MINIDYSK MD-MT88H/MD-MT99H INSTRUKCJA OBSŁUGI
UWAGA: OPISYWANE URZĄDZENIE JEST ZGODNE Z DYREKTYWAMI UNII EUROPEJSKIEJ NR 89/336/EEC I 73/23/EEC Z UWZGLĘDNIENIEM POPRAWKI 93/68/EEC.
OSTRZEŻENIE: URZĄDZENIE NALEŻY CHRONIĆ PRZED ZALANIEM I WILGOCIĄ. OSTRZEŻENIE: SŁUCHANIE MUZYKI PRZY USTAWIONYM MAKSYMALNYM POZIOMIE GŁOŚNOŚCI PRZEZ DŁUŻSZY CZAS MOŻE DOPROWADZIĆ DO USZKODZENIA SŁUCHU. OPISYWANE URZĄDZENIE SPEŁNIA STOSOWNE NORMY, JEŚLI JEST UŻYWANE Z ORYGINALNYMI SŁUCHAWKAMI FIRMY SHARP (NUMER MODELU RPOH0011AWZZ). W PRZYPADKU USZKODZENIA, PROSIMY ZAMÓWIĆ ODPOWIEDNIE SŁUCHAWKI.
UWAGA: URZĄDZENIE LASEROWE KLASY 1 PONIEWAŻ WYKORZYSTYWANA W ODTWARZACZU WIĄZKA LASEROWA JEST NIEBEZPIECZNA DLA OCZU, NIE WOLNO DEMONTOWAĆ JEGO OBUDOWY. NAPRAWĘ SPRZĘTU NALEŻY ZLECAĆ WYKWALIFIKOWANYM PRACOWNIKOM SERWISU.
Parametry diody laserowej: ! Materiał GaAlAs ! Długość fali: 785 nm ! Czas trwania impulsu: Tryb odczytu: 0,8 mW - emisja ciągła Tryb zapisu: maks. 10 mW – 0,5 s Minimalny czas powtarzania cyklu: 1,5 s OSTRZEŻENIE: POD POKRYWĄ ZNAJDUJE SIĘ NIEWIDZIALNE PROMIENIOWANIE LASEROWE. NIE WOLNO PATRZEĆ W WIĄZKĘ BEZPOŚREDNIO ANI PRZY UŻYCIU PRZYRZĄDÓW OPTYCZNYCH.
Wprowadzenie Dziękujemy za zakup urządzenia firmy SHARP. Przed jego włączeniem prosimy o zapoznanie się z niniejszą instrukcją, która ułatwi obsługę opisywanego sprzętu. Wprowadzenie 1 - Wprowadzenie / Spis treści - Spis treści # Wprowadzenie Ważnie informacje .................................................. 2 Akcesoria................................................................. 2 Akcesoria opcjonalne............................................. 2 Nazwy przycisków i wskaźników ....................
Ważnie informacje model MD-MT99H. Od modelu MD-MT88H odróżnia go jedynie kształt niektórych przycisków, pilot oraz elementy wyposażenia standardowego. ! Patenty amerykańskie i zagraniczne są na licencji Dolby Laboratories Licensing Corporation. ! Zasilacza sieciowego dostarczonego z opisywanym urządzeniem nie wolno używać z innym sprzętem. ! Przed ważnymi nagraniami należy przeprowadzić wstępny test, aby się upewnić, że żądany materiał będzie poprawnie nagrany.
Nazwy przycisków i wskaźników Wprowadzenie 3 - Nazwy przycisków i wskaźników - # Urządzenie główne 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. MD-MT88H/MD-MT99H Gniazdko 5V DC (patrz str. 7) Gniazdko OPTICAL/LINE IN (patrz str. 7, 8) Gniazdko MIC IN (patrz str. 23) Przycisk BASS (patrz str. 14, 34) Przycisk EDIT (patrz str. 21, 26, 33) Przycisk DISP (patrz str. 27, 33) Przycisk MODE/CHRG (patrz str. 10, 16, 17, 29, 32) Przycisk REC (patrz str. 9, 21) Przycisk wielofunkcyjny (patrz str.
12. 13. 14. 15. 16. 17. Wskaźnik głośności (patrz str. 9) Wskaźnik REC (patrz str. 9) Wskaźnik trybu długiego nagrywania (patrz str. 17) Wskaźnik trybu mono (patrz str. 17) Wskaźnik trybu odtwarzania ciągłego (patrz str. 16) Wskaźnik TOC (patrz str. 10) Wskaźnik SYNC (patrz str. 119) Wskaźnik trybu pracy z dyskiem Wskaźnik nazwy dysku (patrz str. 27) Wskaźnik nazwy utworu (patrz str. 27) Wskaźnik czasu pozostałego do końca nagrania (patrz str. 27) Wskaźnik całkowitej liczby utworów (patrz str.
Ostrzeżenia # Ważne # Przechowywanie urządzenia ! Przechodząc przez ulicę lub w pobliżu ruchu drogowego nie należy Urządzenia nie należy przechowywać w następujących miejscach: ! W miejscach wystawionych na długotrwałe bezpośrednie promieniowanie słoneczne (zwłaszcza w samochodach z zamkniętymi drzwiami i oknami), a także w pobliżu urządzeń grzewczych. (Obudowa może ulec odkształceniu lub odbarwieniu, a urządzenie może nie pracować poprawnie). ! W miejscach narażonych na kontakt z wodą.
Wkładanie minidysku Przesuń dźwignię OPEN, żeby otworzyć pokrywę. Unieś pokrywę. Włóż minidysk tak, jak zostało to pokazane na rysunku. Uwagi: ! Nie wolno umieszczać minidysków pod uchwytem. ! W razie odczuwania oporu przy wkładaniu minidysku nie należy Nagrywanie możliwe Nagrywanie niemożliwe Przystępując do nagrywania na minidysku upewnij się, że zaślepka zabezpieczająca znajduje się w odpowiednim położeniu. stosować siły, aby nie uszkodzić urządzenia.
Podłączenia Po dokonaniu odpowiednich podłączeń będziesz mógł przegrywać swoje ulubione kasety lub płyty kompaktowe na minidyski.
# Podłączenie urządzenia stereo wyposażonego w gniazda „DIGITAL OUT” lub „OPTICAL OUT” Do gniazdka elektrycznego w ścianie Do gniazda OPTICAL/LINE IN Do urządzenia stereo z gniazdem „DIGITAL OUT” Nagrywanie w systemie cyfrowym zapewnia lepszą jakość w porównaniu z połączeniem standardowym. Uwagi: ! Niektóre urządzenia audio nie mają gniazda DIGITAL OUT. Przed przystąpieniem do nagrywania należy to sprawdzić.
Nagrywanie 3 Przyciśnij przycisk ! lub ", by ustawić poziom głośności nagrywania. Poziom głośności nagrywania należy ustawić tak, by przy największej głośności źródła poziom nagrania mieścił się między -4 dB a 0 dB. Poziom głośności można ustawić co 1 dB w zakresie od +12 dB do -12 dB. - Nagrywanie - Podstawy obsługi Wskaźnik poziomu głośności. Wyłącz blokadę przycisków. Napęd minidysków nie działa, gdy przyciski są zablokowane.
Przy pomocy przycisku MODE/CHRG wybierz żądany tryb odtwarzania (patrz strona 17). (Nagrywanie stereo) (2 razy dłuższe nagrywanie) Naciśnij przycisk PLAY/PAUSE. ! W celu kontynuowania nagrania, ponownie przyciśnij przycisk PLAY/PAUSE. ! Przy każdym przerwaniu nagrywania numer utworu zwiększa się o jeden. (4 razy dłuższe nagrywanie (Nagrywanie mono) Zakończenie nagrania Naciśnij przycisk #/:OFF. 6 Naciśnij przycisk PLAY/PAUSE na nagrywarce, by zacząć nagrywanie.
Nagrywanie (ciąg dalszy) Aktualizacja danych zapisanych na minidysku 11 - Nagrywanie - Podstawy obsługi W trybie zatrzymania (STOP) naciśnij przycisk #/:OFF. Zasilanie wyłącza się po zaktualizowaniu danych zapisanych na minidysku. Spis treści („TOC”) Po każdym nagraniu lub edycji na wyświetlaczu pojawia się komunikat „TOC” (Table of Contents, spis treści). W celu zakończenia funkcji nagrywania lub edycji należy nacisnąć przycisk #/:OFF.
Zaślepkę zabezpieczającą przez skasowaniem należy przesunąć w kierunku strzałki. Minidysk będzie wówczas zabezpieczony przed przypadkowym skasowaniem zawartości. W przypadku dokonywania dalszych nagrań na takim minidysku należy przesunąć zaślepkę do pierwotnego położenia.
Odtwarzanie Kanał lewy - Odtwarzanie - Podstawy obsługi Kanał prawy Przed odtwarzaniem Wyłącz blokadę przycisków. Napęd minidysków nie działa, gdy przyciski są zablokowane. Urządzenie główne Uwaga: W modelu MD-MT88H należy podłączyć słuchawki bezpośrednio do gniazdka PHONES w urządzeniu głównym. 13 Szczegóły znajdują się na stronie 31.
Włóż dysk (patrz strona 6). Przyciśnij przycisk PLAY/PAUSE. W przypadku minidysków tylko do odczytu i minidysków zabezpieczonych przed zapisem odtwarzanie rozpocznie się automatycznie (funkcja autostart). Przerwanie odtwarzania. Naciśnij przycisk PLAY/PAUSE. W celu wznowienia odtwarzania naciśnij ponownie przycisk PLAY /PAUSE. Zakończenie odtwarzania Naciśnij przycisk #/:OFF.
Odtwarzanie zaawansowane # Odnajdywanie początku utworu Przejście do początku następnego utworu: W trakcie odtwarzania przyciśnij przycisk ". Użyteczne funkcje 15 - Odtwarzanie zaawansowane - Powrót na początek bieżącego utworu: W trakcie odtwarzania przyciśnij przycisk !. Odnajdywanie następnego utworu: Przyciśnij przycisk ", gdy urządzenie jest zatrzymane. Odnajdywanie następnego utworu: Przyciśnij przycisk !, gdy urządzenie jest zatrzymane.
# Odtwarzanie losowe lub ciągłe Odtwarzanie w kolejności losowej Powtarzanie utworów w kolejności losowej ! Powtarzanie wszystkich utworów 1! Powtarzanie jednego utworu Brak wskaźniOdtwarzanie normalne ka # Odtwarzanie z podwójną szybkością (tylko nagrania mono) Przyciśnij przycisk ENTER/SYNC podczas odtwarzania minidysku nagranego w trybie mono. ! Jeśli podczas szybkiego odtwarzania zacznie się utwór nagrany w trybie stereo, tryb szybkiego odtwarzania zostanie wyłączony.
Nagrywanie zaawansowane # Tryb długiego nagrywania 1 Tryb 2 lub 4 razy dłuższego nagrywania W trybie długiego nagrywania dostępny czas nagrania zostaje wydłużony dwu- lub czterokrotnie. Tryb stereo (brak specjalnego wskazania) Użyteczne funkcje Nagrywanie w trybie mono W trybie mono można dokonywać dwa razy dłuższe nagrania niż w trybie stereo. - Nagrywanie zaawansowane - Przyciśnij przycisk MODE/CHRG w trybie pauzy. Każdorazowe naciśnięcie przycisku powodowało zmianę trybu pracy.
stereofoniczne, dźwięki z prawego i lewego kanału są łączone. Mimo, że podczas nagrywania w słuchawkach słyszalny jest dźwięk stereo, nagranie będzie dokonane w trybie mono. ! Nagrań dokonanych w trybie 2 i 4 razy dłuższego trybie nagrywania nie można odtwarzać w urządzeniach, które tych trybów nie obsługują. W takich urządzeniach na wyświetlaczu pojawi się wskaźnik „LP” i dźwięk nie będzie słyszalny. (Sposób działania i zawartość wyświetlacza mogą być różne w zależności od używanego urządzenia.
Nagrywanie zaawansowane # Nagrywanie uruchamiane przez dźwięk odtwarzania (nagrywanie synchroniczne) Urządzenie automatycznie zaczyna nagrywanie lub przełącza się w tryb pauzy w nagrywaniu po rozpoznaniu dźwięku z urządzenia stereo (nagrywanie synchroniczne). 4 Wybierz punkt początkowy nagrania i naciśnij przycisk PAUSE. 5 7 - Nagrywanie zaawansowane - Użyteczne funkcje 6 19 Naciśnij przycisk PAUSE na urządzeniu stereo, by przełączyć je w tryb pauzy w odtwarzaniu.
# Rozpoczęcie nagrania w środku utworu (ścieżki) Istnieje możliwość skasowania części utworu i dokonania nowego nagrania. Wszystkie utwory następujące po nowo nagranym utworze zostaną skasowane. 1 Podczas odtwarzania naciśnij przycisk PLAY/PAUSE w tym momencie, od którego ma się rozpocząć nagranie. 2 Naciśnij przycisk REC. ! W celu przerwania operacji należy nacisnąć przycisk #/:OFF. Przyciśnij przycisk ENTER/SYNC.
Nagrywanie zaawansowane (ciąg dalszy) # Tworzenie własnych numerów utworów # Nagrywanie utworów jako jednego utworu Można w dowolnym miejscu tworzyć własne numery utworów. Po wyłączeniu funkcji automatycznego numerowania można nagrać większą liczbę utworów jako pojedynczy utwór. Podczas nagrywania należy nacisnąć przycisk REC w tym miejscu, w którym ma powstać numer utworu. Numer utworu zostanie zwiększony o jeden. W trybie pauzy w nagrywaniu lub podczas nagrywania... Przyciśnij przycisk EDIT.
! Podczas nagrywania, jeśli dokonywane jest odtwarzanie zaprogra- # Numery utworów 1. Numery utworów tworzone są automatycznie zawsze, gdy w trakcie nagrywania przez gniazdo analogowe wykryta zostanie cisza trwająca 1 sekundę lub dłużej (automatyczne numerowanie). Można nagrać kilka utworów jako jeden, po wyłączeniu funkcji automatycznego numerowania. mowane lub odtwarzane utwory wybierane są ręcznie, numery utworów na minidysku mogą się różnić od numerów utworów źródła nagrania.
Nagrywanie przez mikrofon Użyteczne funkcje 23 - Nagrywanie przez mikrofon - # Przygotowanie do nagrywania Mikrofon stereo (dostępny w sprzedaży) Do gniazda MIC IN MD-MT88H/MD-MT99H
Nagrywanie przez mikrofon Podczas nagrywania naciśnij przycisk PLAY/PAUSE. Włóż minidysk przeznaczony do nagrywania (patrz strona 6). Przyciśnij przycisk REC. ! W celu wznowienia nagrywania należy ponownie nacisnąć przycisk PLAY/PAUSE. Przy każdym przerwaniu nagrywania numer utworu zwiększa się o jeden. Zakończenie nagrania Przy pomocy przycisku ! lub " wyreguluj poziom głośności nagrywania (patrz strona 9). Naciśnij przycisk #/:OFF.
Nagrywanie przez mikrofon (ciąg dalszy) # Nagrywanie uruchamiane głosem (zsynchronizowane nagrywanie z mikrofonu) 1 2 Przyciśnij przycisk REC. Przy pomocy przycisku ! lub " wyreguluj poziom głośności nagrywania. Użyteczne funkcje 25 - Nagrywanie przez mikrofon - Wskaźnik poziomu głośności. 3 Przyciśnij kilkakrotnie przycisk MODE/CHRG, żeby wybrać tryb nagrywania (patrz strona 17). 4 Przy pomocy przycisku ENTER/SYNC ustaw czułość nagrywania.
# Odstępy między ścieżkami Przykład: ustawienie na „5 minut”. Podczas nagrywania przez mikrofon numery utworów tworzone są w regularnych odstępach (ustawienie domyślne: mniej więcej co 5 minut). Jeśli podczas nagrywania synchronicznego przez mikrofon wystąpi cisza trwająca 3 sekundy lub dłużej, urządzenie przełącza się w tryb pauzy w nagraniu i tworzy nowy numer utworu. Co 5 minut tworzone są automatyczne znaczniki numerów ścieżek.
Kontrola wskazań wyświetlacza # Sprawdzanie czasu, który upłynął od początku utworu i czasu pozostałego do końca utworu Podczas odtwarzania nacisnąć przycisk DISP. Użyteczne funkcje 27 - Kontrola wskazań wyświetlacza - Kolejne naciśnięcia przycisku powodują następujące zmiany wskazań na wyświetlaczu: A. Numer utworu B. Nazwa utworu # Sprawdzanie pozostałego czasu nagrania i całkowitego czasu odtwarzania W trybie STOP naciśnij przycisk DISP.
# Sprawdzanie stanu baterii (akumulatora) # Wskaźniki czasu odtwarzania poszczególnych utworów Gdy odtwarzanie jest zatrzymane, przyciśnij przycisk ! lub ", żeby wyświetlić numer utworu (ścieżki) i jego nazwę. Jak odczytywać wskaźnik baterii 2 Wysoki poziom naładowania Przyciśnij przycisk DISP, żeby wyświetlić czas trwania danego utworu. Czas odtwarzania ! Po każdym przyciśnięciu przycisku ! lub " wyświetlany będzie czas trwania poprzedniego lub następnego utworu.
Zasilanie z akumulatora # Ładowanie akumulatora Osłony pojemnika na baterie nie należy odginać zbyt mocno do tyłu. Jeśli po raz pierwszy używasz akumulatora, lub jeśli używasz go po raz pierwszy po długiej przerwie, pamiętaj, by naładować go całkowicie. (W modelu MD-MT88 akumulator jest elementem wyposażenia dodatkowego.) Użyteczne funkcje - Zasilanie z akumulatora - 1 2 3 Włóż akumulator. W ten sposób można ładować wyłącznie akumulatory AD-N70BT.
# Czas ładowania # Korzystanie z akumulatora lub baterii alkalicznej Wskazówki: ! Ładowanie należy przeprowadzać w zakresie temperatur od 5°C do 35°C (od 41°F do 95°F). ! Ładowanie można uznać za zakończone, jeśli po włączeniu zasilacza i przyciśnięciu przycisku CHRG/MODE wskaźnik „” nie pojawia się. ! Po zakończeniu ładowania urządzenie można zostawić w trybie ładowania. Ostrzeżenia: ! Należy stosować tylko akumulatory AD-N70BT. Innych baterii (niklowo-kadmowych, alkalicznych itp.) nie wolno ładować.
Blokada przycisków Przyciski można zablokować zabezpieczając w ten sposób urządzenie przed przypadkową zmianą ustawień. Pilot (tylko model MD-MT99H) Urządzenie główne - Blokada przycisków - Użyteczne funkcje Przesuń przełącznik HOLD w kierunku wskazywanym przez strzałkę. Przyciśnij przycisk HOLD i przytrzymaj przez 2 sekundy lub dłużej.
Zmiana ustawień standardowych # Dźwięk potwierdzający Gdy przycisk zostanie zwolniony, pojawi się napis „BEEP ON” lub „BEEP OFF” 2 Przy pomocy przycisku ! lub " wyświetl odpowiednie menu. 3 Kolejne elementy można wyświetlać przy pomocy przycisku MODE/CHRG. 4 Przyciśnij przycisk #/:OFF.
Nadawanie tytułu minidyskowi # Tworzenie nazw dysków i utworów Włóż do napędu minidysk, któremu chcesz nadać nazwę. Nazwy nie mogą być zapisywane na minidyskach przeznaczonych wyłącznie do odczytu. 1 Nadawanie nazwy dyskowi: Gdy minidysk jest zatrzymany, przyciśnij przycisk EDIT, żeby wybrać „DISC NAME”. 3 Nadawanie nazwy utworowi: W trakcie pauzy przyciśnij przycisk EDIT, żeby wybrać „TRACK NAME”. Kilkakrotnie naciśnij przycisk DISP, by wybrać rodzaj znaków.
7 8 Po wprowadzeniu całego tytułu naciśnij przycisk EDIT. Na wyświetlaczu pojawi się komunikat "TOC". W celu zapisania zmienionej treści na dysku naciśnij przycisk #/:OFF. ! Minidysku nie można wyjąć z urządzenia, dopóki na wyświetlaczu widoczny jest komunikat "TOC", który nie zniknie, dopóki zawartość dysku nie zostanie zaktualizowana. # Usuwanie pojedynczego znaku Przyciśnij przycisk VOL+ lub VOL-, żeby ustawić kursor na znaku, który ma zostać usunięty, a następnie przyciśnij przycisk BASS.
Nadawanie tytułu minidyskowi (ciąg dalszy) # Dodawanie znaków # Przenoszenie informacji tekstowych z innego mini- 1 Ustaw urządzenie w trybie wprowadzania znaków. 2 Przyciśnij przycisk VOL+ lub VOL-, żeby ustawić kursor na prawo od miejsca, w którym ma zostać wstawiony znak. Funkcje zaawansowane 35 - Nadawanie tytułu minidyskowi - (Wykonaj czynności od 1 do 2 ze strony 33.) 3 Wybierz znak, który ma zostać wprowadzony. 4 5 6 Przyciśnij przycisk ENTER/SYNC.
Włóż dysk źródłowy do napędu. 2 Gdy odtwarzanie będzie przerwane, przyciśnij przycisk EDIT, żeby wybrać „NAME STAMP”. 3 Przyciśnij przycisk ENTER/SYNC. Postępuj ostrożnie, żeby nie pomylić dysku źródłowego z docelowym. 6 Włóż do napędu dysk docelowy. 7 Przyciśnij przycisk ENTER/SYNC. Urządzenie zakończy nagrywanie informacji znakowych i zatrzyma się. Żeby anulować operację, przyciśnij przycisk #/:OFF. 4 Przyciśnij przycisk ENTER/SYNC.
Edycja nagranego minidysku Funkcje zaawansowane 37 - Edycja nagranego minidysku - # Usuwanie pojedynczego utworu # Natychmiastowe usuwanie wszystkich utworów 1 Rozpocznij odtwarzanie utworu, który ma zostać usunięty i przyciśnij przycisk PLAY/PAUSE. 2 Przyciśnij przycisk EDIT kilkakrotnie, żeby wybrać funkcję „ERASE”. 3 1 Gdy odtwarzanie jest przerwane, kilkakrotnie przyciskaj przycisk EDIT, żeby wybrać „ALL ERASE”. 2 Przyciśnij przycisk ENTER/SYNC. 3 Ponownie przyciśnij przycisk ENTER/SYNC.
# Podział utworu 1 Rozpocznij odtwarzanie drugiego utworu spośród dwóch sąsiednich, które mają zostać połączone i przyciśnij przycisk PLAY/PAUSE. 2 Przyciśnij przycisk EDIT kilkakrotnie, żeby wybrać funkcję „DIVIDE”. 2 Przyciśnij przycisk EDIT kilkakrotnie, żeby wybrać funkcję „COMBINE”. 3 Przyciśnij przycisk ENTER/SYNC. 3 Przyciśnij przycisk ENTER/SYNC. ! Żeby anulować operację, przyciśnij przycisk #/:OFF. 4 ! Żeby anulować operację, przyciśnij przycisk #/:OFF.
Edycja nagranego minidysku (ciąg dalszy) Funkcje zaawansowane - Edycja nagranego minidysku - # Przenoszenie utworu 1 Rozpocznij odtwarzanie utworu, który ma zostać przeniesiony, i przyciśnij przycisk PLAY/PAUSE. 2 Przyciśnij przycisk EDIT kilkakrotnie, żeby wybrać funkcję „MOVE”. 3 Przyciśnij przycisk ENTER/SYNC. ! Żeby anulować operację, przyciśnij przycisk #/:OFF. 4 Przy pomocy przycisku ! lub " wybierz nowe położenie utworu. 5 Ponownie przyciśnij przycisk ENTER/SYNC.
Podłączenie do innego urządzenia audio # Podłączenie do urządzenia stereofonicznego # Podłączenie do radioodtwarzacza samochodowego Do gniazd LINE INPUT Uwaga: W modelu MD-MT88 należy dokonać podłączenia bezpośrednio do gniazda PHONES. Do gniazda REMOTE Do gniazda REMOTE Uwagi: ! Przy podłączeniu opisywanego odtwarzacza do urządzenia stereo zaleca się ustawienie poziomu głośności w napędzie na maksimum.
Inne funkcje oraz ostrzeżenia # Kontynuacja odtwarzania automatycznego # Akumulator Po zatrzymaniu odtwarzania i ponownym jego uruchomieniu bez wyjmowania minidysku odtwarzanie rozpoczyna się od miejsca, w którym zostało przerwane. ! Akumulator niklowo-metalowo-wodorkowy jest jedynym rodzajem Stop Pierwszy utwór ! ! Zatrzymany utwór Odtwarzanie Funkcje zaawansowane - Inne funkcje oraz ostrzeżenia - ! W wypadku wyjęcia minidysku ponowne odtwarzanie rozpoczyna się od pierwszego utworu.
Ograniczenia minidysków Podczas nagrywania lub edycji mogą wystąpić poniższe objawy. Nie oznaczają one uszkodzenia urządzenia. OBJAW OGRANICZENIA Na wyświetlaczu pojawia się komunikat „DISC Niezależnie od czasu trwania, nie można nagrać na dysku więcej niż 255 utworów. FULL” lub „TOC FULL”, mimo że pozostaje jeszcze Jeśli minidysk jest nagrywany lub edytowany powtórnie, albo kiedy ma zadrapania wolny czas nagrania.
Komunikaty o błędach KOMUNIKAT KOMUNIKAT ZNACZENIE BATT EMPTY ! Bateria jest rozładowana. BLANK MD ! Na dysku nie ma nagrania. DISC FULL ! Na dysku nie ma już miejsca na nagra- Er-MD** ! Mikroprocesor HOLD ! Włączona jest blokada przycisków. LOCKED ! Podczas nagrywania lub edycji próbo- nia (Zastąp dysk dyskiem nagranym.) Can’t COPY ! System SCMS uniemożliwia wykonanie kopii. Dodatek - Komunikaty o błędach - ! Podjęto próbę wykonania kopii danych innych niż muzyka.
KOMUNIKAT SORRY ZNACZENIE ! Urządzenie nie może spełnić wydanego polecenia, ponieważ aktualnie wyszukuje lub zmienia utwór. (Odczekaj chwilę i ponów próbę.) TEMP OVER ! Temperatura jest za wysoka. TOC FULL ! Nie ma już miejsca na zapisanie infor- macji tekstowych (tytuły utworów, tytuł dysku itd.). Tr.Protect ! Utwór jest chroniony przed zapisem. ?DISC ! Podjęto próbę odtworzenia dysku, zawierającego dane inne niż dźwięk. (Dysku zawierającego dane dźwięk nie można odtwarzać.
Rozwiązywanie problemów Wiele ewentualnych „problemów” może być rozwiązywanych przez użytkownika bez pomocy serwisu. PROBLEM Urządzenie nie włącza się Dodatek 45 - Rozwiązywanie problemów - W słuchawkach nie słychać żadnego dźwięku Urządzenie nie reaguje na wciskanie przycisków Podczas odtwarzania niektóre dźwięki są pomijane lub odtwarzanie zatrzymuje się w trakcie trwania utworu Nie można wyjąć minidysku. Nagranie i edycja są niemożliwe.
# Gdy pojawi się problem # Czyszczenie Jeśli opisywane urządzenie zostało poddane działaniu silnych bodźców zewnętrznych (wstrząsy mechaniczne, silne pole elektrostatyczne, nieodpowiednie napięcie zasilające będące skutkiem burzy, itp.), może się zdarzyć, że nie będzie działało prawidłowo. Jeśli urządzenie ulegnie zabrudzeniu, należy je przetrzeć miękką, suchą ściereczką. W wypadku silnego zabrudzenia należy użyć miękkiej ściereczki lekko zwilżonej wodą (tylko do obudowy).
Dane techniczne Dodatek 47 - Dane techniczne - Stawiając sobie za cel ciągłe doskonalenie swoich produktów firma SHARP zastrzega sobie prawo do wprowadzania zmian w parametrach konstrukcyjnych i danych technicznych urządzenia bez powiadamiania nabywcy. Dane dotyczące wydajności poszczególnych elementów są wartościami nominalnymi produkowanych jednostek. W pojedynczych przypadkach dopuszcza się odchylenia od podanych wielkości.
Wydajność źródeł zasilania Tryb 2 razy dłuższego nagrywania Tryb 4 razy dłuższego nagrywania Przy zastosowaniu dostarczonego z urządzeniem akumulatora* (całkowicie naładowanego) Nagrywanie ciągłe: ok. 7,5 godziny Odtwarzanie ciągłe: ok. 13 godzin Nagrywanie Odtwarzanie Nagrywanie Odtwarzanie ciągłe: ok. 10,5 ciągłe: ok. 15,5 ciągłe: ok. 13,5 ciągłe: ok. 17,5 godzin godziny godziny godzin Przy zastosowaniu dostępnej w sprzedaży baterii alkalicznej wielkości „AA” (LR6) Nagrywanie ciągłe: ok.
49 Notatki Notatki MD-MT88H/MD-MT99H
SHARP ELECTRONICS GESSELSCHAFT M.B.H. Sp. z o.o.