LQ201U1LW01 TFT-LCD Module (Model Number: LQ201U1LW01) Specifications Spec No.
PREPARED BY : DATE SPEC No. LD-14115 FILE No. ISSUE : Feb.25.2002 APPROVED BY : DATE PAGE : 24 pages TFT LCD DEVELOPMENT GROUP APPLICABLE GROUP SHARP CORPORATION TFT Liquid Crystal Display Group SPECIFICATION DEVICE SPECIFICATION TFT-LCD Module MODEL No. LQ201U1LW01 □ CUSTOMER'S APPROVAL DATE BY PRESENTED BY M.
RECORDS OF REVISION LQ201U1LW01 SPEC No. DATE No. LD-14115 Feb. 25.
LD-14115-1 1. Application This specification applies to the color 20.1 UXGA TFT-LCD module LQ201U1LW01. ◎These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP.
LD-14115-2 3. Mechanical Specifications Parameter Display size Specifications Unit 51 (Diagonal) cm 20.1 (Diagonal) Inch Active area 408.0 (H)×306.0 (V) mm Pixel format 1600 (H)×1200 (V) Pixel (1 pixel＝R＋G＋B dots) Pixel pitch 0.255(H)×0.255 (V) Pixel configuration R,G,B vertical stripe Display mode Normally black Unit outline dimensions *1 436(W)×335 (H)×27.5 (D) Mass 3.8 (MAX) Surface treatment Anti-glare And hard-coating 2H *1.Note: excluding back light cables.
LD-14115-3 4. Input Terminals 4-1. TFT-LCD panel driving CN7A,CN7B (Interface signals and +12VDC power supply) Using connectors ：DF19G-20P-1H (Hirose Electric Co., Ltd.) Corresponding connectors ：DF19G-20S-1C (Hirose Electric Co., Ltd.) DF19G-20S-1F (Hirose Electric Co., Ltd.) Using LVDS receiver：Contained in a control IC Corresponding LVDS transmitter：THC63LVDM83R(Thine) or compatible CN７A Pin No.
LD-14115-4 【Note2】SELLVDS(Thine:THC63LVDM83R) Transmitter =L Pin No Data R0(LSB) 51 TA0 R1 52 TA1 R2 54 TA2 R3 55 TA3 R4 56 TA4 R5 3 TA5 G0(LSB) 4 TA6 G1 6 TB0 G2 7 TB1 G3 11 TB2 G4 12 TB3 G5 14 TB4 B0(LSB) 15 TB5 B1 19 TB6 B2 20 TC0 B3 22 TC1 B4 23 TC2 B5 24 TC3 (NA) 27 TC4 (RSV1) 28 TC5 DE 30 TC6 R6 50 TD0 R7(MSB) 2 TD1 G6 8 TD2 G7(MSB) 10 TD3 B6 16 TD4 B7(MSB) 18 TD5 (NA) 25 TD6 SELLVDS =H R2 R3 R4 R5 R6 R7(MSB) G2 G3 G4 G5 G6 G7(MSB) B2 B3 B4 B5 B6 B7(MSB) (NA) (RSV1) DE R0(LSB) R1 G0(LSB) G1 B0(LSB) B
LD-14115-5 4-2 Interface block diagram Using receiver：Contained in a control IC.
LD-14115-6 < SELLVDS= Low > 1 cycle CKAIN+ CK^AINRAIN0+ RAIN0- RA1 RA0 GA0 RA5 RA4 RA3 RA2 RA1 RA0 GA0 GA2 GA1 BA1 BA0 GA5 GA4 GA3 GA2 GA1 BA1 BA3 BA2 DEA NA NA BA5 BA4 BA3 BA2 DEA RA7 RA6 NA BA7 BA6 GA7 GA6 RA7 RA6 NA RAIN1+ RAIN1RAIN2+ RAIN2RAIN3+ RAIN3- Tcsq CKBINCKBIN+ RBIN0+ RBIN0- RB1 RB0 GB0 RB5 RB4 RB3 RB2 RB1 RB0 GB0 GB2 GB1 BB1 BB0 GB5 GB4 GB3 GB2 GB1 BB1 BB3 BB2 DEB RSV1 NA BB5 BB4 BB3 BB2 DEB RB7 RB6 NA BB7 BB6 GB7 G
LD-14115-7 < SELLVDS= High > 1 cycle CKAIN+ CKAINRAIN0+ RAIN0- RA3 RA2 GA2 RA7 RA6 RA5 RA4 RA3 RA2 GA2 GA4 GA3 BA3 BA2 GA7 GA6 GA5 GA4 GA3 BA3 BA5 BA4 DEA NA NA BA7 BA6 BA5 BA4 DEA RA1 RA0 NA BA1 BA0 GA1 GA0 RA1 RA0 NA RAIN1+ RAIN1RAIN2+ RAIN2RAIN3+ RAIN3- Tcsq CKBINCKBIN+ RBIN0+ RBIN0- RB3 RB2 GB2 RB7 RB6 RB5 RB4 RB3 RB2 GB2 GB4 GB3 BB3 BB2 GB7 GB6 GB5 GB4 GB3 BB3 BB5 BB4 DEB RSV1 NA BB7 BB6 BB5 BB4 DEB RB1 RB0 NA BB1 BB0 GB1 G
LD-14115-8 4-2. Back light driving CN 1, 2, 3 (Upside) CN 4, 5, 6 (Downside) The module-side connector The user-side connector : BHSR－02VS－01 : SM02B－BHSS－1－TB (JST) (JST) Pin no. symbol I/O Function 1 Ｖhigh I Power supply (High voltage side) 2 Ｖlow I Power supply (Low voltage side) 1pin ＣＮ１ ＣＮ２ ＣＮ３ 1pin 1pin TFT LCD 1pin ＣＮ４ ＣＮ５ ＣＮ６ 1pin 1pin 5. Absolute Maximum Ratings Parameter Symbol Condition Ratings Unit Remark SELLVDS VI Ta=25℃ －0.3 ～ +3.6 Ｖ +12.
LD-14115-9 6. Electrical Characteristics 6-1. TFT-LCD panel driving Ta＝25℃ Min. +11.4 Typ. +12.0 Max. +12.6 Unit V Remark 【Note1】 Icc － 390 600 mA 【Note2】 Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (Low) VRF VIL VIH IIL － 0 +2.7 － － － － － 100 +0.6 +3.3 500 mVp-p V V μA Input current (High) IIH － － 100 μA Output voltage (Low) Output voltage (High) VOL VOH － － － 0.
LD-14115-10 6-2. Back light driving The back light system is an edge-lighting type with six CCFTs (Cold Cathode Fluorescent Tube). The characteristics of the lamp are shown in the following table. The value mentioned below is at the case of one CCFT. CCFT Model Name：KTBE26MSTF‐A424NE209‐Z‐3（STANLEY.ELECTRIC.CO.,LTD） Parameter Symbol Min. Typ. Max. Unit Remark Lamp current range IL 3.0 6.0 6.5 mArms 【Note1】 790 Vrms Ta=25℃ Lamp voltage VL － － 4.
LD-14115-11 7. Timing characteristics of input signals 7-1-1. Timing characteristics Clock Data enable Parameter Symbol Min. Typ. Max. Unit Frequency 1/Tc 60.0 81.0 85.0 MHz Skew Tcsq –4 0 4 ns TH 830 1080 1600 clock 10.0 13.3 － µs Horizontal period signal Horizontal period (High) THd 800 800 800 clock Vertical period TV 1205 1250 2000 line 12.1 16.
LD-14115-12 7-2 Input Data Signals and Display Position on the screen Graphics and texts can be displayed on a 1600 × 3× 1200 dots panel with 16M colors by supplying 48 bit data signal (8bit/color [256 gray scales] × 3 × 2 pixels). RA GA BA RB GB BB DA(1,1) DB(2,1) Two pixel-data are sampled at the same time.
LD-14115-13 8.
LD-14115-14 9. Optical Characteristics Ta=25℃, Vcc =+12V Parameter Viewing Vertical Angle range Horizontal Symbol Condition Min. Typ. Max. Unit Remark θ11 CR≧10 70 85 － Deg. 【Note1,4】 θ12 70 85 － Deg θ21,θ22 70 85 － Deg. － 350 － ＣＲ Contrast ratio θ=0° 【Note2,4】 Rise τd － 5 25 ｍｓ Decay τr － 20 50 ｍｓ Chromaticity of Wx 0.283 0.313 0.343 － white Wy 0.299 0.329 0.359 － Chromaticity of Rx 0.608 0.638 0.668 － red Ry 0.309 0.339 0.
LD-14115-15 【Note1】Definitions of viewing angle range: 【Note2】Definition of contrast ratio: The contrast ratio is defined as the following. Luminance (brightness) with all pixels white Contrast Ratio (CR) ＝ Luminance (brightness) with all pixels black 【Note3】Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white". 【Note4】This shall be measured at center of the screen.
LD-14115-16 10. Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) Since the front polarize is easily damaged, pay attention not to scratch it. d) Since long contact with water may cause discoloration or spots, wipe off water drop immediately.
LD-14115-17 12．Reliability test items No. Test item Conditions 1 High temperature storage test Ta=60℃ 240h 2 Low temperature storage test Ta=-25℃ 240h 3 High temperature Ta=40℃ ; 95%RH & high humidity operation test (No condensation) High temperature operation test Ta=50℃ 4 240h 240h (The panel temp. must be less than 60℃) 5 Low temperature operation test Ta=0℃ 6 Vibration test Frequency : 10～57Hz/Vibration width (one side) : 0.075mm (non- operating) 240H : 58～500Hz/Gravity : 9.
LD-14115-18 13．Others 1) Lot No. and indication Bar Code Label: P R A H S How to express Lot No. Model No. LQ201U1LW01 Bar Code(Lot No.) 23 XXXXXX MADE IN JAPAN Lot No. A production year (the last figures of the Christian Era) Serial No. A production month (1～9,X,Y,Z) 2) Packing Label ① Model No. (LQ201U1LW01) ② Lot No.
LD-14115-19 14．Carton storage condition Temperature 0℃ to 40℃ Humidity 95%RH or less Reference condition : 20℃ to 35℃ , 85%RH or less (summer) : 5℃ to 15℃ , 85%RH or less (winter) ・the total storage time (40℃,95%RH) : 240H or less Sunlight Be sure to shelter a product from the direct sunlight. Atmosphere Harmful gas, such as acid and alkali which bites electronic components and/or wires, must not be detected.
LD-14115-20
LD-14115-21
LD-14115-22
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED.
