MX-M350U/MX-M450U/MX-M350N/MX-M450N 2006年12月13日 水曜日 午後3時1分 MODEL MX-M350U MX-M450U MX-M350N MX-M450N LASER PRINTER DIGITAL MULTIFUNCTIONAL SYSTEM MX-M350U/MX-M450U/MX-M350N/MX-M450N OPERATION MANUAL (for general information and copier operation) NA KS1 CZZ Copy_SEC.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 Each instruction also covers the optional units used with these products. The power switch positions are marked " I " to indicate power "ON" and " Caution: " to indicate stand-by. For complete electrical disconnection, pull out the main plug. The socket-outlet should be installed near the equipment and should be easily accessible. FOR YOUR RECORDS ...
Copy_SEC.book 2 ページ 2006年12月13日 水曜日 午後3時1分 Trademark acknowledgments The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and accessories. • Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows® Server 2003 and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries.
Copy_SEC.
Copy_SEC.
Copy_SEC.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 NOTES ● Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your nearest SHARP Service Department. ● This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest SHARP Service Department.
Copy_SEC.book 2 ページ 2006年12月13日 水曜日 午後3時1分 OPERATION MANUALS The following operation manuals are provided for the machine. Please read the appropriate manuals as needed for the features you wish to learn about. ● Operation manual (for general information and copier operation) (this manual): The first half of this manual provides general information about the machine, including safety information, loading paper, removing misfeeds, and regular maintenance.
00.fm 3 ページ 2006年12月19日 火曜日 午後10時20分 INSTALLATION REQUIREMENTS Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved. 1.The machine should be installed near an accessible power outlet for easy connection. 2.Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.
Copy_SEC.book 4 ページ 2006年12月13日 水曜日 午後3時1分 CAUTIONS 1.Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty prints. 2.The fusing unit is extremely hot. Exercise care in this area. 3.Do not look directly at the light source. Doing so may damage your eyes. Fusing unit 4.Five adjusters are provided on all optional stand/paper drawer units. These adjusters should be lowered until they contact the floor.
Copy_SEC.book 5 ページ 2006年12月13日 水曜日 午後3時1分 Laser Information Wave length Pulse times Output power 785 nm +10 nm -15 nm North America: 35 cpm model: (4.1 µs ± 4.1 ns)/7 mm 45 cpm model: (5.7 µs ± 5.7 ns)/7 mm Europe: 35 cpm model: (3.8 µs ± 3.8 ns)/7 mm 45 cpm model: (4.4 µs ± 4.4 ns)/7 mm 0.2 mW - 0.4 mW At the production line, the output power of the scanner unit is adjusted to 0.4 MILLIWATT PLUS 8 % and is maintained constant by the operation of the Automatic Power Control (APC).
00.fm 6 ページ 2006年12月13日 水曜日 午後5時11分 CONTENTS Page PRODUCT CONFIGURATIONS...................................0-1 OPERATION MANUALS ..............................................0-2 INSTALLATION REQUIREMENTS...............................0-3 CAUTIONS ...................................................................0-4 ● Laser Information..................................................0-5 CONTENTS..................................................................
Copy_SEC.book 7 ページ 2006年12月13日 水曜日 午後3時1分 CONTENTS CHAPTER 5 CONVENIENT COPY FUNCTIONS CHAPTER 8 SPECIFICATIONS SPECIAL MODES........................................................ 5-2 ● General procedure for using special functions ..... 5-2 ● Margin shift........................................................... 5-3 ● Erase .................................................................... 5-4 ● Dual page copy .................................................... 5-5 ● Pamphlet copy..............
Copy_SEC.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 CHAPTER 1 BEFORE USING THE PRODUCT This chapter contains basic information that should be read before using the product. Page INTRODUCTION..................................................................................... 1-2 MAIN FEATURES ................................................................................... 1-3 PART NAMES AND FUNCTIONS........................................................... 1-9 ● Exterior......................................
Copy_SEC.book 2 ページ 2006年12月13日 水曜日 午後3時1分 INTRODUCTION Thank you for purchasing a SHARP digital multifunction copier. Please read this manual before using the machine. In particular, be sure to read "INSTALLATION REQUIREMENTS" before using the machine. Please keep this manual close at hand for reference whenever necessary. This manual provides general information on using the machine, such as routine maintenance and how to load paper and remove misfeeds.
Copy_SEC.book 3 ページ 2006年12月13日 水曜日 午後3時1分 MAIN FEATURES The digital multifunction copier is capable of performing a variety of functions. This page shows features related to the copy function. ● Job programs See page 1-6 ● Sort mode See page 1-3 ● Group mode See page 1-3 ● Mirror Image See page 1-6 ● 2-sided Copy See page 1-3 ● B/W Reverse See page 1-6 (When the duplex module is installed.
Copy_SEC.book 4 ページ 2006年12月13日 水曜日 午後3時1分 MAIN FEATURES Reduction / Enlargement See page 4-15 Copies can be enlarged or reduced to the desired size. Erase See page 5-4 Shadows that appear around the edges of copies of books or thick originals can be erased. Original Original Copy Copy Edge erase Center erase Enlargement Reduction Edge+Center erase XY Zoom See page 4-18 Separate ratio settings can be selected for the length and width of a copy.
Copy_SEC.book 5 ページ 2006年12月13日 水曜日 午後3時1分 MAIN FEATURES Job Build See page 5-8 When you have a very large number of originals, the pages can be scanned in sets. Transparency Insert See page 5-23 Inserts can be automatically inserted between transparencies. Originals (1-sided) Copy 1 Originals (2-sided) 100 sheets 50 sheets Tandem Copy 50 sheets See page 5-10 Two machines can be used to run a large copy job in parallel.
Copy_SEC.book 6 ページ 2006年12月13日 水曜日 午後3時1分 MAIN FEATURES Card Shot See page 5-27 The front and back of a card can be copied onto one sheet of paper. This function is convenient for making copies for certification purposes and helps save paper. Original B/W Reverse White and black can be inverted on a copy to produce a negative image.
Copy_SEC.book 7 ページ 2006年12月13日 水曜日 午後3時1分 MAIN FEATURES Page numbering See page 5-35 Page numbers can be added to copies. Offset mode See page 3-8 Each set of output can be offset slightly from other sets for easy separation. Offset mode 1 Non-Offset mode *When the Finisher or Saddle stitch finisher is installed. Text See page 5-39 Entered text can be added to copies. Staple sort mode See page 3-8, 3-16 Sets of copies can be automatically stapled.
01.fm 8 ページ 2007年4月5日 木曜日 午後5時24分 MAIN FEATURES Hole punching See page 3-17 Copies can be punched to add holes. Original Document filing function See CHAPTER 7 A document image can be stored on the hard disk. A stored file can easily be called up and printed or transmitted.
01.fm 9 ページ 2006年12月13日 水曜日 午後5時16分 PART NAMES AND FUNCTIONS Exterior (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (12) 1 (11) (1) Bypass tray* (7) Operation panel (2) Exit tray* (8) Front cover (13) Open to add toner. (3) Automatic document feeder (See page 4-2.) This automatically feeds and scans multiple sheet originals. Both sides of two-sided originals can be scanned at once. (9) Power switch Press to turn power on and off.
01.fm 10 ページ 2006年12月13日 水曜日 午後5時18分 PART NAMES AND FUNCTIONS Interior (14) (15) (16) (18) (14) Duplex module side cover Open when a misfeed has occurred in the duplex module. (15) Side cover latch Push up to open the side cover when a misfeed has occurred in the main unit. (16) Fusing unit Lift up to open the side cover when a misfeed has occurred in the main unit. (17) (19) (17) Toner cartridge (drum/toner cartridge) The toner cartridge must be replaced when indicated on the operation panel.
01.fm 11 ページ 2006年12月13日 水曜日 午後4時2分 PART NAMES AND FUNCTIONS Part names and functions of peripheral devices (1) (2) (11) (10) 1 (3) (9) (4) (8) (5) (7) (6) (1) Upper exit tray extension (AR-TE4) Mount this unit to the upper paper exit tray. This extension is needed to support large size paper. (2) Finisher (AR-FN6) Output sheets can either be sorted in page order or grouped by page. Sorted sets or groups are offset stacked for easy separation when removed.
Copy_SEC.book 12 ページ 2006年12月13日 水曜日 午後3時1分 PART NAMES AND FUNCTIONS ■ Other optional equipment ●Network expansion kit (MX-NBX2) This is required to add on the network function. When this expansion kit is installed, the machine can be used as a network printer. ●Network expansion kit (MX-NBX3) Required to add the network function and a hard drive to the machine. Installing this expansion kit allows the machine to be used as a printer and enables use of the document filing function.
01.fm 13 ページ 2006年12月19日 火曜日 午後10時22分 PART NAMES AND FUNCTIONS Operation panel (1) PRINT When the document filing function has not been added. (2) (3) 1 PRINT READY DATA DOCUMENT FILING LINE DATA IMAGE SEND COPY SYSTEM JOB STATUS SETTINGS (4) (5) (1) Touch panel The machine status, messages and touch keys are displayed on the panel. The document filing*1, copy, network scanner*2, fax*3 , and Internet fax*4 functions are used by switching to the screen for the desired function.
Copy_SEC.book 14 ページ 2006年12月13日 水曜日 午後3時1分 PART NAMES AND FUNCTIONS Touch panel The touch panel screens shown in this manual are printed images, and may appear different from the actual screens. ■ Selecting a function [Example 1] PER. 0 ■ Using the touch panel OK [Example 1] CANCEL Items on the touch panel are easily selectable by 003 / 000 COPY touching the key 003 / 000 associated with the item Suzuki 010 / 000 with a finger.
Copy_SEC.book 15 ページ 2006年12月13日 水曜日 午後3時1分 PART NAMES AND FUNCTIONS ■ Job status screen (common to print, scan, fax and Internet fax) This screen is displayed when the [JOB STATUS] key on the operation panel is pressed. This screen can be used to display the "JOB QUEUE" (showing stored jobs and the current job) or the "COMPLETE" job list (showing finished jobs). This screen can be used to check jobs, interrupt a job in progress to perform another job, and cancel a job.
Copy_SEC.book 16 ページ 2006年12月13日 水曜日 午後3時1分 PART NAMES AND FUNCTIONS (3) [PRINT JOB] key This displays the print job list of print mode (copying, printing, fax reception, Internet fax reception, and self printing). (4) [SCAN TO] key This displays the transmission status and finished jobs of scan mode (Scan to e-mail, Scan to FTP, Scan to Desktop, and Scan to Network Folder) when the network scanner option is installed.
Copy_SEC.book 17 ページ 2006年12月13日 水曜日 午後3時1分 TURNING THE POWER ON AND OFF Use the power switch on the front of the machine to turn the power on or off. "ON" position "OFF" position Power switch CAUTION Before turning off the main power switch, make sure that the communication and data indicators are not blinking on the operation panel.
Copy_SEC.book 18 ページ 2006年12月13日 水曜日 午後3時1分 AUDITING MODE Auditing mode can be enabled to keep track of the number of pages printed and transmitted (scanned) by each account (up to 500 accounts can be established). The page counts can be viewed and totaled as needed.
02-1.fm 1 ページ 2006年12月13日 水曜日 午後4時3分 CHAPTER 2 MANAGING THE MACHINE This chapter explains how to load paper, replace the toner cartridge, and remove paper misfeeds. It also contains information about supplies. Page LOADING PAPER ................................................................................... 2-2 ● Loading paper in paper tray 1 ......................................................... 2-2 ● Changing the paper size in paper tray 1 .........................................
02-1.fm 2 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER If the paper runs out during printing, a message will appear in the display. Follow the procedure below to load paper. NOTES ● Do not use curled or folded paper. Doing so may cause a misfeed. ● For best results use paper supplied by SHARP. (See page 2-4.) ● When you change the paper type and size in paper tray 1, set the paper type and size referring to "Setting the paper type and paper size" (page 2-5).
02-1.fm 3 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER Specifications of paper trays The specifications for types and sizes of paper that can be used in each tray are shown below. Tray Tray No. (tray name) Applicable paper types Applicable paper sizes Paper weight Paper tray 1 Tray 1 Plain paper (Refer to the next page ● 8-1/2" x 11", A4, B5 for applicable plain papers.
02-1.fm 4 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER ■ Applicable plain paper For satisfactory results, plain paper must conform to the following requirements. Paper in AB system Paper in inch system A5 to A3 Plain paper 5-1/2" x 8-1/2" to 11"x17" 16 to 28 lbs. or 60 to 105 g/m 2 Recycled, colored, pre-punched, pre-printed and letterhead papers must conform to the same conditions as above. ■ Applicable special paper For satisfactory results, special paper must conform to the following requirements.
02-1.fm 5 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER Setting the paper type and paper size Follow these steps to change the paper type setting if the paper type is changed in either paper tray. For the paper types that can be used in each tray, see page 2-3. 1 Press the [SYSTEM SETTINGS] key. The system setting menu screen will appear. PY SYSTEM JOB STATUS SETTINGS 5 Touch the [TYPE / SIZE] key. PER TRAY SETTINGS TYPE / SIZE TRAY 2 PRINT 2 Touch the [PAPER TRAY SETTINGS] key.
02-1.fm 6 ページ 2006年12月19日 火曜日 午後10時24分 LOADING PAPER the size of paper that was loaded in 7 Select the tray. the 8 Touch screen. Touch the appropriate keys (checkboxes). [OK] key in the size setting You will return to the tray setting screen of step 4. SYSTEM SETTINGS TYPE TRAY 2 TYPE/SIZE SETTING output functions that can be used 9 Select with the selected tray.
02-1.fm 7 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER Programming and editing paper types To program or edit the name of a paper type or set paper attributes, follow the steps below. steps 1 and 2 of "Setting the paper 1 Follow type and paper size" (page 2-5) the [PAPER TYPE REGISTRATION] 2 Touch key. "FIXED PAPER SIDE" : Select when paper is to be loaded print side down in the tray. Make sure a checkmark does not appear when paper is to be loaded print side up.
02-1.fm 8 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER Loading paper in the multi purpose drawer The method of loading paper into the multipurpose drawer is the same as for paper tray 1 described on page 2-2. For specifications of paper, see page 2-3. When loading envelopes, postcards or transparency film, follow the descriptions below. ● Two maximum height lines are indicated: one for plain paper and one for special paper.
02-1.fm 9 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER Printing onto envelopes ● Do not use envelopes that have metal clasps, plastic snaps, string closures, windows, linings, self-adhesive patches or synthetic materials. Attempting to print on these may cause misfeeds, inadequate toner adherence or other trouble. ● Creases or smudging may occur. This is especially true of embossed surfaces and other irregular surfaces.
02-1.fm 10 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER ■ Loading transparency film Be sure to load the transparency film with the white label side up. Make sure no image will be printed on the label. Printing on the label may cause smudges on prints. Transparency film must be set in the portrait orientation. Specifications (multi purpose drawer) Name Multi purpose drawer Paper size/weight See specifications of paper trays on page 2-3. Paper capacity 500 sheets (20 lbs.
02-1.fm 11 ページ 2006年12月13日 水曜日 午後4時3分 LOADING PAPER Loading paper in the stand/MPD & 2000 sheet paper drawer Upper paper tray: The upper paper tray is equivalent to the multi purpose drawer. The method of loading paper and the paper that can be used are the same as for the multi purpose drawer. Refer to the description of the multi purpose drawer (see page 2-8). Lower paper tray: The lower paper tray is a large capacity tray that holds 2,000 sheets of 8-1/2" x 11" or A4 paper (20 lbs. (80 g/m2)).
Copy_SEC.book 12 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS The system settings can be used as needed to meet the needs of your workplace. The items that can be set with the system settings are shown below. ● Total count . . . . . . . . . . . . . . . . . . The number of pages processed by the machine and optional equipment can be displayed. (See page 2-14) ● Default settings . . . . . . . . . . . . . . Used to configure the screen contrast, date and time, and keyboard selection*1 settings.
Copy_SEC.book 13 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS 5 Touch the [DATE FORMAT] key. The following screen appears. SYSTEM SETTINGS OK DATE FORMAT 2010/04/04/SUN 11:30 More information on setting procedures In the following type of screen, a setting is selected by touching the key so that a checkmark ( ) appears. The settings below are configured to allow use of tray 1 in print, copy, and fax modes. To display the next screen, touch the or keys.
Copy_SEC.book 14 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS About the settings ■ Total count ■ List print This displays the following sheet counts (the counts that can be displayed vary depending on the options installed): This is used to print lists of machine settings and a test page to check resident fonts. The following lists and pages are available: (1) Number of pages output by the machine. (2) Number of original pages transmitted by the machine.
Copy_SEC.book 15 ページ 2006年12月13日 水曜日 午後3時1分 REPLACING THE TONER CARTRIDGE When toner runs low, a message will appear to inform you that the toner cartridge must be replaced. NOTE To view the approximate amount of toner remaining, hold down the [COPY] key during printing or when the machine is on standby. The percentage of toner remaining will appear in the display while you hold down the key. When the percentage falls to "25-0%" , obtain a new toner cartridge and keep it ready for replacement.
Copy_SEC.book 16 ページ 2006年12月13日 水曜日 午後3時1分 STORAGE OF SUPPLIES Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of Sharp products. Look for the Genuine Supplies label on the toner package. GENUINE SUPPLIES ■ Proper storage 1.
Copy_SEC.book 17 ページ 2006年12月13日 水曜日 午後3時1分 MISFEED REMOVAL When a misfeed has occurred during printing, the message "A MISFEED HAS OCCURRED". will appear in the touch panel display of the operation panel and printing including copying and facsimile output will stop. The approximate misfeed locations are indicated with " " shown in the illustration below. The page numbers for detailed information on misfeed removal are also shown.
02-2.fm 18 ページ 2006年12月13日 水曜日 午後5時33分 MISFEED REMOVAL Misfeed in the transport area, fusing area, and exit area o CAUTION The fusing unit is hot. Take care in removing paper. (Do not touch the metal parts.) the duplex module and slide it to 1 Unlatch the left. Unlatch the module and gently move the module away from the machine. If the machine is not equipped with a duplex module, open the side cover similarly. Roller rotating knob B CAUTION The fusing unit is hot. Take care in removing paper.
Copy_SEC.book 19 ページ 2006年12月13日 水曜日 午後3時1分 MISFEED REMOVAL Misfeed in the duplex module the duplex module and slide it to 1 Unlatch the left. Unlatch the unit and gently move the module away from the machine. duplex module has an exit tray, rotate 2 Ifit the up out of the way and open the cover of the duplex module. If no exit tray is attached, just open the cover of the duplex module and ignore any reference to the tray in the following steps. 5 Gently close the duplex module.
Copy_SEC.book 20 ページ 2006年12月13日 水曜日 午後3時1分 MISFEED REMOVAL Misfeed in the paper feed area NOTE Be sure to follow the misfeed removal sequence. Do not pull the tray out immediately as the misfeed may have occurred with paper partially fed out of the tray. Open the left cover and see if there is misfed paper first (steps 1 and 2). If you open the tray without checking, the partially fed paper may tear and leave torn pieces in the machine, increasing the difficulty of removal.
Copy_SEC.book 21 ページ 2006年12月13日 水曜日 午後3時1分 MISFEED REMOVAL ■ Misfeed in the multi purpose drawer Unlatch the duplex module and slide it to the left. 1 Unlatch the module and gently move the module away from the machine. If the machine is not equipped with a duplex module, open the side cover similarly. the 2 Open drawer. left cover of the stand/paper Hold the knob and gently open the cover. If the machine is not equipped with a stand/ paper drawer, open the left cover of the multi purpose drawer.
Copy_SEC.book 22 ページ 2006年12月13日 水曜日 午後3時1分 REMOVING AN ORIGINAL MISFEED Removing a misfed original from the automatic document feeder If an original misfeed occurs in the automatic document feeder, follow the steps below to remove the misfed original. NOTES ● For misfeed removal in the main unit and other peripheral devices, see page 2-17 ● When a misfeed occurs, touch the [INFORMATION] key to display detailed information for misfeed removal.
Copy_SEC.book 23 ページ 2006年12月13日 水曜日 午後3時1分 TROUBLESHOOTING Check the following troubleshooting list before requesting service as many problems can be fixed by the user. If you are unable to solve the problem by checking the list, turn off the power switch, unplug the power cord. Problems related to general use of the machine are described below. For problems related to the copy function, see page 6-3. For problems related to document filing, see page 7-31.
Copy_SEC.book 24 ページ 2006年12月13日 水曜日 午後3時1分 TROUBLESHOOTING Problem Printing stops before the job is finished. Check Solution or cause If too many pages collect on the output tray, the tray full sensor activates and Remove the paper from the output tray. stops printing. The paper tray is out of paper. Load paper. (Page 2-2) Smudges on printed sheets. Does a message appear indicating the need for maintenance? Please contact your dealer as soon as possible.
Copy_SEC.book 25 ページ 2006年12月13日 水曜日 午後3時1分 TROUBLESHOOTING Problem Printed paper is wrinkled or the image rubs off easily. The contrast on the touch panel is too high or too low. Printing takes place on the wrong side of the paper. Marks appear at regular intervals on printed pages. Check Solution or cause Is paper other than SHARPrecommended paper being used? Use SHARP-recommended paper. (Page 2-16) Is the paper size or weight outside the specifications? Use paper within the specifications.
Copy_SEC.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 CHAPTER 3 PERIPHERAL DEVICES This chapter describes operating instructions for the Mail-Bin Stacker, the Finisher, the Saddle Stitch Finisher, and the Duplex Module, as well as Sharp OSA (application communication module and external account module). Page DUPLEX MODULE ................................................................................. 3-2 ● Part names......................................................................................
Copy_SEC.book 2 ページ 2006年12月13日 水曜日 午後3時1分 DUPLEX MODULE If a duplex module is installed, printing onto both sides of paper can be performed. Two types of duplex modules are available: duplex module/bypass tray and duplex module. The descriptions in this manual are for the duplex module/bypass tray. For information on misfeed removal for these modules, see page 2-19. Part names Exit tray The tray is extendable to support large size paper.
03.fm 3 ページ 2006年12月13日 水曜日 午後5時36分 DUPLEX MODULE Loading paper in the bypass tray The bypass tray can be used for plain paper and special paper including labels. Up to 100 sheets of standard paper can be set. For paper types that can be used in the bypass tray, refer to page 2-3. NOTE If the paper type or size is changed, be sure to enter the paper type and size as in step 4. 1 Open the bypass tray.
Copy_SEC.book 4 ページ 2006年12月13日 水曜日 午後3時1分 DUPLEX MODULE Troubleshooting (concerning the duplex module) Check the list below before calling for service. Problem The machine will not print duplex prints. Printed images onto paper from the bypass tray are skewed. A paper misfeed occurs in the bypass tray. When printing on a special size of paper, part of the printed image is missing.
Copy_SEC.book 5 ページ 2006年12月13日 水曜日 午後3時1分 MAIL-BIN STACKER The mail-bin stacker has 7 mail bins which can each be designated to receive printed output from a user or a group of users . Output paper in the copy mode and the fax mode will be delivered to the top tray of the stacker separated from printed output. (Printed output can also be delivered to the top tray.) Part names Top cover Open for misfeed removal. Front cover Open for misfeed removal.
Copy_SEC.book 6 ページ 2006年12月13日 水曜日 午後3時1分 MAIL-BIN STACKER Misfeed in the mail-bin stacker If a misfeed has occurred in the mail-bin stacker during printing, remove the misfed paper following the procedure below. 1 Open the top cover. Top cover 6 Remove the misfed paper. Move the tab in the direction of the arrow as shown in the illustration to open the top cover. 2 Remove the misfed paper. 7 Close the paper guide. Be careful not to tear the misfed paper during removal.
Copy_SEC.book 7 ページ 2006年12月13日 水曜日 午後3時1分 FINISHER The finisher can deliver collated sets either stapled or unstapled. Unstapled sets can be offset stacked from the previous set for easy separation of the sets. Part names Latch Top tray Printer, copier and fax output can be delivered here. To print onto large paper (11" x 17", 8-1/2" x 14", 8-1/2" x 13", A3 or B4), extend the tray. Release the latch to open the finisher for misfeed removal. Top cover Open for removal.
Copy_SEC.book 8 ページ 2006年12月13日 水曜日 午後3時1分 FINISHER Finisher functions ■ Group mode ■ Sort mode Sorted sets will be delivered. Original Groups of prints or copies of the same page will be delivered. Printouts Printouts Original ■ Offset mode Offset mode Non-offset mode Sets will move from side to side so that each set or group will be offset from the previous set or group for easy separation. The offset function can only be used in the offset tray. Stapled sets will not be offset.
Copy_SEC.book 9 ページ 2006年12月13日 水曜日 午後3時1分 FINISHER Using the finisher functions When the [OUTPUT] key on the main screen of copy mode is touched, a screen for selecting the sort/group/staple sort functions and selecting an exit tray will appear. As a selection is made, the touch key for the selection will be highlighted. OUTPUT OK SORT (8) TOP TRAY (7) STAPLE SORT OFFSET TRAY (6) GROUP OFFSET (1) (2) (3) (1) [GROUP] key (See page 3-8.
Copy_SEC.book 10 ページ 2006年12月13日 水曜日 午後3時1分 FINISHER Staple cartridge replacement When the staple cartridge becomes empty, the message "Add staples." will appear in the message display of the operation panel. Follow the procedure below to replace the staple cartridge. 1 Open the front cover. NOTES ● Do not remove the tape from the cartridge before inserting the staple cartridge into the box. ● When reinstalling the staple box, push it in until it clicks into place.
Copy_SEC.book 11 ページ 2006年12月13日 水曜日 午後3時1分 FINISHER ■ Checking the staple unit If the message "CHECK THE STAPLER UNIT" or "CHECK STAPLER POSITION OR STAPLER JAM" appears, follow the procedure below. 1 Open the finisher compiler. Release the latch to open the finisher compiler. the misfed paper from the stapler 2 Remove compiler. Be careful not to tear the misfed paper during removal. 3 Close the finisher compiler. 7 Raise the lever at the end of the staple box. Remove the top staple if it is bent.
Copy_SEC.book 12 ページ 2006年12月13日 水曜日 午後3時1分 FINISHER Misfeed in the finisher When a misfeed occurs in the finisher, remove the misfed paper following the procedure below. the misfed paper from the output 1 Remove area. the paper 5 Raise misfed paper. Be careful not to tear the misfed paper during removal. guide and remove the Be careful not to tear the misfed paper during removal. Paper guide 2 Open the finisher top cover.
Copy_SEC.book 13 ページ 2006年12月13日 水曜日 午後3時1分 FINISHER Troubleshooting finisher problems Check the list below before calling for service. Problem Check Solution or cause Are any finisher covers open? The finisher does not operate. Close all covers. Open the finisher as described in Message indicating need to remove step 4 on page paper from the stapler compiler 3-12 and remove all paper from the displayed? stapler compiler.
Copy_SEC.book 14 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER The saddle stitch finisher can automatically place two staples for centerline binding of prints or copies and fold them along the centerline. An optional hole punching unit is available for installation into the finisher. Part names Stapler compiler Paper to be stapled is stacked temporarily. Top cover Open for misfeed removal.
Copy_SEC.book 15 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER Stapling capacity 8-1/2" x 11" or A4 or smaller size: 50 sheets*(20 lbs. or 80 g/m2) 8-1/2" x 14" or B4 or larger size: 25 sheets*(20 lbs. or 80 g/m2) *Up to two sheets of 34 lbs. or 128 g/m2 paper can be included as covers. Staples Upper tray: Single staple can be placed in the top left or lower left corners or two staples can be centered on the left side.
03.fm 16 ページ 2006年12月19日 火曜日 午後10時25分 SADDLE STITCH FINISHER ■ Staple sort mode Collated sets of prints or copies will be stapled and delivered to the offset tray. When saddle stitching is selected, the prints or copies will be stapled at the center and delivered to the saddle stitch tray. The stapling positions, orientation, paper size for stapling, and stapling capacity are shown below.
Copy_SEC.book 17 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER ■ Saddle stitch function The saddle stitch finisher can automatically place two staples for centerline binding of prints or copies and fold them along the centerline. 6 4 2 ■ Hole punching (only if a punch module is installed) If the saddle stitch finisher is equipped with a hole punch module, printed paper can be hole punched and delivered to the offset tray. Saddle stitching and hole punching cannot be selected at the same time.
Copy_SEC.book 18 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER Using the saddle stitch finisher When [OUTPUT] is selected on the main screen of copy mode, a screen for making selections for sort, group, staple sort, saddle stitch, punch and exit tray will appear. (1)(2)(3) (4)(5) (6) (7) OUTPUT OK OFFSET TRAY SORT CENTER TRAY STAPLE SORT GROUP SADDLE STITCH PUNCH (9) (10) OFFSET (8) (1) [GROUP] key (See page 3-15.
Copy_SEC.book 19 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER Staple cartridge replacement and staple jam removal When the staple cartridge becomes empty or staples become jammed, a message will appear in the message display of the operation panel. Follow the procedure below to replace the staple cartridge or remove jammed staples. ■ Staple cartridge replacement 1 Open the front cover. a new 6 Insert staple box.
Copy_SEC.book 20 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER ■ Staple jam removal the saddle stitch finisher and slide 1 Unlatch it away from the machine. saddle stitch was selected, open the 5 Ifsaddle stitch section cover. 2 Open the front cover. 6 Remove the misfed paper. Be careful not to tear the misfed paper during removal. roller rotating knob C as shown in the 3 Turn illustration until the blue indication is 7 Close the saddle stitch section cover. seen.
Copy_SEC.book 21 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER roller rotating knob A in the direction 9 Turn of the arrow to move the staple unit to the 12 Return the lever to its original position. front. Turn the roller rotating knob until the triangle mark is aligned with the index. Roller rotating knob A Staple unit 13 Reinstall the staple box. 10 Remove the staple box. Push the staple box in until it clicks into place. 3 11 Raise the lever at the end of the staple box.
Copy_SEC.book 22 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER Misfeed in the saddle stitch finisher When a misfeed occurs in the saddle stitch finisher, remove the misfed paper following the procedure below. the detach button and separate the 1 Press saddle stitch finisher from the machine. 5 Remove the misfed paper. Remove the paper gently, taking care not to tear it. CAUTION The saddle stitch finisher and the machine are connected at the rear. Exercise caution when pulling them apart.
Copy_SEC.book 23 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER 10 Open the front cover. the saddle stitch finisher back onto the 15 Push machine. roller rotating knob D in the direction of 11 Rotate the arrow. Roller rotating knob D 3 any misfed paper from the saddle 12 Remove stitch tray. Remove the paper gently, taking care not to tear it. 13 Close the cover of the saddle stitch section. 14 Close the front cover.
Copy_SEC.book 24 ページ 2006年12月13日 水曜日 午後3時1分 SADDLE STITCH FINISHER Troubleshooting (concerning the saddle stitch finisher) Check the list below before calling for service. Problem Check The saddle stitch finisher does not operate. Are any saddle stitch finisher covers open? Close all covers. (See page 3-14.) Message indicating need to remove paper from the stapler compiler displayed? Remove all remaining paper from the stapler compiler referring to step 4 on page 3-20.
Copy_SEC.book 25 ページ 2006年12月13日 水曜日 午後3時1分 SHARP OSA Sharp OSA (Open Systems Architecture) is an architecture that enables external applications to be directly connected to a digital multifunction machine over a network. When a digital multifunction machine that supports Sharp OSA is used, the operation panel controls and functions of the machine such as scan send can be linked to an external application.
Copy_SEC.book 26 ページ 2006年12月13日 水曜日 午後3時1分 APPLICATION COMMUNICATION MODULE (MX-AMX2) ■ Selecting the standard application from document filing mode The [Sharp OSA] key appears in the upper right-hand corner of the document filing screen. Follow the steps below to select a standard application. 1 Touch the [Sharp OSA] key. Sharp OSA FILE RETRIEVE FILE FOLER If no standard applications have been stored in the Web pages, the key cannot be touched. QUICK FILE FOLDER 2 Select the standard application.
Copy_SEC.book 27 ページ 2006年12月13日 水曜日 午後3時1分 EXTERNAL ACCOUNT MODULE (MX-AMX3) The external account module is required to use a "external account application" on the machine. An external account application can be used in "external authentication mode" or "external count mode". When external authentication mode is used, the login screen is retrieved from the application when the machine is started.
Copy_SEC.
Copy_SEC.
Copy_SEC.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 CHAPTER 4 MAKING COPIES This chapter explains the basic procedures for making copies, including selection of the copy ratio and other copy settings. Page AUTOMATIC DOCUMENT FEEDER ...................................................... 4-2 ● Acceptable originals ........................................................................ 4-2 PLACING ORIGINALS............................................................................
Copy_SEC.book 2 ページ 2006年12月13日 水曜日 午後3時1分 AUTOMATIC DOCUMENT FEEDER The automatic document feeder automatically feeds originals into the machine, making continuous copying possible. In addition, both sides of two-sided sheet originals can be simultaneously scanned. This function is convenient when you have a large number of original pages to scan.
04.fm 3 ページ 2006年12月13日 水曜日 午後5時43分 PLACING ORIGINALS ■ Using the feeder automatic document ■ Using the document glass the document cover, make sure that 1 Open an original has not been left on the Open the document cover, place the original face down on the document glass, and then gently close the document cover. document glass, and then gently close the document cover. Original size detector NOTES ● After placing the original, be sure to close the document cover.
Copy_SEC.book 4 ページ 2006年12月13日 水曜日 午後3時1分 PLACING ORIGINALS ■ Standard original placement orientations [Example 1] Document feeder tray Document glass Top Top Bottom Bottom [Example 2] Top Bottom Place originals in the document feeder tray or on the document glass so that the top and bottom of the original is positioned as shown in the illustration. If not, staples will be incorrectly positioned and some special features may not give the expected result.
Copy_SEC.book 5 ページ 2006年12月13日 水曜日 午後3時1分 CHECKING THE SIZE OF A PLACED ORIGINAL If the placed original is a standard size, the size will be automatically detected (automatic original detection function) and displayed in the touch panel. Make sure that the correct size has been detected. (A) : The original size is displayed. (B) : [AUTO] appears when the automatic original detection function is operating.
Copy_SEC.book 6 ページ 2006年12月13日 水曜日 午後3時1分 STORING, DELETING, AND USING ORIGINAL SIZES Up to 9 special original sizes can be stored. Stored sizes can be easily called up and are not erased if the power is turned off. Storing a frequently used original size saves you the trouble of manually setting the size each time you copy that size of document. ● To cancel an original size storing, using, or deleting operation, touch the [ORIGINAL] key on the screen.
Copy_SEC.book 7 ページ 2006年12月13日 水曜日 午後3時1分 NORMAL COPYING This section describes the normal copying procedure. Making copies with the automatic document feeder ■ 1-sided copies of 1-sided originals Original Copy the originals in the document feeder 1 Place tray. (pages 4-3 to 4-6) 5 Touch the [OK] key. 0 OK 4 2 Make sure that the 1-sided to 1-sided copy mode is selected.
Copy_SEC.book 8 ページ 2006年12月13日 水曜日 午後3時1分 NORMAL COPYING 7 Select the desired output mode (page 4-9). The sort mode is the default mode. To select the group OUTPUT mode, touch the [OUTPUT] key, then touch the [GROUP] key FILE on the output setting screen, and then touch the [OK] key on the setting screen. 2-SIDED COPY the numeric keys to set the desired 8 Use number of copies. Up to 999 can be set. If you are only making a single copy, the copy can be made with the copy number display showing "0".
Copy_SEC.book 9 ページ 2006年12月13日 水曜日 午後3時1分 NORMAL COPYING ■ Copy output (sort and group) Example: Making five sets or five copies each of three originals ● Sorting copies into sets Original Five sets of copies OUTPUT SORT SPECIAL MODES 2-SIDED COPY OUTPUT GROUP LOGOUT Set the number of copies (5) Touch the [OUTPUT] key Touch the [SORT] key Press the [START] key When using the automatic document feeder, sorting is automatically selected when the original is placed in the document feeder.
Copy_SEC.book 10 ページ 2006年12月13日 水曜日 午後3時1分 NORMAL COPYING Automatic two-sided document feeder copying using the automatic When the optional duplex module is installed, the following automatic two-sided copying can be performed. The paper is automatically turned over during copying, allowing two-sided copies to be made with ease. Original Copy 1. Automatic two-sided copying from one-sided originals 2. Automatic two-sided copying from two-sided originals 3.
04.fm 11 ページ 2006年12月13日 水曜日 午後5時43分 NORMAL COPYING Copying from the document glass When copying originals which cannot be fed from the automatic document feeder such as thick originals, open the document cover and copy the originals from the document glass. ■ 1-sided copies of 1-sided originals Original Copy the original on the document glass. 1 Place (pages 4-3 to 4-6) that paper of the same size as the 3 Ensure original is automatically selected*.
Copy_SEC.book 12 ページ 2006年12月13日 水曜日 午後3時1分 NORMAL COPYING the desired output mode. (page 44 Select 9.) 2-SIDED COPY OUTPUT FILE Group mode default mode. is 6 Press the [START] key. Replace the original with the next original and press the [START] key. Repeat this operation until all originals have been scanned. the To select sort mode, touch the [OUTPUT] key, touch the [SORT] key in the screen that appears, and then touch the [OK] key. the numeric keys to set the desired 5 Use number of copies.
04.fm 13 ページ 2006年12月13日 水曜日 午後5時44分 NORMAL COPYING Automatic two-sided copying from the document glass When the optional duplex module is installed, the following automatic two-sided copying can be performed. The paper is automatically turned over during copying, allowing two-sided copies to be made with ease. Original Copy the original on the document glass.
Copy_SEC.book 14 ページ 2006年12月13日 水曜日 午後3時1分 ADJUSTING THE EXPOSURE Select an appropriate exposure mode for the original to be copied. The selections are AUTO, TEXT, TEXT/PHOTO and PHOTO. ■ Automatic exposure adjustment AUTO The default exposure ORIGINAL setting is "AUTO", which automatically adjusts the exposure for the original. To select the exposure mode, or to 1 AUTO 8 /2 x11 manually adjust the PAPER SELECT exposure level, follow the steps below.
Copy_SEC.book 15 ページ 2006年12月13日 水曜日 午後3時1分 REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected automatically or manually. ● Automatic selection: Auto image (see below) ● Manual selection: Preset copy ratios/zoom (see page 4-16) Automatic selection (auto image) The reduction or enlargement ratio will be selected automatically based on the original size and the selected paper size. the original in the document feeder 1 Place tray or on the document glass.
Copy_SEC.book 16 ページ 2006年12月13日 水曜日 午後3時1分 REDUCTION/ENLARGEMENT/ZOOM Manual selection (preset copy ratios/zoom) Preset ratios (maximum 400%, minimum 25%) can be selected with the enlargement and reduction keys. In addition, the zoom keys can be used to select any ratio from 25% to 400% in increments of 1%.
Copy_SEC.book 17 ページ 2006年12月13日 水曜日 午後3時1分 REDUCTION/ENLARGEMENT/ZOOM sure that an appropriate paper size 6 Make has been selected based on the selected ratio. ORIGINAL AUTO EXPOSURE AUTO 81/2x11 PAPER SELECT Auto paper select display 64% COPY RATIO NOTE If the auto paper select display does not appear, a tray with the correct size of paper for the selected ratio will not be automatically selected. the numeric keys to set the desired 7 Use number of copies. Up to 999 can be set.
Copy_SEC.book 18 ページ 2006年12月13日 水曜日 午後3時1分 REDUCTION/ENLARGEMENT/ZOOM XY ZOOM The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed separately. The ratios can be set from 25% to 400% in increments of 1%. Example: Selecting 100% for the length and 50% for the width Copy Original the original in the document feeder 1 Place tray or on the document glass. (pages 4-3 to 4-6) NOTE When the original is placed in the document feeder, the ratio can be set from 25% to 200%.
04.fm 19 ページ 2006年12月19日 火曜日 午後10時26分 REDUCTION/ENLARGEMENT/ZOOM the 7 Use ZOOM ([ reduction, enlargement, and ], [ ]) keys to change the copy ratio in the vertical (Y) direction. 77% X 50 70 Y 64% any desired copy settings such as 10 Select the exposure or number of copies, and then press the [START] key. A fixed ratio key will not become highlighted when touched. ZOOM 50% 50 77 Y The zoom keys can be used to change the ratio from 25% to 400% in increments of 1%.
Copy_SEC.book 20 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL PAPERS The tray 2 and the bypass tray on the optional duplex module with bypass tray can be used to make copies on transparencies, postcards, label sheets, envelopes*1, and plain paper. *1 Envelopes can be placed in the tray 2. the original in the document feeder 1 Place tray or on the document glass. (pages 4-3 5 Select the bypass tray.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 CHAPTER 5 CONVENIENT COPY FUNCTIONS This chapter explains special-purpose functions, storing of copy settings, and other convenient functions. Please select and read sections of this chapter as needed. Page SPECIAL MODES................................................................................... 5-2 ● General procedure for using special functions ................................ 5-2 ● Margin shift...........................................................
Copy_SEC.book 2 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Touch the [SPECIAL MODES] key in the main screen of copy mode to open the special modes screen. The following functions can be selected in the special modes screen. Touch the [SPECIAL MODES] key in the main screen. (1) (2) (3) READY TO SCAN FOR COPY.
Copy_SEC.book 3 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Margin shift The margin shift function will automatically shift the text or image on the copy paper approximately 1/2" (10 mm) in its initial setting. This function is convenient when stapling or binding copies with a string. NOTES ● The initial setting for the margin width can be changed in the administrator settings to any value from 0 to 1" (0 to 20 mm).
Copy_SEC.book 4 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Erase The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The erase modes that can be selected are shown below. The erase width is approximately 1/2" (10 mm) in it's initial setting. NOTE The initial setting for the erasure width can be changed in the administrator settings to any value from 0 to 1" (0 to 20 mm).
Copy_SEC.book 5 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Dual page copy The dual page copy function produces separate copies of two documents placed side by side on the document glass. This function is especially useful when copying books and other bound documents. [Example] Copying right and left pages of a book Book original Dual page copy ●The dual page copy function can be used only when copying from the document glass. The automatic document feeder cannot be used with this function.
Copy_SEC.book 6 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Pamphlet copy The pamphlet copy function is used to arrange copies in proper order for eventual center-stapling and folding into a booklet. Two original pages are copied onto each side of copy paper. Four pages are, therefore, copied onto one sheet. This function is convenient for arranging copies into an attractive booklet or pamphlet. NOTE To make pamphlet copies of a book or other bound original, use the book copy function (page 5-26).
Copy_SEC.book 7 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES whether or not you wish to copy on 5 Select the cover ("YES" or "NO"). the original in the document feeder 9 Place or on the document glass. (page 4-3) PRINT ON COVER YES that the desired paper size has 10 Ensure been automatically selected based on the NO original size. AUTO EXPOSURE 6 Select the paper tray for the cover. CANCEL OK PAPER TRAY (1) TRAY2 (2) 81/2x11 PLAIN (1)The currently selected paper tray for the cover is displayed.
Copy_SEC.book 8 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Job build Use job build mode when you need to copy more originals than can be placed in the document feeder at once. The maximum number of originals that can be placed in the document feeder at once is 50 sheets (30 sheets when the size is B4 or larger; for more information see "Acceptable originals" on page 4-2). This function lets you divide and scan the originals in sets. This function allows the original pages to be scanned in sets.
Copy_SEC.book 9 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Changing the copy settings for each set of originals When using job build mode, you can change the copy settings each time you place a set of originals. After performing step 4 on page 5-8, follow the steps below. 5 Touch the [CHANGE] key. 7 Touch the [READ-END] key. INTERRUPT ES ORIGINAL INTERRUPT ES 81/2x11 PLACE NEXT ORIGINAL. PRESS [START]. TO CHANGE COPY SETTINGS, PRESS [CHANGE]. CHANGE 4. ORIGINAL 81/2x11 PLACE NEXT ORIGINAL.
Copy_SEC.book 10 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Tandem copy This function can only be used on the MX-M350N/MX-M450N, or when the network function has been added. Two machines connected to the same network can be used to run a large copy job in parallel. By dividing the job in half, approximately half the time is required to complete the job. To use this function, two machines must be connected to your network as network printers.
Copy_SEC.book 11 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES 5 Press the [START] key. NOTES ● To perform tandem copying, the server machine and client machine must meet certain conditions. After the [START] key is pressed on the server machine, the server machine verifies that the conditions have been met. If the conditions have not been met, tandem copying does not begin and "TANDEM OUTPUT IS NOT ALLOWED. OUTPUT ALL SETS USING MASTER MACHINE?" appears in the display.
Copy_SEC.book 12 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Covers/inserts A different type of paper can be inserted in positions corresponding to front and back covers of a copy job when the automatic document feeder is used. A different type of paper can also be automatically added as an insert at specified pages. ● Covers/inserts can be disabled in the administrator settings (page 11 of the administrator settings guide).
Copy_SEC.book 13 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Procedure for inserting front and back cover paper The paper for the front cover is called the front cover paper ("FRONT COVER" in the touch panel). The paper for the back cover is called the back cover paper ("BACK COVER" in the touch panel). ●Examples of insertion methods for the front and back cover paper are given on pages 5-18 to 5-21. To display the special modes screen... See "General procedure for using special functions" on page 5-2.
Copy_SEC.book 14 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Procedure for adding inserts You can have different paper automatically inserted as an insert at a specified pages. Two types of insert paper can be used. These are specified with the [INSERTION TYPE A SETTING] key and [INSERTION TYPE B SETTING] in the touch panel. ●Examples of insertion methods for insert paper are given on page 5-22. To display the special modes screen... See "General procedure for using special functions" on page 5-2.
Copy_SEC.book 15 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES the [INSERTION SETTINGS] key to 8 Touch specify the pages where you wish to insert wish to insert a different paper with 11 Iftheyou[INSERTION TYPE B SETTING] key, the insert papers of [INSERTION TYPE A SETTING] and [INSERTION TYPE B SETTING]. repeat steps 2 through 6. Use the [INSERTION TYPE B SETTING] key instead of the [INSERTION TYPE A SETTING] key, and the [INSERTION TYPE B] key instead of the [INSERTION TYPE A] key.
Copy_SEC.book 16 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Checking, editing, and deleting cover/insert pages The [PAGE LAYOUT] key appears after covers/inserts settings are configured (the settings of step 1 through step 7 on pages 5-13 and 5-14). The [PAGE LAYOUT] key is used for the following: ● To display the status of covers/inserts pages ● To edit, delete, or add inserted pages (3)To edit or delete the insertion page of an insert, To display the [PAGE LAYOUT] key...
Copy_SEC.book 17 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Examples of covers and inserts The relations between the originals and finished copies when covers or inserts are inserted are shown on the following pages.
Copy_SEC.book 18 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Covers (One-sided copying of one-sided originals) One-sided copies are made of the following one-sided originals.
Copy_SEC.book 19 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Covers (Two-sided copying of one-sided originals) Two-sided copies are made of the following one-sided originals.
Copy_SEC.book 20 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Covers (One-sided copying of Two-sided originals) One-sided copies are made of the following two-sided originals.
Copy_SEC.book 21 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Covers (Two-sided copying of two-sided originals) Two-sided copies are made of the following two-sided originals.
Copy_SEC.book 22 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Inserts (One-sided copying of one-sided originals) One-sided and two-sided copying is performed using the following one-sided originals. The insertion page of the insert is set to page 3.
Copy_SEC.book 23 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Transparency film with insert sheets When copying onto transparency film, blank insert sheets can be placed between transparent sheets. Example: Inserting insert sheets between transparencies ● This function only operates in "one-sided to onesided" and "two-sided to one-sided" modes. ● Multiple copies cannot be selected in this mode. ● The inserts are inserted under each transparency as shown at left.
Copy_SEC.book 24 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES 9 Select the tray 2. the insertion conditions for the insert 11 Set paper. OR COPY. OK AUTO ORIGIN 1. 81/2 x11 PLAIN 2. 81/2x11 TRANSPARENCY 3. 11x17 PLAIN PAPE 4. 81/2x11 PLAIN 100 COPY R CANCEL AUT EXPOS PRINT ON INSERT SHEETS YES NO To display the special modes screen... See "General procedure for using special functions" on page 5-2. [TRANSPARENCY INSERTS] special modes screen (2nd screen).
Copy_SEC.book 25 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES To display the special modes screen... See "General procedure for using special functions" on page 5-2. the [MULTI SHOT] key in the special 1 Touch modes screen (2nd screen). 2 TRANSPARENCY INSERTS MULTI SHOT CARD SHOT MIRROR IMAGE The MULTI SHOT setting screen will appear. A multi shot icon ( , etc.) will also appear in the upper left of the screen to indicate that the function is turned on.
Copy_SEC.book 26 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Book copy This function is convenient when you wish to compile copies of books or other bound originals into an attractive pamphlet format. The two pages of the open book are scanned as a set, and two pages each are copied onto the front and back sides of the copy paper (four pages are copied onto one sheet of copy paper). This allows the copies to be folded down the center and made into a pamphlet.
Copy_SEC.book 27 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Card shot When copying a card, this function allows you to combine the front and back sides on a single sheet of paper. This function is convenient for making copies for certification purposes and helps save paper. Original ● Copying is only possible on standard size paper. ● A copy ratio cannot be selected when using this function. ● The image cannot be rotated when using this function.
05.fm 28 ページ 2006年12月19日 火曜日 午後10時28分 SPECIAL MODES 4 Touch the outer [OK] key. OK CANCEL OK You will return to the main screen of copy mode. the back side of the original face 8 Place down on the document glass (see step 5). 9 Press the [START] key. SIZE RESET The back side of the card is scanned. FIT TO PAGE 5 Place the original on the document glass. Place the front side of the original face down and close the document cover.
Copy_SEC.book 29 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Mirror image This function is used to print a mirror image of the original. The images will be inverted in the right to left direction on the copies. Original Copy the [OK] key on the special modes 2 Touch screen. To display the special modes screen... See "General procedure for using special functions" on page 5-2. the [MIRROR IMAGE] key in 1 Touch special modes screen (2nd screen).
Copy_SEC.book 30 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES Print menu The date, a stamp, page numbers, and entered text can be printed on copies. Four selections are available for the PRINT MENU: • Date print (page 5-33) • Stamp (page 5-34) This prints the date on the paper. [Example] Printing 2010/APR/4 in the upper righthand corner of the paper Print a message such as "CONFIDENTIAL" in reverse text on the paper.
Copy_SEC.book 31 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Common operation procedure for using the print menu To display the special modes screen... See "General procedure for using special functions" on page 5-2. the [PRINT MENU] key in the special 1 Touch modes screen (3rd screen). B/W REVERSE The print menu setting screen will appear. The print menu icon ( ) will also appear in the upper left corner of the screen to indicate that the function is turned on.
Copy_SEC.book 32 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES the print layout if needed (page 58 Check 41). OK LAYOUT OK CANCEL 2-SIDED ORIGINAL TYPE S WHEN COPYING ON COVERS/INSERTS the [OK] 9 Touch setting screen. 2 To display the layout and print content of the configured print menu, touch the [LAYOUT] key. The position can be changed and settings canceled if needed. NOTE To cancel print menu... Touch the [CANCEL] key in the screen of step 3.
05.fm 33 ページ 2006年12月19日 火曜日 午後10時30分 SPECIAL MODES ■ Printing the date on copies The date can be printed on copies. Four selections each are available for the date format and the character that separates the year, month, and day. NOTE The date must be previously set in the system settings. (See page 2-14.) steps 1 and 2 of "Common 1 Follow operation procedure for using the print 5 Select the pages to be printed on. menu" (page 5-31). 2 CANCEL CURRENT SETTING Touch the [DATE] key.
Copy_SEC.book 34 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Printing a stamp (reverse text) on copies A message such as "CONFIDENTIAL" can be printed in reverse text on copies. The following 12 messages are available. CONFIDENTIAL PRIORITY PRELIMINARY FINAL FOR YOUR INFO. DO NOT COPY IMPORTANT COPY URGENT DRAFT TOP SECRET PLEASE REPLY You can select from three density levels for the background of the stamp. Two selections are available for the size of the stamp.
Copy_SEC.book 35 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Printing the page number on copies The page number can be printed on copies. One of 6 formats can be selected for the page number. steps 1 and 2 of "Common 1 Follow operation procedure for using the print menu" (page 5-31). 2 Touch the [PAGE NUMBERING] key. you need to change the starting or 4 Ifending number of page numbering, the first page printed on, or the print settings for covers/inserts, touch the [PAGE NUMBER] key.
Copy_SEC.book 36 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES covers/inserts are added and you 7 When wish to include the covers/inserts in the 9 Touch the [OK] key. page number count, touch the [COVERS/ INSERTS COUNTING] key. OK LAST NUMBER OK AUTO COVERS/INSERTS COUNTING LAST NUMBER AUTO COVERS/INSERTS COUNTING 10 Touch the [OK] key. the checkboxes of the items that 8 Select you wish to include in the page number count and then touch the [OK] key.
Copy_SEC.
Copy_SEC.
05.fm 39 ページ 2006年12月19日 火曜日 午後10時31分 SPECIAL MODES ■ Printing entered text on copies Entered text can be printed on copies. Up to 50 characters can be printed. Up to 30 sequences of frequently used text can be stored. See "Storing text sequences" (page 5-40). NOTE When the machine is connected to a network, the printed text sequences can be stored and deleted in the Web page. For details, see Help in the Web page.
05.fm 40 ページ 2006年12月19日 火曜日 午後10時32分 SPECIAL MODES Storing text sequences 1 Editing and deleting stored text Follow steps 1 and 2 of "Common operation procedure for using the print menu" (page 5-31). 2 Touch the [TEXT] key. steps 1 and 2 of "Common 1 Follow operation procedure for using the print menu" (page 5-31). 2 Touch the [TEXT] key. OK LAYOUT CANCEL OK LAYOUT OK CANCEL OK 1/2 1/2 DATE STAMP DATE STAMP PAGE NUMBERING TEXT PAGE NUMBERING TEXT 3 Touch the [STORE/DELETE] key.
Copy_SEC.book 41 ページ 2006年12月13日 水曜日 午後3時1分 SPECIAL MODES ■ Checking and changing the print layout You can check the print layout after the print items have been selected. If needed you can change the print position or delete print content. the [LAYOUT] key on the print menu 1 Touch screen. 4 Touch the key of the new position. The selected key is highlighted and the print position changes to the new position. OK LAYOUT DATE STAMP PAGE NUMBERING TEXT SELECTED ITEM.
Copy_SEC.book 42 ページ 2006年12月13日 水曜日 午後3時1分 STORING, USING AND DELETING JOB PROGRAMS The steps of up to 10 copy jobs can be stored as job programs. Job programs can be called up with ease, and are retained even when the power is turned off. By storing frequently used copy settings in a job program, you can eliminate the bother of selecting the settings each time you use them for a copy job.
Copy_SEC.book 43 ページ 2006年12月13日 水曜日 午後3時1分 STORING, USING AND DELETING JOB PROGRAMS Calling up a job program 1 Press the [#/P] key. the number of copies if needed and 3 Set then press the [START] key. Copying will begin using the settings of the job program. LOGOUT the number key of the desired job 2 Touch program. The screen automatically closes and the job program is called up. A number key that does not have a job program cannot be selected. JOB PROGRAMS PRESS PROGRAM NUMBER.
05.fm 44 ページ 2006年12月13日 水曜日 午後5時45分 INTERRUPTING A COPY RUN The copy of the original scanned in interrupt mode is output before the remainder of the interrupted copy job. 1 Touch the [INTERRUPT] key. If interrupt copying is possible during a copy run, the [INTERRUPT] AUTO ORIGINA key will appear. (If the key does not appear, AUTO EXPOSUR interrupt copying is not AUTO 8x possible.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 CHAPTER 6 MACHINE MAINTENANCE (FOR COPYING) This chapter explains procedures for cleaning the machine, and troubleshooting. Page USER MAINTENANCE ........................................................................... 6-2 ● Cleaning the document glass and the automatic document feeder ....... 6-2 ● Cleaning the main charger of the photoconductive drum....................... 6-2 TROUBLESHOOTING .................................................................
06.fm 2 ページ 2006年12月19日 火曜日 午後10時34分 USER MAINTENANCE Cleaning the document glass and the automatic document feeder If the document glass, document cover or automatic document scanning unit have dirty spots, these spots will form lines in scanned images. These will show up as defects when the images are printed. Always keep these parts clean. \ Wipe with a clean, soft cloth. If necessary, moisten the cloth with water or a small amount of neutral detergent. When finished, wipe dry with a clean cloth.
Copy_SEC.book 3 ページ 2006年12月13日 水曜日 午後3時1分 TROUBLESHOOTING Check the following troubleshooting list before requesting service as many problems can be fixed by the user. If you are unable to solve the problem by checking the list, turn off the power switch, and unplug the power cord. Problems related to the copy function are described below. For problems related to general use of the machine, see page 2-23. Problem Check Solution Machine does not Is the [START] key indicator off? operate.
Copy_SEC.
07-1.fm 1 ページ 2006年12月13日 水曜日 午後5時47分 CHAPTER 7 DOCUMENT FILING FUNCTION Page OVERVIEW ............................................................................................. 7-2 ● Document filing function.................................................................. 7-2 TO USE THE DOCUMENT FILING FUNCTION..................................... 7-4 ● A look at the operation panel .......................................................... 7-4 ● Saving files........................................
Copy_SEC.book 2 ページ 2006年12月13日 水曜日 午後3時1分 OVERVIEW Document filing function This function can only be used on the MX-M350N/MX-M450N, or when the document filing function has been added. The document filing function allows you to save a document image in the machine's hard disk as a data file. The image can be called up and printed or transmitted as needed. The scanned document image is saved when printing or transmitting a document in copy mode, printer mode, or image send mode ("QUICK FILE" or "FILE").
Copy_SEC.book 3 ページ 2006年12月13日 水曜日 午後3時1分 OVERVIEW ■ Quick File folder When [QUICK FILE FOLDER] is selected in the main screen of any of the modes, the file is saved in this folder. Up to 1000 files can be saved in the Quick File folder. All files in the Quick File Folder can be deleted using the administrator settings. If you have a file that you do not want deleted, set the file attribute to [PROTECT] (up to 500 files can be protected).
Copy_SEC.book 4 ページ 2006年12月13日 水曜日 午後3時1分 TO USE THE DOCUMENT FILING FUNCTION A look at the operation panel (1) (2) (3) DOCUMENT FILING IMAGE SEND (4) (5) (6) PRINT READY DATA LINE DATA COPY SYSTEM JOB STATUS SETTINGS LOGOUT (7) (1) Touch panel (see the next page) This displays messages and keys. Keys can be touched to select and enter settings. When a key is touched, a beep will sound and the key will be highlighted to indicate that it is selected.
Copy_SEC.book 5 ページ 2006年12月13日 水曜日 午後3時1分 TO USE THE DOCUMENT FILING FUNCTION Main screen of document filing To display the main screen of document filing, press the [DOCUMENT FILING] key when the touch panel shows the copy mode screen, image send mode, or the job status screen. The main screen shows messages, keys, and items that can be selected for document filing.
Copy_SEC.book 6 ページ 2006年12月13日 水曜日 午後3時1分 SAVING A DOCUMENT IMAGE FILE Quick File When printing or transmitting a document in copy mode, printer mode, or fax/image transmission mode, "QUICK FILE" can be selected to save an image of the document to the Quick File folder. The image can be called up at a later time, allowing you to print or transmit the document without having to locate the original.
Copy_SEC.book 7 ページ 2006年12月13日 水曜日 午後3時1分 SAVING A DOCUMENT IMAGE FILE Filing When printing or transmitting a document in copy mode, printer mode, or image send mode, "FILE" can be selected to save an image of the document to the main folder or a previously created custom folder. The image can be called up at a later time, allowing you to print or transmit the document without having to locate the original.
Copy_SEC.book 8 ページ 2006年12月13日 水曜日 午後3時1分 SAVING A DOCUMENT IMAGE FILE 9 Touch the [OK] key. FOLDER will return to the screen of step 10. 14 You The set password is displayed with " ". The touched folder is selected and you return to the screen of step 7. The selected folder name is displayed. OK 2/2 CANCEL OK PASSWORD XYYY needed, select the [CONFIDENTIAL] 10 Ifcheckbox (only in copy mode). When this is selected, the file is stored with the FILE INFORMATION attribute [CONFIDENTIAL].
Copy_SEC.book 9 ページ 2006年12月13日 水曜日 午後3時1分 SAVING A DOCUMENT IMAGE FILE Print jobs Print jobs sent to the machine using the machine's printer driver can be saved in the main folder or a previously created custom folder when printed. The saved print data can be called up and printed or transmitted without having to open the original file on your computer. This section gives an overview of this function and explains the procedure for printing from the operation panel of the machine.
Copy_SEC.book 10 ページ 2006年12月13日 水曜日 午後3時1分 SAVING A DOCUMENT IMAGE FILE Scan Save Scan save is used to save a scanned document image in the main folder or the custom folder without copying or transmitting it. the [DOCUMENT FILING] key on the 1 Press operation panel. any of the following steps 7 to 16 6 Perform as needed. When finished, go to step 17 on page 7-11. PRINT READY DATA DOCUMENT FILING ●To set the original size, perform steps 7 to 10.
Copy_SEC.book 11 ページ 2006年12月13日 水曜日 午後3時1分 SAVING A DOCUMENT IMAGE FILE 11 Touch the [RESOLUTION] key. 16 Touch the [OK] key. You will return to the screen of step 14. AUTO EXPOSURE OK 300x300dpi RESOLUTION MANUAL AUTO ORIGINAL the original and touch the [START] 17 Place key. 12 Touch the key of the desired resolution. PRESS [START] TO SCAN ORIGINAL.
Copy_SEC.book 12 ページ 2006年12月13日 水曜日 午後3時1分 SAVING A DOCUMENT IMAGE FILE ■ Using special functions for scan save Touch the [SPECIAL MODES] key in the main scan save screen to display the special modes screen. The functions below can be selected in this screen. READY TO SCAN TO HDD. PRESS [START] TO SCAN ORIGINAL. Touch the [SPECIAL MODES] key in the main screen. SCAN TO HDD BACK AUTO EXPOSURE 300x300dpi RESOLUTION SPECIAL MODES AUTO ORIGINAL FILE INFORMATION (1) (2) (3) [READY TO SCAN TO HDD.
07-2.fm 13 ページ 2006年12月19日 火曜日 午後10時38分 CALLING UP AND USING A FILE Searching for and calling up a saved file When calling up a file, you can enter the file name, folder name, or user name to quickly search for the file. To search for a file, touch the [SEARCH] key in the main screen of document filing mode or in a screen that shows folders or files in a folder. A data search screen will appear.
Copy_SEC.book 14 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE results of the user name search 7 The appear. Touch the desired file name or folder name. name or folder name.
Copy_SEC.book 15 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE Calling up and using a saved file A file saved with the document filing function can be called up and printed or manipulated as needed. The following operations can be performed: ● [Print] : Print the file (page 7-17). ● [Send] : Transmit the saved file (page 7-20). The file can be transmitted by Scan to E-mail, Scan to FTP, Scan to Network Folder, fax, or Internet fax.
Copy_SEC.book 16 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE the key of the operation that you 5 Touch wish to perform. (1) (2) (1) [PRINT] key (see below) (2) [SEND] key (see page 7-20) (3) [PROPERTY CHANGE] key (see page 7-21) (3) (4) [MOVE] key (see page 7-22) CANCEL JOB SETTINGS Basic specifications Yamada Taro 8 1/2"x11" (5) [DELETE] key (see page 7-22) SELECT THE JOB.
Copy_SEC.book 17 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE ■ [Print] A saved file can be printed. The screen below appears when the [PRINT] key is selected in the operation selection screen. To begin printing, touch the [PRINT] (7) key. Printing settings can be selected in this screen before printing. The settings that were in effect when the file was saved appear initially. The settings can be changed as needed.
Copy_SEC.book 18 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE ■ Batch printing All files in a folder that have the same user name and password can be printed at once. the [BATCH P.] key in the file list 1 Touch screen of document filing mode. has been established, touch 4 Ifthea password [PASSWORD] key. To print all files of a specific type of job, touch the desired job tab. The files shown on that tab can be printed as a batch.
Copy_SEC.book 19 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE 8 Touch the [OK] key. the [PRINT AND DELETE THE 9 Touch DATA] key or the [PRINT AND SAVE THE DATA] key. CANCEL OK If the [PRINT AND DELETE THE DATA] key PRINT AND DELETE THE DATA is touched, the files will PRINT AND SAVE THE DATA be automatically deleted after printing. If the [PRINT AND SAVE THE DATA] key is touched, the files will be saved after printing.
Copy_SEC.book 20 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE ■ [Send] A saved file can be transmitted by Scan to E-mail, Scan to FTP, Scan to Network Folder, fax, or Internet fax. These transmission methods require installation of the appropriate options. The following screen appears when the [SEND] key is touched. Select the destination and other settings required for transmission and then touch the [SEND] (10) key to transmit the file.
Copy_SEC.book 21 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE (11) [SEND SETTINGS] key [SEND SETTINGS] key is displayed in scanner mode and Internet FAX mode. Touch this key to set the subject and file name. In scanner mode, the sender name can also be set. (12) [SUB ADDRESS] key or [ADDRESS ENTRY] key ● Touch this key to directly enter the destination for a Scan to E-mail, Scan to FTP, Scan to Network Folder or Internet fax transmission.
Copy_SEC.book 22 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE ■ [Move] ■ [Delete] This operation is used to move a file to a different folder. The following screen appears when the [MOVE] key is selected. Only [SHARING] and [CONFIDENTIAL] files can be moved. A [PROTECT] file can be moved by first using [PROPERTY CHANGE] to change the attribute to [SHARING] or [CONFIDENTIAL].
Copy_SEC.book 23 ページ 2006年12月13日 水曜日 午後3時1分 CALLING UP AND USING A FILE ■ Calling up and manipulating a file from the job status screen Files saved using the "FILE" and "QUICK FILE" functions appear as keys in the finished job status screen. You can view information on a file that appears in this screen and manipulate the file. Press the [JOB STATUS] key. 1 AGE SEND DATA view information on the file, touch the 4 To [DETAIL] key. The job status screen appears. COPY Use the keys to change screens.
Copy_SEC.book 24 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS Creating, editing, and deleting user names and folders This section explains how to create, edit, and delete user names and custom folders for saving files with the document filing function. User names and custom folders are created and edited at the operation panel of the machine or in the Web page. NOTES ● A previously stored name cannot be used when creating a new user name or custom folder.
Copy_SEC.book 25 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS ■ Programming a user name To program a user name, follow steps 1 and 2 on page 7-24, touch the [USER NAME REGISTRATION] key in step 3, and then follow these steps: 1 Touch the [USER NAME] key. The lowest number that has not yet been USER NAME programmed appears PASSWORD automatically in "No.". Touch the number to SELECT THE DEFAULT FOLDER THE F STORED TO: display a character entry screen and enter a user name (maximum of 16 characters).
Copy_SEC.book 26 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS ■ Editing and deleting a user name To edit or delete a user name, follow steps 1 and 2 on page 7-24 and then follow these steps: the [AMEND/DELETE USER NAME] 1 Touch key. OK [Editing] the key of each item that you wish to 4 Touch edit (edit as explained in steps 1 to 9 in "Programming a user name" on page 725). AMEND/DELETE USER NAME AMEND/DELETE CUSTOM FOLDER USER NAME / AMEND/DELETE No.001 REGISTRATION IS COMPLETED.
Copy_SEC.book 27 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS ■ Creating a custom folder Up to 500 custom folders can be created. When no further folders can be created, delete unneeded folders (page 7-28) and then create a new folder. A password can be omitted when creating a folder. To create a custom folder, follow steps 1 and 2 on page 7-24, touch the [CUSTOM FOLDER REGISTRATION] key in step 3, and then follow the steps below. 1 Touch the [FOLDER NAME] key.
Copy_SEC.book 28 ページ 2006年12月13日 水曜日 午後3時1分 SYSTEM SETTINGS 9 Touch the [OK] key. exit, touch the [EXIT] key. To create 10 To another folder, touch the [NEXT] key. If you touched the [EXIT] key, you will return to the screen of step 3 on page 7-24. If you touched the [NEXT] key, a new folder screen will appear. Repeat steps 1 to 10 to OK ADD NEW JKLMN OPQRST EXIT NEXT 1/1 SWORD UVWXYZ create a new folder.
Copy_SEC.book 29 ページ 2006年12月13日 水曜日 午後3時1分 ENTERING CHARACTERS To enter or edit characters in setting screens such as auto dial key programming screens, follow the steps below. Characters that can be entered are alphabetical characters, special characters, numbers, and symbols. ■ Entering alphabetical characters (Example: Sharp äÄ) 1 Touch the [S] key. 5 Touch the [ Characters cannot be entered beyond the " " mark. ÃÄÂ/ãäâ] key. Sharp 6 Touch the [ä] key.
07-3.fm 30 ページ 2007年3月14日 水曜日 午前11時23分 ENTERING CHARACTERS ■ Entering numbers and symbols 1 Touch the [AB/ab 12#$%] key. you have finished 3 When characters, touch the [OK] key. entering 1&1 When the characters "12#$%" are highlighted, number/symbol entry mode is selected. the desired number or symbol. 2 Enter Numbers and symbols that can be entered are as follows: Screen 1/2 Screen 2/2 Change screens by touching the key or key displayed in the screen.
Copy_SEC.book 31 ページ 2006年12月13日 水曜日 午後3時1分 TROUBLESHOOTING This section explains problems frequently encountered when using the document filing function. If you experience any difficulty, refer to the following table. For information on general machine problems, printer problems, fax problems, and network scanner problems, please see the troubleshooting sections of the appropriate manuals. Problem Check Cause and solution A saved file has disappeared.
Copy_SEC.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 CHAPTER 8 SPECIFICATIONS This chapter contains useful information about the machine. Page SPECIFICATIONS................................................................................... 8-2 LIST OF COMBINATION OF PERIPHERAL DEVICES .......................... 8-4 INDEX .....................................................................................................
08.fm 2 ページ 2006年12月20日 水曜日 午後8時32分 SPECIFICATIONS Type Console Print system Electrophotographic system Photoconductive type OPC drum Developer system Dry-type two-component magnetic brush development Fusing system Heater roller Resolution Scan: 600 x 600 dpi, output: 600 x 600 dpi Gradation 256 levels Originals Sheets, bound documents Maximum size: 11" x 17" or A3 Copy paper Plain paper and special papers Copy sizes Max. 11" x 17" or A3, min.
Copy_SEC.book 3 ページ 2006年12月13日 水曜日 午後3時1分 SPECIFICATIONS Continuous copying speed (when the offset function is not used) MX-M350N/MX-M350U Copy paper size MX-M450N/MX-M450U 100% / Reduced / Enlarged 11" x 17" (A3) 17 copies/min. 20 copies/min. 8-1/2" x 14" (B4) 20 copies/min. 22 copies/min. 8-1/2" x 11" (A4) 35 copies/min. 45 copies/min. 8-1/2" x 11"R (A4R) 25 copies/min. 30 copies/min. 7-1/4" x 10-1/2" (B5) 35 copies/min. 45 copies/min. 7-1/4" x 10-1/2"R (B5R) 25 copies/min.
Copy_SEC.book 4 ページ 2006年12月13日 水曜日 午後3時1分 LIST OF COMBINATION PERIPHERAL DEVICES OF The table below shows the possible system configurations. Some devices require the installation of others (B) to be functional and some cannot be installed together (A).
Copy_SEC.book 5 ページ 2006年12月13日 水曜日 午後3時1分 INDEX [ ] key................................................................. 1-13 [#/P] key ............................................................... 1-13 ■ Numerics 1-sided copy -Automatic document feeder ............................... 4-7 -Document glass ............................................... 4-11 2in1 ............................................................. 5-24, 7-12 2-sided copy .........................................
Copy_SEC.book 6 ページ 2006年12月13日 水曜日 午後3時1分 INDEX Examples of covers and inserts ............... 5-17 to 5-22 -Covers.................................................. 5-18 to 5-21 -Inserts .............................................................. 5-22 External account module............................. 1-12, 3-27 Exit tray .................................................. 1-9, 1-11, 3-2 ■ F Facsimile expansion kit ........................................ 1-12 Fax data receive/forward ............
Copy_SEC.book 7 ページ 2006年12月13日 水曜日 午後3時1分 INDEX ■ P Page numbering .......................1-7, 5-30, 5-35 to 5-38 Pamphlet copy.......................................... 1-4, 5-2, 5-6 Paper curled ......................................................... 2-24 Paper tray ...................................................... 1-9, 2-20 Paper tray settings ........................................ 2-5, 2-14 Part names -Duplex module ................................................... 3-2 -Exterior .........
Copy_SEC.book 8 ページ 2006年12月13日 水曜日 午後3時1分 INDEX ■ T Tandem copy ............................................ 1-5, 5-2, 5-9 Text..............................................1-7, 4-14, 5-30, 5-39 Text/photo............................................................. 4-14 The machine does not operate ..................... 2-23, 6-3 Toner cartridge ............................................ 1-10, 2-15 Top cover................................................ 3-5, 3-7, 3-14 Top tray......................
Copy_SEC.
Copy_SEC.
Copy_SEC.book 1 ページ 2006年12月13日 水曜日 午後3時1分 NOTICE BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection, Sharp extends a limited warranty to each of its authorized dealers and, in turn, requires each of its authorized dealers to extend its own warranty to you on terms that are no less favorable than those given to the dealer by Sharp.
Cover4.fm 1 ページ 2007年3月14日 水曜日 午前11時28分 MX-M350U/MX-M450U/MX-M350N/MX-M450N OPERATION MANUAL (for general information and copier operation) SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163. www.sharpusa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 This manual has been printed using a vegetable-based soy oil ink to help protect the environment.
MX-M350U/MX-M450U/MX-M350N/MX-M450N ADMINISTRATOR SETTINGS GUIDE CHINA KS1 80FCZZ ADMINISTRATOR SETTINGS GUIDE LASER PRINTER This manual explains settings for use by the administrator of the machine.
JupiterII_Admin_sec.
JupiterII_Admin_sec.book 1 ページ 2006年12月12日 火曜日 午後5時39分 Contents page ●PURPOSE OF THE ADMINISTRATOR SETTINGS ............................................................................1 ●ADMINISTRATOR SETTINGS LIST ....................................................................................................3 ●USING THE ADMINISTRATOR SETTINGS.........................................................................................4 ●GENERAL SETTINGS ................................................
JupiterII_Admin_sec.fm 2 ページ 2006年12月19日 火曜日 午後8時25分 PURPOSE OF THE ADMINISTRATOR SETTINGS Document filing settings These settings can be used to change the factory default settings for the document filing function as needed to suit the needs of your workplace. This function can only be used on the MX-M350N/MX-M450N, or when the document filing function has been added.
JupiterII_Admin_sec.fm 3 ページ 2007年3月8日 木曜日 午後3時46分 ADMINISTRATOR SETTINGS LIST Settings for general use of the machine, the copy function, and the document filing function are shown in the following list. The administrator password must be entered in order to use these programs. NOTE The administrator settings that can be accessed depend on the optional equipment that is installed.
JupiterII_Admin_sec.fm 4 ページ 2006年12月19日 火曜日 午後8時26分 USING THE ADMINISTRATOR SETTINGS The procedure for configuring the administrator password is explained below using the "Change admin password" as an example. Follow the same steps to configure the settings that are described beginning on page 7. 1 Press the [SYSTEM SETTINGS] key. PY SYSTEM JOB STATUS SETTINGS the [ADMINISTRATOR SETTINGS] 2 Touch key.
JupiterII_Admin_sec.book 5 ページ 2006年12月12日 火曜日 午後5時39分 USING THE ADMINISTRATOR SETTINGS Additional information on using the keys to configure administrator settings These keys and indicator are available on setting screens that require the entry of numerical values.
JupiterII_Admin_sec.fm 6 ページ 2007年3月8日 木曜日 午後3時47分 USING THE ADMINISTRATOR SETTINGS Administrator settings menu The administrator settings are arranged in the following menu. Refer to this menu when enabling or disabling the settings that are explained beginning on the following page. * Some items contain an additional level of settings.
JupiterII_Admin_sec.book 7 ページ 2006年12月12日 火曜日 午後5時39分 GENERAL SETTINGS Administrator settings for general use of the machine are explained in this section. Account control "Account control" consists of the following settings.
JupiterII_Admin_sec.book 8 ページ 2006年12月12日 火曜日 午後5時39分 GENERAL SETTINGS Resetting account This setting is used to reset the printed page count and transmitted page count of an account to "0". Touch the [RESETTING ACCOUNT] key to display the following screen.
JupiterII_Admin_sec.book 9 ページ 2006年12月12日 火曜日 午後5時39分 GENERAL SETTINGS Job log control Clear all job log data The machine keeps a log of the jobs it has run. The job log can be used to check general use of the machine. The job log can be written to your computer in CSV format using a Web browser. This setting is used to clear the job log. There is normally no need to use the program. Energy save "Energy save" provides the following settings to reduce your power costs.
JupiterII_Admin_sec.
JupiterII_Admin_sec.book 11 ページ 2006年12月12日 火曜日 午後5時39分 GENERAL SETTINGS Disabling switching of display order This setting is used to disable the function that changes the key display order each time a selected tab is touched on a screen that is divided into tabs, including the screens for selecting the user name and folder for the "SCAN TO HDD" and "FILE" functions, and the address book screen of image send mode.
JupiterII_Admin_sec.book 12 ページ 2006年12月12日 火曜日 午後5時39分 GENERAL SETTINGS Saddle stitch position adjust This setting is used to adjust the stapling position (folding position) when using the saddle stitch function of the optional saddle stitch finisher. The value can be adjusted in 0.1 mm increments within ±3.0 mm from the reference position for each paper size. Max.+3mm Min.
JupiterII_Admin_sec.book 13 ページ 2006年12月12日 火曜日 午後5時39分 GENERAL SETTINGS Network settings These settings are set when this product is used as a network printer. After you complete the setting for one setting, you must exit the administrator settings, turn off the main switch, wait briefly, and then turn on the main switch again before any other settings can be set. The setting that was set will be effective after the power is turned on. The following items can be configured in the "Network settings".
GENERAL SETTINGS PING command This setting is used to check if the machine and a computer connected to the network can communicate. Enter the IP address of the computer that you wish to check and touch the [START] key. A message will appear indicating whether or not there was a response from the computer. Security settings The following settings are related to security. Touch the [SECURITY SETTINGS] key to configure the settings.
JupiterII_Admin_sec.fm 15 ページ 2007年3月8日 木曜日 午後3時47分 GENERAL SETTINGS Product key Initialize and/or store settings Use these settings to enter the product keys for the following options. These settings are used to return the administrator settings to the factory default settings, to store the current settings, and to restore stored administrator settings. (Note that this also includes printer configuration settings.
JupiterII_Admin_sec.book 16 ページ 2006年12月12日 火曜日 午後5時39分 COPY SETTINGS This section explains the administrator settings that are used for copy mode.
JupiterII_Admin_sec.book 17 ページ 2006年12月12日 火曜日 午後5時39分 COPY SETTINGS Initial margin shift setting This setting is used to set the initial margin shift amount. The initial margin shift amount can be set from 0" to 1" (0 mm to 20 mm) in increments of 1/8" (1 mm). Normally the margin shift is set to 1/2" (10 mm) for both the front and back of the paper. Erase width adjustment This setting is used to set the initial width of edge erase copying.
JupiterII_Admin_sec.book 18 ページ 2006年12月12日 火曜日 午後5時39分 DOCUMENT FILING SETTINGS This section explains administrator settings for the document filing function. This function can only be used on the MX-M350N/MX-M450N, or when the document filing function has been added.
JupiterII_Admin_sec.book 19 ページ 2006年12月12日 火曜日 午後5時39分 DOCUMENT FILING SETTINGS Scan complete sound setting The volume of the beep that alerts you when scanning of an original has finished can be adjusted to two levels. The beep can also be turned off. Initial resolution setting This is used to change the default resolution setting for "SCAN TO HDD" of the document filing function. The default resolution is initially set to "600x600dpi".
JupiterII_Admin_sec.
JupiterII_Admin_sec.book 21 ページ 2006年12月12日 火曜日 午後5時39分 ✂ Administrator Name: Contact at: Information that the administrator of the machine requires is printed on the back of this page. (Separate this page from the manual and keep it in a safe place. In addition, fill in the name of the administrator and the administrator's contact information in the left hand margin.
JupiterII_Admin_sec.book 22 ページ 2006年12月12日 火曜日 午後5時39分 TO THE ADMINISTRATOR OF THE MACHINE (Separate this page from the manual and keep it in a safe place.) Factory default passwords (Web pages) There are two factory default accounts: "Administrator" and "User". A person who logs in as an "Administrator" can configure all settings in the Web pages. A person who logs in as a "User" can only configure certain settings. The factory default passwords are shown below.
JupiterII_Admin_sec.
JupiterII_Admin_sec.
JupiterII_Admin_sec.
cover3-4.fm 2 ページ 2007年4月10日 火曜日 午後12時55分 MX-M350U/MX-M450U/MX-M350N/MX-M450N ADMINISTRATOR SETTINGS GUIDE SHARP ELECTRONICS CORPORATION 1 Sharp Plaza, Mahwah, New Jersey 07430-1164. www.sharpusa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 This manual has been printed using a vegetable-based soy oil ink to help protect the environment.