DRIVE SCHEMATIC DIAGRAM (DVD MT PCB) DSM2(06SD) C2350 C2328 0.1 B 6.3V 22 SJV C2348 8 CD_LD DVD_LD MD_CD (VR_DVD) MD_DVD (VR_CD) 33 R2360 VC DVD_CD 8 0.1 B FROM/TO MPEG/MICON/DSP/RF_AMP C2329 FROM/TO LOADER 6.3V 22 SJV 7 2.6 8 2.7 9 2.6 6.3V 47 SJV C2316 10 2.8 11 0 390 R2336 10K R2334 100 +-1% 13 3.7 14 1.7 16 2.7 4.7K R2327 5.6K TP2318 19 6.0 10K 1K (D_GND) GND TP2316 R2337 NC VIN 1 21 1.6 R2330 23 VIN2+ 20 1.
A B C D E F G H AUDIO/VIDEO SCHEMATIC DIAGRAM (DVD MT PCB) 8 8 FROM/TO REGULATOR CP8502 (CP403) A2001WV2-8P 0.001 B C8518 7 P.CON+A5V 6 GND 5 CD8502 P.CON+12V 4 CU282701 P.CON+3.3V 3 P.CON+3.3V 2 C8503 0.1 B C8519 C8539 EBMS160808A102_RDC45 GND 1 0.001 B 2.2uHNLV25 0.1 B 59 B8502 1 F 1uHNLV25 EBMS160808A102_RDC45 L8501 P.CON+A5V_D C8502 12P CH L8502 C8506 RESET SYS_MUTE 8 B8504 P.CON+5V_D DAC_C[U]C_VIDEO 150P CH C8504 DAC_VIDEO_A HCB1608KF-121T20 0.
A B C D E F G H FLASH SCHEMATIC DIAGRAM (DIGITAL PCB) 1 8 TRST_N TRST_N 2 TDO TDO 3 ASEBRKAK_N ASEBRKAK_N 4 BT002 GR6M D3.3V D3.3V 7 PC_TOOL_TX PC_TOOL_RX 6 PC_TOOL_RX PC_TOOL_TX 5 D_GND TMS TMS 5 TDI TDI 6 RESET_N RESET_N 7 FLASH_WP 8 IIC_OFF IIC_OFF FLASH_WP 3 SDA I2C_DATA ASEMD0 2 SCL I2C_CLK 1 GND 4 7 NC C2807 CD3805 P201-2739-1 NC/RESET ASEMD0 9 GND 10 VDD33 11 GND 12 8 D3.3V R2808 R2807 3.3 RESET_N 3.3 10K 0 10K ASEMD0 3.
A B C D E F G H DDR2 SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 R2823 DDR_SDRAM IC IC2802 HYB18TC256160BF-3S R2824 DACLK_N 1.9 DACS_N 1.8 DARAS_N 1.5 DACAS_N 2.0 160 R2820 160 AA17 SDA4 U18 L21 SDDM1 SDA5 V16 AA14 SDDM2 U21 AA11 NC 1.8 N18 1.8 K18 SDDM3 SDA6 SDA7 SDA8 SDA9 T20 SDDQS1 V13 SDDQS2 SDA10 Y18 NC V10 1.8 N19 1.8 K19 SDDQS3 SDA11 W16 SDA12 T18 1.
A B C D E F G H HDMI SCHEMATIC DIAGRAM (DIGITAL PCB) 8 HDMI1_SDA 6 TMDS_DATA1- HDMI1_CLK_N HDMI1_CLK_P HDMI1_D0N HDMI1_D0P 48 47 46 VCC ACLK- GND ACLK+ A0- GND A0+ A1- A1+ GND A2- A2+ 13 14 15 HDMI1_SDA 3.4 GND 25 26 27 28 29 30 31 32 3.1 NC3.1 NC 0 3.1 NC3.1 NC3.3 3.1 3.1 Y1- Y0GND GND GND 33 34 35 0 3.1 3.1 36 0 Y1+ B0+ 37 Y0+ 25 B1- Y2- B0- 42 43 44 45 HP_RST1 3.3 HP_RST 5.1 Y_HDMI_SDA 5.1 Y_HDMI_SCL 3.1 HDMI_CLKN 3.
A B C D E F G H JACK3 SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 FROM/TO AUDIO/VIDEO DVD_L B4303 [Y]VIDEO W827 GND TX FROM MICON START_SW FCM1608KF-102T02 B4305 B4306 EXT_MUTE-H TWIRE_RXDC FCM1608KF-102T02 R4302_1 TO AV SWITCH2 75 +-1% R4301_1 SPDIF_OUT 75 +-1% 10P CH START_SW TWIRE_TXDC FCM1608KF-102T02 R4303 100 100 CP4302 (CP8104) TWG-P23P-A1 LOUT_SOUND LOUT_SOUND R4305 VGA-B R4343 100 GND ROUT_SOUND VGA-R 1 VGA-G 2 VGA-B 3 NC 4 DGND 5 AGND 6 AGND 7 8 AGND
A B C D E F G H LVDS SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 SCALER IC IC2801 R8J66954BG 7 TO PANEL CP2804 A2006WR0-2X15P-HK C2801 100P CH LVDS0OUT0M E19 LVDS0OUT0P F19 3.3 0 0 GND B2808 HCB1608KF-221T20 B2809 1K 0 B2804 3.3 B2803 3.3 3.3 0.1 B C2876 10V 22 V-S C2879 0.
A B C D E F G H MICON SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 TO REGULATOR2 KEY_B KEY_A 1V_CTL TO JACK3 EXT_MUTE-H 7 7 S D 3.3 FROM/TO SCALER VIDEO/AUDIO S Q6202 2SK3019_TL 1 4.7K 15 16 SUR_SW 3.3V_POWER_H VREF 14 13 12 11 EEPROM_SDA 10 9 XIN VCC 1 MAIN_MICON_RXD EEPROM_SCL 2 3 4 0 3.4 3.1 1 0.5 3.4 R6226 ASEMD0 3.3 FROM/TO JACK3 NC DVD_RESET 3.3 R6223 3.4 4 100 100 0 R6228 4.7K 100 R6224 FROM/TO REGULATOR2 R6225 STBY-H 4.7K POWER_FAIL 3.
A B C D E F G H SCALER POWER SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 TO SCALER VIDEO/AUDIO 7 SCALER IC IC2801 AD_A3.3V FROM REGULATOR2 E8 E10 E12 K10 K11 K12 L10 L11 L12 M10 M11 M12 U7 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS33ADDA U3 6.3V 330 V-S 1 B 1 B 0.1 B C2910 VSS18 R4 C2914 1 B2820 0 10V 22 V-S 0.1 B C2923 0.1 B C2920 C2917 3.3 HCB1608KF-121T20 FROM HDMI VDD33 B2821 3.3 0 4 HCB1608KF-121T20 B2822 HCB1608KF-121T20 D1.8V VSS18 K5 HCB1608KF-121T20 3.
A B C D E F G H SURROUND SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 FROM SCALER VIDEO/AUDIO D3401 7 3.3 AT+5V 0 R3405 R3412 10K 10K MUTE_SW Q3404 KTC3875S_Y_RTK 5.0 R3413 D3.3V 3.3 FROM JACK3 0 TO JACK3 MUTE_SW Q3409 KRA101SRTK 0 ZERO_MUTE FROM FLASH R3406 A_MUTE 10K MUTE SW Q3405 KTC3875S_Y_RTK 0 R3414 AUDIO_MUTE C3408 10K 5.0 0 0 LOUT_SOUND 0 1K MUTE SW Q3411 KTC3875S_Y_RTK 5.0 5.0 0 ROUT_SOUND R3422 560 R3427 0 6 4.5 0 1K C3413 FROM MICON 1 B 6 5.
A B C D E F G H TUNER SCHEMATIC DIAGRAM 25 21 IF_OUT2 8 W878 TO SCALER VIDEO/AUDIO 8 CH 7 33P L5801 C5814 22uHNLV25 0.4 0.2 TU_CVBS 0.1 B B B5809 5.0 FCM1608K C5857 F-102T02 0 NC 0.1 B 0.9 2.6 3.3 3.3 31.5 1.0 NC B 0.1 B5808 5.0 FCM1608K C5856 F-102T02 1.5 C5805 0.1 C5806 C5803 7 6.3V 220 V-S 2.0 NC 0 NC 2.6 NC 0.
A B C D E F G H SCALER VIDEO/AUDIO SCHEMATIC DIAGRAM (DIGITAL PCB) 8 SCALER IC IC2801 8 R8J66954BG FROM/TO JACK3 PC_V PC_H PC_V 3.2 PC_H 3.2 C2946 3.2 AV3/AV4_Y C2937 SW_Y_IN AV1_CVBS 0.1 TU_CVBS 7 VGA-G 9 B AV3/AV4_PB 0.1 0.1 0.1 B C2931 0.1 VGA-R B C2932 SW_C_IN C2928 AV2_CVBS C2927 0.1 VGA-G 0.1 0.1 C2941 10 2.0 0.1 B C2934 0.1 B C2935 0.1 HP_RST 0.1 B C2943 0.1 5 W890 VGA-R C2926 0.1 B P2 VREFB P3 VIN3B FROM/TO JACK3 1.6 B 1.3 2.7 0.1 1.
A B C D E F G H AV SWITCH2 SCHEMATIC DIAGRAM (DIGITAL PCB) 8 Lch SW IC IC6552 NJM2534V C6570 4.3 1 8 0 10 BUFFER 7 4.0 FROM/TO SCALER VIDEO/AUDIO SW_L B 3.3 2 22uHNLCV32T 16V 10 V-S L6551 P.CON+9V 1 B C6564 C6563 8 LRCK ASW0 0 4.7K R6567 R6573 10 B 100 0 9.3 X6551 100DT01217 12.288MHz 2.3 2.1 4.8 10K TU_AUDIO_R TU_AUDIO_R 10 B 4 3.2 C6566 R6572 10 B 100 FROM JACK3 AV1_Y DVD_R AV1_C SW_L SW_R SW_Y_IN 6 0/3.3 4.
A B C D E F G REGULATOR2 SCHEMATIC DIAGRAM H TO FLASH D3.3V 8 8 BLON (DIGITAL PCB) GND FROM/TO REGULATOR TO DDR2 CP3001 (CP401) TWG-P23P-A1 TUNER+30V POWER_FAIL POWER_FAIL 3 SYS_POWER_H 21 KEY_A GND KEY_A 8 7 6 PGND 2.5 5 1 GND 5.3 0 (typ 1.8A) L3002 B3003 TUNER+30V D3.3V D5.0V 6 TO SURROUND P.CON+9V AT+5V D3.3V BLON 22 LIGHT_POWER_H TO TUNER D1.0V HCB1608KF-181T20 10uHTSL0808 10 C VDIM NC SW 10 C LIGHT_CTL AT+3.
A B C D E F G H POWER SCHEMATIC DIAGRAM R523 C444 47K R460 +-1% R454 R455 R456 2.2K +-1% 2.2K +-1% 330 P_GND 6 10K R476 4.
A B C D E F G H POWER2 SCHEMATIC DIAGRAM (POWER PCB) 8 8 1 B C456 +24V +24V 2 0.01 FROM/TO POWER R473 7 1K 2W R481 1K 2W CP406 A2001WR-14A +24V 3 +24V 4 +24V 5 INV_SW+24V INV_GND GND 6 GND 7 AT+5V GND 8 P_GND GND 9 GND 10 SW+12V[UNREG] INV_GND NC SYS_POWER_H YXF NC LIGHT_CTL W814 6 VDIM 16V 470 MHE 5.1 R485 2.5V ON/OFF 4 0 5 2.5 0 47uH 1315 5 820 +-1% C461 8.2K +-1% LCD+B SW Q411 KRC102SRTK PANEL_POWER_H LCD-H R484 6.
A B C D E F G H REGULATOR SCHEMATIC DIAGRAM (POWER PCB) 8 8 P.CON+5V SW+12V 1 BOOT SS 8 V_IN EN 7 AT+5V 2 W806 IC413 LV5795-TE-L-E 6 3 51 R407 2.7K +-1% 0.1 B C489 B C487 R422 +-1% 3.9K +-1% 22uH1315 GND(M) 8 P.CON+6V 7 P.CON+A5V 6 GND 5 P.CON+12V 4 P.CON+3.3V 3 P.CON+3.3V 2 GND 1 0.1 B C488 L403 0.1 B 4.7K R465 C490 R418 B 22 22 B C479 C476 22 B C477 B 0.
A B C D E F G H AV SWITCH SCHEMATIC DIAGRAM 8 8 (POWER PCB) 7 7 1 B AV_SW IC IC6502 NJM2750M(TE1) 1 2 3.2 3 4.8 NC 4 3.2 5 4.8 6 IN1a 4.8 7 GND 4.8 NC 4.8 4.8 15 R6510 1K OUTa CNT1 14 Vcc IN2a 13 9.6 AV3/AV4_PR IN3a CNTT2 12 SW_L 4.8 8 16 0 Vref IN4a 11 W885 AV3_PR C6512 C6509_1 6 16V 47 YK P.CON+9V OUTb IN1b 4.8 AV3/AV4_PB 16V 47 YK AV3_Y 5 AV3/AV4_Y SW_R R6511 4.8 1K 0 NC 10 W883 4.8 NC IN2b 9 W884 AV3_PB C6513_1 IN3b IN4b 4.
A B C D E F G H SOUND SCHEMATIC DIAGRAM (POWER PCB) 8 8 SOUND AMP IC IC302 AN17808B + - + + FROM JACK2 C307 CH2 NC MUTE OUT 6 7 8 0 NC 0.7 3.7 7 STAND CH1 GND VCC -BY OUT 9 10 11 12 0 16.5 0.7 3.3 C357 ATT. RIPPLE FILTER CH1 CH2 GND NC RF IN IN 1 2 3 4 5 0.2 16.0 0 0.2 NC C349_1 0.1 B + 7 ATT.CONT. 17 ROUT_SOUND B 25V 1000 MHE W829 (A_GND) GND 2 3 GND 3 2 4 1 (R) R337 4.7K 4.7K R336 SP301 S0412F06 3.9K ZL W828 C346_2 3.
A B C D E F G H JACK SCHEMATIC DIAGRAM (POWER PCB) 8 8 FROM/TO REGULATOR HDMI AUDIO IN J4201 MSJ-2000B_AG(O87) R4208 1K 1 7 DVI_A_IN_R CVBS_IN_2 J4205 RCA-349-00C-02 B R2 AR2 1K 1 AL2 AR1 NC 1 R4271 DVI_A_IN_R E C4220 AR2 L2 H2 1/4W DVI_A_IN_L 4 100 V2 H3 R4239 AV2_CVBS 5 1 B H1 C4207 TO AV SWITCH 47K R4212 C4205 1K 20 2 C4209 22P CH R4207 3 2 R4214 L DVI_A_IN_L 1 B 22P CH R GND (A_GND) 19 3 47K 7 C4208 AV3_Y AV3_PB 1K AV3_PR 6 75 R4277
A B C D E F G H JACK2 SCHEMATIC DIAGRAM (POWER PCB) 8 8 FROM/TO JACK3 (CP4203) CP4203 127301123K2 23 22 7 21 GND GND 19 FILTER_MUTE FILTER_MUTE 18 POP_MUTE POP_MUTE 17 YUV_SW_Y AV3/AV4_Y 15 14 13 12 11 10 9 7 ROUT_SOUND ROUT_SOUND 20 16 6 LOUT_SOUND LOUT_SOUND FROM JACK S1_DET GND AV3/AV4_PB YUV_SW_U AV2_CVBS GND AV1_CVBS AV3/AV4_PR YUV_SW_V AV1_Y GND ASW2 ASWW2 SW_L AUDIO_SW_L 8 GND 7 VIDEO02 6 GND AV1_C SW_R AUDIO_SW_R AV2_CVBS ROUT_SOUND LOUT_SOUND
A B C D E F G H OPERATION/REMOCON SCHEMATIC DIAGRAM 8 8 (REMOCON PCB) FROM/TO JACK2 OS2201 ROM-V338TAO 7 Vout CP2201 (CP4201) A2001WR2-5P REMOCON IN 1 GND 2 AT+5V 3 STANDBY LED 4 1 GND 2 R2208 B+ 3 47 1/4W 7 OS 26 CD2201 E8253101 G STANDBY/POWER D2201 LTL-1BEFJ-002A R 6.
A B C D E F G H INTERCONNECTION DIAGRAM 8 H1 5 H2 3 2 COMPONENT_VIDEO_IN_1 J4203 H1 AV1_Y 2 S1_DET AV1_C 3 3 3 3 AV1_C ASW1 4 4 4 4 ASW1 VIDEO01 5 5 5 5 VIDEO1 GND 6 6 6 6 GND 7 7 7 7 VIDEO2 7 VIDEO02 GND E 1 5 4 H2 2 8 GND 9 9 9 AUDIO_SW_L 10 10 10 AUDIO_SW_R 11 11 11 11 AUDIO_SW_R GND 12 12 12 12 GND YUV_SW_V 13 13 13 13 YUV_SW_V GND 14 14 14 14 GND YUV_SW_U 15 15 15 15 YUV_SW_U GND 16 16 16 16 GND 5 H3 YUV_
WAVEFORMS FLASH MICON 20ns 200mV 20ns 200mV 1 10us 100mV 7 13 TUNER 20ns 200mV 10us 0.5V 2 10us 100mV 8 14 HDMI SCALER VIDEO/AUDIO AV SWITCH 2 20ns 200mV 20us 500mV 2ms 100mV 3 9 15 JACK 3 0.2us 200mV 20us 500mV 4 2ms 100mV 10 16 SOUND 2ms 500mV 10us 0.5V 5 2ms 500mV 1ms 200mV 11 17 10us 200mV 6 1ms 200mV 12 18 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS JACK AUDIO/VIDEO 2ms 100mV 200µs 1.0V 19 2ms 100mV 56 200µs 1.0V 20 57 MPEG/MICON/DSP/RF_AMP 10ns 500mV 10µs 200mV 52 100µs 500mV 58 10µs 100mV 53 59 200ns 1.0V 54 MEMORY 100µs 500mV 55 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
MECHANICAL EXPLODED VIEW 124 126 127 211 209 211 209 109 211 125 209 211 209 211 102B 104C 202 104C 202 211 211 104C 202 104A 211 102F 211 211 102E 102C 211 102A 211 210 206 206 206 206 205 102G 205 121 102 103C 206 206 206 206 206 104C 103A 103A 117 102D 211 211 202 104C 103 102F 104B 104C 104 103B 120 121 131 131 207 203 113 212 209 203 203 203 203 110 209 114 208 114 203 112 108 122 114 PCB280 (OPERATION 2 PCB ASS'Y) 203 PCB240 (POWER PCB ASS'Y)
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) CD3805 HOLDER CORD POLYBAG INSTRUCTION(RED CAUTION) INSTRUCTION BOOK(E/F/S) REGISTRATION CARD(SHARP) TM101 PACKAGE TOP PACKAGE STAND-TOP PACKAGE STAND-BOTTOM SCREW LAMIFILM BAG GIFT BOX SHEET BARCODE PACKAGE BOTTOM J1-3
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) PACKAGE STAND-TOP FILM BAG (791WHA0159) SCREW FILM BAG (791WHA0160) PACKAGE STAND-BOTTOM J1-4
DVD DECK EXPLODED VIEW 600 601 608 CD2001 M2602 603 606 703 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y. 605 703 702 702 607 AA 605 703 701 602 SW2 604 704 PCB640 (SW PCB ASS'Y) 705 CLASS PART NO. PART NAME GREASE Y315061000 G-555G CD2301 NOTE: Applying positions AA for the grease are displayed for this section. Check if the correct grease is applied for each position.
MECHANICAL REPLACEMENT PARTS LIST REF. NO. PART NO.
DVD DECK REPLACEMENT PARTS LIST REF. NO. PART NO. ! 600 A50N01P650 DVD MECHA ASS'Y DESCRIPTION A50N01P650 601 602 603 604 605 606 607 608 92SBB0033A 92AAA0017A 92P100088A 92P100117A 92P200017A 92P200018A 92P100116A 800WFAA008 LOADER SUB ASS'Y FEED RACK ASS'Y GEAR,MOTOR GEAR,MIDDLE INSULATOR, F INSULATOR, R GEAR,FEED CUSHION C DLM1D29-31 701 702 703 704 705 92P700007A 814011723U 816112080U 813381750U 811022080U SCREW,GEAR FEED SCREW,PAN SEMS.
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO.
ELECTRICAL REPLACEMENT PARTS LIST *** TRANSISTORS *** Q3003 Q3004 Q3401 Q3402 Q3403 Q3404 Q3405 Q3406 Q3408 Q3409 Q3410 Q3411 Q3412 Q3606 Q3607 Q3608 Q3609 Q4301 Q4303 Q4304 Q4306 Q4307 Q4308 Q4310 Q4311 Q4312 Q5801 Q5802 Q6201 Q6202 TNAAC05002 TNAAC05002 TCAA3875SY TPAAA05001 TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY TPAAA05001 TCAA3875SY TCAA3875SY TCAA3875SY T27T030190 T27T030190 T27T030190 TCAA3875SY TCAA3875SY TPAAA05001 TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY TC
ELECTRICAL REPLACEMENT PARTS LIST B4313 B4314 B4315 B5802 B5804 B5808 B5809 B6551 B6552 B6553 B6556 024HC51023 024HC51023 024HC51023 024HC51023 024HC51513 024HC51023 024HC51023 024HC51216 024HC51023 024HC51023 024HC51816 CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS FCM1608KF-102T02 FCM1608KF-102T02 FCM1608KF-102T02 FCM1608KF-102T02 FCM1608KF-151T06 FCM1608KF-102T02 FCM1608KF-102T02 HCB1608KF-121T20 FCM1608KF-102T02 FCM1608KF-102T
ELECTRICAL REPLACEMENT PARTS LIST CP2803 CP4301 CP4303 CP6201 06GG2C0029 06GG2E0019 06G8S21504 06GG2B0029 CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE A2001WV-12A A2001WR-14A 1B630020 A2001WV-11A SH3001 SH3002 SH3003 SH3004 SH3005 126D000045 126D000045 126D000045 126D000045 126D000045 TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN YQ-12 YQ-12 YQ-12 YQ-12 YQ-12 DVD MT PCB ASS'Y *** PCB *** PCB130 A50Q01P130 DVD MT PCB ASS'Y DMG097A *** DIODES *** D
ELECTRICAL REPLACEMENT PARTS LIST CP2302 CP2303 CP8502 069EV5T060 069EV6T060 069S280629 CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE 04_6232_105_015_800+ 04_6232_106_015_800+ A2001WV2-8P *** CRYSTAL & CERAMIC OSCILLATORS *** X4001 100GT02727 CRYSTAL SMD-49 C27000J029 *** OTHERS *** CP8501 06GG2E0019 CONNECTOR PCB SIDE A2001WR-14A SH8501 SH8502 SH8503 SH8504 126D000045 126D000045 126D000045 126D000045 TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN YQ-12 YQ-12 YQ-12 YQ-12 POWE
ELECTRICAL REPLACEMENT PARTS LIST *** DIODES *** D401 ! D404 ! D405 D406 ! D407 ! ! ! ! ! ! ! D408 D410 D411 D412 D413 D415 D416 D417 D418 D421 D424 D425 D426 D427 D432 D433 D435 D437 D440 D442 D443 D444 D445 D4207 D4209 D4210 D4211 D4212 D4213 D4214 D97U03301B D6CE24110A D4CKN54060 D28R1QS040 D4CKN54060 D1VT001330 D1VT001330 D1VT001330 D97U03R91B D97U03001B D2WXN40050 D28F31DQ06 D28R1QS040 D2WXN40050 D28R1QS040 D97U03R31B D97U02701B D1VT001330 D97U02701B D4AT106FE0 D4AT01H3E0 D2CFC91020 D28AH10A20 D2
ELECTRICAL REPLACEMENT PARTS LIST Q409 Q410 Q411 Q412 Q416 Q417 Q418 Q420 Q421 Q422 Q423 Q424 Q425 Q4211 Q4212 TAAA1504SY TNAAB05003 TNAAB05003 TJ5AK302T0 TAAA1504SY TAAT01281Y T67J017590 TCAA3875SY TNAAA05001 TBA0011510 TCAA3875SY TCAA3875SY TJ5AK302T0 TNAAB05003 TPAAC05002 TRANSISTOR SILICON COMPOUND TRANSISTOR COMPOUND TRANSISTOR FET TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON FET COMPOUND TRANS
ELECTRICAL REPLACEMENT PARTS LIST SH404 SH406 SH407 SH410 126D000045 126D000045 126D000045 126D000045 TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN YQ-12 YQ-12 YQ-12 YQ-12 OPERATION PCB ASS'Y *** PCB *** PCB270 A50Q01P270 OPERATION PCB ASS'Y CEG358A *** SWITCHES *** SW2201 SW2202 SW2203 SW2204 SW2205 SW2206 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505
ELECTRICAL REPLACEMENT PARTS LIST ! SP302 070Y056007 SPEAKER S0412F06 TM101 076B0MR030 TRANSMITTER ETR0088-010171 ! V2301 09EV126010 LCD V260B1-L01_M RESISTOR RC................... CARBON RESISTOR CAPACITORS CC................... CERAMIC CAPACITOR CE................... ALUMI ELECTROLYTIC CAPACITOR CP................... POLYESTER CAPACITOR CPP.................. POLYPROPYLENE CAPACITOR CPL.................. PLASTIC CAPACITOR CMP.................... METAL POLYESTER CAPACITOR CMPL................
COPYRIGHT © 2008 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
