LCD MONITOR LCD FARBMONITOR MONITEUR LCD MONITOR LCD MONITOR LCD LL-T1512W OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUALE D’USO MANUAL DE FUNCIONAMIENTO
Notice for Users in the USA ............................................................................................................................ 4 TCO'99 ............................................................................................................................................................ 5 Notice for Users in Europe .............................................................................................................................. 7 Notice for Users in the UK ........
Notice for Users in the USA FCC Statement WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
English Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire.
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG. Dette udstyr overholder kravene i direktiv nr.
Notice for Users in the UK FOR CUSTOMERS IN U.K. IMPORTANT The wires in this mains lead are coloured in accordance with the following code : GREEN-AND-YELLOW : Earth BLUE : Neutral BROWN : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows.
- - - Monitor and accessory checklist - Please check that the following items are included in the package. - LCD monitor (1) - AC adapter (1) (model name:NL-A56J) - USB cable (1) (model name:QCNW-1042MPZZ) - Utility Disk (For Windows/Macintosh) (1) - Operation manual (1) The LCD module built in this LCD Monitor is manufactured with highly precise technology. However bright pixels or blank pixels may appear constantly. Also an irregular color and brightness may appear depending on view angle.
Product description Front view Operation Panel 1) MENU button 2) SELECT button button 3) 4) POWER button (LED) 5) INPUT button 6) COLOR MODE button 7) BRIGHT button 8) BRIGHT SENSOR This button is used to open, select and close the On Screen Display (OSD) Menu. When the OSD Menu is displayed, selects the menu option to be adjusted. When the OSD Menu is displayed: These buttons are used to increase or decrease the value of a selected option.
Rear view 9) Security lock anchor By connecting a security lock (purchased separately)to the security lock anchor ,the monitor is fixed so that it cannot be transported. The security slot works in conjunction with kensington Micro Saver Security Systems. 10) Ventilation opening The openings to give off an internally generated heat. Note: Never block the ventilation openings as this may lead to overheating inside the monitor and result in malfunction.
Connecting the monitor and turning the monitor on and off 4. Mounting the AC adapter 1) Bend lightly the root part of the cord. (Do not over bend the cord.) 2) Insert the root part of outlet cord until it goes out partly, from the round hole.and then slowly put down the AC adapter. Connecting the monitor to a power source (and digital signal cabling) Use only the AC adapter supplied. Notes: - Do not over bend the cable or give excessive stress to the cable or sandwich the cables between covers.
- 8. Close the cover (a). 1) Insert the three hooks into the slit. 2) Push slowly both sides of the cover until the three hooks click into place. When you use a Digital signal cable (to be purchased separately), plug the Digital signal cable’s connector into DVI-D input connector and fix with screws each side. Digital signal cable (to be purchased separately) - When you use only the digital signal cable, it allows you to remove the analog signal cable. (Disconnect by loosening the screws each side.
Connecting the monitor and turning the monitor on and off Digital RGB connection Connecting the monitor to a computer (PC etc.) Connecting the monitor to a computer via a Digital signal cable (to be purchased separately) Before connecting the cable, ensure that both the monitor and computer are switched off. Analog RGB connection Connect this device’s analog signal cable to the computer (PC etc.) Before connecting the cable, ensure that both the monitor and computer are switched off.
Turning the power on Connecting a USB device 1. Press the monitor's POWER button. 2. Turn on the computer. The power LED will be lit green, and the screen will display an image. This monitor can be used with hubs which use the USB standard (Rev. 1.1). Downstream (2 ports) USB devices such as keyboard and mouse can be connected here. Up to 100mA of power is able to be supplied per port. Devices requiring more than 100mA cannot be connected.
Connecting the monitor and turning the monitor on and off For Windows98 Installing set-up information and the ICC profile (Windows) Installing monitor set-up information into Windows98, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the floppy disk drive is "A drive". Depending on the computer or OS, it may be necessary to use the computer to operate the installation of monitor set-up information etc.
For Windows2000 5. Select the monitor details from the list, then click [Next], [Next], and [Finish]. If the "Add new Hardware Wizard" appears, repeat the installation commands beginning from 2 above. 6. Remove the Utility Disk from the A drive. Installing monitor set-up information into Windows2000, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the floppy disk drive is "A drive". If the "Add New Hardware Wizard" has not appeared: 1.
Connecting the monitor and turning the monitor on and off Information about the ColorSync profile (MacOS) About the ColorSync profile ColorSync is the Apple Corporation's color management system and is a function that enables color resolution to be realized when used with a compatible application. A ColorSync profile describes the color characteristics of the LCD monitor. Notes: - This monitor's ColorSync profile works with MacOS8.5 or above.
For analog signal 1. First perform an automatic adjustment. (p. 21) 2. Perform manual adjustment where necessary. (p. 22) For digital signal The monitor can generally be used without adjustment,if neccessary perform manual adjustment.(p.25) Automatic adjustment This monitor can perform backlight brightness control automatically depending on an ambient brightness sensed by BRIGHT SENSOR. Note: - All adjustment will be retained even after turning the power off.
Adjusting the screen display Setting color mode ADJUSTMENT menu reset Color tone can be set as below. Resetting ADJUSTMENT Menu(for Analog signal) The values in ADJUSTMENT menu can be returned to their original ex-factory values. STD Displays image with the color tone results from original scheme of liquid crystal panel 1. Turn on the monitor power. 2. Press the MENU button and the button simultaneously. When [RESET] appears on the screen, the reset is complete.
How to Adjust 1. Press the MENU button. The ADJUSTMENT Menu will be displayed. Automatic screen adjustment CLOCK,PHASE,H-POS,V-POS in ADJUSTMENT can be adjusted automatically. Note: - When setting up this monitor for the first time or after having any change on an aspect of the current system, perform this Automatic Screen Adjustment,before use. On Screen Display for the automatic adjustment 2. Press the button. The screen will become dark and [ADJUSTING] will be displayed.
Adjusting the screen display (when using an analog signal) CLOCK The figures below demonstrate how to adjust so that vertical stripes disappear.( buttons) Manual screen adjustment Adjustment can be made using On Screen Display (OSD) Menu provided. On Screen Display for adjustment If you are using Windows, open the Adjustment Pattern on the accompanying Utility Disk. (p. 21). If your system is not Windows, you can not use the Adjustment Pattern.
GAIN CONTROL Menu WHITE BALANCE Menu MANUAL: Individual menu options are manually adjusted. AUTO: Auto Gain Control* capable of adjusting [BLACK LEVEL], [CONTRAST] automatically. Adjust manually as the needs arise after Automatic adjustment. Notes: - On settings other than [STD] not all graduations can be displayed. To display all graduations, set to [STD]. - Use the buttons to select [COOL], [·], [STD], [·], [WARM] or [USER].
Adjusting the screen display (when using an analog signal) MODE SELECT Menu LANGUAGE You can chose the language used in OSD Menu. 1. Press the button. Language Selection Menu (LANGUAGE) will appear. 2. Chose the desired language by SELECT button. 3. Press MENU button or the button, and Language Selection Menu will disappear. Notes: - Depending on the resolution of the input signal, even if menu options can be selected, the display may not change.
WHITE BALANCE Menu Screen adjustment Adjustments can be made using the On Screen Display (OSD) Menu provided. On Screen Display for adjustment If you are using Windows, open the Test Pattern on the accompanying Utility Disk. (p. 21). If your system is not Windows, you can not use the Test Pattern. Therefore display an image that makes the entire screen light and adjust it through checking visually its actual tone. Notes: - On settings other than [STD] not all graduations can be displayed.
Adjusting the screen display (when using a digital signal) MODE SELECT Menu Notes: - Depending on the resolution of the input signal, even if menu options can be selected, the display may not change. - To choose a menu option: SELECT button - When adjustment complete: MENU button OSD H-POSITION (OSD horizontal position) The position of the OSD display can be moved to the left and right. ( buttons) OSD V-POSITION (OSD vertical position) The position of the OSD display can be moved buttons) up and down.
Monitor care The monitor's florescent tubes have a limited life span. - If the screen darkens, persistently flickers or does not light up, it may be necessary to replace the florescent tube unit. Please inquire at the shop where you purchased the monitor or your nearest Sharp authorized Service Center. (Never attempt this replacement on your own.) - In the initial period of use, due to the characteristics of florescent tubes the screen may flicker. (This is not a malfunction.
Specifications Product specifications Dimensions (Units: mm) LCD panel 15 inch type (Diagonal 38cm) Advanced Super-V and Anti-Glare Low Reflection TFT LCD module Resolution (max.) XGA, 1,024 x 768 pixel Display colors (max.) Approx. 16.77 million color (8 bit) Brightness (max.) 220 cd/m2 Pixel pitch 0.297(H) x 0.297 (V)mm Contrast ratio 350:1 Viewing angle Horizontal 170° / Vertical 170° Viewable area Horizontal 304.1 x Vertical 228.1 mm Video signal Analog: Analog RGB (0.
Relevant signal timings (analog) Display mode VESA 640x480 800x600 1024x768 US TEXT Power Macintosh series - - - 720x400 640x480 832x624 1024x768 Hsync 31.5kHz 37.9kHz 37.5kHz 35.1kHz 37.9kHz 48.1kHz 46.9kHz 48.4kHz 56.5kHz 60.0kHz 31.5kHz 35.0kHz 49.7kHz 60.2kHz English Specifications Relevant signal timings (digital) Vsync Dot frequency 60Hz 72Hz 75Hz 56Hz 60Hz 72Hz 75Hz 60Hz 70Hz 75Hz 70Hz 66.7Hz 74.6Hz 75Hz 25.175MHz 31.5MHz 31.5MHz 36.0MHz 40.0MHz 50.0MHz 49.5MHz 65.0MHz 75.0MHz 78.
Specifications The analog signal input connector pin Power management (Mini D-sub connector with 15 pins) Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 The monitor is based on the VESA DPMS and the DVI DMPM standards. To activate the monitor's Power Management function, both the video card and the computer must conform to the VESA DPMS standard and the DVI DMPM standard. Function Red video signal input Green video signal input Blue video signal input N.C.
3) While lifting AC adapter’s cord root side, slide it toward the round opening, and then pull toward you to remove AC adapter. An arm or stand based on the VESA standard (purchased separately) can be attached to the monitor. Procurement of the arm or stand is at the customer's discretion. Arms or stands able to be used Attachments must satisfy the following.
Instructions for attaching a VESA compliant arm 6. Attach the arm or the stand to the monitor with four screws. Caution - The screws used to attach the arm should be M4 screws with a length of 4 mm ~ 6 mm protruding from the surface to be attached. Using different screws could lead to a malfunction or may lead to the monitor falling off,internal damage,personal injury. Screw used to attach arm Arm Part of monitor to which arm is attached 7.
SHARP CORPORATION © 2001 SHARP CORPORATION 01J DSN1 TINSM1028MPZZ (1)
