Supplemental information for PN-CD701 Ver.1.
Index It is supplemental document of both setup and operation manual. There are reference information which are not described in manual, please utilize it as well as setup / operation manual. 1. 2. 3. 4. System requirement Condition of connecting Mac / Chrome OS Outline of USB type-C Conditions of network connections to the PN-CD701 4-1. Common functions of both LAN ports 4-2. Use case 4-3. Technical background 4-3-1. Network isolation 4-3-2. Network requirement for WSI (IoT sensor data) 4-3-3.
1. System requirement System requirement *MacOS is supported with mouse operation and single touch. Chrome book is supported multi touch(touch digitizer), but Touch pen does not work. ＜Referenced information＞ PN-CD701 , because of featuring 4K resolution, should be recommended the controller which has sufficient ability for 4K resolution. “Sufficient” means -60Hz refresh rate on 4K resolution. -Smooth operation on 4K resolution in the application produced by Microsoft(i.e. Windows Ink).
2. Condition of connecting Mac / Chrome OS PN-CD701 is designed for using with Windows devices. It supports both Mac OS and Chromebook but there are some limitations.
3. Outline of USB type-C USB type-C is a new standard which has various capabilities for connecting IT devices. Some of these capabilities are unique to USB type-C. Please see descriptions below how to utilize new functions. Major functions of USB type-C - Connect devices and data transfer (Same as USB 2.0 but higher speed) - “DP alt mode” which means that it works as a DisplayPort to transmit video.
3. Outline of USB type-C Caution for running USB type-C cable ◆ When a USB type-C cable is connected, the functions shown it the table below are available. Function of USB type-C Available/ Not Available DP Alt mode(Video stream) Available Network * Available Touch (Data Transport) Available Power Delivery Available(MAX 60W) [Note] “In case you using USB-C cable from your market (not delivered with PN-CD701), the take care the this cable should be supported power charging of 60W or more.” Table.
3. Outline of USB type-C Caution for running USB type-C cable ◆ USB type-C Out can be used for video output. • • • • Only video signals are output from USB type-C Out. The signal of Wireless Cast can not be output. Do not convert the cable from the USB type-C cable. Only the same display or allowed display is supported for the display connected to the Out side. Figure. Rear Left View ◆ About “Multi board” You can display video on a second device using USB-C Out.
4. Conditions of network connections to the PN-CD701 4-1. Common functions of both LAN ports PN-CD701 has 2 wired LAN ports. One is “LAN 1”, and the other is “LAN 2”. Each port serves a different function, see below for details of each port. LAN 1 : LAN port for connecting external PC/s LAN 1 connection is routed to USB type-C and USB-B ports. The connected PC device will receive internet access via the USB type-C or USB-B port. Fig.
4. Conditions of network connections to the PN-CD701 4-2. Use case User who has a compatible USB type-C connection on their PC will also get a LAN connection via the USB type-C cable from PN-CD701. Fig.2: LAN connection diagram IoT sensor Advantage: Smart connectivity User can quickly connect video, touch, LAN and power delivery by using only one USB type-C cable.
4-3. Technical background 4-3-1. Network isolation • Each LAN port (LAN 1, LAN 2) are separate and will have different IP addresses. • There are no network management devices (routers or switches) inside. • Works with different LAN settings. “LAN 1” is completely isolated from the internal controller of PN-CD701 So there is no security breach concerns from connected PC devices.
4-3. Technical background 4-3-2. Network requirements for WSI (IoT sensor data) Tips: Required network connection for IoT sensors is always LAN 2 Internet connections Internet connections are available using intranet. If network devices filter IoT packets, they can accessed though router, proxy, GW/FW. Condition of IP address It can use DHCP. And supports both IPv4 and IPv6.
5. Notes on updating firmware 5-1. OOBE Out-Of-Box-Experience(OOBE) is displayed at the first startup or after resetting. Since there is a setting to search for the latest FW in the OOBE setting, Please prepare the Internet environment at LAN2 and execute the update. Figure.
5. Notes on updating firmware 5-2. USB Flash Drive*1 You can update using a USB flash drive. Please perform the following procedure. 1.Please start your computer and Download the “PN-CD701” Zip file from the SHARP Information Display Downloader*2. 2.Unzip the downloaded file and save the “FWU_Config” file and “WCD70” directory to the USB memory directly under the root. Figure. SHARP Information Display Downloader 3. “Insert the USB flash drive into the USB terminal of “FOR CAM” next to the Service port.
5.
5. Notes on updating firmware 1. If the firmware update is completed successfully, the screen on the right will be displayed. 2. When the firmware update is completed successfully, the screen on the right will appear. If you do not have an Internet connection, an error message will appear, but please continue to the next step. (1) Initial startup screen after the update is successfully completed 3.
5. Notes on updating firmware 5-3. OTA Firmware Updates Note This method requires a network environment. Connect an Internet-capable LAN cable to LAN2 terminal. PN-CD701 will perform the firmware update directly via the Internet. If you want to update the FW while keeping the display settings, you can use OTA update. 1.Please open the setting menu of PN-CD701 and press the Admin menu. 2. Click Update in OTA Firmware Updates. Figure.
6. Enable LAN 1 Network 6-1. Procedure to enable LAN1 Network Access “System” menu Switch “LAN1 Network” to “on” Enter user or admin passcode LAN1 Network becomes available 6-2. LAN 1 network always on If you want to enable LAN1 function permanently, it can be set via “Admin” menu.
6. Enable LAN 1 Network 6-3. Matrix of LAN1 Network status LAN 1 Network will be back to “disable” after disconnect PC devices because of security issue. (Except when you choose “LAN 1 Network Always-on”.
7. How to install / use Android apps on PN-CD701 Note In order to enable this function, the customer must contact the dealer. 7-1. Preparation: Allow installation of 3’rd party applications. (Sideloading*) • You can install the app from “Admin” menu. • Please insert the USB flash drive that .apk files are stored in the root into the USB socket labeled “FOR CAM”. [Note] Please take care that only limited number of APPs are working. [Flow Chart] Access to “Admin” and tap “Install New Apps” Choose .
7. How to install / use Android apps on PN-CD701 Note In order to enable this function, the customer must contact the dealer. 7-2. How to display newly installed apps. Please follow the steps below. 1.
8. Notes on camera attached to PN-CD701 The camera attached to PN-CD701 supports 4K resolution, but camera video output is Full HD because the cable included with PN-CD701 is a USB2.0 cable. (Because main application “Teams” and “Skype for Business” camera images are supported up to Full HD.) If you want to show 4K image with different applications, please prepare the following connection environment. Preparation Replace the USB2.0 cable that connects camera and PN-CD701 with a USB3.
9. Tips 1. What are red dot or bell mark on each icons in PN-CD701? It indicates something update or attention in each items. It is same as “Notification dot” which is implemented from Android 8 (Oreo). Please tap each icons which are displayed red dot / bell to confirm updated information. 2. Wireless display projection conditions Attention/Update (UI for OSD and date/time) Locked Attention/Update (UI for Settings Panel) (Admin setting is locked behind a password.
10.
10.
10.
