LCD MONITOR TOUCH DISPLAY DRIVER 2 for Mac OPERATION MANUAL Applicable models LL-P202V/LL-S242A Version 1.
Contents Introduction.......................................................................3 System Requirements...................................................3 Setting up the Computer..................................................4 Install.............................................................................4 Touch Panel Settings........................................................5 How to configure settings..............................................5 Calibration.......................
Introduction System Requirements The touch display driver 2 is a program that enables you to use the touch panel to operate the computer that is connected to the touch panel. To use the touch panel, the touch panel must be connected to a computer, and the touch display driver 2 must be installed on the computer. OS Mac OS X v10.7, Mac OS X v10.8, Mac OS X v10.
Setting up the Computer Install Caution • To install, an administrator name (user name) and password are required. • If an older version of the touch display driver 2 is installed, remove (uninstall) the old version before installing the touch display driver 2. (See page 12.) • Do not touch the touch panel when connecting the USB cable. If you touch the touch panel, it will lead to a malfunction. In this case, disconnect and then reconnect the USB cable. 1. Start your computer. 2.
Touch Panel Settings The touch display driver 2 starts automatically and the icon ( ) appears on the menu bar. Caution • If LL-P202V and LL-S242A are connected at the same time, a screen for selecting the model will appear each time you select a setting. • Depending on the connected model, the screen image is different. • Default value may vary according to the models. How to configure settings nConfiguring settings from the menu bar 1. Click the touch display driver 2 icon ( 2.
Touch Panel Settings nSettings when two devices are connected at the same time • If two displays of the same model are connected, touch operation will only be enabled on one model. • If LL-P202V and LL-S242A are connected at the same time, select the model to apply the touch panel settings to. * Two models cannot be set at the same time. 1. Click “System Preferences” from the Apple menu ( ). 2. Click “SharpTouchDisplay2”. The “Device Selection” screen appears. 3.
Touch Panel Settings Calibration If black bands appear at the top and bottom or left and right of the screen, perform position adjustment so that the mouse cursor correctly moves to the point that is touched. * If black bands appear both at the top and bottom and at the left and right, the touch position is not correct. In this case, change the display. nCalibration Method Follow the steps below to configure the setting. 1. Click the touch display driver 2 icon ( 2. Click “Calibration”.
Touch Panel Settings Properties Settings for the touch action can be configured in the properties. nDouble Click Range Set the range over which the position can shift between the first touch and the second touch and still be recognized as a doubleclick (“Narrow” (8 pixels) to “Wide” (64 pixels)). To return the setting to the default setting, click “Default” (32 pixels). nDouble Click Speed Set the time that is recognized as a double-click.
Touch Panel Settings nSecondary click You can set press and hold to be recognized as a secondary click.* Enable press and hold for secondary click When the checkbox is selected, press and hold is recognized as a secondary click. Press and Hold Duration Set the time until press and hold is recognized as a secondary click (“Short” (0.5 sec) to “Long” (1.5 sec)).
Pen Settings (LL-P202V Only) Digitizer pen Settings for the digitizer pen can be configured. nButton Settings Assign functions to the function buttons of the digitizer pen. The factory default settings are shown below.
Pen Settings (LL-P202V Only) nPressure Settings Configure the pressure settings of the digitizer pen. Pen pressure Set pen pressure mode of the digitizer pen to Valid/Invalid. Pen pressure level adjustment Set the pen pressure at which the touch panel recognizes the pen. Pen pressure level test Shows the pen pressure level.
Uninstall Caution • To uninstall, an administrator name (user name) and password are required. 1. Disconnect the USB cable. 2. Execute uninstall. (1) Double-click the “TouchDisplay” folder, and then double-click the “Mac” folder. (2) Double-click “SharpDisplayDriver2 Uninstaller.app”. (3) Click “Uninstall”. • If a screen prompting you to enter the name and password appears, enter the name and password of the administrator and click “OK”. 3. When the uninstall finished screen appears, click “Quit”.
Touch Action Touch modes are finger/pen mode, pen-only mode, and fingeronly mode. The default setting is finger/pen mode. TIPS • To change the touch mode, see the manual for the LCD MONITOR (LL-P202V/LL-S242A). • Select the action to be used in Function Setting. (See page 9.) • When using your finger or a touch pen, you cannot move the cursor without tapping the screen. nCommon finger and pen actions Tap Same action as left-clicking a mouse. Touch with your finger/pen.
Touch Action nFinger actions TIPS • The screen may not respond correctly in the following cases: Touching is too quick The distance between the two points is too short • Operation with the touch pen is not possible. Pinch with two fingers Use in a screen that is capable of reduction/enlargement. Touch the screen with two fingers and move your fingers closer together to reduce the view, or apart to enlarge the view. Click or tap with two fingers Same action as a secondary click.
Touch Action Scroll left or right with two fingers / Swipe with two or three fingers Use cross page swipe. Swipe left or right with three or four fingers Move an application to the front. Swipe up with three or four fingers Display Mission Control. Swipe left from the right edge with two fingers Display the notice center. Tap with three fingers Check the tapped text in a dictionary or other resource. Swipe down with three or four fingers Display Application Exposé.
Touch Action Spread with thumb and three fingers Touch the screen with 4 fingers, and move your thumb and 3 fingers apart to show the desktop.
LL-P202V/LL-S242A V1.