NUJC370 NUJC360B

ManualsBrandsSharp ManualsSolarLC32LE210EV

SIM02E-005

PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PV MODULES.

PLEASE PASS ALONG THE ATTACHED USER MANUAL TO YOUR CUSTOMER.

INSTALLATION MANUAL

– Crystalline Photovoltaic Module –

# IMPORTANT SAFETY INSTRUCTIONS p.1

# GENERAL INSTRUCTIONS p.1 ~ p.3

# INSTALLATION INSTRUCTIONS -PHOTOVOLTAIC MODULES- p.4

# ELECTRICAL OUTPUT AND THERMAL CHARACTERISTICS p.4

# Annex (normative) p.5

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety instructions for the PV module

that must be followed during the maintenance of PV modules.

To reduce the risk of electric shock, do not perform any servicing

unless you are qualified to do so.

1. The installation must be performed by a certified installer

/servicer to ensure system integrity and safety.

2. The installation is only allowed after referring and

understanding of this INSTALLATION MANUAL. If you don’t

have your personal copy, please contact your installer or local

SHARP office listed in SHARP Solar web site : URL : http://

global.sharp/solar/en/

3. Do not pull the PV cables.

4. Do not touch any surface of PV module.

5. Do not place/drop objects onto the PV modules.

6. Do not disassemble or attempt to repair the PV module by

yourself.

7. Do not drop the PV module.

8. Do not damage, pull, bend, or place heavy material on cables.

9. Upon completion of any service or repairs, ask the

installer/servicer to perform routine checks to determine that

the PV modules are in safe and proper operating condition.

10. When replacement parts are required, be sure the

installer/servicer uses parts specified by the manufacturer with

same characteristics as the original parts. Unauthorized

substitutions may result in fire, electric shock, or other hazard.

11. Consult your local building and safety department for required

permits and applicable regulations.

12. As a result of sliding snow, the mechanical load increases when

the number of PV module rows in the matrix of a PV installation

increases. When mounting the PV module in the portrait

orientation for more than 3 rows, the accumulated snow load

may cause the lower edge of the PV module frame to deform.

Take necessary measures (e.g. snow stopper) to avoid

possible damage.

13. Periodically remove any overhanging snow and/or ice from the

PV module framework as it may cause deformation of the PV

module frame.

GENERAL INSTRUCTIONS

1. INTRODUCTION

This INSTALLATION MANUAL contains essential information for the electrical and mechanical installation that you must know

before installing SHARP PV modules. This also contains safety information you need to be familiar with. All the information

described in this manual are the intellectual property of SHARP and based on the technologies and experiences that have been

acquired and accumulated in the long history of SHARP. This document does not constitute a guaranty, expressed or implied.

SHARP does not assume responsibility and expressly disclaims liability for loss, damage, or expense arising out of or in any way

connected with installation, operation, use or maintenance of the PV modules. No responsibility is assumed by SHARP for any

infringement of patents or other rights of third parties that may result from use of PV module. SHARP reserves the right to make

changes to the product, specifications or INSTALLATION MANUAL without prior notice.

2. COMPONENTS

3. GENERAL INFORMATION

(INCLUDING WARNING AND SAFETY)

The installation of PV modules requires a great degree of skill

and should only be performed by a qualified licensed

professional, including licensed contractors and licensed

electricians. Please be aware that there is a serious risk of

various types of injury occurring during the installation including

the risk of electric shock. All SHARP PV modules are equipped

with permanently attached junction boxes that will accept

variety of wiring applications or with a special cable assembly

for ease of installation, and they do not require special

assembly.

GENERAL WARNING

1. PV modules are heavy. Handle with care.

2. Before you attempt to install, wire, operate and maintain

the PV module, please make sure that you completely

understand the information described in this

INSTALLATION MANUAL.

3. Contact with electrically active parts of a PV module such

as terminals can result in burns, sparks and lethal shock

whether the PV modules are connected or not.

4. PV modules produce electricity when the sufficient sunlight

or other sources illuminate the PV module surface. When

the PV modules are connected in series, voltage is

cumulative. When the PV modules are connected in

parallel, current is cumulative. As a result, a large-scale PV

MODEL

NU-JC370、NU-JC365、NU-JC360B、NU-JC355B

CAUTION: HIGH VOLTAGE

To reduce the risk of electric shock, do not touch.

Solar Photovoltaic Cell

Junction Box

Superstrate Glass

Frame

Connector

Electriclal Cable

Summary of content (6 pages)

PAGE 1
SIM02E-005 PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PV MODULES. PLEASE PASS ALONG THE ATTACHED USER MANUAL TO YOUR CUSTOMER. INSTALLATION MANUAL – Crystalline Photovoltaic Module – MODEL NU-JC370、NU-JC365、NU-JC360B、NU-JC355B # IMPORTANT SAFETY INSTRUCTIONS p.1 # GENERAL INSTRUCTIONS p.1 ~ p.3 # INSTALLATION INSTRUCTIONS -PHOTOVOLTAIC MODULES- p.4 # ELECTRICAL OUTPUT AND THERMAL CHARACTERISTICS p.4 # Annex (normative) p.
PAGE 2
SIM02E-005 5. 6. system can produce high voltage and current which could present an increased hazard and may cause serious injury or death. Do not connect the PV modules directly to the loads such as motor since the variation of the output power depending on the solar irradiation causes damage for the connected motor. 1: In the case of a brushless motor, the lock function becomes active and the hall IC is most likely to be damaged.
PAGE 3
SIM02E-005 4. SITE SELECTION In most applications, the PV modules should be installed in a location where there is no shading throughout the year. In the Northern Hemisphere, the PV modules should typically face south, and in the Southern Hemisphere, the PV modules should typically face north. Please make sure that there are no obstructions in the surroundings of the site of installation.
PAGE 4
SIM02E-005 mark. If dirt build-up becomes excessive, clean the glass surface with water only. INSTALLATION INSTRUCTIONS -PHOTOVOLTAIC MODULES1. INSTALLATION Mounting Using Clips: The PV modules can be mounted with clips (clamps) as defined in the following. Note that the mounting clips should meet the required dimensions as defined in the Figure1. Note that the CLIP CENTER POSITION (e) from the module corner should be located in the range as specified in the Annex.
PAGE 5
SIM02E-005 Annex (normative) 【D e sig n lo a d 】 T a b le .A 1 D e s ig n lo a d b y c lip p in g o n lo n g fra m e s (s e e F ig . A 1 ) design load according to IE C 61215 clip center position T a b le .A 3 D e s ig n lo a d b y u s in g B o lt H o le s (s e e F ig .
PAGE 6
SIM02E-005 e e e e Fig. A1: Clipping position on long frames Fig. A2: Clipping position on short frames S S L S S L L 1. Spring washer Material: Stainless steel Diameter: M8 8.2/15.4mm Thickness: 2 mm (reference value) 3. Bolt Material: Stainless steel Size: M8 Diameter: M8 x 20mm L 2. Washer Material: Stainless steel Diameter: M8 8.5/15.5mm Thickness: 1.6 mm (reference value) 4. Nut Material: Stainless steel Size: M8 Fig. A3-1: The components for BOLT & NUT Fig.