Manual

QUICK REFERENCE
If the remote control falls to operate TV functions,
replace the batteries in the remote control unit,
1 Open the battery cover.
2 Inser_ two "AAA" size batteries (supplied with the
product),
• Place the batteries with their terminals
corresponding to the ( _ ) and (-) indications in
the battery compartment.
3 Close the battery cover.
• = = - o = e o
Use the remote control unit by pointing it towards the
remote control sensor on the 'f_/. Objects between
the remote control unit and the remote control
sensor may prevent proper operation.
Remote c!
_'"" "_i: ")]2111t_glaetis(6_ed[.le n the
[] Cautions regarding the remote control unit
• Do not expose the remote control unit to shock, in
addition, do not expose the remote control unit to
liquids, and do not place it in an area with high humidity.
• Do not install or place the remote control unk under
direct sunlight. The heat may cause deformation of the
remote control unk.
• The remote control un_ may not work properly if
the remote control sensor on the TV is under direct
sunlight or strong lighting, in such cases, change the
angle of the lighting or the TV, or operate the remote
control unit closer to the remote control sensor.
Improper use of batteries can result in chemical leakage
or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types
of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new
batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they are worn out.
Chemicals that leak from batteries that come in contact
wkh skin can cause a rash. If you find any chemical
leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a
shorter life expectancy due to storage condkions.
• if you will not be using the remote control unit for an
extended period of time, remove batteries from it.
J
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG
THE TELE_/ISION FROM THE OUTLET AND REPE:AT
THE INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE
CONTTkCT US AT 1-800-BE-SHARP.
Preparation
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of ttle types of
connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable wittl an
F-type connector, plug it into tile antenna terminal at tile rear of tile TV set. For connecting tile antenna cable to
tile TV, use commercially available cables.
fConneeting Antenna Cable
= Connect the antenna cable to the "rv using one of the methods in the illustration as shown (_, _,
or _).
Home Antenna
Cabme without a Cable TV lead-In
terminal
(75-ohm)
CATV converter _ _:: t?..... :_
Coaxial cable
VHF/UHF antenna
"_7 Home Antenna5-ohm coaxial cable (round) terminal (75-ohm)
Coaxial cable
Combination VHF/
UHF antenna
_ Separate VHF/UHF
antenna
"Y_75-ohm coaxial cable (round)
I
q
_O0-ohm twin-lead or 3QO/75_ohm_ =_
cable (fiat) I aoap_er j
UHF
To TV antenna
terminal
\
1.A 75-ohm system isgenerally a round cable with F-type connector
that can easily be attached to a terminal without tools.
2.A 300-ohm system is a fiat "twinqead" cable that can be attached
to a 75-ohm terminal through a 300/75-0hm adapter.
_ F-type connector should be finger-tightened on_y,
When connecting the RF cable to the TV set, do not tighten
F-type connector wkh tools.
If tools are used, it may cause damage to your %/set. (The
breaking of internal circuit, etc.)
......F-type connector
__ 75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
75-ohm coaxial cable
_-10