LCD MONITOR LCD FARBMONITOR MONITEUR LCD MONITOR LCD LL-T1810A OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUALE D’USO
Table of Contents Notice for Users in the USA ............................................................................................................................ 4 TCO'99 ............................................................................................................................................................ 5 Notice for Users in Europe ..............................................................................................................................
Notice for Users in the USA FCC Statement WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire.
Notice for Users in Europe This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG.
Notice for Users in the UK FOR CUSTOMERS IN U.K. IMPORTANT The wires in this mains lead are coloured in accordance with the following code : GREEN-AND-YELLOW : Earth BLUE : Neutral BROWN : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows.
Tips and safety precautions - - - - - - The Power Cord - Do not damage the power cord nor place heavy objects on it, stretch it or overly bend it. Also, do not add extension cords. Damage to the cord may result in fire or electric shock. - Use only the AC adapter supplied with the monitor. Using an AC adapter other than that supplied may lead to fire. - Insert the power plug directly into the AC outlet.
Product description Front view Power button (p. 14) This button switches the monitor ON and OFF. Control Panel Power LED (p. 14) Green light: In use Orange light: Power saving mode or signal failure Lamp off: Power OFF buttons When the On Screen Display (OSD) Menu is displayed: These buttons are used to increase or decrease the value of a selected option. (p. 19) When the OSD Menu is not displayed: These buttons are used to adjust backlight brightness (p. 18). SELECT button (p.
Product description Front view Ventilation Note: Never block the ventilation openings as this may lead to openings overheating inside the monitor and result in malfunction. Power terminal (p. 12) Remove the cover to see the power terminal. The AC adapter is connected here. Ventilation openings INPUT 2 terminal and USB port Remove the cover to view the computer input terminal (INPUT 2) and USB port. INPUT 2 terminal (p. 13) A second computer can be connected here. USB port: Downstream (Port 2) (p.
Connecting the monitor and turning the monitor on and off 5. Connect power cord to AC adapter. Connecting the monitor to a power source Use only the AC adapter supplied. 1. Remove the stand cover. Power cord (Rear View) Stand cover Lift one side Fitting the AC adapter inside the stand Wind the cord 2. Remove the cover. Cover Place adapter inside stand cavity. 6. Replace stand cover. 3. Connect the AC adapter to the monitor's power terminal. Stand cover Power terminal Run cord through hole.
Connecting the monitor and turning the monitor on and off 2. Connect the RGB signal cable (purchased separately) to the INPUT 2 terminal. Connecting the monitor to a computer (PC etc.) INPUT 2 terminal When connecting, ensure that both the monitor and computer are switched off. RGB signal cable (purchased separately) Firmly insert the analog RGB output terminal (mini D-sub 15 pin with 3 rows) then tighten the screws each side. To the computer's RGB output terminal 3. Replace the cover.
Connecting the monitor and turning the monitor on and off 2. Connect the USB cable. Changing between input terminals (INPUT 1 ↔ 2) USB port: Downstream (2 ports) When connected to two computers, use the INPUT button to switch between input signal terminals (i.e. to choose which computer's screen you want displayed.) USB port: Upstream (1 port) 3. Replace the cover. Turning the power on When connecting, ensure that both the monitor and computer are switched off.
Connecting the monitor and turning the monitor on and off 7. Check that the monitor details are displayed, then click [Apply]. 8. Click [OK], and close the window. 9. Remove the Monitor Settings Adjustment Disk from the A drive Installing set-up information and the ICC profile Depending on the computer or OS, it may be necessary to use the computer to operate the installation of monitor set-up information etc. If so, follow the steps below to install the monitor set-up information.
Connecting the monitor and turning the monitor on and off Installing the ICC profile Installing the monitor’s ICC profile. (If the set-up information has already been installed, so too has the profile, and there is no need to install it.) This explanation assumes that the floppy disk drive is "A drive". 8. When [Models] is displayed, click on [Have Disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK]. 9.
Adjusting the screen display Adjustment lock function If necessary, the screen can be adjusted as follows. Automatic screen adjustment (p. 18) The CLOCK, PHASE, H-POS (horizontal positioning) and V-POS (vertical positioning) functions can be adjusted automatically. Adjustment of backlight (p. 18) Brightness of backlight can be adjusted. Manual adjustment (p. 19) Fine adjustments can be made using the On Screen Display (OSD) Menu. By disabling the control buttons (i.e.
Adjusting the screen display Adjusting the screen automatically Automatic screen adjustment 1. Press the MENU button. The ADJUSTMENT Menu will be displayed. Options in MENU 1 (ADJUSTMENT) can be adjusted automatically (CLOCK, PHASE, H-POS, VPOS). Note: - When setting up the monitor or a connected computer for the first time, connecting an additional computer or after having changed an aspect of the current system, perform an automatic screen adjustment before use 2. Press the button.
Adjusting the screen display MENU 1: ADJUSTMENT Manual screen adjustment Fine adjustments can be made using the On Screen Display (OSD) Menu provided.
Adjusting the screen display MENU 3: WHITE BALANCE WHITE BALANCE can be adjusted as necessary. (As adjustments are made before shipment, there is no real necessity for further alteration.) MENU 2: GAIN CONTROL BRIGHT (brightness) and CONT (contrast) are optimized before shipment, but depending on the type of computer being used, further adjustment may be necessary. Notes: - Not all graduations for COOL and WARM can be displayed. To display all graduations, set to STD.
Adjusting the screen display MENU 4: MODE SELECT The resolution can be adjusted Notes: - To choose a menu option: SELECT button - When adjustment complete: MENU button INPUT (Input mode) The input mode can be set ( buttons) VESA: VESA mode MAC: Power Macintosh mode 400 LINES (degree of resolution) You can specify the horizontal resolution of a 400-line screen when using US text, etc. ( buttons) 640 640 X 400 dot mode 720 720 X 400 dot mode (US text etc.
Monitor care and repair Monitor care Troubleshooting Always remove the plug from the AC outlet when cleaning the monitor. If you think the monitor may be faulty, please check the following points before taking it to be repaired. If afterwards it still does not work, please contact the shop where you purchased the monitor or your nearest Sharp authorized Service Center. Cabinet and control panel section Use a soft dry cloth to lightly wipe away any grime from the cabinet and control panel.
Specifications Product specifications Power supply AC100-240V (Use special AC adapter) Temperature of operating environment 5 - 35°C Power consumption 54W (4.5W when in power-saving mode) Dimensions (W x D x H, excluding rubber base) 443 mm x 218 mm x 464 mm Weight Approx. 10.4 kg (excluding AC adapter) LCD display 18.1 inches (46 cm measured diagonally) Super-V and Anti Glare Low Reflection TFT LCD module Resolution (max.) SXGA 1280 x 1024 pixels Displayable colors (max.) 16.
Specifications Signal timings Display mode Hsync Vsync Dot frequency VESA US text Power Macintosh series Sun Ultra series Notes: - All are compliant only with non-interlace. - Frequencies for Power Macintosh and the Sun Ultra series are reference values. - If the monitor is receiving timing signals that are not compatible, [OUT OF TIMING] will appear. Follow your computer’s instruction manual to set the timing to be compatible with the monitor.
Specifications Standards and compatibility DDC (Plug & Play) Power management The monitor is based on VESA DPMS (Display Power Management Signaling). To activate the monitor's Power Management function, both the video card and the computer must conform to the VESA DPMS standard. This monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for carrying out Plug & Play functions on the monitor or PC.
Instructions for attaching a VESA compliant arm 5. Remove the four screws and then remove the stand from the monitor. An arm or stand based on the VESA standard (purchased separately) can be attached to the monitor. Procurement of the arm or stand is at the customer's discretion. Four screws Arms or stands able to be used Attachments must satisfy the following.
SHARP CORPORATION © 2001 SHARP CORPORATION 01C DSN2 TINSM1017MPZZ (2)
